The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used. If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.
It works by reintroducing and expanding the skb_alloc_page() API to take
an skb. If the page was allocated from pfmemalloc reserves, it is
automatically copied. If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.
Failure to do so is not critical. The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.
[davem@davemloft.net: API rename and consistency]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem is that we call this with a spin lock held. The call tree
is:
kaweth_start_xmit() holds kaweth->device_lock.
-> kaweth_async_set_rx_mode()
-> kaweth_control()
-> kaweth_internal_control_msg()
The kaweth_internal_control_msg() function is only called from
kaweth_control() which used GFP_ATOMIC for its allocations.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates and fixes from David Miller:
1) Reinstate the no-ref optimization for input route lookups in ipv4 to
fix some routing cache removal perf regressions.
2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet.
3) Get RX hash value from correct place in be2net driver, from
Sarveshwar Bandi.
4) Validation of FIB cached routes missing critical check, from Eric
Dumazet.
5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
ipv6: Early TCP socket demux
ipv4: Fix input route performance regression.
pch_gbe: vlan skb len fix
pch_gbe: add extra clean tx
pch_gbe: fix transmit watchdog timeout
ixgbe: fix panic while dumping packets on Tx hang with IOMMU
be2net: Fix to parse RSS hash from Receive completions correctly.
net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER
hyperv: Add error handling to rndis_filter_device_add()
hyperv: Add a check for ring_size value
ipv4: rt_cache_valid must check expired routes
net/pch_gpe: Cannot disable ethernet autonegation
qeth: repair crash in qeth_l3_vlan_rx_kill_vid()
netiucv: cleanup attribute usage
net: wiznet add missing HAS_IOMEM dependency
be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC
mlx4: Add support for EEH error recovery
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
wanmain: comparing array with NULL
caif: fix NULL pointer check
...
Tag Ericsson NCM devices as WWAN modems, since they almost certainly all
are. This way userspace clients know that the device requires further
setup on the AT-capable serial ports before connectivity is available.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Since commit 16626b0cc3 the asix
driver depends on the phylib. Select phylib when the asix driver is
selected.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the asix_set_eeprom() function to provide support for
programming the configuration EEPROM via ethtool.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for reading the EEPROM via ethtool in the asix
driver has a few issues. It cannot handle odd length values
(accesses must be aligned at 16 bit boundaries) and interprets the
offset provided by ethtool as 16 bit word offset instead as byte offset.
The new code for asix_get_eeprom() introduced by this patch is
modeled after the code in
drivers/net/ethernet/atheros/atl1e/atl1e_ethtool.c
and provides read access to the entire EEPROM with arbitrary
offsets and lengths.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected. usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.
There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table. Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asix AX88172A is a USB 2.0 Ethernet interface that supports both an
internal PHY as well as an external PHY (connected via MII).
This patch adds a driver for the AX88172A and provides support for
both modes and the phylib.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the new driver for the AX88172A to share code with the
existing drivers for ASIX devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch further creates two additional copies of asix.c.
In another patch these copies will be used to factor out
common code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by implementation in smsc911x.c and smsc9420.c
Tested on ARM/pandaboard running android
Signed-off-by: Emeric Vigier <emeric.vigier@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a device with limited QMI support. It does not support
normal QMI_WDS commands for connection management. Instead,
sending a QMI_CTL SET_INSTANCE_ID command is required to
enable the network interface:
01 0f 00 00 00 00 00 00 20 00 04 00 01 01 00 00
A number of QMI_DMS and QMI_NAS commands are also supported
for optional device management.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed excess calls to skb_copy_expand() or memmove() in asix driver.
This driver needs to push 4 bytes in front of frame (packet_len)
and maybe add 4 bytes after the end (if padlen is 4)
So it should set needed_headroom & needed_tailroom to avoid
copies. But its not enough, because many packets are cloned
before entering asix_tx_fixup() and this driver use skb_cloned()
as a lazy way to check if it can push and put additional bytes in frame.
Avoid skb_copy_expand() expensive call, using following rules :
- We are allowed to push 4 bytes in headroom if skb_header_cloned()
is false (and if we have 4 bytes of headroom)
- We are allowed to put 4 bytes at tail if skb_cloned()
is false (and if we have 4 bytes of tailroom)
TCP packets for example are cloned, but skb_header_release()
was called in tcp stack, allowing us to use headroom for our needs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Allan Chou <allan@asix.com.tw>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is easier to read if we specify which flags we want at the
condition instead of at the top of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the iPad to the ipheth driver.
(product id = 0x129a)
Signed-off-by: Davide Gerhard <rainbow@irh.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
If usbnet is resumed by remote wakeup, generally there are
some packets comming to be handled, so allocate and submit
rx URBs in usbnet_resume to avoid delays introduced by tasklet.
Otherwise, usbnet may have been runtime suspended before the
usbnet_bh is executed to schedule Rx URBs.
Without the patch, usbnet can't recieve any packets from peer
in runtime suspend state if runtime PM is enabled and
autosuspend_delay is set as zero.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decreases dev->suspend_count in the -EBUSY failure path
of usbnet_suspend. Without the change, the later runtime suspend
will do nothing except for increasing dev->suspend_count.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignoring interfaces with additional descriptors is not a reliable
method for locating the correct interface on Gobi devices. There
is at least one device where this method fails:
https://bbs.archlinux.org/viewtopic.php?id=143506
The result is that the AT command port (interface #2) is hidden
from qcserial, preventing traditional serial modem usage:
[ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device
[ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22
[ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device
[ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22
[ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected
[ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0
[ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected
[ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1
Use static interface numbers taken from the interface map in
qcserial for all Gobi devices instead:
Gobi 1K USB layout:
0: serial port (doesn't respond)
1: serial port (doesn't respond)
2: AT-capable modem port
3: QMI/net
Gobi 2K+ USB layout:
0: QMI/net
1: DM/DIAG (use libqcdm from ModemManager for communication)
2: AT-capable modem port
3: NMEA
This should be more reliable over all, and will also prevent the
noisy "probe failed" messages. The whitelisting logic is expected
to be replaced by direct interface number matching in 3.6.
Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de>
Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic
Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The description is used in ethtool fixed length fields. Make
it shorter to avoid truncation.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always bind to control interface regardless of whether
it is a shared interface or not.
A QMI/wwan function is required to provide both a control
interface (QMI) and a data interface (wwan). All devices
supported by this driver do so. But the vendors may
choose to use different USB descriptor layouts, and some
vendors even allow the same device to present different
layouts.
Most of these devices use a USB descriptor layout with a
single USB interface for both control and data. But some
split control and data into two interfaces, bound together
by a CDC Union descriptor on the control interface. Before
the cdc-wdm subdriver support was added, this split was
used to let cdc-wdm drive the QMI control interface and
qmi_wwan drive the wwna data interface.
This split driver model has a number of issues:
- qmi_wwan must match on the data interface descriptor,
which often are indistiguishable from data interfaces
belonging to other CDC (like) functions like ACM
- supporting a single QMI/wwan function requires adding
the device to two drivers
- syncronizing the probes among a number of drivers, to
ensure selecting the correct driver, is difficult unless
all drivers match on the same interface
This patch resolves these problems by using the same
probing mechanism as cdc-ether for devices with a two-
interface USB descriptor layout. This makes the driver
behave consistently, supporting both the control and data
part of the QMI/wwan function, regardless of the USB
descriptors.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the subdriver registration code can be reused for devices
with separate control and data interfaces. Move the code a bit
around to prepare for such reuse.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet allocates a fixed size array for minidriver specific
state. Naming the fields and taking advantage of type checking
is a bit more failsafe than casting array elements each time
they are referenced.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
As seen on smsc75xx, driver_info->description being longer than 32
characters messes up 'ethtool -i' output.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The line below in intr_complete isn't needed,
memset(urb->transfer_buffer, 0, urb->transfer_buffer_length);
so just remove it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove declaration for intr_complete so that ctags may be happy to
decrease duplicated symbols, also decrease one line code.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding device IDs for Aircard 320U and two other devices
found in the out-of-tree version of this driver.
Cc: linux@sierrawireless.com
Cc: Autif Khan <autif.mlist@gmail.com>
Cc: Tom Cassidy <tomas.cassidy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
asix driver drops 8021Q full size frames because it doesn't take into
account VLAN header size.
Tested on AX88772 adapter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Allan Chou <allan@asix.com.tw>
CC: Trond Wuellner <trond@chromium.org>
CC: Grant Grundler <grundler@chromium.org>
CC: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some additional Gobi3K IDs found in the BSD/GPL licensed
out-of-tree GobiNet driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as well.
We deleted a staging driver, which was nice, and finally dropped the
obsolete usbfs code, which will make Al happy to never have to touch
that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were due
to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
=4jM1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
Add the ZTE (Vodafone) K3765-Z to the whitelist. This requires the
previous patch to make the whitelist with forced interface 4 generic
or the device fails to initialise. After applying this patch and
loading the Option driver without usb-modeswitch's bind all
interfaces trick, a wwan0 net interface and /dev/cdc-wdm0 device
file were created. Using Bjorn Mork's perl connection script a
connection was made to a mobile network using QMI and the network
interface's IPv4 address was configured OK.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the forced interface 4 whitelist to use the generic shared
binder instead of the Gobi specific one. Certain ZTE devices
(K3520-Z & K3765-Z) don't work with the Gobi version, but function
quite happily with the generic. This has been tested with the following
devices:
K3520-Z
K3565-Z
K3765-Z
K4505-Z
It hasn't been tested with the ZTE MF820D, which is the only other
device that uses this whitelist at present. Although Bjorn doesn't
expect any problems, any testing with that device would be appreciated.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
