This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use X86_FEATURE_NOPL to determine if it is safe to use P6 NOPs in
alternatives. Also, replace table and loop with simple if statement.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The long noops ("NOPL") are supposed to be detected by family >= 6.
Unfortunately, several non-Intel x86 implementations, both hardware
and software, don't obey this dictum. Instead, probe for NOPL
directly by executing a NOPL instruction and see if we get #UD.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CPU feature detection code in the boot code is somewhat minimal,
and doesn't include all possible CPUID words. In particular, it
doesn't contain the code for CPU feature words 2 (Transmeta),
3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we
can still set those bits as known at compile time; in particular, this
allows creating a Linux-specific NOPL flag and have it required (and
therefore resolvable at compile time) in 64-bit mode.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* git://git.infradead.org/~dwmw2/dwmw2-2.6.27:
Revert "[ARM] use the new byteorder headers"
Fix conditional export of kvh.h and a.out.h to userspace.
[MTD] [NAND] tmio_nand: fix base address programming
Currently init_initrd() probes initrd header at the last page of kernel
image, but it is valid only if addinitrd was used. If addinitrd was not
used, the area contains garbage so probing there might misdetect initrd
header (magic number is not strictly robust).
This patch introduces CONFIG_PROBE_INITRD_HEADER to explicitly enable this
probing.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The txx9_pcode variable was introduced in commit
fe1c2bc64f65003b39f331a8e4b0d15b235a4afd ("TXx9: Add 64-bit support")
but was not initialized properly.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trap_init issues flush_icache_range(), which uses ipi functions to
get icache flushing done on all cpus. But this is done before interrupts
are enabled and caused WARN_ON messages. This changeset introduces
a new local_flush_icache_range() and uses it before interrupts (and
additional CPUs) are enabled to avoid this problem.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With -ffunction-section the entries in __dbe_table aren't no longer
sorted, so the lookup of exception addresses in do_be() failed for
some addresses. To avoid this we now sort __dbe_table.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit ae82cbfc8b. It
needs the new byteorder headers to be exported to userspace, and
they aren't yet -- and probably shouldn't be, at this point in the
2.6.27 release cycle (or ever, for that matter).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The minimum reprogramming delta was hardcoded in HPET ticks,
which is stupid as it does not work with faster running HPETs.
The C1E idle patches made this prominent on AMD/RS690 chipsets,
where the HPET runs with 25MHz. Set it to 5us which seems to be
a reasonable value and fixes the problems on the bug reporters
machines. We have a further sanity check now in the clock events,
which increases the delta when it is not sufficient.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Tested-by: Dmitry Nezhevenko <dion@inhex.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a problem within the SH implementation of resume_kernel code,
that implements in assembly the bulk of preempt_schedule_irq function without
taking care of the extra code needed to handle the BKL preemptible.
The patch basically consists of removing this asm code and calling the common
C implementation (see kernel/sched.c) as other archs do.
Another change is the missing 'cli' macro invocation at the beginning of
the resume_kernel.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We currently have a race for a free SPE. With one thread doing a
spu_yield(), and another doing a spu_activate():
thread 1 thread 2
spu_yield(oldctx) spu_activate(ctx)
__spu_deactivate(oldctx)
spu_unschedule(oldctx, spu)
spu->alloc_state = SPU_FREE
spu = spu_get_idle(ctx)
- searches for a SPE in
state SPU_FREE, gets
the context just
freed by thread 1
spu_schedule(ctx, spu)
spu->alloc_state = SPU_USED
spu_schedule(newctx, spu)
- assumes spu is still free
- tries to schedule context on
already-used spu
This change introduces a 'free_spu' flag to spu_unschedule, to indicate
whether or not the function should free the spu after descheduling the
context. We only set this flag if we're not going to re-schedule
another context on this SPU.
Add a comment to document this behaviour.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Commit 8d5636fbca introduced a reference
count on SPU contexts during find_victim, but this may cause a leak in
the reference count if we later find a better contender for a context to
unschedule.
Change the reference to after we've found our victim context, so we
don't do the extra get_spu_context().
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
mcbsp is confused as to what takes a physical or virtual address.
Fix the two instances where it gets it wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
arch/arm/plat-mxc/clock.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When calibration against PIT fails, the warning that we print is misleading.
In a virtualized environment the VM may get descheduled while calibration
or, the check in PIT calibration may fail due to other virtualization
overheads.
The warning message explicitly assumes that calibration failed due to SMI's
which may not be the case. Change that to something proper.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix for getting CPU number in power_save_ppc32_restore()
powerpc: Fix build error with 64K pages and !hugetlbfs
powerpc: Work around gcc's -fno-omit-frame-pointer bug
powerpc: Make sure _etext is after all kernel text
powerpc: Only make kernel text pages of linear mapping executable
powerpc: Fix uninitialised variable in VSX alignment code
Manually adding "io_delay=0xed" fixes system lockups in ioapic
mode on this machine.
System Information
Manufacturer: Hewlett-Packard
Product Name: Presario F700 (KA695EA#ABF)
Base Board Information
Manufacturer: Quanta
Product Name: 30D3
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=459546
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The TSC calibration function is still very complicated, but this makes
it at least a little bit less so by moving the PIT part out into a
helper function of its own.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
The calculation to get TI_CPU based off of SPRG3 was just plain wrong,
meaning that we were getting garbage for the CPU number on 6xx/G3/G4
based SMP boxes in this code.
Just offset off the stack pointer (to get to thread_info) like all the
other references to TI_CPU do.
This was pointed out by Chen Gong <G.Chen@freescale.com>
[paulus@samba.org - use rlwinm r12,r11,... instead of
rlwinm r12,r1,...; tophys()]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
HAVE_ARCH_UNMAPPED_AREA and HAVE_ARCH_UNMAPPED_AREA_TOPDOWN must
be defined whenever CONFIG_PPC_MM_SLICES is enabled, not just when
CONFIG_HUGETLB_PAGE is. They used to be always defined together but
this is no longer the case since 3a8247cc2c
("powerpc: Only demote individual slices rather than whole process").
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This bug is causing random crashes
(http://bugzilla.kernel.org/show_bug.cgi?id=11414).
-fno-omit-frame-pointer is only needed on powerpc when -pg is also
supplied, and there is a gcc bug that causes incorrect code generation
on 32-bit powerpc when -fno-omit-frame-pointer is used---it uses stack
locations below the stack pointer, which is not allowed by the ABI
because those locations can and sometimes do get corrupted by an
interrupt.
This ensures that CONFIG_FRAME_POINTER is only selected by ftrace.
When CONFIG_FTRACE is enabled we also pass -mno-sched-epilog to work
around the gcc codegen bug.
Patch based on work by:
Andreas Schwab <schwab@suse.de>
Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes core_kernel_text() (and therefore kernel_text_address())
return the correct result. Currently all the __devinit routines (at
least) will not be considered to be kernel text.
This is just a quick fix for 2.6.27 - hopefully we will be able to fix
this better in 2.6.28.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit bc033b63bb ("powerpc/mm: Fix
attribute confusion with htab_bolt_mapping()") moved the check for
whether we should make pages of the linear mapping executable from
htab_bolt_mapping into its callers, including htab_initialize.
A side-effect of this is that the decision is now made once for
each contiguous section in the LMB array rather than for each page
individually. This can often mean that the whole of the linear
mapping ends up being executable.
This reverts to the previous behaviour, where individual pages are
checked for being part of the kernel text or not, by moving the check
back down into htab_bolt_mapping.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes an uninitialised variable in the VSX alignment code. It can
cause warnings from GCC (noticed with gcc-4.1.1). Gcc is actually
correct in this instance, and this bug could cause the alignment
interrupt handler to send a SIGSEGV to the process on a legitimate
access.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make sparc64 refrain from clearing a given to-be-offlined CPU's bit in the
cpu_online_mask until it has processed pending irqs. This change
prevents other CPUs from being blindsided by an apparently offline CPU
nevertheless changing globally visible state.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/arm/plat-omap/gpio.c: In function '_omap_gpio_init':
arch/arm/plat-omap/gpio.c:1492: error: 'omap_mpuio_device' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When I switched sparc64 over to the generic helpers for
smp_call_function(), I didn't convert the dinky call_lock
we had.
Use ipi_call_lock() and ipi_call_unlock().
Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger reported at http://lkml.org/lkml/2008/9/1/90:
An ancient laptop of mine started throwing errors from b43legacy when
I started using 2.6.27 on it. This has been bisected to commit bfc0f59
"x86: merge tsc calibration".
The unification of the TSC code adopted mostly the 64bit code, which
prefers PMTIMER/HPET over the PIT calibration.
Larrys system has an AMD K6 CPU. Such systems are known to have
PMTIMER incarnations which run at double speed. This results in a
miscalibration of the TSC by factor 0.5. So the resulting calibrated
CPU/TSC speed is half of the real CPU speed, which means that the TSC
based delay loop will run half the time it should run. That might
explain why the b43legacy driver went berserk.
On the other hand we know about systems, where the PIT based
calibration results in random crap due to heavy SMI/SMM
disturbance. On those systems the PMTIMER/HPET based calibration logic
with SMI detection shows better results.
According to Alok also virtualized systems suffer from the PIT
calibration method.
The solution is to use a more wreckage aware aproach than the current
either/or decision.
1) reimplement the retry loop which was dropped from the 32bit code
during the merge. It repeats the calibration and selects the lowest
frequency value as this is probably the closest estimate to the real
frequency
2) Monitor the delta of the TSC values in the delay loop which waits
for the PIT counter to reach zero. If the maximum value is
significantly different from the minimum, then we have a pretty safe
indicator that the loop was disturbed by an SMI.
3) keep the pmtimer/hpet reference as a backup solution for systems
where the SMI disturbance is a permanent point of failure for PIT
based calibration
4) do the loop iteration for both methods, record the lowest value and
decide after all iterations finished.
5) Set a clear preference to PIT based calibration when the result
makes sense.
The implementation does the reference calibration based on
HPET/PMTIMER around the delay, which is necessary for the PIT anyway,
but keeps separate TSC values to ensure the "independency" of the
resulting calibration values.
Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6
(affected machine with a double speed pmtimer which I grabbed out of
the dump), Pentium class machines and AMD/Intel 64 bit boxen.
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix operator precedence bug in atari_keyb_init, which caused a failure on CT60
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A parisc allmodconfig build produces this:
arch/parisc/hpux/fs.c:107: error: 'buffer' undeclared (first use in this function)
Introduced by commit da574983de ("[PATCH]
fix hpux_getdents()").
Helge Dille also reported this in bugzilla 11461:
http://bugzilla.kernel.org/show_bug.cgi?id=11461
and he posted an identical patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: setup_valid_addr_bitmap_from_pavail() should be __init
sparc: Fix resource flags for PCI children in OF device tree.
sparc32: Implement smp_call_function_single().
Breaking lines due to some imaginary problem with a long line length is
often stupid and wrong, but never more so when it splits a string that
is printed out into multiple lines. This really ended up making it much
harder to find where some error strings were printed out, because a
simple 'grep' didn't work.
I'm sure there is tons more of this particular idiocy hiding in other
places, but this particular case hit me once more last week. So fix it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The value stored into the SDRAMC LPR register should be the current
value of the register with the Self-refresh value set in the lower bit
field.
The bug involved only the Self-refresh value being written to the
register, thus over writing any low-power ram settings.
Signed-off-by: Humphrey Bucknell <hbucknell@saitek.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
When using the Java Extension Module hardware, a Java stack underflow or
overflow trap may cause the system to enter an infinite exception loop.
Although there's no kernel support for the Java hardware yet, we need to
be able to recover from this situation and keep the system running.
This patch adds code to detect and fixup this situation in the critical
exception handler and terminate the faulting process. We may have to
rethink how to handle this more gracefully when the necessary kernel
support for hardware-accelerated Java is added.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This reverts commit a2bd7274b4.
It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.
Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a device is under an EBUS or ISA bus, the resource flags
don't get set properly.
Fix this by re-evaluating the resource flags at each level of
bus as we apply ranges on the way to the root. And let PCI
override any existing flags setting, but don't let the
default flags calculator make such overrides.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
Blackfin arch: sram: use 'unsigned long' for irqflags
Blackfin arch: let PCI depend on BROKEN
Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Blackfin arch: fix bug - MPU crashes under stress
Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK
Using just 'unsigned' will make flags an unsigned int. While this is
arguably not an error on blackfin where sizeof(int) == sizeof(long),
the patch is still justified on the grounds of principle.
The patch was generated using the Coccinelle semantic patch framework.
Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
fix the problem that cannot work semtimedop system call.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the AP325RXA defconfig to include the recently merged
uio_pdrv_genirq driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the MigoR defconfig to include the recently merged
uio_pdrv_genirq driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch kills a section mismatch for platform_resource_setup_memory().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The crash kernel entry point is currently checked by the kexec kernel
code and only physical addresses in the reserved memory window are
accepted. This means that we can't pass P2 or P1 addresses as entry
points in the case of crash kernels. This patch makes sure we can start
crash kernels by adding support for physical address entry points.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The reserved crash kernel memory range is currently missing from
/proc/iomem. crashk_res is mistakenly setup after __add_active_range().
Reorder things to make sure the resource shows up in /proc/iomem.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] deal with the first call of ->show() generating no output
[PATCH] fix ->llseek() for a bunch of directories
[PATCH] fix regular readdir() and friends
[PATCH] fix hpux_getdents()
[PATCH] fix osf_getdirents()
[PATCH] ntfs: use d_add_ci
[PATCH] change d_add_ci argument ordering
[PATCH] fix efs_lookup()
[PATCH] proc: inode number fixlet
Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.
This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone. Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes arm to use the new bcd2bin/bin2bcd functions instead
of the obsolete BCD_TO_BIN/BIN_TO_BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Taken from omap 97b705ad835f1481270c4b67b402d6e37fa8ad15:
ARM: OMAP: Misc compile fixes after syncing with mainline
Also fix 2430 smc91x to use IRQ_LOWLEVEL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable some option commonly used by testers in defconfig, including
some very common device drivers and network boot support. defconfig
is still not meant to be a kitchen-sink configuration.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
AFAIR there exists blackfin hardware with PCI support, but the support
currently in the kernel fails to build starting with:
...
CC drivers/pci/probe.o
probe.c: In function 'pci_scan_slot':
probe.c:1056: error: implicit declaration of function 'pcibios_scan_all_fns'
make[3]: *** [drivers/pci/probe.o] Error 1
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Fix the S3C2443 clock register definitions for selecting the EPLL
reference clock described by S3C2443_CLKSRC_EPLLREF.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
[ben-linux@fluff.org: minor description fixes]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The first spi bus is registered with number 0, but
the board data says that the device on it is registered
on bus 1.
Move the spi bus to bus 1 to keep the compatibility with the
original board-support patches.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm.c:
warning: symbol 's3c_device_timer' was not declared. Should it be static?
warning: symbol 'pwm_calc_tin' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/plat-s3c24xx/pwm-clock.c:
warning: symbol 'clk_timer_scaler' was not declared. Should it be static?
warning: symbol 'clk_timer_tclk' was not declared. Should it be static?
warning: symbol 'clk_timer_tdiv' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following problems spotted by sparse:
warning: symbol 's3c24xx_gpiolib_input' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_output' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_set' was not declared. Should it be static?
warning: symbol 's3c24xx_gpiolib_get' was not declared. Should it be static?
warning: symbol 'gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse errors in arch/arm/mach-s3c2410/nor-simtec.c:
53:27: warning: symbol 'simtec_nor_pdata' was not declared. Should it be static?
77:13: warning: symbol 'nor_simtec_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Fix __{in,out}s{w,l} to handle unaligned data
[IA64] Fix ia64 build failure when CONFIG_SFC=m
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Ignore vmlinux.lds generated files
[MIPS] kgdb: Do not call fixup_exception
[MIPS] RB532: Do not define registers that are already defined
[MIPS] IP27: Export symbol pcibus_to_node to modules.
[MIPS] kgdb: s/(void *)0)/NULL/
[MIPS] kgdb: smp_call_function's 3rd argument is a pointer.
[MIPS] TXx9: Fix mips_hpt_frequency initialization
[MIPS] emma2rh: Fix build error by header file inclusion weeding.
[MIPS] Jazz: Fix build error by header file inclusion weeding.
[MIPS] Wire up new syscalls.
[MIPS] Convert printk statements during kernel setup to use severity levels
corgi, spitz and poodle have audio codecs on their primary I2C bus so
need to call pxa_set_i2c_info() to set it up during init. Tested on
spitz by Stanislav.
Reported-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
kgdb_mips_notify is called on IBE/DBE/FPE/BP/TRAP/RI exception. None
of them need fixup. And doing fixup for a breakpoint exception will
confuse gdb.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the register definitions of the MPMC controller from
mach-rc32434/rb.h instead of redefining them.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/emma2rh/markeins/setup.o
In file included from arch/mips/emma2rh/markeins/setup.c:30:
include/linux/ide.h:645: error: ‘CONFIG_IDE_MAX_HWIFS’ undeclared here (not in a function)
make[1]: *** [arch/mips/emma2rh/markeins/setup.o] Error 1
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Return the correct return value when the CPUID driver partially
completes a request (we should return the number of bytes actually
read or written, instead of the error code.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Return the correct return value when the MSR driver partially
completes a request (we should return the number of bytes actually
read or written, instead of the error code.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
