As far as I can tell CONFIG_CPM is the right symbol to use to
conditionally compile the cpm-serial.c code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only build the OPAL console code in when necessary. This looks like it
should use CONFIG_PPC_POWERNV, but because the opal-call.S code is
64-bit only, we must only build it when we're building the boot
wrapper 64-bit.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The serial code in uartlite.c only matches if we find one of two
Xilinx (xlnx) nodes in the device tree, there's no need to build or
link the code on other platforms.
As far as I can tell CONFIG_XILINX_VIRTEX is the appropriate symbol to
use to conditionally compile the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
mpsc.c and mpc52xx-psc.c are platform-specific serial drivers, and
should be compiled for the respective platforms only.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds an OPAL console backend to the powerpc boot wrapper so
that decompression failures inside the wrapper can be reported to the
user. This is important since it typically indicates data corruption in
the firmware and other nasty things.
Currently this only works when building a little endian kernel. When
compiling a 64 bit BE kernel the wrapper is always build 32 bit to be
compatible with some 32 bit firmwares. BE support will be added at a
later date. Another limitation of this is that only the "raw" type of
OPAL console is supported, however machines that provide a hvsi console
also provide a raw console so this is not an issue in practice.
Actually-written-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Move #ifdef __powerpc64__ to avoid warnings on 32-bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On some platforms a 5 second timeout during boot might be quite long, so
make it configurable. Run the loop at least once to let the user stop
the boot by holding a key pressed. If the timeout is set to 0, don't
wait for input, which can be used as a workaround if the boot hangs on
random data coming in on the serial port.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
[mpe: Changelog wording & whitespace]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds the bootwrapper for the cuImage target and a compatible property
check for "pnpPNP,501" to the generic serial console support code.
The default link address for the cuImage target is set to 0x800000. This
allows to boot the kernel with AmigaOS4's second level bootloader, which
always loads a uImage at 0x500000.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Missed this one in the boot loader before.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allows the bootwrapper to use the uartlite device for console output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This serial port is used on all 8xx, many 82xx, and some 85xx chips.
The driver requires that the port has already been set up by the firmware
and/or platform code.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
1. Search the entire compatible list for serial devices.
The serial code previously did a simple strcmp on the compatible
node; this fails when the match string is not the first compatible
listed. Use dt_is_compatible() instead.
2. Don't call serial_edit_cmdline if getc isn't defined.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes the constantness of the powerpc bootwrapper's console_ops.write
routine. Allows printing of constant strings.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console. This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add serial console support for non-OF systems. There is a generic serial
console layer which calls a serial console driver. Included is the serial
console driver for the ns16550 class of uarts. Necessary support routines
are added as well.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
