This patch will add capability in driver to tell firmware that it can
throttle IOs in case controller's queue depth is downgraded post OFU
(online firmware upgrade). This feature will ensure firmware can be
downgraded from higher queue depth to lower queue depth without needing
system reboot. Added throttling code in IO path of driver, in case OS
tries to send more IOs than post OFU firmware's queue depth.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. For iMR controllers, firmware will report two queue depths:
- Controller-wide queue depth
- LDIO queue depth (240)
Controller-wide queue depth will be greater among the two. Using this
new feature, iMR can provide larger Queue depth(QD) for JBOD and limited
QD for Virtual Disk(VD).
2. megaraid_sas driver will throttle read/write LDIOs based on "LDIO
Queue Depth".
3. Dual queue depth can be enabled/disabled via module parameter. It is
enabled by default if the firmware supports it. Only specific firmware
builds will enable the feature.
4. Added sysfs parameter "ldio_outstanding" which permits querying the
number of outstanding LDIO requests at runtime.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
build_and_issue_cmd should return SCSI_MLQUEUE_HOST_BUSY for a few error
cases instead of returning 1.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will create a reply queue pool for each MSI-X index and will
provide an array of base addresses instead of the single address of
legacy mode. Using this new interface the driver can support higher
queue depths through scattered DMA pools.
If array mode is not supported driver will fall back to the legacy
method of reply pool allocation. This limits controller queue depth to
1K max. To enable a queue depth of more than 1K driver requires firmware
to support array mode and scratch_pad3 will provide the new queue depth
value.
When RDPQ is used, downgrading to an older firmware release should not
be permitted. This may cause firmware fault and is not supported.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware will fill out per-LD data to tell driver whether a particular
LD supports region lock bypass. If yes, then driver will send non-FP
LDIO to region lock bypass FIFO. With this change in driver, firmware
will optimize certain code to improve performance.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will update device Queue depth based on interface type(SAS,
SATA..) for sysPDs. For Virtual disks(VDs), there will be no change in
queue depth (will remain 256). To fetch interface type (SAS or SATA or
FC..) of syspD, driver will send DCMD MR_DCMD_PD_GET_INFO.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds task management for SCSI commands. Added functions are
task abort and target reset.
1. Currently, megaraid_sas driver performs controller reset when any IO
times out. With task management support added, task abort and target
reset will be tried to recover timed out IO. If task management fails,
then controller reset will be performaned. If the task management
request times out, fail the request and escalate to the next
level (controller reset).
2. mr_device_priv_data will be allocated for all generations of
controller, but is_tm_capable flag will never be set for
controllers (prior to Invader series) as firmware support is not
available for task management.
3. Task management capable firmware will set is_tm_capable flag in
firmware API.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do proper error handling for DCMD timeout failure cases
for Fusion adapters:
1. For MFI adapters, in case of DCMD timeout (DCMD which must return
SUCCESS) driver will call kill adapter.
2. What action needs to be taken in case of DCMD timeout is decided by
function dcmd_timeout_ocr_possible(). DCMD timeout causing OCR is
applicable to the following commands:
MR_DCMD_PD_LIST_QUERY
MR_DCMD_LD_GET_LIST
MR_DCMD_LD_LIST_QUERY
MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS
MR_DCMD_SYSTEM_PD_MAP_GET_INFO
MR_DCMD_LD_MAP_GET_INFO
3. If DCMD fails from driver init path there are certain DCMDs which
must return SUCCESS. If those DCMDs fail, driver bails out. For optional
DCMDs like pd_info etc., driver continues without executing certain
functionality.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do synhronization between OCR function and AEN function
using "reset_mutex" lock. reset_mutex will be acquired only in the
first half of the AEN function which issues a DCMD. Second half of the
function which calls SCSI API (scsi_add_device/scsi_remove_device)
should be out of reset_mutex to avoid deadlock between scsi_eh thread
and driver.
During chip reset (inside OCR function), there should not be any PCI
access and AEN function (which is called in delayed context) may be
firing DCMDs (doing PCI writes) when chip reset is happening in parallel
which will cause FW fault. This patch will solve the problem by making
AEN thread and OCR thread mutually exclusive.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hpsa driver uses this function to cleanup inquiry data. Our new pqi
driver will also use this function. This function was copied into both
drivers.
This patch exports sanitize_inquiry_string so the hpsa and the pqi
drivers can use this function directly.
Suggested-by: Hannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs mrochs@linux.vnet.ibm.com
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we fail to queue an srb for an async login we should set the
relogin flag so it will be retried as the reason for the queuing
failure was most likely transient. Failure to do this can lead to
failed paths as login is never retried if the relogin flag is not
set.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set bit 12 of additional firmware options 3 to let firmware
hold status IOCB until ABTS response is received from Target.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hwi_write_buffer() does not check if mapping dma memory succeed. The
patch adds the check and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Acked-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Login/Logout loop was hanging after few hours. /var/log/message showed
that alloc_wrb_handle() function was not able to allocate any new WRB.
Sep 11 11:25:22 Jhelum10 kernel: connection32513:0: Could not send nopout
Sep 11 11:25:22 Jhelum10 kernel: scsi host10: BM_4989 : Alloc of WRB_HANDLE
Failed for the CID : 384
Sep 11 11:25:22 Jhelum10 kernel: connection32513:0: Could not allocate pdu for
mgmt task.
Driver allocates WRB to pass login negotiated parameters information to FW
in beiscsi_offload_connection(). This allocated WRB was not freed so there
was WRB_Leak happening.
Put WRB used for posting the login-negotiated parameters back in pool.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use only port_link_status only to determine link state change. Only bit
0 is used to get the state. Remove code for processing port_fault.
Fixed get_nic_conf structure definition. Removed rsvd[23] field in
be_cmd_get_nic_conf_resp.
Moved definitions of struct field values below the field.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Async link event provides port_speed info. Cache the port_speed info
and use the same to report in ISCSI_HOST_PARAM_PORT_SPEED query.
Removed link status query IOCTL used to do the same.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iscsi_port_speed and iscsi_port_speed_names have new entries for
25Gbps and 40Gbps link speeds.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
OS not responding when running 2 port traffic on 72 CPUs system.
be2iscsi IRQs gets affined to CPU0 when irqbalancer is disabled.
be_iopoll processing completions in BLOCK_IOPOLL_SOFTIRQ hogged CPU0.
1. Use budget to exit the polling loop. beiscsi_process_cq didn't honour
it.
2. Rearming of EQ is done only after iopoll completes.
[mkp: Fixed up blk_iopoll -> irq_poll transition]
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change return value of completed MCC EBUSY to EINVAL.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
System crash in I+T card personality.
Fix to add validation for ULP in initiator mode, physical port number,
and supported queue, icd, cid counts.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log messages for misconfigured transceivers reported by FW.
Register async events that driver handles using MCC_CREATE_EXT ioctl.
Errors messages for faulted/uncertified/unqualified optics are logged.
Added IOCTL to get port_name to be displayed in error message.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Configuring VLAN parameters through IPv6 interface was not supported in
driver.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Null pointer dereference in shutdown path after taking dump.
Shutdown path is not needed as FW comes up clean every time during probe
after issuing FUNCTION reset MBOX command.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of mutex_lock_interruptible can return -EINTR, handle and log the
error.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FW recommended timeout for all mbox command is 30s. Use msleep instead
mdelay to relinquish CPU when polling for mbox completion.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
alloc_mcc_tag needs to be done under mcc_lock.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
beiscsi_mccq_compl sets MCC_TAG_STATE_TIMEOUT before setting up
tag_mem_state. be_mcc_compl_process_isr checks for MCC_TAG_STATE_TIMEOUT
first then accesses tag_mem_state which might be still getting populated
in the process context.
Fix: Set MCC_TAG_STATE_TIMEOUT after tag_mem_state is populated.
Removed MCC_TAG_STATE_COMPLETED. When posted its in running state and
the running state is cleared in be_mcc_compl_process_isr. be_mcc_notify
now takes tag argument to set it to running state. Use bit operations
for tag_state. Use barriers before setting the state.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is second part of actual fix for soft lockup.
All mbox cmds issued using BMBX and MCC are synchronized using mutex
mbox_lock instead of spin_lock. Used mutex_lock_interruptible where ever
possible.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We are taking mbox_lock spinlock which disables pre-emption before we
poll for mbox completion. Waiting there with spinlock held in excess of
20s will cause soft lockup.
Actual fix is to change mbox_lock to mutex. The changes are done in
phases. This is the first part.
1. Changed mgmt_get_all_if_id to use MCC where after posting lock is
released.
2. Changed be_mbox_db_ready_wait to busy wait for 12s max and removed
wait_event_timeout. Added error handling code for IO reads.
OPCODE_COMMON_QUERY_FIRMWARE_CONFIG mbox command takes 8s time when
unreachable boot targets configured.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable bugfixes:
- Fix nfs_size_to_loff_t
- NFSv4: Fix a dentry leak on alias use
Other bugfixes:
- Don't schedule a layoutreturn if the layout segment can be freed immediately.
- Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
- rpcrdma_bc_receive_call() should init rq_private_buf.len
- fix stateid handling for the NFS v4.2 operations
- pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
- fix panic in gss_pipe_downcall() in fips mode
- Fix a race between layoutget and pnfs_destroy_layout
- Fix a race between layoutget and bulk recalls
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/WDS
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.5-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Stable bugfixes:
- Fix nfs_size_to_loff_t
- NFSv4: Fix a dentry leak on alias use
Other bugfixes:
- Don't schedule a layoutreturn if the layout segment can be freed
immediately.
- Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
- rpcrdma_bc_receive_call() should init rq_private_buf.len
- fix stateid handling for the NFS v4.2 operations
- pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
- fix panic in gss_pipe_downcall() in fips mode
- Fix a race between layoutget and pnfs_destroy_layout
- Fix a race between layoutget and bulk recalls"
* tag 'nfs-for-4.5-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.x/pnfs: Fix a race between layoutget and bulk recalls
NFSv4.x/pnfs: Fix a race between layoutget and pnfs_destroy_layout
auth_gss: fix panic in gss_pipe_downcall() in fips mode
pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
nfs4: fix stateid handling for the NFS v4.2 operations
NFSv4: Fix a dentry leak on alias use
xprtrdma: rpcrdma_bc_receive_call() should init rq_private_buf.len
pNFS: Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
pNFS: Fix pnfs_mark_matching_lsegs_return()
nfs: fix nfs_size_to_loff_t
In commit 11f1a4b975 ("x86: reorganize SMAP handling in user space
accesses") I changed how the stac/clac instructions were generated
around the user space accesses, which then made it possible to do
batched accesses efficiently for user string copies etc.
However, in doing so, I completely spaced out, and didn't even think
about the 32-bit case. And nobody really even seemed to notice, because
SMAP doesn't even exist until modern Skylake processors, and you'd have
to be crazy to run 32-bit kernels on a modern CPU.
Which brings us to Andy Lutomirski.
He actually tested the 32-bit kernel on new hardware, and noticed that
it doesn't work. My bad. The trivial fix is to add the required
uaccess begin/end markers around the raw accesses in <asm/uaccess_32.h>.
I feel a bit bad about this patch, just because that header file really
should be cleaned up to avoid all the duplicated code in it, and this
commit just expands on the problem. But this just fixes the bug without
any bigger cleanup surgery.
Reported-and-tested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace another case where the layout 'plh_block_lgets' can trigger
infinite loops in send_layoutget().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If the server reboots while there is a layoutget outstanding, then
the call to pnfs_choose_layoutget_stateid() will fail with an EAGAIN
error, which causes an infinite loop in send_layoutget(). The reason
why we never break out of the loop is that the layout 'plh_block_lgets'
field is never cleared.
Fix is to replace plh_block_lgets with NFS_LAYOUT_INVALID_STID, which
can be reset after a new layoutget.
Fixes: ab7d763e47 ("pNFS: Ensure nfs4_layoutget_prepare returns...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
One is by Yang Shi who added a READ_ONCE_NOCHECK() to the scan of the
stack made by the stack tracer. As the stack tracer scans the entire
kernel stack, KASAN triggers seeing it as a "stack out of bounds" error.
As the scan is looking at the contents of the stack from parent functions.
The NOCHECK() tells KASAN that this is done on purpose, and is not some
kind of stack overflow.
The second fix is to the ftrace selftests, to retrieve the PID of executed
commands from the shell with "$!" and not by parsing "jobs".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWyycyAAoJEKKk/i67LK/8ALoH/RkMZ7Cih7vXb30wB13xSNrB
6o4ApuC4YOS9Un/4ruCXb+cGbW2LJLHkEU2ageoHLOZMvwuAM7iQ6fTUW1KxCRP2
ECvqyqi0ZRyoi/CibxVVH9hHEAJzUTwok67nkLeZBqIN9Fglcfd7toAwgcrH3y59
Pybyv5CV2eaff5IKoLXKZJNRLdrVLeM7v4BvdI0dxEikhWZ0XsA0RoIaNfTPqyQJ
F6sJ/njdoMMJK4N8CCPxlvnvEOzn0DnJnfUNUQEj5J3YU9DbAHAACaBSg5oSh9oK
BcFYKV2GIzPku1cafutRRlErcGyB2yqv7bB8Eo86zXRHbeonaj4XGJmH276ldVg=
=srlj
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more small fixes.
One is by Yang Shi who added a READ_ONCE_NOCHECK() to the scan of the
stack made by the stack tracer. As the stack tracer scans the entire
kernel stack, KASAN triggers seeing it as a "stack out of bounds"
error. As the scan is looking at the contents of the stack from
parent functions. The NOCHECK() tells KASAN that this is done on
purpose, and is not some kind of stack overflow.
The second fix is to the ftrace selftests, to retrieve the PID of
executed commands from the shell with '$!' and not by parsing 'jobs'"
* tag 'trace-fixes-v4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing, kasan: Silence Kasan warning in check_stack of stack_tracer
ftracetest: Fix instance test to use proper shell command for pids
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWyvatAAoJEFxbo/MsZsTRBFcH+wWnv0/N+gKib3cKCI4lwmTg
n8iVgf8dNWwD36M2s/OlzCAglAIt8Xr6ySNvPqTerpm7lT9yXlIVQxGXTbIGuTAA
h8Kt8WiC0BNLHHlLxBuCz62KR47DvMhsr84lFURE8FmpUiulFjXmRcbrZkHIMYRS
l/X+xJWO1vxwrSYho0P9n3ksTWHm488DTPvZz3ICNI2G2sndDfbT3gv3tMDaQhcX
ZaQR93vtIoldqk29Ga59vaVtksbgxHZIbasY9PQ8rqOxHJpDQbPzpjocoLxAzf50
cioQVyKQ7i9vUvZ+B3TTAOhxisA2hDwNhLGQzmjgxe2TXeKdo3yjYwO6m1dDBzY=
=VY/S
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
* tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
xen/pcifront: Report the errors better.
xen/pciback: Save the number of MSI-X entries to be copied later.
xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
xen: fix potential integer overflow in queue_reply
xen/arm: correctly handle DMA mapping of compound pages
xen/scsiback: avoid warnings when adding multiple LUNs to a domain
xen/scsiback: correct frontend counting
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
Remove an un-necessary speed_index lookup for thermal hook in the gpio-fan
driver. The unnecessary speed lookup can hog the system.
Handle negative conversion values correctly in the ads1015 driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=luAI
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two fixes headed for stable:
- Remove an unnecessary speed_index lookup for thermal hook in the
gpio-fan driver. The unnecessary speed lookup can hog the system.
- Handle negative conversion values correctly in the ads1015 driver"
* tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
hwmon: (ads1015) Handle negative conversion values correctly
- One fix ocrdma - The new CQ API support was added to ocrdma, but they
got the arming logic wrong, so without this, transfers eventually fail
when they fail to arm the interrupt properly under load
- Two related fixes for mlx4 - When we added the 64bit extended counters
support to the core IB code, they forgot to update the RoCE side of the
mlx4 driver (the IB side they properly updated). I debated whether or
not to include these patches as they could be considered feature
enablement patches, but the existing code will blindy copy the 32bit
counters, whether any counters were requested at all (a bug). These
two patches make it A) check to see that counters were requested and
B) copy the right counters (the 64bit support is new, the 32bit is
not). For that reason I went ahead and took them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWxI9xAAoJELgmozMOVy/dqRgP/3JbB5MMcqqrxCXGE7874YOO
ZXldH2nJ+uIffWn1IUDJd01vWKDbxBD5joD+HgH1XLjmSQZf7I6APmayTMx43k/k
Ps4fg4iDU2HY35w4s8hCgIj1WmKtYWPA2wHFB1VUO8nhLQD0fxCInw3feDhOXu23
VYSBOypHIMHZfldOog/RXQ4/cCStTmhyDlPtcldWTpMm/SmBEs/iGoUXe5gLHZfk
aKEK2OOC/Yk/iK4flnYsNcgDhFfTcFlpbUtBfLYvFd9UxBCkPsB7WE5BT06zvEHe
Cp5IN7093Nhh66uKyDHyzBJFMrZB3crcqmEGsauE6iBF6iQItlvVMch7DHP4FEWP
2VlYKbhINH7yfl/bXq9CyljA2wcPS5MDtQgrEwa/qMeA8sqEQWnyPgS4xGKnufoQ
SbvPY9pdzhU2G6weoRSiVfpMXh2dl/kbOcsn/rywfyrJ4Ne1lE60Di75WEpwxD+I
4cRktAZp5W2gnv9NJRA/iYMQCVxJ9Sd7aj+dFfWOzJf3uuOlvMALTPuWF4zyeT1U
VKpptmAmq0l3zVtpnmuVNO4BqC+00L+sojrkeGX9ZhLBaJZfUkj10sjPAWGHNU28
liQ3Wnqb7q5Z7ROBs5bbMub7Q4+hWiEINPQtFm4f43bmievI9QgPjoNQXjXea7vI
W9WXEhYS1fjI9z3w4Oqg
=QD36
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"One ocrdma fix:
- The new CQ API support was added to ocrdma, but they got the arming
logic wrong, so without this, transfers eventually fail when they
fail to arm the interrupt properly under load
Two related fixes for mlx4:
- When we added the 64bit extended counters support to the core IB
code, they forgot to update the RoCE side of the mlx4 driver (the
IB side they properly updated).
I debated whether or not to include these patches as they could be
considered feature enablement patches, but the existing code will
blindy copy the 32bit counters, whether any counters were requested
at all (a bug).
These two patches make it (a) check to see that counters were
requested and (b) copy the right counters (the 64bit support is
new, the 32bit is not). For that reason I went ahead and took
them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx4: Add support for the port info class for RoCE ports
IB/mlx4: Add support for extended counters over RoCE ports
RDMA/ocrdma: Fix arm logic to align with new cq API
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C for you:
A fix for a RuntimePM regression with OMAP, a fix to enable TCO for
Lewisburg platforms, and a typo fix while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Adding Intel Lewisburg support for iTCO
i2c: uniphier: fix typos in error messages
i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit
