Implement sff_irq_check() method for both old and new chips.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert the driver's two bmdma_stop() methods into sff_irq_clear() methods --
they shouldn't have been bothering with clearing interrupts from the very start;
the driver will now use the standard bmdma_stop() method implementation (where
appropriate).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Start using faster version of the bmdma_stop() method for the PCI0646U and newer
chips that have the duplicate interrupt status bits in the I/O mapped MRDMODE
register. Use the old, slow bmdma_stop() method on the older chips, taking into
account that the interrupt bits are not coupled to DMA and that's enough to read
the register to clear the interrupt (on the older chips). Determine what method
to use at the driver load time.
Fix kernel-doc of the bmdma_stop() methods, while at it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert string of the *if* statements all checking 'pdev->revision' into more
natural *switch* statement. While at it, somewhat clarify the comments there...
Increment the driver version, accounting for the patches that neglected to do
this in the past.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes a number of changes with respect to the error-handling
code:
* Remove cleanup calls for the devm functions in both the error handling
code and the remove function. This cleanup is done automatically.
* The previous change simplifies the cleanup code at the end of the
function such that there is nothing to do on the failure of the call to
devm_ioremap. So it is changed to just return directly.
* There is no need for the ifs in the cleanup code at the end of the
function, because in each case the cleanup needed is statically
known. Drop the ifs, add new err labels, and drop the initializations of
the tested variables to NULL.
* Change the call to request_irq to a call to devm_request_irq, so that it
is cleaned up on exit.
* Cause the return value of devm_request_irq to go into the returned
variable rv rather than the unused variable ret. Drop ret.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some platforms need to make use of the AHCI_HFLAG_DELAY_ENGINE flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
We will need this macro in both ahci.c and ahci_platform.c, so just move it
to the header.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
The following commit was intended to fix problems with specific AHCI
controller(s) that would become bricks if the AHCI specification was not
followed strictly (that is, if ahci_start_engine() was called while the
controller was in the wrong state):
commit 7faa33da9b
ahci: start engine only during soft/hard resets
However, some devices currently have issues with that fix, so we must
implement a flag that delays the ahci_start_engine() call only for specific
controllers.
This commit simply introduces the flag, without enabling it in any driver.
Note that even when AHCI_HFLAG_DELAY_ENGINE is not enabled, this patch does
not constitue a full revert to commit 7faa33da; there is still a change in
behavior to the ahci_port_suspend() failure path.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Adds support for interrupt coalescing feature to reduce interrupt events.
Provides a mechanism of adjusting coalescing count and timeout tick by sysfs
at runtime, so that tradeoff of latency and CPU load can be made depending
on different applications.
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds in Hibernation related callbacks. Also we don't really need to
free DMA channel on suspend.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to the HT6560H datasheet, the recovery timing field is 4-bit wide,
with a value of 0 meaning 16 cycles. Correct obvious thinko in the recovery
field mask.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the IDE-mode SATA DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link resets leave ata affiliations intact, so arrange for libsas to make
an effort to avoid dropping the device due to a slow-to-recover link.
Towards this end carry out reset in the host workqueue so that it can
check for ata devices and kick the reset request to libata. Hard
resets, in contrast, bypass libata since they are meant for associating
an ata device with another initiator in the domain (tears down
affiliations).
Need to add a new transport_sas_phy_reset() since the current
sas_phy_reset() is a utility function to libsas lldds. They are not
prepared for it to loop back into eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pata_at91 driver is broken since faee0cc:
"make smc register base soc independent"
Fix it with newly introduced SMC accessors.
The overall action of removal of at91_sys_read/write will allow
to use the pata_at91 on a single zImage kernel.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-ide@vger.kernel.org
BF54x on-chip ATAPI controller allows maximum 0x1fffe bytes to be transfered
in one ATAPI transfer. So, set the max sg_tablesize to 4.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: Yutaka Ando <r46913@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
ahci: support the STA2X11 I/O Hub
pata_bf54x: fix BMIDE status register emulation
ata: add ata port hibernate callbacks
ata: update ata port's runtime status during system resume
[SCSI] runtime resume parent for child's system-resume
ahci: platform support for suspend/resume
libata-core: kill duplicate statement in ata_do_set_mode()
pata_of_platform: remove direct dependency on OF_IRQ
SATA/PATA: convert drivers/ata/* to use module_platform_driver()
pata_cs5536: forward port changes from cs5536
libata-sff: use ATAPI_{COD|IO}
ata: add ata port runtime PM callbacks
ata: add ata port system PM callbacks
[SCSI] sd: check runtime PM status in sd_shutdown
[SCSI] check runtime PM status in system PM
[SCSI] add flag to skip the runtime PM calls on the host
ata: make ata port as parent device of scsi host
ahci: start engine only during soft/hard resets
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
The AHCI controller found in the STA2X11 chip uses BAR number 0
instead of 5. Also, the chip's fixup code sets a special DMA mask
for all of its PCI functions, and the mask must be preserved here.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The author of this driver clearly wasn't familiar with the BMIDE specification
(also known as SFF-8038i) when he implemented the bmdma_status() method: first,
the interrupt bit of the BMIDE status register corresponds to nothing else but
INTRQ signal (ATAPI_DEV_INT here); second, the error bit is only set if the
controller encounters issue doing the bus master transfers, not on the IDE DMA
burst termination interrupts like here (moreover, setting the error bit doesn't
cause an interrupt). We now need to disable all those unused interrupts...
(The only thing I couldn't figure out is how to flush the FIFO to memory once
the interrupt happens as required by the mentioned spec.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.
This also fixes below warning during system suspend/resume.
WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()
4034 WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add platform hooks for custom suspend() and resume() functions. The
generic suspend/resume code in drivers/ata/ahci_platform.c is adapted
from the PCI version in drivers/ata/ahci.c.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit b3a706014e (libata: Add a
drivers/ide style DMA disable) neglected to remove the line in
ata_do_set_mode() it has obviously made useless/duplicated. Do this
now, and make a line added back then wrapped properly...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CONFIG_OF_IRQ is not available on some platforms and using of_irq_*
breaks the build. Since resources are already populated in the platform
device, get the irq from there instead.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts the drivers in drivers/ata/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Munaut <tnt@246tNt.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Mark Miesfeld <mmiesfeld@amcc.com>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Fix cable detection to also account for the slave device cable bit.
* Disable UDMA when programming MWDMA in cs5536_set_dmamode().
* Don't change UDMA settings in cs5536_set_piomode().
* Add cs5536_program_dtc() helper.
* Cleanup and uninline cs5536_[read,write]() methods.
Cc: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
atapi_pio_bytes() uses bare numbers for the ATAPI interrupt reason bits despite
these are #define'd in <linux/ata.h>.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change ata_host_request_pm to ata_port_request_pm which performs
port suspend/resume.
Add ata port type driver which implements port PM callbacks.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, the device tree of ata port and scsi host looks as below,
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
This patch makes ata port as parent device of scsi host, then it becomes
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is another attempt at fixing the same problem that 270dac35c2
(libata: ahci_start_engine compliant to AHCI spec) tried to solve.
Unfortunately, 270dac35c2 created regressions for a lot more common
controllers and got reverted.
This specific AHCI IP block becomes a brick if the DMA engine is
started while DRQ is set. It is not possible to avoid the condition
completely but the most common occurrence is caused by spurious use of
ahci_start_engine() from ahci_start_port() during init sequence.
DMA engine is started after both soft and hard resets and
ahci_start_port() is always followed by resets, so there is no reason
to start DMA engine from ahci_start_port().
This patch removes ahci_start_engine() invocation from
ahci_start_port(). This change makes failure path of
ahci_port_suspend() leave engine stopped without following resets.
This is resolved by replacing ahci_start_port() call with
ata_port_freeze() which forces resets afterwards, which is the better
behavior anyway.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
fix these errors:
drivers/ata/libata-sff.c:2538:3: error: implicit declaration of function
'ata_pci_bmdma_prepare_host'
drivers/ata/libata-sff.c:2549:40: error: 'ata_bmdma_interrupt'
undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The change in commit 904c04feaf "ahci_platform: Add the board_ids..."
doesn't work for the DT probing case as platform_get_device_id returns
NULL. Pick the default ahci_port_info in this case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Richard Zhu <richard.zhu@linaro.org>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Drivers should not use NO_IRQ; moreover, some architectures don't
have it nowadays. '0' is the 'no irq' case.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reenable sending SRST to devices connected behind a Sil3726 PMP.
This allow staggered spinups and handles drives that spins up slowly.
While the drives spin up, the PMP will not accept SRST.
Most controller reissues the reset until the drive is ready, while
some [Sil3124] returns an error.
In ata_eh_error, wait 10s before reset the ATA port and try again.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use dev_get_platdata() to retrieve the struct ahci_platform_data data
from the platform.
Signed-off-by: JiSheng Zhang <jszhang3@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add the documentation of parameters of ata_change_queue_depth to silence the warning of make xmldocs
Signed-off-by: Marcos paulo de Souza <marcos.mage@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in the ide dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include export.h explicitly now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Rename 'idetm_port' and 'idetm_data' variables to 'master_port'
and 'master_data' respectively to match register naming used in
efar_set_dmamode() and in ata_piix.c.
Fix efar_set_piomode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Besides making things noticably simpler it results in ~2% decrease in
the driver LOC count and also ~2% decrease in the driver binary size
(as measured on x86-32).
Fix piix_set_piomode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set SITRE (separate slave timing register) bit also in master-only
configurations to match other PIIX-alike drivers and make further
changes easier.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Always use ata_sff_data_xfer32() in ata_sff_data_xfer_noirq()
so the latter can be also used for host controllers supporting
32-bit PIO operations.
It is a completely safe thing to do because if 32-bit PIO is
not supported or enabled ata_sff_data_xfer32() will fallback
to a standard method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (aec62xx) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (sl82c105) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (pdc202xx_new) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add controller type field to struct legacy_data and then use it
to merge together all ->set_piomode methods for QDI controllers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
QDI65x0 controllers are fully supported by pata_legacy driver
so remove no longer needed pata_qdi driver.
Leave PATA_QDI config option for compatibility reasons and teach
pata_legacy to preserve the old behavior of pata_qdi driver.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rename 'idetm_port' and 'idetm_data' variables to 'master_port'
and 'master_data' respectively to match register naming used in
it8213_set_dmamode() and in ata_piix.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
IDE's it8213 host driver has been supporting those modes
(per official documentation) since the initial driver's merge
on Feb 7 2007 (commit 9c6712c0 "ide: add it8213 IDE driver").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is similar change as commit 60c3be3 ("ata_piix: parallel scanning
on PATA needs an extra locking") for ata_piix host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Fix via_init_one() to enable clock on 66 MHz devices
(bug introduced in commit 460f531 "pata_via: store UDMA masks
in via_isa_bridges table").
* Factor out common code from via_[re]init_one() to via_fixup().
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
XFER_SW_DMA_0 mode should be excluded from the extended cycle timing
computations.
Acked-by: Alan Cox <alan@linux.intel.com>
Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use standard ata_cable_80wire() method for the cable detection,
as a bonus this allows us to use the default ->prereset method.
Acked-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The suspend()/resume() methods already get the right 'struct device' to get the
driver data from -- there's no need to get to the 'struct platform_device' that
contains that 'struct device' just to call dev_get_drvdata()...
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes PCI access before PCI resources are allocated.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Factor out common code from serverworks_[re]init_one() to
serverworks_fixup().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Merge identical cable routines for Dell and Sun systems into
common oem_cable() one.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cosmetic fix but thanks to it pata_ali's DMI table now matches
alim15x3's one.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Core libata code takes care of it nowadays.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Factor out common code from cmd64x_[re]init_one() to cmd64x_fixup().
Remove stale comment and fix a minor CodingStyle issue while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Factor out code for finding the register programming information
from hpt366_set_mode() to hpt36x_find_mode().
This makes pata_hpt366 driver more similar to pata_{37x,3x2n} ones.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Unify ->prereset methods for ATP850 and ATP86x[R] chipsets.
* Fix ->prereset documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Turn both helpers (which are used only during LLDs initialization
time and thus are not performance sensitive) into wrappers around
the new ata_pci_init_one() function, this cuts 20 LOC and saves
~1.1k of the output code size (x86-64):
text data bss dec hex filename
21392 0 19 21411 53a3 drivers/ata/libata-sff.o.before
20256 0 19 20275 4f33 drivers/ata/libata-sff.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
.. and also a module description while at it.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix documentation for sil680_sel[reg,dev]() and sil680_set_[pio,dma]mode().
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds missing #includes, makes the driver selectable on
non-PPC OF-enabled platforms and fixes property value accesses to
be correct in Little Endian system.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove a lot of ' ' (double spaces) as well as ensuring use of tabs vs.
spaces is appropriate and consistent.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This pushes timing and other values into preinitialized read-only data
sections rather than being inlined into the code. None of these
functions are called more than a handful of times, so reducing code size
makes sense.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This ports the timing values over from the old IDE driver into the new
PATA-based one. The comment was lying when it stated the old driver was
not MWDMA capable.
Boot tested on actual hardware using 'libata.force=mwdma2'.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This mirrors a very old commit (3160d5416f, "sis5513: add
->udma_filter method for chipset_family >= ATA_133") to the old sis5513
IDE driver that prevents certain setups from working.
UDMA6 (ATA/133) is not supported on some chipsets and we need to ensure
this mode is not chosen even if a connected drive supports it. Port this
old patch forward to the new PATA driver to ensure UDMA5 is the highest
mode used if that is what is supported.
Kernel bugzilla #41582.
Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is similar to the existing sis_old_port_base() method. We do this
same calculation and logic in multiple places (with one more to come in
a future patch), so extracting it into a method makes sense.
Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
