[ Upstream commit 7d388551b6 ]
Some non-jedec compliant flashes (like the Everspin flashes) don't have
an ID at all. Hide the attribute in this case.
Fixes: 36ac022862 ("mtd: spi-nor: add initial sysfs support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-2-michael@walle.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2c135619c ]
inet_csk_bind_conflict() can access sk->sk_bound_dev_if for
unlocked sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3dc3f8e49 ]
dma_alloc_coherent does not return a physical address, but a DMA address,
which might be remapped or have an offset. Passing the DMA address to
vm_iomap_memory is thus broken.
Use the proper dma_mmap_coherent helper instead, and stop passing
__GFP_COMP to dma_alloc_coherent, as the memory management inside the
DMA allocator is hidden from the callers and does not require it.
With this the gfp_t argument to __videobuf_dc_alloc can be removed and
hard coded to GFP_KERNEL.
Fixes: a8f3c203e1 ("[media] videobuf-dma-contig: add cache support")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b434422c45 ]
A problem about modprobe s5p_fimc failed is triggered with the
following log given:
[ 272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy
The reason is that fimc_md_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregister fimc_driver, resulting the
s5p_fimc can never be installed later.
A simple call graph is shown as below:
fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister fimc_driver
Fix by unregister fimc_driver when platform_driver_register() returns
error.
Fixes: d3953223b0 ("[media] s5p-fimc: Add the media device driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f5866dd96 ]
If device_register() returns error in solo_sysfs_init(), the
name allocated by dev_set_name() need be freed. As comment of
device_register() says, it should use put_device() to give up
the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup().
Fixes: dcae5dacbc ("[media] solo6x10: sync to latest code from Bluecherry's git repo")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba8d940593 ]
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
Call Trace:
...
dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge]
platform_probe+0xb6/0x170
...
Allocated by task 1238:
...
dvb_register_device+0x1a7/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
Freed by task 1238:
dvb_register_device+0x6d2/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
It is because the error handling in vidtv_bridge_dvb_init() is wrong.
First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but
goto fail_dmx(_dev): calls release functions again, which causes
use-after-free.
Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause
out-of-bound when i finished its loop (i == NUM_FE). And the loop
releasing is wrong, although now NUM_FE is 1 so it won't cause problem.
Fix this by correctly releasing everything.
Fixes: f90cf6079b ("media: vidtv: add a bridge driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a85fbd6498 ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6d1918794 ]
If we get an error (other than -ENOENT) we need to propagate that up the
stack. Otherwise if the nvmem driver hasn't probed yet, we'll end up
end up claiming that we support all the OPPs which is not likely to be
true (and on some generations impossible to be true, ie. if there are
conflicting OPPs).
v2: Update commit msg, gc unused label, etc
v3: Add previously missing \n's
Fixes: fe7952c629 ("drm/msm: Add speed-bin support to a618 gpu")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511690/
Link: https://lore.kernel.org/r/20221115154637.1613968-1-robdclark@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af7749047 ]
This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.
Fixes: 0b523ced9a ("ath10k: add basic skeleton to support ahb")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221110061926.18163-1-xiujianfeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d90db3b1c8 ]
Zero out the pointer to ->slave_dir so that the holder code doesn't
incorrectly treat the object as alive when add_disk failed or after
del_gendisk was called.
Fixes: 89f871af1b ("dm: delay registering the gendisk")
Reported-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Link: https://lore.kernel.org/r/20221115141054.1051801-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25369175ce ]
The input parameter @fields is type of struct ima_template_field ***, so
when allocates array memory for @fields, the size of element should be
sizeof(**field) instead of sizeof(*field).
Actually the original code would not cause any runtime error, but it's
better to make it logically right.
Fixes: adf53a778a ("ima: new templates management mechanism")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39419ef7af ]
Key restriction is allocated in integrity_init_keyring(). However, if
keyring allocation failed, it is not freed, causing memory leaks.
Fixes: 2b6aa412ff ("KEYS: Use structure to capture key restriction function and data")
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b230555f32 ]
These formats are not subsampled, but that means hsub and vsub should be
1, not 0.
Fixes: 94b292b277 ("drm: drm_fourcc: add NV15, Q410, Q401 YUV formats")
Reported-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913144306.17279-1-brian.starkey@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 006ea1b582 ]
Adds a format that is 3 10bit YUV 4:2:0 samples packed into
a 32bit word (with 2 spare bits).
Supported on Broadcom BCM2711 chips.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20211215091739.135042-2-maxime@cerno.tech
Stable-dep-of: b230555f32 ("drm/fourcc: Fix vsub/hsub for Q410 and Q401")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd801b2265 ]
PMR735a has a wider range than previously defined. Fix it.
Fixes: c4e5aa3dbe ("regulator: qcom-rpmh: Add PM7325/PMR735A regulator support")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221110210706.80301-1-konrad.dybcio@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcaf434b8f ]
In nvme_init_non_mdts_limits function we were returning 0 when kzalloc
failed; it now returns -ENOMEM.
Fixes: 5befc7c26e ("nvme: implement non-mdts command limits")
Signed-off-by: Joel Granados <j.granados@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d27252b570 ]
In the PP_OD_EDIT_VDDC_CURVE case the "input_index" variable is capped at
2 but not checked for negative values so it results in an out of bounds
read. This value comes from the user via sysfs.
Fixes: d5bf265394 ("drm/amd/powerplay: added vega20 overdrive support V3")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2b41b748c ]
I got the the following report:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@62/regulators/exten
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called.
Fixes: 69511a452e ("regulator: map consumer regulator based on device tree")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221115091508.900752-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa8f9ac423 ]
There is no need to have a separate slab cache for each namespace,
and having separate ones creates duplicate debugs file names as well.
Fixes: d5eff33ee6 ("nvmet: add simple file backed ns support")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd0afbf15 ]
GCC 11.3.0 fails to compile btf_dump.c due to the following error,
which seems to originate in btf_dump_struct_data where the returned
value would be uninitialized if btf_vlen returns zero.
btf_dump.c: In function ‘btf_dump_dump_type_data’:
btf_dump.c:2363:12: error: ‘err’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2363 | if (err < 0)
| ^
Fixes: 920d16af9b ("libbpf: BTF dumper support for typed data")
Signed-off-by: David Michael <fedora.dm0@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Alan Maguire <alan.maguire@oracle.com>
Link: https://lore.kernel.org/bpf/87zgcu60hq.fsf@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff446c0f62 ]
Modify dpi power on/off sequence so that the first gpio operation will
take effect.
Fixes: 6bd4763fd5 ("drm/mediatek: set dpi pin mode to gpio low to avoid leakage current")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10276a20be ]
When the radeon driver reads the bios information from ACPI
table in radeon_acpi_vfct_bios(), it misses to call acpi_put_table()
to release the ACPI memory after the init, so add acpi_put_table()
properly to fix the memory leak.
v2: fix text formatting (Alex)
Fixes: 268ba0a99f ("drm/radeon: implement ACPI VFCT vbios fetch (v3)")
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1795c2ccb ]
This fixes crashes in bfq_add_bfqq_busy due to waker_bfqq being NULL,
but woken_list_node still being hashed. This would happen when
bfq_init_rq() expects a brand new allocated queue to be returned from
bfq_get_bfqq_handle_split() and unconditionally updates waker_bfqq
without resetting woken_list_node. Since we can always return oom_bfqq
when attempting to allocate, we cannot assume waker_bfqq starts as NULL.
Avoid setting woken_bfqq for oom_bfqq entirely, as it's not useful.
Crashes would have a stacktrace like:
[160595.656560] bfq_add_bfqq_busy+0x110/0x1ec
[160595.661142] bfq_add_request+0x6bc/0x980
[160595.666602] bfq_insert_request+0x8ec/0x1240
[160595.671762] bfq_insert_requests+0x58/0x9c
[160595.676420] blk_mq_sched_insert_request+0x11c/0x198
[160595.682107] blk_mq_submit_bio+0x270/0x62c
[160595.686759] __submit_bio_noacct_mq+0xec/0x178
[160595.691926] submit_bio+0x120/0x184
[160595.695990] ext4_mpage_readpages+0x77c/0x7c8
[160595.701026] ext4_readpage+0x60/0xb0
[160595.705158] filemap_read_page+0x54/0x114
[160595.711961] filemap_fault+0x228/0x5f4
[160595.716272] do_read_fault+0xe0/0x1f0
[160595.720487] do_fault+0x40/0x1c8
Tested by injecting random failures into bfq_get_queue, crashes go away
completely.
Fixes: 8ef3fc3a04 ("block, bfq: make shared queues inherit wakers")
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221108181030.1611703-1-khazhy@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8889a711f9 ]
ack.bufferSize should be set to 0 when generating an ack.
Fixes: 8d94aa381d ("rxrpc: Calls shouldn't hold socket refs")
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d96f690a ]
Provide a CONFIG_PROC_FS=n fallback for proc_create_net_single_write().
Also provide a fallback for proc_create_net_data_write().
Fixes: 564def7176 ("proc: Add a way to make network proc files writable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8f3582345 ]
It is required to return the received buffers, if streaming can not be
started. For instance media_pipeline_start() may fail with EPIPE, if
a link validation between entities is not passed, and in such a case
a user gets a kernel warning:
WARNING: CPU: 1 PID: 520 at drivers/media/common/videobuf2/videobuf2-core.c:1592 vb2_start_streaming+0xec/0x160
<snip>
Call trace:
vb2_start_streaming+0xec/0x160
vb2_core_streamon+0x9c/0x1a0
vb2_ioctl_streamon+0x68/0xbc
v4l_streamon+0x30/0x3c
__video_do_ioctl+0x184/0x3e0
video_usercopy+0x37c/0x7b0
video_ioctl2+0x24/0x40
v4l2_ioctl+0x4c/0x70
The fix is to correct the error path in video_start_streaming() of camss.
Fixes: 0ac2586c41 ("media: camss: Add files which handle the video device nodes")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8f6efccbb ]
When using wpa_supplicant v2.10, this driver is no longer able to
associate with any AP and fails in the EAPOL 4-way handshake while
sending the 2/4 message to the AP. The problem is not present in
wpa_supplicant v2.9 or older. The problem stems from HostAP commit
144314eaa ("wpa_supplicant: Send EAPOL frames over nl80211 where available")
which changes the way EAPOL frames are sent, from them being send
at L2 frames to them being sent via nl80211 control port.
An EAPOL frame sent as L2 frame is passed to the WiFi driver with
skb->protocol ETH_P_PAE, while EAPOL frame sent via nl80211 control
port has skb->protocol set to ETH_P_802_3 . The later happens in
ieee80211_tx_control_port(), where the EAPOL frame is encapsulated
into 802.3 frame.
The rsi_91x driver handles ETH_P_PAE EAPOL frames as high-priority
frames and sends them via highest-priority transmit queue, while
the ETH_P_802_3 frames are sent as regular frames. The EAPOL 4-way
handshake frames must be sent as highest-priority, otherwise the
4-way handshake times out.
Therefore, to fix this problem, inspect the skb control flags and
if flag IEEE80211_TX_CTRL_PORT_CTRL_PROTO is set, assume this is
an EAPOL frame and transmit the frame via high-priority queue just
like other ETH_P_PAE frames.
Fixes: 0eb42586cf ("rsi: data packet descriptor enhancements")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221104163339.227432-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac1c5a03d3 ]
USB controllers on SM8250 doesn't work after coming back from suspend.
This can be fixed by keeping the USB GDSCs in retention mode so that
hardware can keep them ON and put into rentention mode once the parent
domain goes to a low power state.
Fixes: 3e5770921a ("clk: qcom: gcc: Add global clock controller driver for SM8250")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221102091320.66007-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 529409ea92 ]
When equivalent completed state is found and it has additional precision
restrictions, BPF verifier propagates precision to
currently-being-verified state chain (i.e., including parent states) so
that if some of the states in the chain are not yet completed, necessary
precision restrictions are enforced.
Unfortunately, right now this happens only for the last frame (deepest
active subprogram's frame), not all the frames. This can lead to
incorrect matching of states due to missing precision marker. Currently
this doesn't seem possible as BPF verifier forces everything to precise
when validated BPF program has any subprograms. But with the next patch
lifting this restriction, this becomes problematic.
In fact, without this fix, we'll start getting failure in one of the
existing test_verifier test cases:
#906/p precise: cross frame pruning FAIL
Unexpected success to load!
verification time 48 usec
stack depth 0+0
processed 26 insns (limit 1000000) max_states_per_insn 3 total_states 17 peak_states 17 mark_read 8
This patch adds precision propagation across all frames.
Fixes: a3ce685dd0 ("bpf: fix precision tracking")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20221104163649.121784-3-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27113c59b6 ]
Every 8 bytes of the stack is tracked by a bpf_stack_state.
Within each bpf_stack_state, there is a 'u8 slot_type[8]' to track
the type of each byte. Verifier tests slot_type[0] == STACK_SPILL
to decide if the spilled reg state is saved. Verifier currently only
saves the reg state if the whole 8 bytes are spilled to the stack,
so checking the slot_type[7] is the same as checking slot_type[0].
The later patch will allow verifier to save the bounded scalar
reg also for <8 bytes spill. There is a llvm patch [1] to ensure
the <8 bytes spill will be 8-byte aligned, so checking
slot_type[7] instead of slot_type[0] is required.
While at it, this patch refactors the slot_type[0] == STACK_SPILL
test into a new function is_spilled_reg() and change the
slot_type[0] check to slot_type[7] check in there also.
[1] https://reviews.llvm.org/D109073
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210922004934.624194-1-kafai@fb.com
Stable-dep-of: 529409ea92 ("bpf: propagate precision across all frames, not just the last one")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3b666bfa9 ]
When processing ALU/ALU64 operations (apart from BPF_MOV, which is
handled correctly already; and BPF_NEG and BPF_END are special and don't
have source register), if destination register is already marked
precise, this causes problem with potentially missing precision tracking
for the source register. E.g., when we have r1 >>= r5 and r1 is marked
precise, but r5 isn't, this will lead to r5 staying as imprecise. This
is due to the precision backtracking logic stopping early when it sees
r1 is already marked precise. If r1 wasn't precise, we'd keep
backtracking and would add r5 to the set of registers that need to be
marked precise. So there is a discrepancy here which can lead to invalid
and incompatible states matched due to lack of precision marking on r5.
If r1 wasn't precise, precision backtracking would correctly mark both
r1 and r5 as precise.
This is simple to fix, though. During the forward instruction simulation
pass, for arithmetic operations of `scalar <op>= scalar` form (where
<op> is ALU or ALU64 operations), if destination register is already
precise, mark source register as precise. This applies only when both
involved registers are SCALARs. `ptr += scalar` and `scalar += ptr`
cases are already handled correctly.
This does have (negative) effect on some selftest programs and few
Cilium programs. ~/baseline-tmp-results.csv are veristat results with
this patch, while ~/baseline-results.csv is without it. See post
scriptum for instructions on how to make Cilium programs testable with
veristat. Correctness has a price.
$ ./veristat -C -e file,prog,insns,states ~/baseline-results.csv ~/baseline-tmp-results.csv | grep -v '+0'
File Program Total insns (A) Total insns (B) Total insns (DIFF) Total states (A) Total states (B) Total states (DIFF)
----------------------- -------------------- --------------- --------------- ------------------ ---------------- ---------------- -------------------
bpf_cubic.bpf.linked1.o bpf_cubic_cong_avoid 997 1700 +703 (+70.51%) 62 90 +28 (+45.16%)
test_l4lb.bpf.linked1.o balancer_ingress 4559 5469 +910 (+19.96%) 118 126 +8 (+6.78%)
----------------------- -------------------- --------------- --------------- ------------------ ---------------- ---------------- -------------------
$ ./veristat -C -e file,prog,verdict,insns,states ~/baseline-results-cilium.csv ~/baseline-tmp-results-cilium.csv | grep -v '+0'
File Program Total insns (A) Total insns (B) Total insns (DIFF) Total states (A) Total states (B) Total states (DIFF)
------------- ------------------------------ --------------- --------------- ------------------ ---------------- ---------------- -------------------
bpf_host.o tail_nodeport_nat_ingress_ipv6 4448 5261 +813 (+18.28%) 234 247 +13 (+5.56%)
bpf_host.o tail_nodeport_nat_ipv6_egress 3396 3446 +50 (+1.47%) 201 203 +2 (+1.00%)
bpf_lxc.o tail_nodeport_nat_ingress_ipv6 4448 5261 +813 (+18.28%) 234 247 +13 (+5.56%)
bpf_overlay.o tail_nodeport_nat_ingress_ipv6 4448 5261 +813 (+18.28%) 234 247 +13 (+5.56%)
bpf_xdp.o tail_lb_ipv4 71736 73442 +1706 (+2.38%) 4295 4370 +75 (+1.75%)
------------- ------------------------------ --------------- --------------- ------------------ ---------------- ---------------- -------------------
P.S. To make Cilium ([0]) programs libbpf-compatible and thus
veristat-loadable, apply changes from topmost commit in [1], which does
minimal changes to Cilium source code, mostly around SEC() annotations
and BPF map definitions.
[0] https://github.com/cilium/cilium/
[1] https://github.com/anakryiko/cilium/commits/libbpf-friendliness
Fixes: b5dc0163d8 ("bpf: precise scalar_value tracking")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20221104163649.121784-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e38e42c078 ]
devm_pinctrl_get() may return ERR_PTR(-EPROBE_DEFER), add a minus sign
to fix it.
Fixes: 4163851f7b ("[media] s5p-fimc: Use pinctrl API for camera ports configuration")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5e477a861 ]
For the case where allow_ptr_leaks is false, code is checking whether
slot type is STACK_INVALID and STACK_SPILL and rejecting other cases.
This is a consequence of incorrectly checking for register type instead
of the slot type (NOT_INIT and SCALAR_VALUE respectively). Fix the
check.
Fixes: 01f810ace9 ("bpf: Allow variable-offset stack access")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20221103191013.1236066-5-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b964444b2b ]
Use devm_pm_runtime_enable() to enable runtime PM. This way its effect
will be reverted on device unbind/destruction.
Fixes: 6ed9ed484d ("drm/msm/hdmi: Set up runtime PM for HDMI")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499647/
Link: https://lore.kernel.org/r/20220826093927.851597-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e674b13b ]
The HDMI driver has code to configure extra GPIOs, which predates
pinctrl support. Nowadays all platforms should use pinctrl instead.
Neither of upstreamed Qualcomm platforms uses these properties, so it's
safe to drop them.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/488858/
Link: https://lore.kernel.org/r/20220609122350.3157529-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: b964444b2b ("drm/msm/hdmi: use devres helper for runtime PM management")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7423dbdbc ]
IMA relies on the blocking LSM policy notifier callback to update the
LSM based IMA policy rules.
When SELinux update its policies, IMA would be notified and starts
updating all its lsm rules one-by-one. During this time, -ESTALE would
be returned by ima_filter_rule_match() if it is called with a LSM rule
that has not yet been updated. In ima_match_rules(), -ESTALE is not
handled, and the LSM rule is considered a match, causing extra files
to be measured by IMA.
Fix it by re-initializing a temporary rule if -ESTALE is returned by
ima_filter_rule_match(). The origin rule in the rule list would be
updated by the LSM policy notifier callback.
Fixes: b169424551 ("ima: use the lsm policy update notifier")
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf585ccee2 ]
struct spi_master has been renamed to struct spi_controller. Update the
reference in spi.rst to make it clickable again.
Fixes: 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221101173252.1069294-1-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02693e1161 ]
If condition (clkspec.np != pd->dev.of_node) is true, then the driver
ends up in an endless loop, forever, locking up the machine.
Fixes: aad03a66f9 ("clk: renesas: r9a06g032: Add clock domain support")
Reviewed-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/20221028113834.7496-1-marex@denx.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dba27f1a1 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
We fix it by replacing it with the newest pm_runtime_resume_and_get
to keep usage counter balanced.
Fixes: 34cc0aa254 ("drm/rockchip: Add support for Rockchip Soc LVDS")
Fixes: cca1705c3d ("drm/rockchip: lvds: Add PX30 support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922132107.105419-3-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39d3df6b0e ]
The device will respond with a CMD_ERROR_EVENT command, with error_code
KVASER_USB_{LEAF,HYDRA}_ERROR_EVENT_PARAM, if the CMD_SET_BUSPARAMS_REQ
contains invalid bittiming parameters.
However, this command does not contain any channel reference.
To check if the CMD_SET_BUSPARAMS_REQ was successful, redback and compare
the requested bittiming parameters with the device reported parameters.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-12-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90904d3262 ]
When auto-restart is enabled, the kvaser_usb_leaf driver considers
transition from any state >= CAN_STATE_BUS_OFF as a bus-off recovery
event (restart).
However, these events may occur at interface startup time before
kvaser_usb_open() has set the state to CAN_STATE_ERROR_ACTIVE, causing
restarts counter to increase and CAN_ERR_RESTARTED to be sent despite no
actual restart having occurred.
Fix that by making the auto-restart condition checks more strict so that
they only trigger when the interface was actually in the BUS_OFF state.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11249acf8 ]
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 sends a
CMD_CHIP_STATE_EVENT indicating bus-off after stopping the device,
causing a stopped device to appear as CAN_STATE_BUS_OFF instead of
CAN_STATE_STOPPED.
Fix that by not handling error events on stopped devices.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d21f5927a ]
The tested 0bfd:0017 Kvaser Memorator Professional HS/HS FW 2.0.50 and
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 do not seem to send
any unsolicited events when error counters decrease or when the device
transitions from ERROR_PASSIVE to ERROR_ACTIVE (or WARNING).
This causes the interface to e.g. indefinitely stay in the ERROR_PASSIVE
state.
Fix that by asking for chip state (inc. counters) event every 0.5 secs
when error counters are non-zero.
Since there are non-error-counter devices, also always poll in
ERROR_PASSIVE even if the counters show zero.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
