These are all "early clocks" that require initialization just at
of_clk_init() time. Use CLK_OF_DECLARE() to declare them.
This also fixes a problem that was spotted when fw_devlink was
set to 'on' by default: the boards failed to boot. The reason is
that CLK_OF_DECLARE_DRIVER() clears the OF_POPULATED and causes
the consumers of the clock to be postponed by fw_devlink until
the second initialization routine of the clock has been completed.
One of the consumers of the clock is the timer, which is used as a
clocksource, and needs the clock initialized early. Postponing the
timers caused the fail at boot.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210203154332.470587-1-tudor.ambarus@microchip.com
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Register CPU clock as being the master clock prescaler. This would
be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider
between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the
frequencies supported by SAMA7G5 could be directly received from
CPUPLL + master clock prescaler and the extra divider would do no work in
case it would be enabled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-12-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Re-factor master clock driver by splitting it into 2 clocks: prescaller
and divider clocks. Based on registered clock flags the prescaler's rate
could be changed at runtime. This is necessary for platforms supporting
DVFS (e.g. SAMA7G5) where master clock could be changed at run-time.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher
than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at
1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-10-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On SAMA7G5 CPU clock is changed at run-time by DVFS. Since MCK0 and
CPU clock shares the same parent clock (CPUPLL clock) the MCK0 is
also changed by DVFS to avoid over/under clocking of MCK0 consumers.
The lower limit is changed to be able to set MCK0 accordingly by
DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-9-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
MCK0 is changed at runtime by DVFS. Due to this, since not all IPs
are glitch free aware at MCK0 changes, remove MCK0 from parent list
of other clocks (e.g. generic clock, programmable/system clock, MCKX).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-8-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This SoC has the 5th divisor for the mck0 master clock.
Adapt the characteristics accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk-master can have 5 divisors with a field width of 3 bits
on some products.
Change the mask and number of divisors accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Allow SYSPLL and CPUPLL to be referenced as a PMC_TYPE_CORE clock
from phandle in DT.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt commit message, add CPU PLL]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SAMA7G5 specific PLL defines to be referenced in a phandle as a
PMC_TYPE_CORE clock.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt comit message, adapt sama7g5.c]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pmc_data_allocate() has been changed. pmc_data_free() was removed.
Adapt the code taking this into consideration. With this the programmable
clocks were also saved in sama7g5_pmc so that they could be later
referenced.
Fixes: cb783bbbcf ("clk: at91: sama7g5: add clock support for sama7g5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Support qcom SM8150/SM8250 video and display clks
- Change how qcom's display port clks work
* clk-ingenic:
clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate
clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT
clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL
clk: ingenic: Use readl_poll_timeout instead of custom loop
clk: ingenic: Use to_clk_info() macro for all clocks
* clk-at91:
clk: at91: sam9x60: support only two programmable clocks
clk: at91: clk-sam9x60-pll: remove unused variable
clk: at91: clk-main: update key before writing AT91_CKGR_MOR
clk: at91: remove the checking of parent_name
* clk-kconfig:
clk: Restrict CLK_HSDK to ARC_SOC_HSDK
* clk-imx:
clk: imx8mq: Fix usdhc parents order
clk: imx: imx21: Remove clock driver
clk: imx: gate2: Fix a few typos
clk: imx: Fix and update kerneldoc
clk: imx: fix i.MX7D peripheral clk mux flags
clk: imx: fix composite peripheral flags
clk: imx: Correct the memrepair clock on imx8mp
clk: imx: Correct the root clk of media ldb on imx8mp
clk: imx: vf610: Add CRC clock
clk: imx: Explicitly include bits.h
clk: imx8qxp: Support building i.MX8QXP clock driver as module
clk: imx8m: Support module build
clk: imx: Add clock configuration for ARMv7 platforms
clk: imx: Support building i.MX common clock driver as module
clk: composite: Export clk_hw_register_composite()
clk: imx6sl: Use BIT(x) to avoid shifting signed 32-bit value by 31 bits
* clk-qcom:
clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on
clk: qcom: Add display clock controller driver for SM8150 and SM8250
dt-bindings: clock: add QCOM SM8150 and SM8250 display clock bindings
clk: qcom: add video clock controller driver for SM8250
clk: qcom: add video clock controller driver for SM8150
dt-bindings: clock: add SM8250 QCOM video clock bindings
dt-bindings: clock: add SM8150 QCOM video clock bindings
dt-bindings: clock: combine qcom,sdm845-videocc and qcom,sc7180-videocc
clk: qcom: gcc-msm8994: Add missing clocks, resets and GDSCs
clk/qcom: fix spelling typo
clk: qcom: gcc-sdm660: Fix wrong parent_map
clk: qcom: dispcc: Update DP clk ops for phy design
clk: qcom: gcc-msm8939: remove defined but not used variables
clk: qcom: ipq8074: make pcie0_rchng_clk_src static
* clk-prima2:
clk: clk-prima2: fix return value check in prima2_clk_init()
* clk-bcm:
clk: bcm2835: add missing release if devm_clk_hw_register fails
clk: bcm: rpi: Add register to control pixel bvb clk
According to datasheet (Chapter 29.16.13, PMC Programmable Clock Register)
there are only two programmable clocks on SAM9X60.
Fixes: 01e2113de9 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1602686072-28296-1-git-send-email-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix variable set but not used compilation warning.
Fixes: 43b1bb4a9b ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1598338751-20607-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA5D2 datasheet specifies on chapter 33.22.8 (PMC Clock Generator
Main Oscillator Register) that writing any value other than
0x37 on KEY field aborts the write operation. Use the key when
selecting main clock parent.
Fixes: 27cb1c2083 ("clk: at91: rework main clk implementation")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no need to check parent_name variable while assigning it to
init.parent_names. parent_name variable is already checked at
the beginning of at91_clk_register_peripheral() function.
Fixes: 6114067e43 ("clk: at91: add PMC peripheral clocks")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The at91sam9g45_pcr_layout is not used so drop it to fix build warning:
drivers/clk/at91/at91sam9g45.c:49:36: warning:
'at91sam9g45_pcr_layout' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200916161740.14173-1-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via
XTALF register. Values written at bits 2..0 in this register
correspond to the on board crystal oscillator frequency.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-18-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the SAMA7G5 PLLs support multiple outputs (e.g. AUDIO PLL).
For these, split the PLL clock in two: fractional clock and
divider clock. In case PLLs supports multiple outputs (since these
outputs are dividers (with different settings) sharing the same
fractional part), it will register one fractional clock and multiple
divider clocks (dividers sharing the fractional clock).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-17-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some peripheral clocks on SAMA7G5 supports requesting parent to change
its rate (image related clocks: csi, csi2dc, isc). Add support
so that if registered with this option the clock rate to be
requested from parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-14-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add master clock support (MCK1..4) for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-13-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pass the ID of changeable parent at registration. This will allow
the scalability of this clock driver with regards to the changeable
parent ID for versions of this IP where changeable parent is not the
last one in the parents list (e.g. SAMA7G5). With this the clock flags
are set to zero in case we have no changeable parent. Also in
clk_generated_best_diff() the *best_diff variable is check against
tmp_diff variable using ">=" operator instead of ">" so that in case
the requested frequency could be obtained using fix parents + gck
dividers but the clock also supports changeable parent to be able
to force the usage of the changeable parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In commit a436c2a447 ("clk: at91: add sam9x60 PLL driver")
the fractional part of PLL wasn't set on registers but it was
calculated and taken into account for determining div and mul
(see sam9x60_pll_get_best_div_mul()).
Fixes: a436c2a447 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to datasheet the range of 600-1200MHz is for the
frequency generated by the fractional part of the PLL (namely
Fcorepllck according to datasheet). With this in mind the output
range of the PLL itself (fractional + div), taking into account
that the divider is 8 bits wide, is 600/256-1200Hz=2.3-1200MHz.
Fixes: a436c2a447 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use logical or for range check. In case bestrate is not in
characteristics->output[0].min..characteristics->output[0].max
range we should return -ERANGE.
Fixes: a436c2a447 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
__clk_determine_rate() may return error. Skip the current step
in case of error.
Fixes: 1a1a36d72e ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
syscon_node_to_regmap() will make the created regmap get and enable the
first clock it can parse from the device tree. This clock is not needed to
access the registers and should not be enabled at that time.
Use device_node_to_regmap to resolve this as it looks up the regmap in
the same list but doesn't care about the clocks. This issue is detected
by lockdep when booting the sama5d3 with a device tree containing the
new clk bindings.
This fix already happened in 6956eb33ab ("clk: at91: fix possible
deadlock") for the drivers that had been migrated to the new clk binding
back then. This does the same for the new drivers as well.
Fixes: 01e2113de9 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200703073236.23923-1-a.fatoum@pengutronix.de
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We need to have clocks accessible via phandle to select them
as peripheral clock parent using assigned-clock-parents in DT.
Add support for PLLACK/PLLBCK/AUDIOPLLCK clocks where available.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lkml.kernel.org/r/fa39cc10dab8341ea4bc2b7152be9217b2cd34a5.1588630999.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
majority of the diff is the normal collection of driver additions for new SoCs
and non-critical clk data fixes and updates. The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and Unisoc
support added a handful of big drivers for new SoCs but that's not really the
whole story because those new drivers tend to add large numbers of lines of clk
data. There's a handful of AT91 clk drivers added this time around too and a
bunch of improvements to drivers like the i.MX driver. All around lots of
updates and fixes in various clk drivers which is good to see.
The core framework has only one real major change which has been baking in next
for the past couple months. It fixes the framework so that it stops caching a
clk's phase when the phase clk_op returns an error. Before this change we would
consider some negative errno as a phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for pll1443x table,
and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need to
change ARM PLL frequency. Thus, we can support core running above
1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate for
getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl6JDxURHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSU51A/+OzAA4HyywcSwLWMhUbyWI0hWis8/Gdtv
/tIOPY/+J/Wi+2vFXoZEQWr/GViEEC1ylQwtkc/cm1WklEka/+q+GJFawyyIfX2i
ovofDWw5lJd4/ACaOqV4ryEppwHnPUvASvoIOUXX6IwauNQzI0dRZWTOLTg2YW7x
uvI5OtQ8o71+bM+VL1tuhWvN/4Zx9tALNU9yhaRhHdafR+xQ0d4x5bBQo8MG/2E0
3xIbRqGbhO6XfNiKAjgKcI3jtHn006LK1/1AjyXUETWzu5Zcg2SYb/YAah39RKLZ
FTV+xY39C8JBLPt6ZLrBu9mPDcoQOWohmnDLki0qm65cfVs/tbDX3kwp3ixCly7y
jSCqNpl7RuWcbjMe8YesakhJc1IFICQts08KsM6dPipL+7iAv++fNQrfrnXf0cDx
cPCgDkepos/aRhNXmVFdxf2FRKkIQjYpdAPFdYSvLv6MK0Dk6G7/EhOOXA10Z2BU
BojY8tUx/YaC8sRbnZlhitYfpqDVFzdihL2G6W31iUbt1sKYR6t6Szhct2EbRTOQ
69bUy2lw7M8pk1Remp0LqdrVUDYLy0/X3dVaa/teIaZt2Ac1NnWzHw9LMmnlFFEG
GxuZy5Q5fCKbAf0tSkD4Gzb9z8f0pzAyfdlpGsY7+eEEWloc4yNFCcFcNyzJTXWV
4kdye0klUPs=
=ZoI6
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's not much to see in the core framework this time around.
Instead the majority of the diff is the normal collection of driver
additions for new SoCs and non-critical clk data fixes and updates.
The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and
Unisoc support added a handful of big drivers for new SoCs but that's
not really the whole story because those new drivers tend to add large
numbers of lines of clk data. There's a handful of AT91 clk drivers
added this time around too and a bunch of improvements to drivers like
the i.MX driver. All around lots of updates and fixes in various clk
drivers which is good to see.
The core framework has only one real major change which has been
baking in next for the past couple months. It fixes the framework so
that it stops caching a clk's phase when the phase clk_op returns an
error. Before this change we would consider some negative errno as a
phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and
at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for
pll1443x table, and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need
to change ARM PLL frequency. Thus, we can support core running
above 1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate
for getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for
imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock
Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and
M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (146 commits)
clk: sprd: fix to get a correct ibias of pll
dt-bindings: imx8mm-clock: Fix the file path
dt-bindings: imx8mq-clock: Fix the file path
clk: qcom: rpmh: Drop unnecessary semicolons
clk: qcom: rpmh: Simplify clk_rpmh_bcm_send_cmd()
clk: tegra: Use NULL for pointer initialization
clk: sprd: add clocks support for SC9863A
clk: sprd: support to get regmap from parent node
clk: sprd: Add macros for referencing parents without strings
clk: sprd: Add dt-bindings include file for SC9863A
dt-bindings: clk: sprd: add bindings for sc9863a clock controller
dt-bindings: clk: sprd: rename the common file name sprd.txt to SoC specific
clk: sprd: add gate for pll clocks
MAINTAINERS: dt: update reference for arm-integrator.txt
clk: mmp2: Fix bit masks for LCDC I/O and pixel clocks
clk: mmp2: Add clock for fifth SD HCI on MMP3
dt-bindings: marvell,mmp2: Add clock id for the fifth SD HCI on MMP3
clk: mmp2: Add clocks for the thermal sensors
dt-bindings: marvell,mmp2: Add clock ids for the thermal sensors
clk: mmp2: add the GPU clocks
...
Move SAM9X60's PLL register offsets to PMC header so that the
definitions would also be available from arch/arm/mach-at91/pm_suspend.S.
This is necessary to disable/enable PLLA for SAM9X60 on suspend/resume.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1579522208-19523-7-git-send-email-claudiu.beznea@microchip.com
