For a000 device the FH was replaced by the TFH.
This is the first patch in a series introducing the
changes stemming from this change.
This patch initializes the TFQ queue table with the new
64 bit register and the relevant TFH configuration
registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the write_prph_64 of pcie to be transport agnostic.
Add direct write as well, as it is needed for a000 HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the scratch buffer is set to 16 bytes and indicates
the size of the bi-directional DMA.
However, next HW generation will perform additional offloading,
and will write the result in the key location of the TX command,
so the size of the bi-directional consistent memory should grow
accordingly - increase it to 40.
Generalize the code to get rid of now irrelevant scratch references.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In MQ environment and new architecture in early stages
we may encounter DMA issues. Track RXB status and bail
out in case we receive index to an RXB that was not
mapped and handed over to HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.
In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.
To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to properly record SKBs that didn't come through
mac80211, don't rely on the IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag
but instead check for ETH_P_PAE directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.
Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.
Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support TDLS when working in DQA mode.
This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In cases of hardware or DMA error, the vid read from
a zeroed location will be 0, and we will access the rxb
at index 0 in the global table, while it may be NULL or
owned by hardware.
Invalidate vid 0 in order to detect the situation and
bail out.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This led to a DMA splat.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This struct member is never set, so remove it.
Since this is the last thing that needs mac80211.h, also change
the includes to no longer use mac80211.h
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value for Channel 14 was wrong. Fix it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3a6 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 38c0f334b3 ("iwlwifi: use coherent DMA memory for command header")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On some of the chipsets MSI & INTA interrupts are disabled by default in
the HW registers, and need to be explicitly enabled to be used.
In case MSI-X isn't used, make sure MSI mode is enabled by setting
the relevant HW register.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure. If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).
Fixes: commit f4a3ee493e ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support of dumping new RFH instead of FH registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc-6 reports the following error if -Werror=unused-const-variable
is enabled.
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:210:21: error:
'iwlagn_loose_lookup' defined but not used
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430f0 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data. This is
unnecessary, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.
This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211(). Fortunately, it's
never used so we can just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code calls restock for mq devices during the init
function, unlike sq where restock is called after init.
This causes an harmless but alarming deadlock warning from
lockdep, to fix this - unify the init code.
Rename the restock functions while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
