Sudarsana Reddy Kalluru says:
====================
qed*: PTP bug fixes.
The series addresses couple of issues in the PTP implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Tx timestamping data structures are not protected against the
concurrent access in the Tx paths. Protecting the same using atomic
bit locks.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IOT2000 is industrial controller platform, derived from the Intel
Galileo Gen2 board. The variant IOT2020 comes with one LAN port, the
IOT2040 has two of them. They can be told apart based on the board asset
tag in the DMI table.
Based on patch by Sascha Weisenberger.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be careful when comparing tcp_time_stamp to some u32 quantity,
otherwise result can be surprising.
Fixes: 7c106d7e78 ("[TCP]: TCP Low Priority congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I say:
====================
Fix some bpf program testing framework bugs
This series fixes two issue:
1) Accidental user pointer dereference in bpf_test_finish()
2) The packet data given to the test programs is not aligned correctly
The first issue is fixed simply because we have a kernel side copy
of the datastructure in question already. And the second bug is
a simple matter of applying NET_IP_ALIGN where needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we apply NET_IP_ALIGN when reserving headroom for SKB
and XDP test runs, just like a real driver would.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Instead, pass the kattr in which has a kernel side copy of this
data structure from userspace already.
Fix based upon a suggestion from Alexei Starovoitov.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Fix kdoc parameter spelling from extact to extack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings triggered by 51570a5ab2 ("A Sample of
using socket cookie and uid for traffic monitoring"):
In file included from /home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:54:0:
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c: In function 'prog_load':
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:119:27: warning: overflow in implicit constant conversion [-Woverflow]
-32 + offsetof(struct stats, uid)),
^
/home/foo/net-next/samples/bpf/libbpf.h:135:12: note: in definition of macro 'BPF_STX_MEM'
.off = OFF, \
^
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:121:27: warning: overflow in implicit constant conversion [-Woverflow]
-32 + offsetof(struct stats, packets), 1),
^
/home/foo/net-next/samples/bpf/libbpf.h:155:12: note: in definition of macro 'BPF_ST_MEM'
.off = OFF, \
^
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:129:27: warning: overflow in implicit constant conversion [-Woverflow]
-32 + offsetof(struct stats, bytes)),
^
/home/foo/net-next/samples/bpf/libbpf.h:135:12: note: in definition of macro 'BPF_STX_MEM'
.off = OFF, \
^
HOSTLD /home/foo/net-next/samples/bpf/per_socket_stats_example
Fixes: 51570a5ab2 ("A Sample of using socket cookie and uid for traffic monitoring")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other JITs, sparc64 maintains an array of instruction offsets but
stores the entries off by one. This is done because jumps to the
exit block are indexed to one past the last BPF instruction.
So if we size the array by the program length, we need to record
the previous instruction in order to stay within the array bounds.
This is explained in ARM JIT commit 8eee539dde ("arm64: bpf: fix
out-of-bounds read in bpf2a64_offset()").
But this scheme requires a little bit of careful handling when
the instruction before the branch destination is a 64-bit load
immediate. It takes up 2 BPF instruction slots.
Therefore, we have to fill in the array entry for the second
half of the 64-bit load immediate instruction rather than for
the one for the beginning of that instruction.
Fixes: 7a12b5031c ("sparc64: Add eBPF JIT.")
Signed-off-by: David S. Miller <davem@davemloft.net>
By using smaller datatypes this (rather large) struct shrinks considerably
(80 -> 48 bytes on x86_64).
As this is embedded in other structs, this also rerduces size of several
others, e.g. cls_fl_head or nft_hash.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not want to include things like stdio.h and friends into
eBPF program builds. bpf_util.h is for host compiled programs,
so eBPF C-code helpers don't really belong there.
Add a new bpf_endian.h as a quick fix for this for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since that change also made the nfrag function not necessary
for exports, remove it.
Fixes: 89a23c8b52 ("ip6_tunnel: Fix missing tunnel encapsulation limit option")
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: 802.1s and 88E6390 VTU
This patch series adds support for the VLAN Table Unit (a.k.a. the VTU)
to the 88E6390 family of Marvell Ethernet switch chips. The plumbing for
the per VLAN Spanning Tree support is added as a side effect of the
necessary refactoring.
The patchset is split up so that no duplication of code is introduced.
With this patchset applied, the mv88e6xxx driver has 2 new function
pointers for the VTU GetNext and VTU Load/Purge operations (with 3
implementations), both handling programmation of 802.1q and 802.1s.
On a ZII Rev C board (featuring 2 88E6390X chips) with all ports bridged
together, we obtain the following hardware VLAN configuration:
# cat /sys/class/net/br0/bridge/vlan_filtering
1
# cat /sys/class/net/br0/bridge/default_pvid
42
# bridge vlan add dev lan3 vid 666
# bridge vlan show
port vlan ids
lan1 42 PVID Egress Untagged
lan1 42 PVID Egress Untagged
lan2 42 PVID Egress Untagged
lan2 42 PVID Egress Untagged
lan3 42 PVID Egress Untagged
666
lan3 42 PVID Egress Untagged
666
lan4 42 PVID Egress Untagged
lan4 42 PVID Egress Untagged
lan5 42 PVID Egress Untagged
lan5 42 PVID Egress Untagged
lan6 42 PVID Egress Untagged
lan6 42 PVID Egress Untagged
lan7 42 PVID Egress Untagged
lan7 42 PVID Egress Untagged
lan8 42 PVID Egress Untagged
lan8 42 PVID Egress Untagged
br0 42 PVID Egress Untagged
Below are the technical details for the different implementations.
All switch families have up to 3 dedicated VTU Data registers used to
program 802.1q and 802.1s, both using 2-bit values.
On 88E6185 and 88E6352 families, port membership and state are adjacent,
while the 88E6390 family share the same bits:
Bits 88E6185/88E6352 88E6390
----- ----------------- --------------------------
0-1 Port 0 membership Port 0 membership or state
2-3 Port 0 state Port 1 membership or state
4-5 Port 1 membership Port 2 membership or state
6-7 Port 1 state Port 3 membership or state
8-9 Port 2 membership Port 4 membership or state
10-11 Port 2 state Port 5 membership or state
... ... ...
The 88E6185 family programs all ports membership and state in a single
VTU GetNext or Load/Purge operation.
The 88E6352 family introduced an indirect Spanning Tree Unit table
(a.k.a. STU) which requires additional STU GetNext and Load/Purge
operations to read and write the ports state bits.
The 88E6390 family also has an STU and requires data bits to be accessed
before and after every single VTU or STU operation.
Finally, the 88E6390 family introduced a 13th bit for the VLAN ID, which
must be taken care of regardless the VTU operating mode. This means that
iterating over the VTU now starts or ends with value 8191, not 4095.
Patch 1 adds a max_vid field to the chip info structure.
Patch 2 adds 802.1q and 802.1s data to the generic VTU entry structure.
Patches 3 to 10 move helpers to a dedicated file (later made static).
Patches 11 and 12 abstract handling of the STU behind VTU operations.
Patches 13 and 14 add the new function pointers for VTU operations.
Patches 15 and 18 polish the VTU code and add VTU support for 88E6390.
Changes in v2:
- add Reviewed-by tags
- fix comments in 8/18
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family of chips use only 2 of the 3 VTU Data registers to pack
the MemberTag and PortState VLAN data. This means that they must be
written or read before or after each VTU/STU operations.
Implement this variant to add support for VTU with such chips. These
chips have a 13th bit for the VID thus set their max_vid to 8191.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips such as the 88E6390 have a VTU Page bit in the VTU VID
register to specify a 13th bit for the VID. This can be used to support
8K VLANs.
When dumping the whole VTU, all VID bits must be set to one, including
this VTU Page bit. Add support for VID greater than 4095.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code which fetches or initializes a new VTU entry more concise.
This allows us the get rid of the old underscore prefix naming.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have chip operations for VTU accesses, mark all helpers from
global1_vtu.c as static. Only the various implementations of the
GetNext, LoadPurge and Flush operations need to be exposed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vtu_loadpurge operation to the chip info structure to differ
the various implementations of the VTU accesses.
Now that the STU handling is abstracted behind VTU operations, kill the
obsolete MV88E6XXX_FLAG_STU flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vtu_getnext operation to the chip info structure to differ the
various implementations of the VTU accesses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code writes both VTU and STU data when loading a VTU entry,
load the corresponding STU entry at the same time.
This allows us to get rid of the STU management in the
_mv88e6xxx_vtu_new helper and thus remove the separate implementations
of STU Load/Purge and STU GetNext, as well as the unused family checks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code reads both VTU and STU data on VTU GetNext operation,
fetch the STU entry data of a VTU entry at the same time.
The STU data bits are masked with the VTU data bits and they are now all
read at the same time a VTU GetNext operation is issued.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the generic portion of code to issue an STU GetNext operation,
which will be used in other implementations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to access the VTU Data registers currently only supports the
88E6185 family and alike: 2-bit membership adjacent to 2-bit port state.
Even though the 88E6352 family introduced an indirect table to program
the VLAN Spanning Tree states, the usage of the VTU Data registers
remains the same regardless the VTU or STU operation.
Now that the mv88e6xxx_vtu_entry structure contains both port membership
and states data, factorize the code to access them in global1_vtu.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though every switch model has a different way to access the VTU
Data bits, the base implementation of the VTU GetNext operation remains
the same: wait, write the first VID to iterate from, start the
operation, and read the next VID.
Move this generic implementation into global1_vtu.c and abstract the
handling of the start VID (similarly to the ATU GetNext implementation),
before introducing a new chip operation for specific chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU VID register in the global1_vtu.c file.
At the same time, move mv88e6xxx_g1_vtu_vid_write at the beginning of
_mv88e6xxx_vtu_loadpurge, which adds no functional changes but makes
future patches simpler.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU SID register in the global1_vtu.c file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU FID register in the global1_vtu.c file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the VTU flush operation to global1_vtu.c and call it from a
mv88e6xxx_vtu_setup helper, similarly to the ATU and PVT setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the helper functions to access the Global 1 VTU Operation register
to a new global1_vtu.c file, and get rid of the old underscore prefix
naming convention. This file will be extended will all VTU/STU related
code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN aware Marvell chips can program 802.1Q VLAN membership as well as
802.1s per VLAN Spanning Tree state using the same 3 VTU Data registers.
Some chips such as 88E6185 use different Data registers offsets for
ports state and membership, and program them in a single operation.
Other chips such as 88E6352 use the same register layout but program
them in distinct operations (an indirect table is used for 802.1s.)
Newer chips such as 88E6390 use the same offsets for both state and
membership in distinct operations, thus require multiple data accesses.
To correctly abstract this, split the "data" structure member of
mv88e6xxx_vtu_entry in two "state" and "member" members, before adding
VTU support for newer chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips don't have a VLAN Table Unit, most of them do have a 4K
table, some others as the 88E6390 family has a 13th bit for the VID.
Add a new max_vid member to the info structure, used to check the
presence of a VTU as well as the value used to iterate from in VTU
GetNext operations.
This makes the MV88E6XXX_FLAG_VTU obsolete, thus remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code silently ignores driver errors when configuring
IPSec offload xfrm_state, and falls back to host-based crypto.
Fail the xfrm_state creation if the driver has an error, because
the NIC offloading was explicitly requested by the user program.
This will communicate back to the user that there was an error.
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both esp_output and esp_xmit take a pointer to the ESP header
and place it in esp_info struct prior to calling esp_output_head.
Inside esp_output_head, the call to esp_output_udp_encap
makes sure to update the pointer if it gets invalid.
However, if esp_output_head itself calls skb_cow_data, the
pointer is not updated and stays invalid, causing a crash
after esp_output_head returns.
Update the pointer if it becomes invalid in esp_output_head
Fixes: fca11ebde3 ("esp4: Reorganize esp_output")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 tunneling code tries to insert IPV6_TLV_TNL_ENCAP_LIMIT and
IPV6_TLV_PADN options when an encapsulation limit is defined (the
default is a limit of 4). An MTU adjustment is done to account for
these options as well. However, the options are never present in the
generated packets.
The issue appears to be a subtlety between IPV6_DSTOPTS and
IPV6_RTHDRDSTOPTS defined in RFC 3542. When the IPIP tunnel driver was
written, the encap limit options were included as IPV6_RTHDRDSTOPTS in
dst0opt of struct ipv6_txoptions. Later, ipv6_push_nfrags_opts was
(correctly) updated to require IPV6_RTHDR options when IPV6_RTHDRDSTOPTS
are to be used. This caused the options to no longer be included in v6
encapsulated packets.
The fix is to use IPV6_DSTOPTS (in dst1opt of struct ipv6_txoptions)
instead. IPV6_DSTOPTS do not have the additional IPV6_RTHDR requirement.
Fixes: 1df64a8569c7: ("[IPV6]: Add ip6ip6 tunnel driver.")
Fixes: 333fad5364: ("[IPV6]: Support several new sockopt / ancillary data in Advanced API (RFC3542)")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-04-30
Here's one last batch of Bluetooth patches in the bluetooth-next tree
targeting the 4.12 kernel.
- Remove custom ECDH implementation and use new KPP API instead
- Add protocol checks to hci_ldisc
- Add module license to HCI UART Nokia H4+ driver
- Minor fix for 32bit user space - 64 bit kernel combination
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Figure 1 is full of whitespaces; fix it
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is enslaved to a VRF master, its router interface (RIF)
needs to be destroyed (if exists) and a new one created using the
corresponding virtual router (VR).
>From the driver's perspective, the above is equivalent to an inetaddr
event sent for this netdev. Therefore, when a port netdev (or its
uppers) are enslaved to a VRF master, call the same function that
would've been called had a NETDEV_UP was sent for this netdev in the
inetaddr notification chain.
This patch also fixes a bug when a LAG netdev with an existing RIF is
enslaved to a VRF. Before this patch, each LAG port would drop the
reference on the RIF, but would re-join the same one (in the wrong VR)
soon after. With this patch, the corresponding RIF is first destroyed
and a new one is created using the correct VR.
Fixes: 7179eb5acd ("mlxsw: spectrum_router: Add support for VRFs")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZBeGlAAoJEEg/ir3gV/o+AuMH/2OfS+diXrTMU90tQGfucurg
cPuv2qSGzSzcyFOjMUKL/hgj+y8HcUNZVSqts/LPhUj5CbR8On2jo/3XZb405SMX
1eAffpD5JxDGm4xQCADwkDMRVOuWNbXlTceRMbD+8vDtboTDEZwbaXX20En6MIEW
qcQPX0wv7/u8VpxGlhch2RRvl7+zBhhGCLNpwzkE5K+RggIPguE+F2hLpm+SH9PD
AOHSuwGWnE40In8dZIPqsEnUsmsC9LmUQ17ip8S8dEtGDHMvwDelsKGZcRGMuwoz
wSxpVTWn5JaU0EwN0t+rYtERFH18SqboG3OFwqb27qtRns6ALXIx3Dj1bb9sVBo=
=3qOg
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-04-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2017-04-30
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the PTP related initialization from slowpath start,
the remaining PTT entry is required only in case CONFIG_RFS_ACCEL is set.
Otherwise, it leads to a warning due to it being unused.
Fixes: d179bd1699 ("qed: Acquire/release ptt_ptp lock when enabling/disabling PTP")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed: RoCE related pseudo-fixes
This series contains multiple small corrections to the RoCE logic
in qed plus some debug information and inter-module parameter
meant to prevent issues further along.
- #1, #6 Share information with protocol driver
[either new or filling missing bits in existing API].
- #2, #3 correct error flows in qed.
- #4 add debug related information.
- #5 fixes a minor issue in the HW configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating doorbell BAR partitioning round up the number of
CPUs to the nearest power of 2 so the size of the DPI (per user
section) configured in the hardware will be stored properly and
not truncated.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mechanism to verify RoCE resources are released prior to freeing the
bitmaps. If this is not the case, print what resources were not released.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
