The timer uses the URB. Free it only after the timer
has been stopped.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The coherency rules mean that you cannot embed
a buffer inside a descriptor. kmalloc() separately.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In order to reduce decoder latency, enable H264 inner racing mode.
Send lat trans buffer information to core when trigger lat to work,
need not to wait until lat decode done.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Vp8 need to use MM21, but vp9 and h264 need to use HyFbc mode
for mt8195. Vp8/vp9/h264 use the same MM21 format for mt8192.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add lat soc compatible and to support lat soc power/clk helper.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
P010 is a YUV format with 10-bits per component with interleaved UV.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement V4L2_CID_JPEG_COMPRESSION_QUALITY
to set jpeg quality
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix the following coccicheck warning:
drivers/media/platform/samsung/s5p-jpeg/jpeg-core.c:1712:24-25:
WARNING opportunity for max()
max() macro is defined in include/linux/minmax.h. It avoids multiple
evaluations of the arguments when non-constant and performs strict
type-checking.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This bit is marked as reserved in the ADV Hardware Reference Manual.
Resetting this bit seems to cause increased video noise. Setting this
bit according to the Hardware Reference Manual reduces the video noise
immediately.
Signed-off-by: Benjamin Marty <info@benjaminmarty.ch>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is a very old driver for very old hardware and it is one of
the very few remaining that does not use the vb2 framework (or
even the older videobuf framework), so deprecate this driver
and move it to staging with the intent to removing it altogether
by the end of 2022.
If someone wants to keep this driver, then it has to be converted
to use vb2.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The variables f_chk_len and f_chk_addr are being initialized to zero and
then being re-assigned in the next statement. The initializations are
redundant and can be removed. Also initialize s_chk_addr and s_chk_len
at the declaration statement.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As there is no interface to power off vpu core.
So it need to boot from cold on first load.
but on the second load, driver need to restore the status
instead of booting.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Eliminate the following coccicheck warning:
./drivers/media/platform/atmel/atmel-isc-base.c:1469:2-3: Unneeded
semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
clk_prepare_enable() already checks NULL by using !clk.
clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL checks before them.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add PAL-Nc support to usbtv, the corresponding register value "0x00fe"
comes from the Windows driver "Active Development Co., Ltd. v2.1.1.2".
Signed-off-by: Jorge Maidana <jorgem.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
* Fix PAL-Nc horizontal parameters according to DScaler:
https://github.com/JohnAdders/DScaler/blob/f7d92b76678e/DScaler/TVFormats.cpp#L88-L94
* Add PAL-Nc TV audio support.
* Tested with CVBS and RF on a Pinnacle PCTV HD 800i.
Signed-off-by: Jorge Maidana <jorgem.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a vivid control to insert the HDMI Video Guard Band in the
image.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This inserts 4 pixels of the RGB color 0xab55ab at the left hand side of
the image. This is only done for 3 or 4 byte RGB pixel formats. The HDMI
TMDS encoding of this pixel value equals the Video Guard Band value as
defined by HDMI (see section 5.2.2.1 in the HDMI 1.3 Specification) that
preceeds the first actual pixel of a video line. If an HDMI receiver
doesn't handle this correctly, then it might keep skipping these Video
Guard Band patterns and end up with a shorter video line. So this is a
nice pattern to test with.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If there is a hardware problem such as someone pulling the CEC line low
continuously, then the POLL message will fail with an error other than
OK, NACK, ABORTED or TIMEOUT. Log the tx_status value in that case to
help debug this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When logging the infoframes the adv7604 driver stopped reading
infoframes at the first missing infoframe type. Instead it should
try all supported infoframe types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To simplify the driver's maintenance it makes sense to escape from
hardcoded numbers of power domain resources per platform and statical
allocation of the resources. For instance on a QCOM SM8450 platform
the number of CAMSS power domains shall be bumped up to 6, also notably
CAMSS on MSM8916 has only one power domain, however it expects to get 2,
and thus it should result in a runtime error on driver probe.
The change fixes an issue mentioned above and gives more flexibility
to support more platforms in future.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
of_graph_get_next_endpoint() returns an 'endpoint' node pointer
with refcount incremented. The refcount should be decremented
before returning from vpif_probe().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver should disable the regulator when failing to probe.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'supplies' is a pointer, the real size of struct regulator_bulk_data
should be pass to devm_kmalloc_array().
Fixes: 0d81401797 ("media: camss: Add regulator_bulk support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The core will fill this in v4l_fill_fmtdesc(),
ensuring consistent format description names.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding
to very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space
to remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections
that have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting.
This makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core
from Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmKNMPQACgkQMUZtbf5S
IrsRARAAuDyYs6jFYB3p+xazZdOnbF4iAgVv71+DQGvmsCl6CB9OrsNZMlvE85OL
Q3gjcRbgjrkN4lhgI8DmiGYbsUJnAvVjFdNjccz1Z/vTLYvuIM0ol54MUp5S+9WY
StncOJkOGJxxR/Gi5gzVmejPDsysU3Jik+hm/fpIcz8pybXxAsFKU5waY5qfl+/T
TZepfV0VCfqRDjqcF1qA5+jJZNU8pdodQlZ1+mh8bwu6Jk1ZkWkj6Ov8MWdwQldr
LnPeK/9hIGzkdJYHZfajxA3t8D0K5CHzSuih2bJ9ry8ZXgVBkXEThew778/R5izW
uB0YZs9COFlrIP7XHjtRTy/2xHOdYIPlj2nWhVdfuQDX8Crvt4VRN6EZ1rjko1ZJ
WanfG6WHF8NH5pXBRQbh3kIMKBnYn6OIzuCfCQSqd+niHcxFIM4vRiggeXI5C5TW
vJgEWfK6X+NfDiFVa3xyCrEmp5ieA/pNecpwd8rVkql+MtFAAw4vfsotLKOJEAru
J/XL6UE+YuLqIJV9ACZ9x1AFXXAo661jOxBunOo4VXhXVzWS9lYYz5r5ryIkgT/8
/Fr0zjANJWgfIuNdIBtYfQ4qG+LozGq038VA06RhFUAZ5tF9DzhqJs2Q2AFuWWBC
ewCePJVqo1j2Ceq2mGonXRt47OEnlePoOxTk9W+cKZb7ZWE+zEo=
=Wjii
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding to
very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space to
remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections that
have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting. This
makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core from
Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection"
* tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1809 commits)
ptp: ocp: Add firmware header checks
ptp: ocp: fix PPS source selector debugfs reporting
ptp: ocp: add .init function for sma_op vector
ptp: ocp: vectorize the sma accessor functions
ptp: ocp: constify selectors
ptp: ocp: parameterize input/output sma selectors
ptp: ocp: revise firmware display
ptp: ocp: add Celestica timecard PCI ids
ptp: ocp: Remove #ifdefs around PCI IDs
ptp: ocp: 32-bit fixups for pci start address
Revert "net/smc: fix listen processing for SMC-Rv2"
ath6kl: Use cc-disable-warning to disable -Wdangling-pointer
selftests/bpf: Dynptr tests
bpf: Add dynptr data slices
bpf: Add bpf_dynptr_read and bpf_dynptr_write
bpf: Dynptr support for ring buffers
bpf: Add bpf_dynptr_from_mem for local dynptrs
bpf: Add verifier support for dynptrs
bpf: Suppress 'passing zero to PTR_ERR' warning
bpf: Introduce bpf_arch_text_invalidate for bpf_prog_pack
...
As per spec, the field reflist requires interleaving top and bottom
field in a specific way that does not fit inside the sort operation.
The process consist of alternating references parity, starting with
a reference of the same parity as the current picture. This
processs is done twice, once for short term references and a second
time for the long term references.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the reference list builder, frame_num refers to FrameNumWrap
in the spec, which is the same as the pic_num for frame decoding.
The same applies for long_term_pic_num and long_term_frame_idx.
Sort all type of references by frame_num so the sort can be reused
for fields reflist were the sorting is done using frame_num instead.
In short, pic_num is never actually used for building reference
lists.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add debug print statements to print the content of P & B reference
lists, to verify that the ordering of the generated reference lists is
correct. This is especially important for the field decoding mode,
where sorting is more complex.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the current picture is a field, store each field into the
unordered_list and preserve both top and bottom picture order
count.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This information, also called picture structure, is required in field
decoding mode to construct reference lists.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is to accommodate support for field decoding, which splits the top
and the bottom references into the reference list.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In preparation for adding field decoding support, convert the byte arrays
for reflist into array of struct v4l2_h264_reference. That struct will
allow us to mark which field of the reference picture is being referenced.
[hverkuil: top_field_order_cnt -> pic_order_count]
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As reported by smatch/sparse:
drivers/media/i2c/ov7251.c:1381 ov7251_s_stream() warn: inconsistent returns '&ov7251->lock'.
Locked on : 1381
Unlocked on: 1377
There's a lock unbalance at this routine, as it keeps the lock on
certain errors. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a vblank control to the ov7251 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a hblank control to the ov7251 driver. This necessitates setting
a default mode, for which I am simply picking the first available.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2 controls initialisation takes up a sizeable portion of the
driver's .probe() function. To keep things neat, move it to a
dedicated function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Extend the .get_selection() callback to support other values for
sel->target, primarily to satisfy libcamera's requirements.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OVTI7251 sensor can be found on x86 laptops with an IPU3, and so
needs to be supported by the cio2-bridge. Add it to the table of
supported sensors.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The .s_power() callback is deprecated, and now that we have pm_runtime
functionality in the driver there's no further use for it. Delete the
function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add pm_runtime support to the ov7251 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe() is quite busy for this driver; make it cleaner by moving the
chip verification to a dedicated function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV7251 sensor is used as the IR camera sensor on the Microsoft
Surface line of tablets; this provides a 19.2MHz external clock, and
the Windows driver for this sensor configures a 319.2MHz link freq to
the CSI-2 receiver. Add the ability to support those rate to the
driver by defining a new set of PLL configs.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rather than having the pll settings hidden inside mode blobs, define
them in structs and use a dedicated function to set them. This makes
it simpler to extend the driver to support other frequencies for both
the external clock and desired link frequency.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Each of the defined modes in the ov7251 driver uses the same link
frequency and pixel rate; just drop those members of the modes and
set the controls to read only during initialisation. Add a new
table defining the supported pixel rates to substitue for the values
hardcoded in the modes.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
