Use the correct compatible for the new protocol used by the firmware
on the touch controller, the GPIO wakeup isn't used in that case.
Also eGalax touch needs axis swapping, just as with the RMI4 touch.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the imx6qdl-zii-rdu2 board the RTC functionality is provided via
a DS1341 RTC connected via I2C bus, so we can safely disable the internal
one.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlt+NecPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3ScQQAIic6NPWiqGEwTRN1I+WoyoCt8oTGgiiu1kf
h23RaLWI+TaEpR1yg5ko6wGlxlvBG1C/u2sOc0lD9nSt9JQ3evXXwMQ0bUNhKdSE
8z3jhpnJYu5iNDsB15XfznhivpjOQUQNQXPR1/PG9j6SCKgdWi6wYR+A+q98Pe9d
otzMizQOY0QUMYAec20Zvzgfs+AvEtOAo/w5K4tRb+Fv/EVixV8bVeT4uykxunFt
6xOM0Ssvnwo3AnEh+V+FjAL8khMC7A3JC+/emXqqcw1Ogdg/GSnxriL7v6LchcwH
fvYb8hujQCcZ0+mlN0W214RkWd1xAc0CwJ0JdKw/RMnskty5u5B7gXcDyZFw1oJ7
b7Uof7N8l12lsXTqWW8CKOHupI1gxYshi0QJzkgkfY6P3h8ntE8HJhhcgjcHE0AN
3mMjhzbDGjfUykVgS2rFpR6tm3JHT13jDl88jhAT+xtuYYxy60nqPBM9MD6jIzjF
BnIVJBNX3sYa7aheEnZFBuA/Af/05fKbpUVQTNwnfq2f6NYDAbF9iBkCHepudZBa
0U+tNHuDlVXwLXoocE1Nac5IJgPiuX2bsuJ9xHKLXb6hMr9L4YtPOaKwDaJb1hTZ
XIHhlrF9w0ig9gu3IxaE+rC3hfu965CeFws0kwSZ9l52xmSP0Yi22ebSTfP6+h+u
XLyOhpp8
=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f64992d1a9 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unnecessary #address-cells/#size-cells from the switch nodes
to fix the following DTC warnings:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This touchscreen is present instead of the RMI4 touch on some SKUs of
the RDU2. Keep it disabled by default, the bootloader will enable it
instead of the RMI4 touch when running on one of those units.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This bumps the SoC/PU domain operating points by 25mV, giving a total
of 75mV margin to the minimum required voltages. This gets rid of
brown-outs seen due to voltage drop-out on the board.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The system has an external watchdog in the environment processor
so the internal watchdog is of no use.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: cphealy@gmail.com
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
device_type = "pci" should be used for the SoC level PCI controller and
it is already present at imx6qdl.dtsi.
Remove it from the subnode in order to fix the following build
warnings with W=1:
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing bus-range for PCI bridge
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (unit_address_format): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is needed for the bootloader to patch in the correct MAC address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ7ypUAAoJEFBXWFqHsHzOpVkH/RsZ3IMg8O5tMO6uz1CNmutR
3EAXfBeQTnQZe2A/3XkDRpJWGiIniRSVAf6rYipmeyV9jV2Ff4vfiv5gnhg1ev+B
eV35W3gb3EclHKrHgHVMkfzWfNp63L1etdVFrY0QuMc0wQbch0TwO3TTPHpk0+AS
eauLOMY1qzRVnayzZ8IeTn++igsoj4KT1NmIprNKe66eDAOfWxO0IB26r0svKrhg
mIlqTUG1p6I/H8h6hQZuRJaLM9no3dHDcm7Scbf1y8Mvf5mPVTTHKXGLLyEVT/UB
SEWydfAt0VEAEA+Uk6pFJsrG1KRx0hwF46DHk2BXj7A1wxBsUIPnMSoMRWgGrZE=
=grKK
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.15" from Shawn Guo:
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
ARM: dts: imx53-tx53: fix interrupt flags
ARM: dts: imx28-tx28: fix interrupt flags
ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
ARM: dts: imx: add ZII RDU1 board
ARM: dts: imx: add support for TX6 modules on MB7 baseboard
ARM: dts: imx: add support for TX6QP
ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
ARM: dts: imx6-tx6: move display configuration to .dtsi file
ARM: dts: imx6-tx6: add support for I2C bus recovery
ARM: dts: imx6-tx6: convert to using simple-audio-card
ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
ARM: dts: imx6-tx6: add trickle-charge config for DS1339
ARM: dts: imx6-tx6: remove obsolete ipu1 alias
ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
...
[arnd: made sure we have no new leading zeroes in unit address during merge]
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is causing issues with some specific controller configurations, as
the platform isn't power limited it's better to keep it disabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Just like the OTG port, USB H1 has no over-current detection wired up.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Micrel PHY has its interrupt pin connected to a GPIO line. Wire
this up in the device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Marvell switch has its interrupt pin connected to a GPIO
line. Wire this up in the device tree. This then allows us to use
interrupts from the embedded Ethernet PHYs in the switch. Also wire
them up in device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Marvell switch has an EEPROM connected to it. List the size in DT,
in order to enable access to it via ethtool.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RDU2 has a Marvell 88E6352 switch. Both the FEC and the i210
Ethernet interfaces are connected to the switch. Make the FEC the DSA
"CPU" port, and the i210 as a regular port on the switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FEC has a Micrel PHY connected to it. This PHY is managed using
the bit-banging MDIO bus. Add this to the device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the Zodiac Inflight Innovations RDU2 board,
which has both a Quad and a QuadPlus variant.
The board supports different panels, with the bootloader patching
in the correct compatible, depending on the hardware configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
