Use __flush_invalidate_dcache_page_alias with alias set to color of the
page physical address instead of __flush_invalidate_dcache_page: this
works for high memory pages and mapping/unmapping to the TLBTEMP area is
virtually free.
Allow building configurations with aliasing cache and highmem enabled.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Define ARCH_PKMAP_COLORING and provide corresponding macro definitions
on cores with aliasing data cache.
Instead of single last_pkmap_nr maintain an array last_pkmap_nr_arr of
pkmap counters for each page color. Make sure that kmap maps physical
page at virtual address with color matching its physical address.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Map high memory pages at virtual addresses with color that match color
of their physical address. Existing cache alias management mechanisms
may be used with such pages.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Existing clear_user_page and copy_user_page cannot be used with highmem
because they calculate physical page address from its virtual address
and do it incorrectly in case of high memory page mapped with
kmap_atomic. Also kmap is not needed, as most likely userspace mapping
color would be different from the kmapped color.
Provide clear_user_highpage and copy_user_highpage functions that
determine if temporary mapping is needed for the pages. Move most of the
logic of the former clear_user_page and copy_user_page to
xtensa/mm/cache.c only leaving temporary mapping setup, invalidation and
clearing/copying in the xtensa/mm/misc.S. Rename these functions to
clear_page_alias and copy_page_alias.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
To support aliasing cache both kmap region sizes are multiplied by the
number of data cache colors. After that expansion page tables that cover
kmap regions may become larger than one page. Correctly allocate and
initialize page tables in this case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
It's much easier to reason about alignment and coloring of regions
located in the fixmap when fixmap index is just a PFN within the fixmap
region. Change fixmap addressing so that index 0 corresponds to
FIXADDR_START instead of the FIXADDR_TOP.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
When sysmem reservation occurs exactly at the end of an existing block
that block is deleted, because it is incorrectly included in the range
of memblocks to remove. Fix that by skipping such block.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Introduce fixmap area just below the vmalloc region. Use it for atomic
mapping of high memory pages.
High memory on cores with cache aliasing is not supported and is still
to be implemented. Fail build for such configurations for now.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Debug dump of physical memory configuration. Useful for inspection of
resulting memory map, esp. in the presence of memmap= kernel option.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This option is useful for reserving memory regions for secondary cores
in AMP configurations.
Implement the following memmap variants:
- memmap=nn[KMG]@ss[KMG]: force usage of a specific region of memory;
- memmap=nn[KMG]$ss[KMG]: mark specified memory as reserved;
- memmap=nn[KMG]: set end of memory.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Bootparam meminfo is a bootloader ABI, kernel meminfo is for the kernel
bookkeeping, keep them separate. Kernel doesn't care of memory region
types, so drop the type field and don't pass it to add_sysmem_bank.
Move kernel sysmem structures and prototypes to asm/sysmem.h and sysmem
variable and add_sysmem_bank to mm/init.c
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- allow booting xtfpga on boards with new uBoot and >128MBytes memory;
- drop nonexistent GPIO32 support from fsf variant;
- don't select USE_GENERIC_SMP_HELPERS;
- enable common clock framework support, set up ethoc clock on xtfpga;
- wire up sched_setattr and sched_getattr syscalls.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XS4m
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20140221-1' into for_next
Xtensa fixes for 3.14:
- allow booting xtfpga on boards with new uBoot and >128MBytes memory;
- drop nonexistent GPIO32 support from fsf variant;
- don't select USE_GENERIC_SMP_HELPERS;
- enable common clock framework support, set up ethoc clock on xtfpga;
- wire up sched_setattr and sched_getattr syscalls.
Signed-off-by: Chris Zankel <chris@zankel.net>
Use the simple-bus node to discover the io area, and remap the cached and
bypass io ranges. The parent-bus-address value of the first triplet in the
"ranges" property is used. This value is rounded down to the nearest 256MB
boundary. The length of the io area is fixed at 256MB; the "ranges" property
length value is ignored.
Other limitations: (1) only the first simple-bus node is considered, and (2)
only the first triplet of the "ranges" property is considered.
See ePAPR 1.1 §6.5 for the simple-bus node description, and §2.3.8 for the
"ranges" property description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This is largely based on SMP code from the xtensa-2.6.29-smp tree by
Piet Delaney, Marc Gauthier, Joe Taylor, Christian Zankel (and possibly
other Tensilica folks).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
This fixes the following build warnings:
arch/xtensa/mm/misc.S: Assembler messages:
arch/xtensa/mm/misc.S:143: Warning: value 0xffffffff30000106 truncated to 0x30000106
arch/xtensa/mm/misc.S:197: Warning: value 0xffffffff30000106 truncated to 0x30000106
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
At the moment xtensa uses slab allocator for PTE table. It doesn't work
with enabled split page table lock: slab uses page->slab_cache and
page->first_page for its pages. These fields share stroage with
page->ptl.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike global OOM handling, memory cgroup code will invoke the OOM killer
in any OOM situation because it has no way of telling faults occuring in
kernel context - which could be handled more gracefully - from
user-triggered faults.
Pass a flag that identifies faults originating in user space from the
architecture-specific fault handlers to generic code so that memcg OOM
handling can be improved.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- check that user TLB mappings correspond to the current page table;
- check that TLB mapping VPN is in the kernel/user address range
in accordance with its ASID.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Concentrate code to modify totalram_pages into the mm core, so the arch
memory initialized code doesn't need to take care of it. With these
changes applied, only following functions from mm core modify global
variable totalram_pages: free_bootmem_late(), free_all_bootmem(),
free_all_bootmem_node(), adjust_managed_page_count().
With this patch applied, it will be much more easier for us to keep
totalram_pages and zone->managed_pages in consistence.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Address more review comments from last round of code review.
1) Enhance free_reserved_area() to support poisoning freed memory with
pattern '0'. This could be used to get rid of poison_init_mem()
on ARM64.
2) A previous patch has disabled memory poison for initmem on s390
by mistake, so restore to the original behavior.
3) Remove redundant PAGE_ALIGN() when calling free_reserved_area().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change signature of free_reserved_area() according to Russell King's
suggestion to fix following build warnings:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:603:2: warning: passing argument 1 of 'free_reserved_area' makes integer from pointer without a cast [enabled by default]
free_reserved_area(__va(PHYS_PFN_OFFSET), swapper_pg_dir, 0, NULL);
^
In file included from include/linux/mman.h:4:0,
from arch/arm/mm/init.c:15:
include/linux/mm.h:1301:22: note: expected 'long unsigned int' but argument is of type 'void *'
extern unsigned long free_reserved_area(unsigned long start, unsigned long end,
mm/page_alloc.c: In function 'free_reserved_area':
>> mm/page_alloc.c:5134:3: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast [enabled by default]
In file included from arch/mips/include/asm/page.h:49:0,
from include/linux/mmzone.h:20,
from include/linux/gfp.h:4,
from include/linux/mm.h:8,
from mm/page_alloc.c:18:
arch/mips/include/asm/io.h:119:29: note: expected 'const volatile void *' but argument is of type 'long unsigned int'
mm/page_alloc.c: In function 'free_area_init_nodes':
mm/page_alloc.c:5030:34: warning: array subscript is below array bounds [-Warray-bounds]
Also address some minor code review comments.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes under high memory pressure one process gets a page of another
process, which manifests itself with an invalid instruction exception.
This happens because flush_tlb_page fails to clear TLB entries when
called with vma that does not belong to current mm, because it does not
set RASID appropriately. When page reclaiming mechanism swaps physical
pages out replacing their PTEs with none or swap PTEs, it calls
flush_tlb_page. Later physical page may be reused elsewhere, but the
stale TLB mapping still refers to it, allowing process that owned the
mapping to see the new state of that physical page.
Put ASID of the mm that owns vma to the RASID to fix that issue.
Also replace otherwise meaningless local_save_flags with local_irq_save.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tGki
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20130508' of git://github.com/czankel/xtensa-linux
Pull xtensa updates from Chris Zankel:
"Support for the latest MMU architecture that allows for a larger
accessible memory region, and various bug-fixes"
* tag 'xtensa-next-20130508' of git://github.com/czankel/xtensa-linux:
xtensa: Switch to asm-generic/linkage.h
xtensa: fix redboot load address
xtensa: ISS: fix timer_lock usage in rs_open
xtensa: disable IRQs while IRQ handler is running
xtensa: enable lockdep support
xtensa: fix arch_irqs_disabled_flags implementation
xtensa: add irq flags trace support
xtensa: provide custom CALLER_ADDR* implementations
xtensa: add stacktrace support
xtensa: clean up stpill_registers
xtensa: don't use a7 in simcalls
xtensa: don't attempt to use unconfigured timers
xtensa: provide default platform_pcibios_init implementation
xtensa: remove KCORE_ELF again
xtensa: document MMUv3 setup sequence
xtensa: add MMU v3 support
xtensa: fix ibreakenable register update
xtensa: fix oprofile building as module
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove heading and trailing spaces, trim trailing lines, and wrap lines
that are longer than 80 characters.
Signed-off-by: Chris Zankel <chris@zankel.net>
set_rasid_register accepts new RASID SR value, but ASID_USER_FIRST is
ASID value for the ring 1; RASID value is made by ASID_INSERT macro.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commits d065bd810b ("mm: retry page fault when blocking on disk
transfer") and 37b23e0525 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.
Port these changes to xtensa.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Acked-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanups:
- Include <asm/sections.h>,
- Remove the (different) extern declarations,
- Remove the no longer needed address-of ('&') operators,
- Use %p to format pointer differences.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit a2d063ac21 ("extable, core_kernel_data(): Make sure all archs
define _sdata") missed xtensa. Xtensa does have a start of data marker,
but calls it _fdata, causing
kernel/built-in.o:(.text+0x964): undefined reference to `_sdata'
_stext was already defined, but it was duplicated by _fdata.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fold all the mmu_gather rework patches into one for submission
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not referenced by any Makefile. pte_alloc_one_kernel() and
pte_alloc_one() is implemented in arch/xtensa/include/asm/pgalloc.h.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Chris Zankel <chris@zankel.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
On VIVT ARM, when we have multiple shared mappings of the same file
in the same MM, we need to ensure that we have coherency across all
copies. We do this via make_coherent() by making the pages
uncacheable.
This used to work fine, until we allowed highmem with highpte - we
now have a page table which is mapped as required, and is not available
for modification via update_mmu_cache().
Ralf Beache suggested getting rid of the PTE value passed to
update_mmu_cache():
On MIPS update_mmu_cache() calls __update_tlb() which walks pagetables
to construct a pointer to the pte again. Passing a pte_t * is much
more elegant. Maybe we might even replace the pte argument with the
pte_t?
Ben Herrenschmidt would also like the pte pointer for PowerPC:
Passing the ptep in there is exactly what I want. I want that
-instead- of the PTE value, because I have issue on some ppc cases,
for I$/D$ coherency, where set_pte_at() may decide to mask out the
_PAGE_EXEC.
So, pass in the mapped page table pointer into update_mmu_cache(), and
remove the PTE value, updating all implementations and call sites to
suit.
Includes a fix from Stephen Rothwell:
sparc: fix fallout from update_mmu_cache API change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 9617729941 ("Drop free_pages()")
modified nr_free_pages() to return 'unsigned long' instead of 'unsigned
int'. This made the casts to 'unsigned long' in most callers superfluous,
so remove them.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <zankel@tensilica.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
