The egalax_ts touchscreen modul not report ABS_MT_POSITION_Y proper.
As result it may be, that upper software levels only receive x coordinates well.
Signed-off-by: Heiko Abraham <abrahamh@web.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The trackpoint driver sets various parameter default values, all of
which happen to be power-on defaults (Source: IBM TrackPoint Engineering
Specification, Version 4.0. Also confirmed by empirical data).
By sending the power-on reset command to reset all parameters to
power-on state, we can skip the lengthy process of programming all
parameters. In testing, ~2.5 secs of time writing parameters was reduced
to .35 seconds waiting for power-on reset to complete.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Same as Cintiq 24HDT, DTH2242 has two interfaces sharing one configuration.
This patch ignores the second interface.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MFT device in the Cintiq 24HDT has two interfaces sharing the
same configuration. Without this patch, the driver attempts to
make use of both interfaces, even though the second interface is
not compatible with this driver.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most semi-mt drivers use the slots in a manual way, but really only
need to treat the finger count manually. With this patch, a semi-mt
driver may use the input-mt core for everything else.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
NVIDIA's Tegra20 and Tegra30 supports the 16x8 keyboard matrix and T114
support the 11x8 Key matrix.
Add support for defining the maximum row/columns based on SoC through
proper compatibility.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using devm_ functions can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add match table for device tree binding and dts binding doc.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Event value is wrong. Should be in range -2048 to 2047, but is in
range 0 to 4095. Use s8 to int conversion and remove 0xfff mask.
Signed-off-by: Sebastien Royen <sebastien.royen@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
kfree on a null pointer is a no-op. Hence null check is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/input/misc/ad714x-i2c.c:17:12: warning: 'ad714x_i2c_suspend' defined but not used [-Wunused-function]
drivers/input/misc/ad714x-i2c.c:22:12: warning: 'ad714x_i2c_resume' defined but not used [-Wunused-function]
drivers/input/misc/ad714x-spi.c:20:12: warning: 'ad714x_spi_suspend' defined but not used [-Wunused-function]
drivers/input/misc/ad714x-spi.c:25:12: warning: 'ad714x_spi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/input/misc/adxl34x-spi.c:98:12: warning: 'adxl34x_spi_suspend' defined but not used [-Wunused-function]
drivers/input/misc/adxl34x-spi.c:108:12: warning: 'adxl34x_spi_resume' defined but not used [-Wunused-function]
drivers/input/misc/adxl34x-i2c.c:109:12: warning: 'adxl34x_i2c_suspend' defined but not used [-Wunused-function]
drivers/input/misc/adxl34x-i2c.c:119:12: warning: 'adxl34x_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into next
Merge with mainline to bring in module_platform_driver_probe() and
devm_ioremap_resource().
The PCU is a device installed in the armrest of a plane seat and
is connected to IMS Rave Entertainment System. It has a set of control
buttons (Volume Up/Down, Attendant, Lights, etc) on one side and
gamepad-like controls on the other side.
Originally the device was handled from userspace and because of that
it presents itself on USB bus as a CDC-ACM modem device that however
can not make calls. However the custom handling is not as convenient
as using standard input subsystem facilities. If it was pure input
device it would be possible to continue using userspace solution
(moving it over to uinput), but the device also has backlighted keys
which can not be supported via uinput.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
dev_dbg should end with a new line.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Often a reading can be wrong. This patch assures that this is really a
pen up event and not a false reading.
Based on wm9712: pen up by Teresa Gámez and Christian Hemp.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of interpreting a wrong measurement as pen up, we should
try to read again.
Based on wm9712: pen up by Teresa Gámez and Christian Hemp.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With fast movements, there occured some out of screen jumps with my
touchscreen. The abs_x and abs_y module parameters should fix this by
default, but the driver doesn't actively checks the x/y coordinates.
Instead it seems that the input layer was supposed to drop out of range
inputs, as described in the comments:
"These parameters are used to help the input layer discard out of
range readings and reduce jitter etc"
The input layer documentation describes that values that are not in the
absolute range are also accepted.
So this patch adds a check within the driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
APBPS2 is a PS/2 core part of GRLIB found in SPARC32/LEON
products.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Except for the largish change to the ALPS driver adding "Dolphin V1"
support and Wacom getting a new signature of yet another device, the
rest are straightforward driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mms114 - Fix regulator enable and disable paths
Input: ads7864 - check return value of regulator enable
Input: tc3589x-keypad - fix keymap size
Input: wacom - add support for 0x10d
Input: ALPS - update documentation for recent touchpad driver mods
Input: ALPS - add "Dolphin V1" touchpad support
Input: ALPS - remove unused argument to alps_enter_command_mode()
Input: cypress_ps2 - fix trackpadi found in Dell XPS12
When it uses regulators the mms114 driver checks to see if it managed to
acquire regulators and ignores errors. This is not the intended usage and
not great style in general.
Since the driver already refuses to probe if it fails to allocate the
regulators simply make the enable and disable calls unconditional and
add appropriate error handling, including adding cleanup of the
regulators if setup_reg() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least print a warning if we can't power the device up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The keymap size used by tc3589x is too low, leading to the driver
overwriting other people's memory. Fix this by making the driver
use the automatically allocated keymap provided by
matrix_keypad_build_keymap() instead of allocating one on its own.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is a Wacom device found in Fujitsu Lifebook T902.
Signed-off-by: Stephan Frank <sfrank@cs.tu-berlin.de>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.
Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep. And
it's easier to just fix the initialization sequence.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull second set of s390 patches from Martin Schwidefsky:
"The main part of this merge are Heikos uaccess patches. Together with
commit 0988496433 ("mm: do not grow the stack vma just because of an
overrun on preceding vma") the user string access is hopefully fixed
for good.
In addition some bug fixes and two cleanup patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/module: fix compile warning
qdio: remove unused parameters
s390/uaccess: fix kernel ds access for page table walk
s390/uaccess: fix strncpy_from_user string length check
input: disable i8042 PC Keyboard controller for s390
s390/dis: Fix invalid array size
s390/uaccess: remove pointless access_ok() checks
s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
s390/uaccess: shorten strncpy_from_user/strnlen_user
s390/dasd: fix unresponsive device after all channel paths were lost
s390/mm: ignore change bit for vmemmap
s390/page table dumper: add support for change-recording override bit
