The SCLP base driver defines a new notifier call back for all upper level SCLP
drivers, like the SCLP console, etc. This guarantees that in suspend first the
upper level drivers are suspended and afterwards the SCLP base driver. For
resume it is the other way round. The SCLP base driver itself registers a
new platform device at the platform bus and gets PM notifications via
the dev_pm_ops.
In suspend, the SCLP base driver switches off the receiver and sender mask
This is done in sclp_deactivate(). After suspend all new requests will be
rejected with -EIO and no more interrupts will be received, because the masks
are switched off. For resume the sender and receiver masks are reset in
the sclp_reactivate() function.
When the SCLP console is suspended, all new messages are cached in the
sclp console buffers. In resume, all the cached messages are written to the
console. In addition to that we have an early resume function that removes
the cached messages from the suspend image.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements suspend/hibernation for the vmwatchdog driver. The
pm_notifier_callchain is used to get control on PM events. Since watchdog
operation and suspend cannot work together in a reliable fashion, the open
flag is also used to prevent suspend and open from happening at the same
time.
The watchdog can also be active with no open file descriptor. This patch
adds another flag which is only changed in vmwdt_keep_alive and
vmwdt_disable.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the 3215 console. On suspend
the console buffer is flushed to the 3215 device to have an empty console
buffer. Printks done while the 3215 device is suspended are buffered in
the 64K buffer of the 3215 device. If the buffer is full new messages will
push out the oldest messages to make room for the most recent message.
On resume the buffered messages are printed. If the system panics before
the 3215 device is resumed ccw_device_force_console is used to get the
console working again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If something goes wrong in a suspend / resume cycle a ccw based console
if very likely in the suspended state and cannot print anything.
Introduce ccw_device_force_console to force the wake up of the console
device to be able to print the oops message. The console device drivers
should use this function only if the system paniced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the dasd driver. On suspend
the dasd devices are stopped and removed from the focus of alias
management.
On resume they are reinitialized by rereading the device characteristics
and adding the device to the alias management.
In case the device has gone away during suspend it will caught in the
suspend state with stopped flag set to UNRESUMED. After it appears again
the restore function is called again.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Thanks to Sebastian Ott <sebott@linux.vnet.ibm.com> for fixing a few
typos in my original version of this patch.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: linux390@de.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up s390 drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- claw: impossible condition, simply remove it
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
Don't access the block layer request, get the payload length instead
from the FC job. Simplify access to the zfcp_port, only the d_id is
required, if the port is no longer accessed later. This is possible
when the els_handler does not access the port pointer from the ELS
request.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Provide the ability to do fibre channel requests from the userspace to
our zfcp driver. Patch builds upon extension to the fibre channel
tranport class by James Smart and Seokmann Ju. See here
http://marc.info/?l=linux-scsi&m=123808882309133&w=2
Signed-off-by: Sven Schuetz <sven@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (154 commits)
[SCSI] osd: Remove out-of-tree left overs
[SCSI] libosd: Use REQ_QUIET requests.
[SCSI] osduld: use filp_open() when looking up an osd-device
[SCSI] libosd: Define an osd_dev wrapper to retrieve the request_queue
[SCSI] libosd: osd_req_{read,write} takes a length parameter
[SCSI] libosd: Let _osd_req_finalize_data_integrity receive number of out_bytes
[SCSI] libosd: osd_req_{read,write}_kern new API
[SCSI] libosd: Better printout of OSD target system information
[SCSI] libosd: OSD2r05: Attribute definitions
[SCSI] libosd: OSD2r05: Additional command enums
[SCSI] mpt fusion: fix up doc book comments
[SCSI] mpt fusion: Added support for Broadcast primitives Event handling
[SCSI] mpt fusion: Queue full event handling
[SCSI] mpt fusion: RAID device handling and Dual port Raid support is added
[SCSI] mpt fusion: Put IOC into ready state if it not already in ready state
[SCSI] mpt fusion: Code Cleanup patch
[SCSI] mpt fusion: Rescan SAS topology added
[SCSI] mpt fusion: SAS topology scan changes, expander events
[SCSI] mpt fusion: Firmware event implementation using seperate WorkQueue
[SCSI] mpt fusion: rewrite of ioctl_cmds internal generated function
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Function graph tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a DASD requests is started with dasd_sleep_on and fails, then the
calling function may need to know the reason for the failure.
In cases of hardware errors it can inspect the sense data in the irb,
but when the reason is internal (e.g. start_IO failed) then it needs
a meaningfull return code.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some functions called as a late_initcall depend on completely
initialized devices. Since commit
f3445a1a65 the dasd driver uses the
new async framework and relies on the fact that synchronization is
done in prepare_namespace which is called after the late_initcalls.
Fix this by calling async_synchronize_full at the end of the related
init functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a broken memset (sizeof pointer vs sizeof the underlying
structure) by cleaning up the involved functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The High Performance FICON feature is not supported in 31-bit mode,
no matter what the various flags say. So we need to check for the
CONFIG_64BIT option as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit f331c0296f changed users of
->first_minor to devt. This broke device handling in dcssblk, so that
no additional devices could be added after the first one.
This patch reverts the devt conversion to the previous ->first_minor
handling.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not go beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lockdep found a problem with the lock order of the view lock and the
ccw device lock. raw3270_activate_view/raw3270_deactivate_view first
take the ccw device lock then call the activate/deactivate functions
of the view which take view lock. The update functions of the
con3270/tty3270 view will first take the view lock, then take the
ccw device lock. To fix this the activate/deactivate functions are
changed to avoid taking the view lock by moving the functions calls
that modify the 3270 output buffer to the update function which is
called by a timer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The tty3270_notifier that calls tty_register_device / tty_unregister_device
is harmful in two ways:
1) the device node that is create is wrong because the minor numbers for
3270 tty start with 1 and tty_notifier passes the minor as index.
2) If 1) is corrected you'll get a warning:
WARNING: at fs/sysfs/dir.c:462 sysfs_add_one+0x4c/0x60()
sysfs: duplicate filename '227:1' can not be created
The 227:1 link is already created by raw3270_create_attributes to refer
to ../../class/tty/tty<devno>. There cannot be two links.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move qdio_perf_stat_inc to the header file so it can be inlined.
Remove unused qdio_perf_stat_dec.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check for the device status in qdio_establish_handle_irq()
had dead code. Remove the unused code and simplify the error
handling.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some sanity checks in device_ops.c test the output of container_of
macros to be !NULL. Test the input parameters instead.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All definition in cpu.h have to do with cputime accounting. Move
them to cputime.h and remove the header file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the information about the device and model id in zfcp_ccw. This
requires an additional helper function to check for the privileged
cfdc subchannel, but it allows the removal of the redundant defines
from the zfcp_def header file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the destination ID (D_ID) of a remote storage port changed, e.g.
re-plugged cable on the switch in a different switch port, the port
was never (re-)attached within Linux. This patch fixes the broken
mapping between the WWPN and the D_ID.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In rare cases, open port request might timeout, erp calls
zfcp_port_put, port gets dequeued. Now, the late returning (or
dismissed) fsf-port-open calls the fsf_port_open_handler that tries to
reference the port data structure leading to a kernel oops.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add comments where there is a deliberate fall through in switch/case
statements. This makes some code checkers happy and makes it clear
that there is no missing break statement.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
enum dma_data_direction only has the 4 values DMA_BIDIRECTIONAL,
DMA_TO_DEVICE, DMA_FROM_DEVICE and DMA_NONE. No need to have the
default case. While changing this, setup sbtype in one place to make
sparse happy.
The default value of retval is already -EIO, so remove the
additional assignment for these two cases.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp did always set the queue_depth for SCSI devices to 32, not
allowing to change this. Introduce a kernel parameter zfcp.queue_depth
and the change_queue_depth callback to allow changing the queue_depth
when it is required.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update the newly introduced message for the boxed status to conform to
match the style of s390 and zfcp messages.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The zfcp traces used the fsf_req address in place of the req_id.
Change this to save the correct req_id.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Function qeth_clear_output_buffer for HiperSockets may not clear
all 16 SBALEs, but only the used ones. The error flag in SBALF15
has to be cleared in any case.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSocket devices receive-path checksumming is not required.
Thus NO_CHECKSUMMING is used as default for HiperSocket interfaces.
For layer3 devices configured with NO_CHECKSUMMING received skbs
should have set their ip_summed field to CHECKSUM_UNNECESSARY.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/VM Virtual Switch Port Isolation allows guests on a VLAN UNAWARE
virtual switch to be isolated from other guests on the VSWITCH.
(See z/VM Apars VM64281 and VM64463).
The Linux qeth driver is affected, because it has to handle new
error codes introduced with the z/VM VSWITCH Port Isolation support.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels are already removed when setting a ctcm-device offline.
Thus ctcm_remove_device must not refer to channel information.
Solution: delete channel information from the trace call in
ctcm_remove_device.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qeth device is plugged off, setting the device online stops in
state HARDSETUP and a failure is reported to the base cio-layer
causing halt/clear to be invoked. Replugging the device again triggers
a qeth recovery without notification of the cio-layer. If a device
is ungrouped in this state, the qeth set_offline function is not
invoked, because the corresponding ccwgroup device is not in state
ONLINE. Then incoming traffic is still handled by the qdio layer
resulting in a crash in qeth_l<x>_qdio_input_handler, because (part
of) the qeth data structures for this device are already removed.
Solution: After replugging the device qeth recovery should lead to a
working net device. Thus a "LAN offline" result when setting a qeth
device online must not report a failure to the base cio-layer.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion. Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.
This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request. BUG_ON() is added to to ensure that
this actually happens.
Most conversions are simple but there are a few noteworthy ones.
* cdrom/viocd: viocd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/block/dasd: dasd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/char/tape_block: tapeblock_end_request() replaced with direct
calls to blk_end_request_all().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
The zfcp_port might have been removed, while the FC fast_io_fail timer
is still running and could trigger the terminate_rport_io callback.
Set the pointer to the zfcp_port to NULL and check accordingly
before using it.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Before dropping the reference count with zfcp_adapter_put, increase it
with zfcp_adapter_get when issuing cfdc requests.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If this problem appears zfcp ports cannot be de-queued since it is
checked for a zero refcount. The port reference counting is wrong for
existing zfcp ports when e.g. an adapter gets on-line again. During
port scanning the reference counting for existing ports should not be
changed.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current sbal counting can be wrong if a fsf request is
waiting for free sbals and at the same time qdio request queue
is shutdown and re-opened. Revering a previous patch fixes this
issue.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the abort handler cannot find a pending FSF request, the request
completion could just be running. This means we cannot return SUCCESS,
since this would lead to call to scsi_done after exiting the SCSI
error handler which is not allowed.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A remote port remains in error state even if we receive a RSCN
stating that the connection is re-established. The port recovery
is not started due to a flag which is not reset.
The solution is to clear the flag in question before we trigger a ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Error codes specific to the control file requests are evaluated by the
actcli tool, so don't report -ENXIO for those. Generic problems are
still checked for outside the command specific handler.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On some hardware it can take some time to add a unit. If
some remove this unit during this process the remove will
fail.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The remote port remains in error state even if the connection
is re-established. A wrong precondition check was performed on
the port status leading to a cancellation of the port reopen.
Remove the pre-req check because it's not required and better
handled within the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ERP thread is performing a task before it is executing the
corresponding down on the semaphore. The response handler of the
just started exchange config should wait for the completion by
performing a down on this semaphore. Since this semaphore is still
positive from the ERP enqueue the handler won't wait and therefore
the exchange config will always fail leaving the adapter in error.
The problem can be solved by performing the down on the semaphore
before starting an ERP task. This is the logically correct order.
Only walk the ERP loop if there is a task to perform.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The nameserver port might be in state online when the adapter is
offlined. On adapter reactivation the nameserver port is not
re-opened due to the PORT_ONLINE status. This results in an
unsuccessful recovery. In forcing the nameserver port status
to offline on all adapter offline events this issue is prevented.
Waiting for the reference count to drop to zero in
zfcp_wka_port_offline is not required, so remove it.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When running the scsi_scan from the zfcp workqueue and the target
device does not respond, the zfcp workqueue can block until the
scsi_scan hits a timeout. Move the work to the scsi host workqueue,
since this one is also used for the scan from the SCSI midlayer.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix problem that zfcp_fsf_exchange_config_data_sync and
zfcp_fsf_exchange_config_data_sync could try to call zfcp_fsf_req_free
with a NULL pointer.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since we're setting the host port type now to FC_PORTTYPE_NPIV
for adapters running in NPIV mode we should allow this port type
for auto-port scanning as well.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Avoid referencing a fsf request after sending it in fcp_fsf_req_send,
it might have already completed and deallocated.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
tape_3590_offline and tape_34xx_offline are removed and tape_generic_offline
is called directly instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A ccw command that reads or writes several records at once will
usually transfer more data then fits into one page and needs to
address memory areas using a list of indirect data address words
(idaw). All but the first of these areas must start on a 4KB or 2KB
block boundary (depending on the idaw format).
A check for this restriction was missing and has been added with
this patch.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd driver can automatically online detected dasds, which
especially important for finding the root device. Currently,
it will wait for each online operation to finish individually,
which may take long if many dasds need to be onlined. When using
the new async framework, these onlining operations can run in
parallel and presence of the root device is ensured by the fact
that prepare_namespace() waits for all async threads to finish.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The QDIO ccw devices are started by ccw_device_start so no timeout
can occur for the interrupt handler. Remove the dead code.
In case of an I/O error set the device state to error and wake up
a possibly running qdio_shutdown waiter.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 64ef895798 ("qeth: remove EDDP")
removed the qeth_core_offl.[hc] files, but ended up doing so by just
patching them to zero size, rather than removing them properly.
Actually remove the files.
Reported-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start a new device recognition if someone writes to sysfs online attribute
of a boxed ccw device. The current test will fail, since cu_type != 0
for devices which were recognized before.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Return -EAGAIN on writes to sysfs online attribute if the corresponding
ccw device is in transient state.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a ccw device did not respond in time during internal io, we set it
into boxed state. With this patch we have the following behaviour:
* the ccw driver will get a notification if the device was online and
goes into the boxed state
* if the device was disconnected and got boxed nothing special is to be
done (it will be handled in reprobing later)
* if the device got boxed while initial sensing it will be unregistered
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce ccw_device_schedule_sch_unregister as a wrapper for queuing
ccw_device_call_sch_unregister on the slow_path_wq. This wrapper
will be used in the next patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Wake up even on failed device recognition, since this may be triggered
from a user trying to force a device online. With this patch a write
to the online sysfs attribute will not block for ever but return with
-EAGAIN in this case.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (81 commits)
[S390] remove duplicated #includes
[S390] cpumask: use mm_cpumask() wrapper
[S390] cpumask: Use accessors code.
[S390] cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.
[S390] cpumask: remove cpu_coregroup_map
[S390] fix clock comparator save area usage
[S390] Add hwcap flag for the etf3 enhancement facility
[S390] Ensure that ipl panic notifier is called late.
[S390] fix dfp elf hwcap/facility bit detection
[S390] smp: perform initial cpu reset before starting a cpu
[S390] smp: fix memory leak on __cpu_up
[S390] ipl: Improve checking logic and remove switch defaults.
[S390] s390dbf: Remove needless check for NULL pointer.
[S390] s390dbf: Remove redundant initilizations.
[S390] use kzfree()
[S390] BUG to BUG_ON changes
[S390] zfcpdump: Prevent zcore from beeing built as a kernel module.
[S390] Use csum_partial in checksum.h
[S390] cleanup lowcore.h
[S390] eliminate ipl_device from lowcore
...
Use kzfree() instead of memset() + kfree().
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cksm function in system.h is duplicate to csum_partial in checksum.h.
Remove cksm and use csum_partial instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
