1. Rewrite of the non-dma data transfer functions to use only ONE mode
of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX
bit pattern. So the TDBR = 0xFFFF inside the read calls won't work.
2. Clear SPI_RDBR before reading and before duplex transfer.
Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a
lot of duplex transfers, this is the main cause of mmc_spi failure.
3. Poll RXS for transfer completion. Polling SPIF or TXS cannot
guarantee transfer completion. This may interrupt a transfer before it
is finished. Also this may leave garbage data in buffer and affect
next transfer.
[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for GPIO controlled SPI Chip Selects. To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.
struct spi_board_info
.chip_select = 0
struct bfin5xx_spi_chip
.cs_gpio = GPIO_P###
There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer. Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do this because when things crash, we get simple names like "setup" and
"start_queue" which is pretty difficult to trace back to the real thing:
the spi driver
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to comments in linux/spi/spi.h:
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is determined
* by the results of previous messages and where the whole transaction
* ends when the chipselect goes intactive.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug can be observed when two SPI devices are sharing the spi bus: One
device is set as SPI CS 7, another one is using SPI CS 4.
In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG
register. From the debug bellow:
cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7
cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4
When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however,
SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode).
Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7
is asserted, however SPISSEL4 will be asserted too (I can see this using
the scope). This is unreasonable according to HRM.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this change, SPI DMA is not reliably under stress tests.
Obiviously it's a hardware issue which is not addressed by any document.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "while" endless loop will cause the system hang if hardware error, so
we add timeout control to make the system alive.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when
enable_dma is disabled, but doesn't work at all when turning DMA on. We
get just 0xff bytes back when trying to read the device.
Change the code around so that it programs the SPI first and then enables
DMA, it seems to work a lot better ...
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
use the properl BIT_CTL_... defines rather than the internal driv er
CFG_SPI_... defines
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We only need to check SPI error when DMA failes, cause that is the DMA IRQ
handling routine.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because of DMA hardware issue, we were trying to use software workaround.
This patch add some useful debug messages to help us debugging the DMA
code.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin's related DMA callback API doesn't need void * cast, so drop it.
And this driver is for all Blackfin processors not only for BF53x, we
update the DMA request label for more meaningful information.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For DMA TX/RX operation in pump_transfers, DMA contriguration code in TX
and RX paths are almost the same. This patch unify the duplicated DMA
code to make it more readable.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the SPI bus registers a receive overflow error, pass the result back up
to the higher levels.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use len_in_bytes when we care about the number of bytes transferred rather
than the number of spi transactions. (this value will be the same for
8bit transfers, but not any other sizes)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We already moved bfin_addr_dcachable() and friends into the cacheflush
header where it belongs, so don't need to include <asm/cplbinit.h> here.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush or invalidate caches before doing DMA transfer, if needed.
[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use PIO for full-duplex transfers, instead of DMA.
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable SPI
platform drivers, to allow module auto loading.
[dbrownell@users.sourceforge.net: more drivers: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in SPI probe: first initialize peripheral pins, and just after
register spi master device. This fixes problems with SPI drivers built-in
kernel.
Singed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix breakage cause by overzealous line wrapping; there should be only one
format string.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use simpler comment headers, and strip out information that is maintained in
GIT history
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI writes should also not return until the last bit is sent.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Full duplex SPI operation should not read a dummy byte at the first transfer.
Bug and fix by Jean-Christian de Rivaz <jc@eclis.ch>:
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3678
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PBX 2 SPI devices need the nonstandard "cs change per word" mechanism.
This patch is one of three updating this driver to make the last data bits get
sent before advancing the transfer ... in this case, before the chipselect
gets deactivated.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the SPI driver's name when requesting gpio lines. When there are gpio
conflicts, this helps to narrow down the problems; "bfin-spi" is not
informative.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove useless return status check in restore_state function. Issue was
pointed out by Michael.
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move global SPI regs_base and dma_ch to struct driver_data. Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing. Plus other minor
updates.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
