The TWT Information Frame Disabled bit of control field of TWT Setup
frame shall be set to 1 since handling TWT Information frame is not
supported by current mac80211 implementation.
Fixes: f5a4c24e68 ("mac80211: introduce individual TWT support in AP mode")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Link: https://lore.kernel.org/r/20221027015653.1448-1-howard-yh.hsu@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to transmit an data frame with tx_status to a destination
that have no route in the mesh, then it is dropped without recrediting
the ack_status_frames idr.
Once it is exhausted, wpa_supplicant starts failing to do SAE with
NL80211_CMD_FRAME and logs "nl80211: Frame command failed".
Use ieee80211_free_txskb() instead of kfree_skb() to fix it.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20221027140133.1504-1-nicolas.cavallari@green-communications.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When device is running and the interface status is changed, the gpf issue
is triggered. The problem triggering process is as follows:
Thread A: Thread B
ieee80211_runtime_change_iftype() process_one_work()
... ...
ieee80211_do_stop() ...
... ...
sdata->bss = NULL ...
... ieee80211_subif_start_xmit()
ieee80211_multicast_to_unicast
//!sdata->bss->multicast_to_unicast
cause gpf issue
When the interface status is changed, the sending queue continues to send
packets. After the bss is set to NULL, the bss is accessed. As a result,
this causes a general-protection-fault issue.
The following is the stack information:
general protection fault, probably for non-canonical address
0xdffffc000000002f: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000178-0x000000000000017f]
Workqueue: mld mld_ifc_work
RIP: 0010:ieee80211_subif_start_xmit+0x25b/0x1310
Call Trace:
<TASK>
dev_hard_start_xmit+0x1be/0x990
__dev_queue_xmit+0x2c9a/0x3b60
ip6_finish_output2+0xf92/0x1520
ip6_finish_output+0x6af/0x11e0
ip6_output+0x1ed/0x540
mld_sendpack+0xa09/0xe70
mld_ifc_work+0x71c/0xdb0
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Reported-by: syzbot+c6e8fca81c294fd5620a@syzkaller.appspotmail.com
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221026063959.177813-1-shaozhengchao@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_register_hw free the allocated cipher suites when
registering wiphy fail, and ieee80211_free_hw will re-free it.
set wiphy_ciphers_allocated to false after freeing allocated
cipher suites.
Signed-off-by: taozhang <taozhang@bestechnic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----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=M+mV
-----END PGP SIGNATURE-----
Merge tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
The prandom_bytes() function has been a deprecated inline wrapper around
get_random_bytes() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. This was done as a basic find and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # powerpc
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
If beacon protection is active but the beacon cannot be
decrypted or is otherwise malformed, we call the cfg80211
API to report this to userspace, but that uses a netdev
pointer, which isn't present for P2P-Device. Fix this to
call it only conditionally to ensure cfg80211 won't crash
in the case of P2P-Device.
This fixes CVE-2022-42722.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaf183af7 ("mac80211: Report beacon protection failures to user space")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we parse a multi-BSSID element, we might point some
element pointers into the allocated nontransmitted_profile.
However, we free this before returning, causing UAF when the
relevant pointers in the parsed elements are accessed.
Fix this by not allocating the scratch buffer separately but
as part of the returned structure instead, that way, there
are no lifetime issues with it.
The scratch buffer introduction as part of the returned data
here is taken from MLO feature work done by Ilan.
This fixes CVE-2022-42719.
Fixes: 5023b14cf4 ("mac80211: support profile split between elements")
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Per spec, the maximum value for the MaxBSSID ('n') indicator is 8,
and the minimum is 1 since a multiple BSSID set with just one BSSID
doesn't make sense (the # of BSSIDs is limited by 2^n).
Limit this in the parsing in both cfg80211 and mac80211, rejecting
any elements with an invalid value.
This fixes potentially bad shifts in the processing of these inside
the cfg80211_gen_new_bssid() function later.
I found this during the investigation of CVE-2022-41674 fixed by the
previous patch.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Properly handle TX stop for internal queues (iTXQs) within mac80211.
mac80211 must not stop netdev queues when using mac80211 iTXQs.
For these drivers the netdev interface is created with IFF_NO_QUEUE.
While netdev still drops frames for IFF_NO_QUEUE interfaces when we stop
the netdev queues, it also prints a warning when this happens:
Assuming the mac80211 interface is called wlan0 we would get
"Virtual device wlan0 asks to queue packet!" when netdev has to drop a
frame.
This patch is keeping the harmless netdev queue starts for iTXQ drivers.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since AP_VLAN interfaces are not passed to the driver, check offload_flags
on the bss vif instead.
Reported-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Fixes: 80a915ec44 ("mac80211: add rx decapsulation offload support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unlock before returning -EOPNOTSUPP.
Fixes: 3c06e91b40 ("wifi: mac80211: Support POWERED_ADDR_CHANGE feature")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At some point a few kernel debug prints started appearing which
indicated something was sending invalid IEs:
"bad VHT capabilities, disabling VHT"
"Invalid HE elem, Disable HE"
Turns out these were being printed because the local hardware
supported HE/VHT but the peer/AP did not. Bad/invalid indicates,
to me at least, that the IE is in some way malformed, not missing.
For the HE print (ieee80211_verify_peer_he_mcs_support) it will
now silently fail if the HE capability element is missing (still
prints if the element size is wrong).
For the VHT print, it has been removed completely and will silently
set the DISABLE_VHT flag which is consistent with how DISABLE_HT
is set.
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building the probe request IEs HE support is checked for
the 6GHz band (wiphy->bands[NL80211_BAND_6GHZ]). If supported
the HE capability IE should be included according to the spec.
The problem is the 16-bit capability is obtained from the
band object (sband) that was passed in, not the 6GHz band
object (sband6). If the sband object doesn't support HE it will
result in a warning.
Fixes: 7d29bc50b3 ("mac80211: always include HE 6GHz capability in probe request")
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since STP TCN frames are only 7 bytes, the pskb_may_pull call returns an error.
Instead of dropping those packets, bump them back to the slow path for proper
processing.
Fixes: 49ddf8e6e2 ("mac80211: add fast-rx path")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
* refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
* support CYW43439 SDIO chipset
* support BCM4378 on Apple platforms
* support CYW89459 PCIe chipset
rtw89
* more work to get rtw8852c supported
* P2P support
* support for enabling and disabling MSDU aggregation via nl80211
mt76
* tx status reporting improvements
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmM3BGYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuR3Af/XiuMlnDB6flq+M/kQHLWWvHybLw5aCJ7
l3yXhNFWxpBl2hQXtj17JSjVCYQmxbfrgRqhbNhyACO25bpymCb5QctB9X+Y7TwL
250JmuKvQfFx5oJNRfJ67dKTf3raloQYbdEMJNqySgebL+eSfrDskc9vaCLVDmCK
I994fl0Q1wUbJ6fbuIFd07ti8ay6UlSS/iakv4+nEeimabtZWJWlXBWYRpKpikdP
h9z2kPtss6yz6seaQuw6ny+qysYLi11Tp+Cued9XR3dWOOhB2X1tLHH0H02xPw76
9OJZEJHycP2juxjMfAaktHY+VX36GPLsMLUTVusH0h/Fdy3VG8YSAw==
=emmG
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pskb_may_pull already contains all of the checks performed by
pskb_pull.
Use pskb_may_pull for validation in pskb_pull, eliminating the
duplication and making __pskb_pull obsolete.
Replace __pskb_pull with pskb_pull where applicable.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6911458dc4 ("wifi: mac80211: mlme: refactor assoc success
handling") moved the per-link setup out of ieee80211_assoc_success() into a
new function ieee80211_assoc_config_link() but missed to remove the unlock
of 'sta_mtx' in case of HE capability/operation missing on HE AP, which
leads to a double unlock:
ieee80211_assoc_success() {
...
ieee80211_assoc_config_link() {
...
if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
(!elems->he_cap || !elems->he_operation)) {
mutex_unlock(&sdata->local->sta_mtx);
...
}
...
}
...
mutex_unlock(&sdata->local->sta_mtx);
...
}
Fixes: 6911458dc4 ("wifi: mac80211: mlme: refactor assoc success handling")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Link: https://lore.kernel.org/r/20220925143420.784975-1-rafaelmendsr@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 98b0b46746 ("wifi: mac80211: mlme: use correct link_sta")
switched to link station instead of deflink and added some checks to do
that, which are done with the 'sta_mtx' mutex held. However, the error
path of these checks does not unlock 'sta_mtx' before returning.
Fixes: 98b0b46746 ("wifi: mac80211: mlme: use correct link_sta")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Link: https://lore.kernel.org/r/20220924184042.778676-1-rafaelmendsr@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During our testing of WFM200 module over SDIO on i.MX6Q-based platform,
we discovered a memory corruption on the system, tracing back to the wfx
driver. Using kfence, it was possible to trace it back to the root
cause, which is hw->max_rates set to 8 in wfx_init_common,
while the maximum defined by IEEE80211_TX_TABLE_SIZE is 4.
This causes array out-of-bounds writes during updates of the rate table,
as seen below:
BUG: KFENCE: memory corruption in kfree_rcu_work+0x320/0x36c
Corrupted memory at 0xe0a4ffe0 [ 0x03 0x03 0x03 0x03 0x01 0x00 0x00
0x02 0x02 0x02 0x09 0x00 0x21 0xbb 0xbb 0xbb ] (in kfence-#81):
kfree_rcu_work+0x320/0x36c
process_one_work+0x3ec/0x920
worker_thread+0x60/0x7a4
kthread+0x174/0x1b4
ret_from_fork+0x14/0x2c
0x0
kfence-#81: 0xe0a4ffc0-0xe0a4ffdf, size=32, cache=kmalloc-64
allocated by task 297 on cpu 0 at 631.039555s:
minstrel_ht_update_rates+0x38/0x2b0 [mac80211]
rate_control_tx_status+0xb4/0x148 [mac80211]
ieee80211_tx_status_ext+0x364/0x1030 [mac80211]
ieee80211_tx_status+0xe0/0x118 [mac80211]
ieee80211_tasklet_handler+0xb0/0xe0 [mac80211]
tasklet_action_common.constprop.0+0x11c/0x148
__do_softirq+0x1a4/0x61c
irq_exit+0xcc/0x104
call_with_stack+0x18/0x20
__irq_svc+0x80/0xb0
wq_worker_sleeping+0x10/0x100
wq_worker_sleeping+0x10/0x100
schedule+0x50/0xe0
schedule_timeout+0x2e0/0x474
wait_for_completion+0xdc/0x1ec
mmc_wait_for_req_done+0xc4/0xf8
mmc_io_rw_extended+0x3b4/0x4ec
sdio_io_rw_ext_helper+0x290/0x384
sdio_memcpy_toio+0x30/0x38
wfx_sdio_copy_to_io+0x88/0x108 [wfx]
wfx_data_write+0x88/0x1f0 [wfx]
bh_work+0x1c8/0xcc0 [wfx]
process_one_work+0x3ec/0x920
worker_thread+0x60/0x7a4
kthread+0x174/0x1b4
ret_from_fork+0x14/0x2c 0x0
After discussion on the wireless mailing list it was clarified
that the issue has been introduced by:
commit ee0e16ab75 ("mac80211: minstrel_ht: fill all requested rates")
and fix shall be in minstrel_ht_update_rates in rc80211_minstrel_ht.c.
Fixes: ee0e16ab75 ("mac80211: minstrel_ht: fill all requested rates")
Link: https://lore.kernel.org/all/12e5adcd-8aed-f0f7-70cc-4fb7b656b829@camlingroup.com/
Link: https://lore.kernel.org/linux-wireless/20220915131445.30600-1-lech.perczak@camlingroup.com/
Cc: Jérôme Pouiller <jerome.pouiller@silabs.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Seiderer <ps.report@gmx.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Krzysztof Drobiński <krzysztof.drobinski@camlingroup.com>,
Signed-off-by: Paweł Lenkow <pawel.lenkow@camlingroup.com>
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Peter Seiderer <ps.report@gmx.net>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
changed ieee80211_tx_control_port() to aways call
__ieee80211_select_queue() without checking local->hw.queues.
__ieee80211_select_queue() returns a queue-id between 0 and 3, which means
that now ieee80211_tx_control_port() may end up setting the queue-mapping
for a skb to a value higher then local->hw.queues if local->hw.queues
is less then 4.
Specifically this is a problem for ralink rt2500-pci cards where
local->hw.queues is 2. There this causes rt2x00queue_get_tx_queue() to
return NULL and the following error to be logged: "ieee80211 phy0:
rt2x00mac_tx: Error - Attempt to send packet over invalid queue 2",
after which association with the AP fails.
Other callers of __ieee80211_select_queue() skip calling it when
local->hw.queues < IEEE80211_NUM_ACS, add the same check to
ieee80211_tx_control_port(). This fixes ralink rt2500-pci and
similar cards when less then 4 tx-queues no longer working.
Fixes: 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
Cc: Markus Theil <markus.theil@tu-ilmenau.de>
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220918192052.443529-1-hdegoede@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure local->queue_stop_reasons and vif.txqs_stopped stay in sync.
When a new vif is created the queues may end up in an inconsistent state
and be inoperable:
Communication not using iTXQ will work, allowing to e.g. complete the
association. But the 4-way handshake will time out. The sta will not
send out any skbs queued in iTXQs.
All normal attempts to start the queues will fail when reaching this
state.
local->queue_stop_reasons will have marked all queues as operational but
vif.txqs_stopped will still be set, creating an inconsistent internal
state.
In reality this seems to be race between the mac80211 function
ieee80211_do_open() setting SDATA_STATE_RUNNING and the wake_txqs_tasklet:
Depending on the driver and the timing the queues may end up to be
operational or not.
Cc: stable@vger.kernel.org
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220915130946.302803-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_txq_purge() calls fq_tin_reset() and
ieee80211_purge_tx_queue(); Both are then calling
ieee80211_free_txskb(). Which can decide to TX the skb again.
There are at least two ways to get a deadlock:
1) When we have a TDLS teardown packet queued in either tin or frags
ieee80211_tdls_td_tx_handle() will call ieee80211_subif_start_xmit()
while we still hold fq->lock. ieee80211_txq_enqueue() will thus
deadlock.
2) A variant of the above happens if aggregation is up and running:
In that case ieee80211_iface_work() will deadlock with the original
task: The original tasks already holds fq->lock and tries to get
sta->lock after kicking off ieee80211_iface_work(). But the worker
can get sta->lock prior to the original task and will then spin for
fq->lock.
Avoid these deadlocks by not sending out any skbs when called via
ieee80211_free_txskb().
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20220915124120.301918-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement an API function and debugfs file to switch
active links.
Also provide an async version of the API so drivers
can call it in arbitrary contexts, e.g. while in the
authorized callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add macros (and an exported function) to allow checking some
link RCU protected accesses that are happening in callbacks
from mac80211 and are thus under the correct lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a link_id parameter to ieee80211_nullfunc_get() to be
able to obtain a correctly addressed frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new API function ieee80211_find_sta_by_link_addrs()
that looks up the STA and link ID based on interface and
station link addresses.
We're going to use it for mac80211-hwsim to track on the
AP side which links are active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let the driver select active links and properly
make multi-link connections, as a first step isolate the
driver from inactive links, and set the active links to be
only the association link for client-side interfaces. For
AP side nothing changes since APs always have to have all
their links active.
To simplify things, update the for_each_sta_active_link()
API to include the appropriate vif pointer.
This also implies not allocating a chanctx for an inactive
link, which requires a few more changes.
Since we now no longer try to program multiple links to the
driver, remove the check in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use rx->link_sta everywhere instead of accessing the default link.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have a link_sta pointer in the rx struct
we also need to fill it in all the cases. It didn't
matter so much until now as we weren't using it, but
the code should really be able to assume that if the
rx.sta is set, so is rx.link_sta.
Fixes: ccdde7c74f ("wifi: mac80211: properly implement MLO key handling")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- rtw89: large update across the map, e.g. coex, pci(e), etc.
- ath9k: uninit memory read fix
- ath10k: small peer map fix and a WCN3990 device fix
- wfx: underflow
stack
- the "change MAC address while IFF_UP" change from James
we discussed
- more MLO work, including a set of fixes for the previous
code, now that we have more code we can exercise it more
- prevent some features with MLO that aren't ready yet
(AP_VLAN and 4-address connections)
-----BEGIN PGP SIGNATURE-----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=7imA
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
drivers
- rtw89: large update across the map, e.g. coex, pci(e), etc.
- ath9k: uninit memory read fix
- ath10k: small peer map fix and a WCN3990 device fix
- wfx: underflow
stack
- the "change MAC address while IFF_UP" change from James
we discussed
- more MLO work, including a set of fixes for the previous
code, now that we have more code we can exercise it more
- prevent some features with MLO that aren't ready yet
(AP_VLAN and 4-address connections)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix DMA from stack in wilc1000 driver
- fix crash on chip reset failure in mt7921e
- fix for the reported warning on aggregation timer expiry
- check packet lengths in hwsim virtio paths
- fix compiler warnings/errors with AAD construction by
using struct_group
- fix Intel 4965 driver rate scale operation
- release channel contexts correctly in mac80211 mlme code
-----BEGIN PGP SIGNATURE-----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=GyC3
-----END PGP SIGNATURE-----
Merge tag 'wireless-2022-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes berg says:
====================
We have a handful of fixes:
- fix DMA from stack in wilc1000 driver
- fix crash on chip reset failure in mt7921e
- fix for the reported warning on aggregation timer expiry
- check packet lengths in hwsim virtio paths
- fix compiler warnings/errors with AAD construction by
using struct_group
- fix Intel 4965 driver rate scale operation
- release channel contexts correctly in mac80211 mlme code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, other paths calling drv_sta_state() hold the mutex
and therefore drivers can assume that, and look at links with
that protection. Fix that for the reconfig path as well; to
do it more easily use ieee80211_reconfig_stations() for the
AP/AP_VLAN station reconfig as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we stop a not-yet-started scan, we erroneously call
into the driver, causing a sequence of sw_scan_start()
followed by sw_scan_complete() twice. This will cause a
warning in hwsim with next in line commit that validates
the address passed to wmediumd/virtio. Fix this by doing
the calls only if we were actually scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Right now, we assign the link address only after we add
the link to the driver, which is quite obviously wrong.
It happens to work in many cases because it gets updated
immediately, and then link_conf updates may update it,
but it's clearly not really right.
Set the link address during ieee80211_mgd_setup_link()
so it's set before telling the driver about the link.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We probably should've done that originally, we already have
about 300 lines of code there, and will add more. Move all
the link code we wrote to a new file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need the sdata argument, and it doesn't make any
sense for a direct conversion from one value to another,
so just remove the argument
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adds support in mac80211 for NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE.
The motivation behind this functionality is to fix limitations of
address randomization on frequencies which are disallowed in world
roaming.
The way things work now, if a client wants to randomize their address
per-connection it must power down the device, change the MAC, and
power back up. Here lies a problem since powering down the device
may result in frequencies being disabled (until the regdom is set).
If the desired BSS is on one such frequency the client is unable to
connect once the phy is powered again.
For mac80211 based devices changing the MAC while powered is possible
but currently disallowed (-EBUSY). This patch adds some logic to
allow a MAC change while powered by removing the interface, changing
the MAC, and adding it again. mac80211 will advertise support for
this feature so userspace can determine the best course of action e.g.
disallow address randomization on certain frequencies if not
supported.
There are certain limitations put on this which simplify the logic:
- No active connection
- No offchannel work, including scanning.
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
