This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449036584-105393-2-git-send-email-libin.yang@linux.intel.com
This removes pre/post_wm_update from intel_crtc->atomic, and
creates atomic state for it in intel_crtc.
Changes since v1:
- Rebase on top of wm changes.
Changes since v2:
- Split disable_cxsr into a separate patch.
Changes since v3:
- Move some of the changes to intel_wm_need_update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56603A49.5000507@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The goal is to call FBC enable/disable only once per modeset, while
activate/deactivate/update will be called multiple times.
The enable() function will be responsible for deciding if a CRTC will
have FBC on it and then it will "lock" FBC on this CRTC: it won't be
possible to change FBC's CRTC until disable(). With this, all checks
and resource acquisition that only need to be done once per modeset
can be moved from update() to enable(). And then the update(),
activate() and deactivate() code will also get simpler since they
won't need to worry about the CRTC being changed.
The disable() function will do the reverse operation of enable(). One
of its features is that it should only be called while the pipe is
already off. This guarantees that FBC is stopped and nothing is
using the CFB.
With this, the activate() and deactivate() functions just start and
temporarily stop FBC. They are the ones touching the hardware enable
bit, so HW state reflects dev_priv->crtc.active.
The last function remaining is update(). A lot of times I thought
about renaming update() to activate() or try_to_activate() since it's
called when we want to activate FBC. The thing is that update() may
not only decide to activate FBC, but also deactivate or keep it on the
same state, so I'll leave this name for now.
Moving code to enable() and disable() will also help in case we decide
to move FBC to pipe_config or something else later.
The current patch only puts the very basic code on enable() and
disable(). The next commits will take care of moving more stuff from
update() to the new functions.
v2:
- Rebase.
- Improve commit message (Chris).
v3: Rebase after changing the patch order.
v4: Rebase again after upstream changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
The long term goal is to have enable/disable as the higher level
functions and activate/deactivate as the lower level functions, just
like we do for PSR and for the CRTC. This way, we'll run enable and
disable once per modeset, while update, activate and deactivate will
be run many times. With this, we can move the checks and code that
need to run only once per modeset to enable(), making the code simpler
and possibly a little faster.
This patch is just the first step on the conversion: it starts by
converting the current low level functions from enable/disable to
activate/deactivate. This patch by itself has no benefits other than
making review and rebase easier. Please see the next patches for more
details on the conversion.
v2:
- Rebase.
- Improve commit message (Chris).
v3: Rebase after changing the patch order.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
There's no need to reevaluate the status of every single crtc when a
single crtc changes its state.
With this, we're cutting the case where due to a change in pipe B,
intel_fbc_update() is called, then intel_fbc_find_crtc() concludes FBC
should be enabled on pipe A, then it completely rechecks the state of
pipe A only to conclude FBC should remain enabled on pipe A. If any
change on pipe A triggers a need to recompute whether FBC is valid on
pipe A, then at some point someone is going to call
intel_fbc_update(PIPE_A).
The addition of intel_fbc_deactivate() is necessary so we keep track
of the previously selected CRTC when we do invalidate/flush. We're
also going to continue the enable/disable/activate/deactivate concept
in the next patches.
v2: Rebase.
v3: Rebase after changing the patch order.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
The .get_config() hooks should not reference anything in crtc->config,
everything should be based on the passed in pipe_config instead. So
don't dig out the cpu_transcoder from crtc->config on ddi platfforms,
and also avoid using the encoder->crtc link and instead look up the
pipe via pipe_config->base.crtc.
I don't think this will actually fix anything since during the initial
state readout we set up the encoder->crtc link prior to calling
.get_config(), and during the modeset state check the encoder->crtc
ought to be correct anyway since it's that state we just programmed.
But this seems the right thing to do anyway.
While at it, do some house cleaning on the local variables in the
.infoframe_enabled() hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-11-20-rebased:
4 weeks because of my vacation, so a bit more:
- final bits of the typesafe register mmio functions (Ville)
- power domain fix for hdmi detection (Imre)
- tons of fixes and improvements to the psr code (Rodrigo)
- refactoring of the dp detection code (Ander)
- complete rework of the dmc loader and dc5/dc6 handling (Imre, Patrik and
others)
- dp compliance improvements from Shubhangi Shrivastava
- stop_machine hack from Chris to fix corruptions when updating GTT ptes on bsw
- lots of fifo underrun fixes from Ville
- big pile of fbc fixes and improvements from Paulo
- fix fbdev failures paths (Tvrtko and Lukas Wunner)
- dp link training refactoring (Ander)
- interruptible prepare_plane for atomic (Maarten)
- basic kabylake support (Deepak&Rodrigo)
- don't leak ringspace on resets (Chris)
drm-intel-next-2015-10-23:
- 2nd attempt at atomic watermarks from Matt, but just prep for now
- fixes all over
* tag 'drm-intel-next-2015-11-20-merged' of git://anongit.freedesktop.org/drm-intel: (209 commits)
drm/i915: Update DRIVER_DATE to 20151120
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: take a power domain ref only when needed during HDMI detect
drm/i915: Tear down fbdev if initialization fails
async: export current_is_async()
Revert "drm/i915: Initialize HWS page address after GPU reset"
drm/i915: Fix oops caused by fbdev initialization failure
drm/i915: Fix i915_ggtt_view_equal to handle rotation correctly
drm/i915: Stuff rotation params into view union
drm/i915: Drop return value from intel_fill_fb_ggtt_view
drm/i915 : Fix to remove unnecsessary checks in postclose function.
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Remove platform specific *_dp_detect() functions
drm/i915: Don't do edp panel detection in g4x_dp_detect()
drm/i915: Send TP1 TP2/3 even when panel claims no NO_TRAIN_ON_EXIT.
drm/i915: PSR: Don't Skip aux handshake on DP_PSR_NO_TRAIN_ON_EXIT.
drm/i915: Reduce PSR re-activation time for VLV/CHV.
drm/i915: Delay first PSR activation.
drm/i915: Type safe register read/write
...
DSI has quite a few special cases, like DP, so add it to crtc
state. This way we can get rid of a number of intel_pipe_has_type()
checks for DSI. This isn't necessarily the prettiest way, but it's a
step towards being aligned with what's being done with other encoders.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448619706-21293-3-git-send-email-jani.nikula@intel.com
I noticed that intel_fbdev->our_mode is unused. Introduced by
79e539453b ("DRM: i915: add mode setting support").
Then I noticed that intel_fbdev->fbdev_list is unused as well.
Introduced by 386516744b ("drm/fb: fix fbdev object model +
cleanup properly.") in i915, nouveau and radeon.
Subsequently cargo culted to amdgpu, ast, cirrus, qxl, udl,
virtio and mgag200.
Already removed from the latter with cc59487a05 ("drm/mgag200:
'fbdev_list' in 'struct mga_fbdev' is not used").
Remove it from the others.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let us print human-parseable values from the power domain code; upcoming
display code also wants to use it.
This requires moving it out of i915_debugfs.c, as that is only conditionally
compiled.
v2: Move it out of the header.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-1-git-send-email-daniels@collabora.com
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
Replace the is_sdvob bool and some sdvo_reg checks with enum port. This
makes the SDVO code look more modern, and gets rid of explicit register
offset checks in the code which will hamper register type checking.
v2: Add assert_sdvo_port_valid() (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1446838199-3666-1-git-send-email-ville.syrjala@linux.intel.com
It was created at 'commit aabc95dcf2 (drm/i915: Dont -ETIMEDOUT
on identical new and previous (count, crc).")' becase the counter
wasn't reliable.
Now that we properly wait for the counter to be reset we can rely
a bit more in the counter.
Also that patch stopped to return -ETIMEDOUT so the test case is
unable to skip when it is unreliable and end up in many fails
that should be skip instead.
So, with the counter more reliable we can remove
this hack that just makes things more confusing when test cases
are really expecting the same CRC and let test case skip if that's
not the case.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-5-git-send-email-patrik.jakobsson@linux.intel.com
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-1-git-send-email-patrik.jakobsson@linux.intel.com
We need to initialize the display core part early, before initializing
the rest of the display power state. This is also described in the bspec
termed "Display initialization sequence". Atm we run this sequence
during driver loading after power domain HW state initialization which
is too late and during runtime suspend/resume which is unneeded and can
interere with DMC functionality which handles HW resources toggled
by this init/uninit sequence automatically. The init sequence must be
run as the first step of HW power state initialization and during
system resume. The uninit sequence must be run during system suspend.
To address the above move the init sequence to the initial HW power
state setup and the uninit sequence to a new power domains suspend
function called during system suspend.
As part of the init sequence we also have to reprogram the DMC firmware
as it's lost across a system suspend/resume cycle.
After this change CD clock initialization during driver loading will
happen only later after other dependent HW/SW parts are initialized,
while during system resume it will get initialized as the last step of
the init sequence. This distinction can be removed by some refactoring
of platform independent parts. I left this refactoring out from this
series since I didn't want to change non-SKL parts. This is a TODO for
later.
v2:
- fix error path in i915_drm_suspend_late()
- don't try to re-program the DMC firmware if it failed to load
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447774433-20834-1-git-send-email-imre.deak@intel.com
Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().
The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.
So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.
v2 (from Paulo):
- Write a commit message since the original patch left it empty.
- Rebase after the intel_power_well_{en,dis}able rename.
- Use lookup_power_well() instead of hardcoded indexes.
Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com
Rather than computing on demand, store also the aux data reg
offsets under intel_dp.
v2: Duplicate some code to make things less magic (Jani)
v3: Use PORT_B registers for invalid ports in g4x_aux_data_reg()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-6-git-send-email-ville.syrjala@linux.intel.com
As all csr firmware related opertion are not using any
any data structures of drm framework level, so better to
use dev_priv instead of dev. it's a new style! :)
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-9-git-send-email-imre.deak@intel.com
This removes two anti-patterns:
- Locking shouldn't be used to synchronize with async work (of any
form, whether callbacks, workers or other threads). This is what the
mutex_lock/unlock seems to have been for in intel_csr_load_program.
Instead ordering should be ensured with the generic
wait_for_completion()/complete(). Or more specific functions
provided by the core kernel like e.g.
flush_work()/cancel_work_sync() in the case of synchronizing with a
work item.
- Don't invent own completion like the following code did with the
(already removed) wait_for(csr_load_status_get()) pattern - it's
really hard to get these right when you want them to be _really_
correct (and be fast) in all cases. Furthermore it's easier to read
code using the well-known primitives than new ones using
non-standard names.
Before enabling/disabling DC6 check if the firmware is loaded
successfully. This is guaranteed during runtime s/r, since otherwise we
don't enable RPM, but not during system s/r.
Note that it's still unclear whether we need to enable/disable DC6
during system s/r, until that's clarified, keep the current behavior and
enable/disable DC6.
Also after this patch there is a race during system s/r where the
firmware may not be loaded yet, that's addressed in an upcoming patch.
v2-v3:
- unchanged
v4:
- rebased on latest drm-intel-nightly
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: added code and note about checking if the firmware loaded ok,
before enabling/disabling it]
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447341037-2623-1-git-send-email-imre.deak@intel.com
Avoids non-static functions since all the callers are in intel_rpm.c.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: removed note about reg definitions from commit message, since
it's not relevant any more]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
[Jani: make assert_csr_loaded static]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-4-git-send-email-imre.deak@intel.com
Reading the driver load/unload code leaves one confused as there's
an async_schedule() in the load, but not async_synchronize_full()
in sight. In fact it's hidden inside intel_fbdev.c. So let's move the
async_schedule() into intel_fbdev.c as well so that it's next to the
async_synchronize_full(), which should make the relationship easier
to see.
Plus this way we won't schedule a nop function call when fbdev is
disabled. And we were passing a pointer to a static inline
function to async_schedule(), which seems rather dubious to me.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446815313-9490-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Doing the IBX transcoder B workaround causes underruns on
pipe/transcoder A. Just hide them by disabling underrun reporting for
pipe A around the workaround.
It might be possible to avoid the underruns by moving the workaround
to be applied only when enabling pipe A. But I was too lazy to try it
right now, and the current method has been proven to work, so didn't
want to change it too hastily.
Note that this can re-enable underrun reporting on pipe A if was
already disabled due to a previous actual underrun. But that's OK, we
may just get a second underrun report if another real underron occurrs
on pipe A.
v2: Note that pipe A underruns can get re-enabled due to this (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1446225802-11180-1-git-send-email-ville.syrjala@linux.intel.com
Due to the shared error interrupt on IVB/HSW and CPT/PPT we may not
always get an interrupt on a FIFO underrun. But we can always do an
explicit check (like we do on GMCH platforms that have no underrun
interrupt).
v2: Drop stale kerneldoc for i9xx_check_fifo_underruns() (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1446225741-11070-1-git-send-email-ville.syrjala@linux.intel.com
VMA offsets are 64 bits. Plane surface offsets are in ggtt and
the hardware register to set this is thus 32 bits. Be explicit
about these and convert carefully to from vma to final size.
This will make sparse happy by not creating 32bit pointers out
of 64bit vma offsets.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446204375-29831-1-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
In order to prepare for a link training with DDI, the state machine
would call intel_ddi_prepare_link_retrain(). To remove the dependency to
the hardware information, replace that direct call with a callback.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com
I wanted to add yet another check to intel_fbc_update() and realized
I would need to create yet another enum no_fbc_reason case. So I
remembered this patch series that Damien wrote a long time ago and
nobody ever reviewed, so I decided to reimplement it since the code
changed a lot since then.
Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445964628-30226-2-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Make pinning and waiting a separate step, and wait for object idle
without struct_mutex held.
Changes since v1:
- Do not wait when a reset is in progress.
- Remove call to i915_gem_object_wait_rendering for
intel_overlay_do_put_image (Chris Wilson)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Move it from intel_crtc_atomic_commit to prepare_plane_fb.
Waiting is done before committing, otherwise it's too late
to undo the changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Don't forget to actually check the cstate->active value when
tallying up the number of active CRTC's. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59561/
A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.
While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.
v2: Don't move cxsr_allowed to state (Maarten)
v3: Only calculate watermarks in state. Still keep active watermarks in
intel_crtc itself. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59556/
The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update. However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call. Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60372/
Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.
Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60367/
Previously rotation was ignored and wrong stride programmed
into the plane registers resulting in a corrupt image on screen.
v2: Do not access potentialy old plane state at flip time,
but store the rotation value at the time of queing the flip.
(Ville)
v3: No need to pass rotation to intel_queue_mmio_flip since it
is available in the crtc. (Ville)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Testcase: igt/kms_rotation_crc/primary-rotation-90-flip-stress (SKL)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially in cases where pre-os does not enable display, cdclk might
not be in sane state. During sanitization initialize cdclk with maximum
value till we get dynamic cdclk support.
v2: Check if BIOS programmed correctly rather than always calling init
- Do validation of programmed cdctl and what it is expected
- Only do slk_init_cdclk if validation failed else reuse BIOS
programmed value
v3: Move the validation logic in a separate sanitize function (Ville)
v4: No need to check LCPLL after sanitize and use max_cdclk_freq instead
of hardcoded value (Ville)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344992-14658-1-git-send-email-shobhit.kumar@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
atomic->disabled_planes is a hack that had to exist because
prepare_fb was only called when a new fb was set. This messed
up fb tracking in some circumstances like aborts from
interruptible waits. As a result interruptible waiting in
prepare_plane_fb was forbidden, but other errors could still
cause frontbuffer tracking to be messed up.
Now that prepare_fb is always called, this hack is no longer
required and prepare_fb may fail without consequences.
Changes since v1:
- Clean up a few fb tracking warnings by changing plane->fb to
plane->state->fb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mmio register access after dc6/dc5 entry is not allowed when
DC6 power states are enabled according to bspec (bspec-id 0527),
so enabling dc6 as the last call in suspend flow.
Addtional note from Imre:
Currently we keep DC6 enabled during modesets and DPAUX transfers, which
is not allowed according to the specification. This can lead at least to
PLL locking failures, DPAUX timeouts and prevent deeper package power
states (PC9/10). Fix this for now by enabling DC6 only when we know the
above events (modeset, DPAUX) can't happen.
This a temporary solution as some issues are still unsolved as described
in [1] and [2], we'll address those as a follow-up.
[1]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077669.html
[2]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077787.html
v1: Initial version.
v2: Based on review comment from Daniel,
- created a seperate patch for csr uninitialization set call.
v3: Rebased on top of latest code.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a squash of the following commits:
Revert "drm/i915: Drop intel_update_sprite_watermarks"
This reverts commit 47c99438b5.
Revert "drm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check"
This reverts commit 7809e5ae35.
Revert "drm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v3)"
This reverts commit 3a05f5e2e7.
With these reverts, SKL finally stops failing every single FBC test
with FIFO underrun error messages. After some brief testing, it also
seems that this commit prevents the machine from completely freezing
when we run igt/kms_fbc_crc (see fd.o #92355).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92355
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's been reported that the atomic watermark series triggers some
regressions on SKL, which we haven't been able to track down yet. Let's
temporarily revert these patches while we track down the root cause.
This commit squashes the reverts of:
76305b1 drm/i915: Calculate watermark configuration during atomic check (v2)
a4611e4 drm/i915: Don't set plane visible during HW readout if CRTC is off
a28170f drm/i915: Calculate ILK-style watermarks during atomic check (v3)
de4a9f8 drm/i915: Calculate pipe watermarks into CRTC state (v3)
de165e0 drm/i915: Refactor ilk_update_wm (v3)
Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-October/077190.html
Cc: "Zanoni, Paulo R" <paulo.r.zanoni@intel.com>
Cc: "Vetter, Daniel" <daniel.vetter@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Don't forget to actually check the cstate->active value when
tallying up the number of active CRTC's. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.
While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.
v2: Don't move cxsr_allowed to state (Maarten)
v3: Only calculate watermarks in state. Still keep active watermarks in
intel_crtc itself. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update. However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call. Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.
Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.
This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.
Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handle the HDMI aspect ratio property the same way in the SDVO code
as we handle it in the HDMI code.
v2: Remove stray whitespace change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The vblank counts are u32 so make flip_queued_vblank and
flip_ready_vblank u32 as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for NV12 support.
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I only tested this on BDW and SKL, but since the register description
is the same ever since gen4, let's assume that all gens take the same
register format. If that's not true, then hopefully someone will
bisect a bug to this patch and we'll fix it.
Notice that the wrong fence offset register just means that the
hardware tracking will be wrong.
Testcases:
- igt/kms_frontbuffer_tracking/fbc-1p-primscrn-pri-shrfb-draw-mmap-gtt
- igt/kms_frontbuffer_tracking/fbc-2p-primscrn-pri-shrfb-draw-mmap-gtt
v2:
- Add intel_crtc->adjusted_{x,y} so this code can work independently
of intel_gen4_compute_page_offset(). (Ville).
- This version also works on SKL.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I used these additional fields to track down the issue I saw on HSW.
v2: move debug fields into a substruct (Ville)
v3: clean up debug code more (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Instead of doing a hack during primary plane commit the state
is updated during atomic evasion. It handles differences in
pipe size and the panel fitter.
This is continuing on top of Daniel's work to make faster
modesets atomic, and not yet enabled by default.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet:
- simplify/future-proof if ladder that Jesse spotted
- resolve conflict in pipe_config_check and don't spuriously move the
code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the intel_connector initialized to intel_hdmi
display, during the init phase, just like the other encoders do.
This attachment is very useful when we need to extract the connector
pointer during the hotplug handler function
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to have a separate flag for tps3 as the information is
only used at one location. Move the logic there to make it easier to
follow.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This makes the error message slightly more useful.
Changes since v1:
- Use ktime_get() while irqs are still disabled. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's already a per crtc member that can be used for it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP MST encoder config function never sets ddi_pll_sel, even though
its value is programmed in its ->pre_enable() hook. That used to work
because a new pipe_config was kzalloc'ed at every modeset, and the value
of zero selects the highest clock for the PLL. Starting with the commit
below, the value of ddi_pll_sel is preserved through modesets, and since
the correct value wasn't properly setup by the MST code, it could lead
to warnings and blank screens.
commit 8504c74c7a
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 11:51:50 2015 +0300
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91628
Cc: stable@vger.kernel.org # 7e6313a251 drm/i915: Don't use link_bw for PLL setup
Cc: stable@vger.kernel.org
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can be made static there. No functional changes.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add vlv_dport_to_phy() and fix up the return values of
vlv_dport_to_channel() and vlv_pipe_to_channel() to use
the appropriate enums.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
We only need the link_bw/rate_select parameters when starting link
training, and they should be computed based on the currently active
config, so throw them out from intel_dp and just compute on demand.
Toss in an extra debug print to see rate_select in addition to link_bw,
as the latter may be 0 for eDP 1.4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().
There should be no functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."
However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.
So we face cases like this:
first get_sink_crc operation:
count: 0, crc: 000000000000
count: 1, crc: c101c101c101
returned expected crc: c101c101c101
secont get_sink_crc operation:
count: 1, crc: c101c101c101
count: 0, crc: 000000000000
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
But also the reset to 0 should be faster resulting into:
get_sink_crc operation:
count: 1, crc: c101c101c101
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).
If the pair changed you have your valid CRC.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.
But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a few core drm patches to be able to merge Maarten's series to
convert DPMS over to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Due to the way busy_bits was handled, we were not doing any flushes if
we didn't previously get an invalidate. Since it's possible to get
flushes without an invalidate first, remove the busy_bits early
return.
So now that we don't have the busy_bits guard anymore we'll need the
origin check for the GTT tracking (we were not doing anything on GTT
flushes due to the GTT check at invalidate()).
As a last detail, since we can get multiple consecutive flushes,
disable FBC before updating it, otherwise intel_fbc_update() will just
keep FBC enabled instead of restarting it.
Notice that this does not fix any of the current IGT tests due to the
fact that we still have a few intel_fbc() calls at points where we
also have the frontbuffer tracking calls: we didn't fully convert to
frontbuffer tracking yet. Once we remove those calls and start relying
only on the frontbuffer tracking infrastructure we'll need this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crystalcove pmic support from Shobhit. Patch series has all acks/r-bs from
other mainainers so ok to pull into drm-next. But I'm cc'ing all other
maintainers as fyi and in case they want to pull it into their trees too
to avoid conflicts.
* tag 'topic/crc-pmic-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
mfd: Add GPIOLIB dependency if INTEL_SOC_PMIC is to be enabled
drm/i915: Backlight control using CRC PMIC based PWM driver
drm/i915: Use the CRC gpio for panel enable/disable
pwm: crc: Add Crystalcove (CRC) PWM driver
mfd: intel_soc_pmic_core: ADD PWM lookup table for CRC PMIC based PWM
mfd: intel_soc_pmic_crc: Add PWM cell device for Crystalcove PMIC
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal
gpiolib: Add support for removing registered consumer lookup table
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we both set mode->private_flags to some value and also use
the pipe_config quirk. But since the pipe_config quirk isn't tied to
the lifetime of the mode object we need to check both.
Simplify this by only using mode.private_flags and stop using the
INHERITED_MODE quirk. Also for clarity add an explicit #define for
that driver priavete mode flag.
By using crtc_state->mode_changed we can also remove the recalc local
variable.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This can only fail because of a bug in the code.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Squash in follow-up to also remove start_vbl_count from
intel_crtc->atomic and put it into the intel_crtc directly - it's not
precomputed state.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Huzzah! \o/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous commit converted hw readout to atomic, all the new_*
members were used for restoring the old state, but with the
conversion of suspend to atomic there's no use left for them.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All non-primary planes get disabled during hw readout,
this reduces complexity and means not having to do some plane
visibility checks during the first commit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing depends on this outside initial hw readout, so keep this
struct on the stack instead.
Changes since v1:
- Remove unrelated changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's not much point for calculating the changes for the old
state. Instead just disable all scalers when disabling. It's
probably good enough to just disable the crtc_scaler, but just in
case there's a bug disable all scalers.
This means intel_atomic_setup_scalers is only called in the crtc
check function now, so all the transitional code can be removed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since flush actually means invalidate + flush we need to force psr
exit on PSR flush.
On Core platforms there is no way to disable hw tracking and
do the pure sw tracking so we simulate it by fully disable psr and
reschedule a enable back.
So a good idea is to minimize sequential disable/enable in cases we
know that HW tracking like when flush has been originated by a flip.
Also flip had just invalidated it already.
It also uses origin to minimize the a bit the amount of
disable/enabled, mainly when flip already had invalidated.
With this patch in place it is possible to do a flush on dirty areas
properly in a following patch.
v2: Remove duplicated exit on HSW+Sprites as pointed out by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be useful to PSR and FBC once we start making
dirty fb calls to also flush frontbuffer.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the cool kids use dev_priv and FBC wants to be cool too.
We've been historically using struct drm_device on the FBC function
arguments, but we only really need it for intel_vgpu_active(): we can
use dev_priv everywhere else. So let's fully switch to dev_priv since
I'm getting tired of adding "struct drm_device *dev = dev_priv->dev"
everywhere.
If I get a NACK here I'll propose the opposite: convert all the
functions that currently take dev_priv to take dev.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.
With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.
v2:
- Rebase (6 months later)
- Also lock debugfs and stolen.
v3:
- Don't lock a single value read (Chris).
- Replace lockdep assertions with WARNs (Daniel).
- Improve commit message.
- Don't forget intel_pre_plane_update() locking.
v4:
- Don't remove struct_mutex at intel_pre_plane_update() (Chris).
- Add comment regarding locking dependencies (Chris).
- Rebase after the stolen code rework.
- Rebase again after drm-intel-nightly changes.
v5:
- Rebase after the new stolen_lock patch.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.
We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.
v2:
- Rebase after the remove_node() changes on the previous patch.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the platform the port clock fed to the pipe can be the PLL's
post-divided fast clock rate or a /5 divided version of it. To make this
more obvious across the platforms calculate this port clock along with
the rest of the PLL parameters.
This is also needed by the next patch where we can reuse the CHV helper
for the BXT PLL HW readout code; so export the corresponding helper.
While at it also add a more descriptive name to the helpers and a
comment explaining what's being calculated.
No functional change.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.
Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
v3: Rebase after a long time and atomic path changes.
Accept Ville suggestion of not check !fb
v4: Re-factore on dinq
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Avoid some 'switch (plane->type)' by storing the fronbuffer_bits in
intel_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: use singular frontbuffer_bits in intel_plane since a plan can
only ever have one bit. Discussed with Ville on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The frontbuffer code gives us accurate information about activity,
let's use it. Again this should avoid unecessary updates when multiple
screens are on.
Also realign function paramaters, I couldn't resist that bit of OCD.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The current/old frontbuffer might still have gpu frontbuffer rendering
pending. But once flipped it won't have the corresponding frontbuffer
bits any more and hence the request retire function won't ever clear
the corresponding busy bits. The async flip tracking (with the
flip_prepare and flip_complete functions) already does this, but
somehow I've forgotten to do this for synchronous flips.
Note that we don't track outstanding rendering of the new framebuffer
with busy_bits since all our plane update code waits for previous
rendering to complete before displaying a new buffer. Hence a new
buffer will never be busy.
v2: Drop the spurious inline Ville spotted.
v3: Don't touch flip_bits in the synchronsou frontbuffer_flip
function, noticed by Paulo.
v4: Remove one more inline that slipped through (Paulo).
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testcase: igt/kms_frontbuffer_tracking/fbc-modesetfrombusy
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.
v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).
The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).
The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.
v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.
v4: Updated comments from review feedback (Tomas Elf)
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch doesn't have any functional change, but organize fruntbuffer
invalidate and busy by removing unecesarry signature argument for ring.
It was unsed on mark_fb_busy and only used on fb_obj_invalidate for the
same ORIGIN_CS usage. So let's clean it a bit
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The skylake scalers depend on the cdclk freq, but that frequency can
change during a modeset. So when a modeset happens calculate the new
cdclk in the atomic state. With the transitional helpers gone the
cached value can be used in the scaler, and committed after all
crtc's are disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By making color key atomic there are no more transitional helpers.
The plane check function will reject the color key when a scaler is
active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the initial state, and add a quirk to force add all planes
to crtc_state->plane_mask during initial commit. This will disable
all planes during the initial modeset.
The initial plane quirk is temporary, and will go away when hardware
readout is fully atomic, and the watermark updates in intel_sprite.c
are removed.
Changes since v1:
- Unset state->visible on !primary planes.
- Do not rely on the plane->crtc pointer in intel_atomic_plane,
instead assume planes are invisible until modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is probably intended to be be done during vblank evasion.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The idea was good, but planes can have a fb even though
they're disabled. This makes the force argument useless
and always true, because only the commit function updates
state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By passing crtc_state to the check_plane functions a lot of duplicated
code can be removed. There are still some transitional helper calls,
they will be removed later.
Changes since v1:
- Revert state->visible changes.
- Use plane->state->crtc instead of plane->crtc.
- Use drm_atomic_get_existing_crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes it easier to verify that no changes are done when
calling this from crtc instead.
Changes since v1:
- Make intel_wm_need_update static and always check it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 2c310b9d2859863826c3688c88218d607d5dd19a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon May 18 12:28:52 2015 +0200
drm/i915: Split skl_update_scaler, v4.
It's easier to read separate functions for crtc and plane scaler state.
Changes since v1:
- Update documentation.
Changes since v2:
- Get rid of parameters to skl_update_scaler only used for traces.
This avoids needing to document the other parameters.
Changes since v3:
- Rename scaler_idx to scaler_user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of a whole lot of ternary operators and assign the index
in scaler_id, instead of the id. They're the same thing.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit has two main advantages: simplify intel_fbc_update()
and deduplicate the strings.
v2:
- Rebase due to changes on P1.
- set_no_fbc_reason() can now return void (Chris).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently intel_gen4_compute_page_offset() simply picks the closest
page boundary below the linear offset. That however may not be suitably
aligned to satisfy any hardware specific restrictions. So let's make
sure the page boundary we choose is properly aligned.
Also to play it a bit safer lets split the remaining linear offset into
x and y values instead of just x. This should make no difference for
most platforms since we convert the x and y offsets back into a linear
offset before feeding them to the hardware. HSW+ are different however
and use x and y offsets even with linear buffers, so they might have
trouble if either the x or y get too big.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 3bae26eb2991c00670df377cf6c3bc2b0577e82a.
Seems it introduces regressions for 3 different reasons, oh boy..
In bug #90868 as I can see the atomic state will be restored on
resume without the planes being set up properly. Because plane
setup here requires the atomic state, we'll have to settle
for committing atomic planes first.
In bug #90861 the failure appears to affect mostly DP devices,
and happens because reading out the atomic state prevents a modeset
on boot, which would require better hw state readout.
In bug #90874 it's shown that cdclk should be part of the atomic
state, so only performing a single modeset during resume excarbated
the issue.
It's better to fix those issues first, and then commit this patch,
so do that temporarily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.
We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.
It's required to revert this commit to revert the atomic hw
state readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This needs to be done last after all modesets have been calculated.
A modeset first disables all crtc's, so any crtc that undergoes a
modeset counts as inactive.
If no modeset's done, or > 1 crtc's stay w/a doesn't apply.
Apply workaround on the first crtc if 1 crtc stays active.
Apply workaround on the second crtc if no crtc was active.
Changes since v1:
- Use intel_crtc->atomic as a place to put hsw_workaround_pipe.
- Make sure quirk only applies to haswell.
- Use first loop to iterate over newly enabled crtc's only.
This increases readability.
Changes since v2:
- Move hsw_workaround_pipe back to crtc_state.
Changes since v3:
- Return errors from haswell_mode_set_planes_workaround.
Changes since v4:
- Clean up commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Calling intel_set_mode will cause intel_display_set_init_power to be
called, make sure init_power gets set again afterwards.
Changes since v1:
- Fix to compile with v2 of the patch that adds intel_display_suspend.
- Add intel_display_set_init_power.
- Set return value to int to allow error checking.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Assume the callers lock everything with drm_modeset_lock_all.
This change had to be done after converting suspend/resume to
use atomic_state so the atomic state is preserved, otherwise
all transitional state is erased.
Now all callers of .crtc_enable and .crtc_disable go through
atomic modeset! :-D
Changes since v1:
- Only check for crtc_state->active in valleyview_modeset_global_pipes.
- Only check for crtc_state->active in modeset_update_crtc_power_domains.
Changes since v2:
- Rework on top of the changed patch order.
Changes since v3:
- Rename intel_crtc_toggle in description to *_control
- Change return value to int.
- Do not add plane state, should be done implicitly already.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To make this work we load the new hardware state into the
atomic_state, then swap it with the sw state.
This lets us change the force restore path in setup_hw_state()
to use a single call to intel_mode_set() to restore all the
previous state.
As a nice bonus this kills off encoder->new_encoder,
connector->new_enabled and crtc->new_enabled. They were used only
to restore the state after a modeset.
Changes since v1:
- Make sure all possible planes are added with their crtc set,
so they will be turned off on first modeset.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we can subclass drm_atomic_state we can also use it to keep
track of all the pll settings. atomic_state is a better place to hold
all shared state than keeping pll->new_config everywhere.
Changes since v1:
- Assert connection_mutex is held.
Changes since v2:
- Fix swapped arguments to kzalloc for intel_atomic_state_alloc. (Jani Nikula)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Having a single path for everything makes it a lot easier to keep
crtc_state->active in sync with intel_crtc->active.
A crtc cannot be changed to active when not enabled, because it means
no mode is set and no connectors are connected.
This should also make intel_crtc->active match crtc_state->active.
Changes since v1:
- Reworded commit message, there's no intel_crtc_toggle.
Changes since v2:
- Change some callers of intel_crtc_control to intel_display_suspend.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a function used to disable all crtc's. This makes it clearer
to distinguish between when mode needs to be preserved and when
it can be trashed.
Changes since v1:
- Copy power changes from intel_crtc_control.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the pll updates are staged the put_shared_dpll function
consists only of checks that are done in check_shared_dpll_state
after a modeset too.
The changes to pll->config are overwritten by
intel_shared_dpll_commit, so this entire function is a noop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.
There's no similar restriction listed for HSW, so leave that one alone
for now.
v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The primary plane frobbing was removed from the sprite code in
commit ecce87ea3a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:50 2015 +0300
drm/i915: Remove implicitly disabling primary plane for now
but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.
The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.
This allows intel_flush_primary_plane() to be killed off.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.
The bugs stems from removing the seqno checking in
commit 536f5b5e86
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Thu Nov 6 11:03:40 2014 +0200
drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake nv12 format requires dbuf (aka. ddb) calculations
and programming for each of y and uv sub-planes. Made minor
changes to reuse current dbuf calculations and programming
for uv plane. i.e., with this change, existing computation
is used for either packed format or uv portion of nv12
depending on incoming format. Added new code for dbuf
computation and programming for y plane.
This patch is a pre-requisite for adding NV12 format support.
Actual nv12 support is coming in later patches.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently vlv_wait_port_ready() waits for all four lanes on the
appropriate channel. This no longer works on CHV when the unused
lanes may be power gated. So pass in a mask of lanes that the
caller is expecting to be ready.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
