This patch adds support for analog part of Medion 95700 in the cxusb
driver.
What works:
* Video capture at various sizes with sequential fields,
* Input switching (TV Tuner, Composite, S-Video),
* TV and radio tuning,
* Video standard switching and auto detection,
* Radio mode switching (stereo / mono),
* Unplugging while capturing,
* DVB / analog coexistence.
What does not work yet:
* Audio,
* VBI,
* Picture controls.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: remove left-over commented-out debug message]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch prepares cxusb driver for supporting the analog part of
Medion 95700 (previously only the digital - DVB - mode was supported).
Specifically, it adds support for:
* switching the device between analog and digital modes of operation,
* enforcing that only one mode is active at the same time due to hardware
limitations.
Actual implementation of the analog mode will be provided by the next
commit.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to V4L2 API set_fmt subdev operation should not return an error
on out-of-range picture sizes, the values should be clamped instead to the
supported range.
The cx25840 datasheet says that the chip is capable of scaling down the
picture width and height, respectively, 16 and 8 times.
These values agree with what the old implementation enforced.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This commit adds pin to pad mapping and output format configuration support
in CX2584x-series chips to cx25840 driver.
This functionality is then used to allow disabling ivtv-specific hacks and
configuration values (called a "generic mode"), so cx25840 driver can be
used for other devices not needing them without risking compatibility
problems.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This commit implements g_std operation in cx25840 driver by returning the
last set video standard.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx25840 driver g_std operation queries the currently detected video signal,
however this is what querystd operation should do, so let's rename the
handler.
None of the existing cx25840 driver users ever called the g_std operation,
one of them calls querystd on each of its subdevs but then the result is
only used to implement VIDIOC_QUERYSTD (as it should).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx25840_load_fw() does the same thing as cx25840_reset(), only keeps
"is_initialized" flag so any further invocation of this function besides
the first one is a NOP.
Let's just call cx25840_reset() directly from cx25840_load_fw() instead of
open coding it there.
While we are at it, let's also improve comments about cx25840_load_fw()
so they are current and in the proper style (one of them even referred to a
non-existing cx25840 init operation).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The other subdevice implementations in vimc (debayer and scaler) which
share their code structure with the sensor do not have an explicit
return statement at the end of the s_stream(0) code path. Align the
sensor subdevice by dropping the return statement.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the system has other devices being registered in the component
framework, the compare function will be called with a device that
doesn't belong to vimc.
This device is not necessarily a platform_device, nor have a
platform_data (which causes a NULL pointer dereference error) and if it
does have a pdata, it is not necessarily type of struct vimc_platform_data.
So casting to any of these types is wrong.
Instead of expecting a given pdev with a given pdata, just expect for
the device it self. vimc-core is the one who creates them, we know in
advance exactly which object to expect in the match.
Fixes: 4a29b70907 ("[media] vimc: Subdevices as modules")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixing use-after-free within __v4l2_ctrl_handler_setup().
Memory is being freed with kfree(new_ref) for duplicate
control reference entry but ctrl->cluster pointer is still
referring to freed duplicate entry resulting in error on
access. Change done to update cluster pointer only when new
control reference is added.
==================================================================
BUG: KASAN: use-after-free in __v4l2_ctrl_handler_setup+0x388/0x428
Read of size 8 at addr ffffffc324e78618 by task systemd-udevd/312
Allocated by task 312:
Freed by task 312:
The buggy address belongs to the object at ffffffc324e78600
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 24 bytes inside of
64-byte region [ffffffc324e78600, ffffffc324e78640)
The buggy address belongs to the page:
page:ffffffbf0c939e00 count:1 mapcount:0 mapping:
(null) index:0xffffffc324e78f80
flags: 0x4000000000000100(slab)
raw: 4000000000000100 0000000000000000 ffffffc324e78f80 000000018020001a
raw: 0000000000000000 0000000100000001 ffffffc37040fb80 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc324e78500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffffffc324e78580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffffffc324e78600: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ffffffc324e78680: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
ffffffc324e78700: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vim2m_device_release() will be called by video_unregister_device() to release
various objects.
There are two double-free issue,
1. dev->m2m_dev will be freed twice in error_m2m path/vim2m_device_release
2. the error_v4l2 and error_free path in vim2m_probe() will release
same objects, since vim2m_device_release has done.
Fixes: ea6c7e34f3 ("media: vim2m: replace devm_kzalloc by kzalloc")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This converts the driver to using the BIT macro to increase readability
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kasan reported a use after free in cpia2_usb_disconnect()
It first freed everything and then woke up those waiting.
The reverse order is correct.
Fixes: 6c493f8b28 ("[media] cpia2: major overhaul to get it in a working state again")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+0c90fc937c84f97d0aa6@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Unbinding the driver while streaming caused the driver to hang.
The cause of this was failing to use the v4l2_device release
function and the use of devm_kmalloc for the state structure.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure the default value at least passes the std_validate() tests.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This commit clears the interrupt reason (INT_REASON) register
on the interrupt handler. Without this clearing, the CODA hardware
has been observed to get completely stalled on CODA980 variants,
requiring a pretty deep hardware reset.
The datasheet specifies that the INT_REASON register is set
by the CODA hardware, and should be cleared by the host.
While the CODA versions that are currently supported by this driver
don't seem to need this change, it's a really small change,
so it seems a wise thing to do to avoid hitting some
rare race-condition in the hardware.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current interrupt handler is doing very little, and not doing
any non-atomic operations. Pretty much all it does is accessing
a couple registers, taking a couple spinlocks and then signalling
a completion.
There is no reason this should be a threaded interrupt handler,
so move the handler to regular hard interrupt context.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mutex unlock in the threaded interrupt handler is not paired
with any mutex lock. Remove it.
This bug has been here for a really long time, so it applies
to any stable repo.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is just a cosmetic change to print a more descriptive
message, to distinguish decoder from encoder:
So, instead of printing
coda 2040000.vpu: codec registered as /dev/video[4-5]
With this change, the driver now prints
coda 2040000.vpu: encoder registered as /dev/video4
coda 2040000.vpu: decoder registered as /dev/video5
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the pvrusb2 driver detects that there's something wrong with the
device, it prints a warning message. Right now those message are
printed in two different formats:
1. ***WARNING*** message here
2. WARNING: message here
There's an issue with the second format. Syzkaller recognizes it as a
message produced by a WARN_ON(), which is used to indicate a bug in the
kernel. However pvrusb2 prints those warnings to indicate an issue with
the device, not the bug in the kernel.
This patch changes the pvrusb2 driver to consistently use the first
warning message format. This will unblock syzkaller testing of this
driver.
Reported-by: syzbot+af8f8d2ac0d39b0ed3a0@syzkaller.appspotmail.com
Reported-by: syzbot+170a86bf206dd2c6217e@syzkaller.appspotmail.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is really weird that the media controller sources are all top-level
in drivers/media. It is a bit of a left-over from long ago when most
media sources were all at the top-level. At some point we reorganized
the directory structure, but the media-*.c sources where never moved
to their own directory.
So create a new mc directory and move all sources there. Also rename
the prefix from media- to mc-.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These two slice modes used by the V4L2_CID_MPEG_VIDEO_MULTI_SLICE_MODE
control had a silly typo:
V4L2_MPEG_VIDEO_MULTI_SICE_MODE_MAX_MB
V4L2_MPEG_VIDEO_MULTI_SICE_MODE_MAX_BYTES
SICE should be SLICE.
Rename these enum values, keeping the old ones (under #ifndef __KERNEL__)
for backwards compatibility reasons.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzrJgUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1XAIAJajJpeKc9MVQipi
zWiI+WgHDg8gG/HnLKzP2Zp4MUjTCz30t0rnBbdo6AyK6LnPBL53yxg9q64XN7vI
p/h2ys+/DvqhIYSPWX6C++HYQT4Cb5ghxJABEIsztd3G4nfB9L2vgq9zKSNFusTD
UtfUxufciZPX515TuE4IqWMwS4Ut5daH7V3jjZunhPiayTFv64e1KbpKLLzHR0NR
DfFbrPcdp7VyCT/A5AKrqfqeB6O9dm/Fe4CsdsaKuzASCXJ6GUc/A7iZDndv/KA4
f5Xh7SGlQ2TfT1ud/aMfdw3AcMjqB8zgMJenovJ7UuHDfULBWNeAmMh/cTDwY9eY
Xgyvfm0=
=S8p9
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc2' into patchwork
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
Most Siano devices require an alignment for the response.
Changeset f3be52b0056a ("media: usb: siano: Fix general protection fault in smsusb")
changed the logic with gets such aligment, but it now produces a
sparce warning:
drivers/media/usb/siano/smsusb.c: In function 'smsusb_init_device':
drivers/media/usb/siano/smsusb.c:447:37: warning: 'in_maxp' may be used uninitialized in this function [-Wmaybe-uninitialized]
447 | dev->response_alignment = in_maxp - sizeof(struct sms_msg_hdr);
| ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
The sparse message itself is bogus, but a broken (or fake) USB
eeprom could produce a negative value for response_alignment.
So, change the code in order to check if the result is not
negative.
Fixes: 31e0456de5 ("media: usb: siano: Fix general protection fault in smsusb")
CC: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.414247666@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 44 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.032047323@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details to
obtain the license point your browser to http www gnu org copyleft
gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 26 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091650.572604764@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version author [bill] [dirks]
[bill]@[thedirks] [org] [based] [on] [code] [by] [alan] [cox]
[alan]@[cymru] [net] video capture interface for linux a generic
video device interface for the linux operating system using a set of
device structures vectors for low level operations this program is
free software you can redistribute it and or modify it under the
terms of the gnu general public license as published by the free
software foundation either version 2 of the license or at your
option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520075211.410073327@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license vs published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mvss ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071859.384981802@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071859.105288849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version of 2 of the license or
at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.207758043@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa or point your
browser to http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.367248213@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/qcom/venus/firmware.c:90:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
drivers/media/platform/qcom/venus/firmware.c:94:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
drivers/media/platform/qcom/venus/firmware.c:128:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drop the reference to "parallel-ports" and remote endpoint's parent
nodes obtained previously with of_get_child_by_name() and
of_get_parent() respectively.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While correct, the code is too complex for smatch to undersdand
that protocol will always be initialized:
drivers/media/rc/rc-main.c:1531 store_wakeup_protocols() error: uninitialized symbol 'protocol'.
drivers/media/rc/rc-main.c:1541 store_wakeup_protocols() error: uninitialized symbol 'protocol'.
So, change it a little bit in order to avoid such warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In v4l2-compliance utility, test MEDIA_IOC_ENUM_ENTITIES
will check whether reserved field of media_links_enum filled
with zero.
However, for 32 bit program, the reserved field is missing
copy from kernel space to user space in media_device_enum_links32
function.
This patch adds the cleaning a reserved field logic in
media_device_enum_links32 function.
Signed-off-by: Jungo Lin <jungo.lin@mediatek.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clean up of resources should be in reverse order of vpss_init().
Fix this inside vpss_exit().
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove the header search path to the current directory.
The compiler will search headers in the current directory by
using #include "..." instead of #include <...>
Also, change TRACE_INCLUDE_PATH to point to the location of trace.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Embedded systems often connect to sensors or other multimedia
subdevices directly. Currently, to be able to select such a
subdevice (e.g. CONFIG_VIDEO_OV5640) disabling of the auto-
select config option is needed (CONFIG_MEDIA_SUBDRV_AUTOSELECT).
This is inconvenient as the ancillary drivers for a particular
device then need to be selected manually.
Allow to select drivers manually while keeping the auto-select
feature in case EXPERT (selected by EMBEDDED) is enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The size argument of the alloc memop, which allocates buffer memory, is
page aligned. Document it as such in the only caller as well as ops
documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
buf->size is an unsigned long; casting that to int will lead to an
overflow if buf->size exceeds INT_MAX.
Fix this by changing the type to unsigned long instead. This is possible
as the buf->size is always aligned to PAGE_SIZE, and therefore the size
will never have values lesser than 0.
Note on backporting to stable: the file used to be under
drivers/media/v4l2-core, it was moved to the current location after 4.14.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
PAGE_ALIGN() may wrap the buffer size around to 0. Prevent this by
checking that the aligned value is not smaller than the unaligned one.
Note on backporting to stable: the file used to be under
drivers/media/v4l2-core, it was moved to the current location after 4.14.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need for a high-accuracy delay here as long as it is more than 2
milliseconds this should be ok - as it is non-atomic context it will
be not be precise 2 milliseconds so giving the hrtimer subsystem 50
microseconds to merge timers and reduce interrupts.
Signed-off-by: Nicholas Mc Guire <hofrat@opentech.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit
05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
that claimed to add CSI2 turned on C0_EOF_VSYNC for parallel bus
without a very good explanation.
That broke camera on OLPC XO-1.75 which precisely uses a sensor on a
parallel bus. Revert that chunk.
Tested on an OLPC XO-1.75.
Fixes: 05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Fixes: d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
C-PHY doesn't use a clock lane, hence the test for the clock lane when
there isn't one is faulty. Rework the test for the conflicting clock lane.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the v4l2 controls are set up for autofoo/foo-type handling by calling
v4l2_ctrl_auto_cluster() with the last set_volatile argument setting true,
each non-auto control doesn't need to be flagged V4L2_CTRL_FLAG_VOLATILE.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Setting the value of the V4L2_CID_VFLIP control is currently ignored.
Because V4L2_CID_HFLIP and V4L2_CID_VFLIP are independently controlled
in s_ctrl() but these controls belong to the same cluster and the first
control is V4L2_CID_HFLIP.
Fix it by not clustering these controls. Also correct erroneous updating
register bit for vertical flip.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the requested framesize by VIDIOC_SUBDEV_S_FMT is larger than supported
framesizes, it causes an out of bounds array access and the resulting
framesize is unexpected.
Avoid out of bounds array access and select the default framesize.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid returning without decrement the usage count in s_ctrl().
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some displays pull down the HPD when in standby, but CEC is still
active and the display can be woken up by sending an Image View On
or Text View On CEC command. The CEC specification doesn't tell you
what the initiator should be for such a command (without a HPD it's
unclear if the CEC adapter can claim a logical address).
This patch allows any initiator value when there is no HPD for the
Image/Text View On commands and for the Ping command.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If this flag is set, then check for root permissions and skip
all message checks expect for the core checks (i.e. validate the
length etc.).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds the userspace API to send raw unchecked CEC messages.
This will require root permissions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This ensures all the cec_msg checks are done in the same place.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code that fills in the CEC_MSG_CDC_MESSAGE physical address
is now done after the sanity checks. It also only does this if the
message length is >= 4 (i.e. there is room for the physical address).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Due to limitations in gpiolib it was impossible to disable the interrupt of
an input gpio and then switch it to gpio output and drive it. The only way
to achieve that was to free the interrupt first, then switch the direction.
When going back to gpio input and using interrupts to read the gpio pin you
had to request the irq again.
This limitation was lifted in gpiolib in kernel 4.20, but the cec-gpio driver
was still using the old workaround implementation.
This patch updates the cec-gpio driver to just enable and disable the irq.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec device node can be used right after it was created, but that
leaves a race condition where the device was created, but devnode->registered
was still false. So an ioctl() would result in an error.
So set it to true before calling cdev_device_add() and to false again if
cdev_device_add returned an error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This can be a debug message. Favour dev_dbg() over dprintk() as this is
already used much more than dprintk().
dvb_frontend: dvb_frontend_get_frequency_limits: frequency interval: tuner: 45000000...860000000, frontend: 44250000...867250000
Fixes: 00ecd6bc71 ("media: dvb_frontend: add debug message for frequency intervals")
Cc: <stable@vger.kernel.org> # 5.0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove comment and replace with the appropriate SPDX identifier.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All error cases inside the function already report errors via dev_err(),
and dvb_usb_v2_generic_rw also reports all error cases, so there is
no silent code path when an error has occurred.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Errors are already reported by the common code in dvb_usb_v2_generic_io
(which dvbsky_usb_generic_rw is a wrapper of), so there is no reason
report the error again.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
actual_length != wlen is the only error path which does not generate an
error message. Adding an error message here allows to report a more
specific error and to remove the error reporting from the call sites.
Also clean up the error paths - in case of an error, the remaining
code is skipped, and ret is returned. Skip setting ret and return
immediately (no cleanup necessary).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
au0828_usb_disconnect() gets the au0828_dev struct via usb_get_intfdata,
so it needs to set up for the error paths.
Reported-by: syzbot+357d86bcb4cca1a2f572@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dvb_usb_device_exit() frees and uses the device name in that order.
Fix by storing the name in a buffer before freeing it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+26ec41e9f788b3eba396@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
After this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
alias: of:N*T*Cir-spi-ledC*
alias: of:N*T*Cir-spi-led
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
GCC complains about an apparently uninitialized variable recently
added to smsusb_init_device(). It's a false positive, but to silence
the warning this patch adds a trivial initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <lkp@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minimum, maximum, and stepsize taken from Silicon Labs reference.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Venus v4 doesn't send ALLOC_MODE property and thus parser doesn't
recognize it as dynamic buffer (for OUTPUT/OUTPUT2 type of buffers)
make it obvious in the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Patch commit de5a0bafcf ("media: venus: core: correct maximum hardware
load for sdm845") meant to increase the maximum hardware load for sdm845,
but ended up changing the one for msm8996 instead.
Fixes: de5a0bafcf ("media: venus: core: correct maximum hardware load for sdm845")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The header report return value from decoder sequence initialization is
available on CodaHx4 and CODA7541 already. Use the profile and level
identification values reported by the firmware to update codec specific
profile and level controls after sequence initialization has succeeded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a menu control is updated via s_ctrl, print the corresponding menu
entry string in addition to the numerical value it is set to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Otherwise the default initialization would always swamp the debug log.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print a single line containing the following information:
- which frame was decoded, including its type,
- if no frame was decoded, the reason (code) why
- which decoded frame was returned, copied out by either rotator or VODA,
- if no frame was returned, the reason (code) why, and
- the output queue sequence number, which is only useful in case
each queued coded buffer corresponds to exactly one frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a function to translate from V4L2 buffer flags to 'I'/'P'/'B'
characters for debug output.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This allows to use coda_debug level 2 for verbose but not quite as
verbose debug logging. Register access level logging is of limited
use anyway, as this includes busy polling of status bits.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the sensor refuses to set the format, avoid printing the error
message that no compatible format was found.
This means that the try_fmt will be less verbose.
The error will be printed only if really a format cannot be found.
Some application try all possible formats in a row (gstreamer e.g.)
which will flood the console with error messages until a working one is found.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds support for the 'button' control DO_WHITE_BALANCE
This feature will enable the ISC to compute the white balance coefficients
in a one time shot, at the user discretion.
This can be used if a color chart/grey chart is present in front of the camera.
The ISC will adjust the coefficients and have them fixed until next balance
or until sensor mode is changed.
This is particularly useful for white balance adjustment in different
lighting scenarios, and then taking photos to similar scenery.
The old auto white balance stays in place, where the ISC will adjust every
4 frames to the current scenery lighting, if the scenery is approximately
grey in average, otherwise grey world algorithm fails.
One time white balance adjustments needs streaming to be enabled, such that
capture is enabled and the histogram has data to work with.
Histogram without capture does not work in this hardware module.
To start the one time white balance procedure:
v4l2-ctl --set-ctrl=do_white_balance=1
This feature works only if the sensor is streaming RAW data, as the hardware
supports a histogram only for RAW bayer components.
If the auto white balance is enabled, do_white_balance does nothing.
If the streaming is disabled, or the sensor does not output RAW data, the
control is inactive.
User controls now include the do_white_balance ctrl:
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=256 value=256 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=2 step=1 default=2 value=2 flags=slider
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Control DO_WHITE_BALANCE is a button, with read only and execute-on-write flags.
Adding this control in the proper list in the fill function.
After adding it here, we can see output of v4l2-ctl -L
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reworked auto white balance feature (awb) to cope with all four channels.
Implemented stretching and grey world algorithms.
Using the histogram, the ISC will auto adjust the white balance during
frame captures.
Because each histogram needs a frame, it will take 4 frames for one adjustment.
When the gains were updated by previous code, the registers for the gains
were updated only on new streaming start. Now, after each full histogram the
registers are updated with new gains.
Also, on previous code, if the streaming stopped but not all 3 histograms
finished, a new histogram was started either way. This used to lead to an
error "timeout to update profile" when streaming was stopped.
According to the hardware, histogram can only work together with the capture,
not independently.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.917228456@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller USB fuzzer found a general-protection-fault bug in the
smsusb part of the Siano DVB driver. The fault occurs during probe
because the driver assumes without checking that the device has both
IN and OUT endpoints and the IN endpoint is ep1.
By slightly rearranging the driver's initialization code, we can make
the appropriate checks early on and thus avoid the problem. If the
expected endpoints aren't present, the new code safely returns -ENODEV
from the probe routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+53f029db71c19a47325a@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=M94t
-----END PGP SIGNATURE-----
Merge tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some fixes for some platform drivers (rockchip, atmel, omap, daVinci,
tegra-cec, coda and rcar).
Also includes a fix on one of the V4L2 uAPI doc, explaining a border
case"
* tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rockchip/vpu: Fix/re-order probe-error/remove path
media: rockchip/vpu: Initialize mdev->bus_info
media: rockchip/vpu: Get vdev from the file arg in vidioc_querycap()
media: rockchip/vpu: Add missing dont_use_autosuspend() calls
media: rockchip/vpu: Do not request id 0 for our video device
media: tegra-cec: fix cec_notifier_parse_hdmi_phandle return check
media: davinci/vpbe: array underflow in vpbe_enum_outputs()
media: field-order.rst: clarify FIELD_ANY and FIELD_NONE
media: staging/imx: add media device to capture register
media: rcar-csi2: Propagate the FLD signal for NTSC and PAL
media: rcar-csi2: restart CSI-2 link if error is detected
media: omap_vout: potential buffer overflow in vidioc_dqbuf()
media: coda: fix unset field and fail on invalid field in buf_prepare
media: atmel: atmel-isc: fix asd memory allocation
media: atmel: atmel-isc: fix INIT_WORK misplacement
media: atmel: atmel-isc: limit incoming pixels per frame
Convert to use vm_map_pages() to map range of kernel memory to user vma.
vm_pgoff is treated in V4L2 API as a 'cookie' to select a buffer, not as a
in-buffer offset by design and it always want to mmap a whole buffer from
its beginning.
Link: http://lkml.kernel.org/r/a953fe6b3056de1cc6eab654effdd4a22f125375.1552921225.git.jrdr.linux@gmail.com
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pach series "Add FOLL_LONGTERM to GUP fast and use it".
HFI1, qib, and mthca, use get_user_pages_fast() due to its performance
advantages. These pages can be held for a significant time. But
get_user_pages_fast() does not protect against mapping FS DAX pages.
Introduce FOLL_LONGTERM and use this flag in get_user_pages_fast() which
retains the performance while also adding the FS DAX checks. XDP has also
shown interest in using this functionality.[1]
In addition we change get_user_pages() to use the new FOLL_LONGTERM flag
and remove the specialized get_user_pages_longterm call.
[1] https://lkml.org/lkml/2019/3/19/939
"longterm" is a relative thing and at this point is probably a misnomer.
This is really flagging a pin which is going to be given to hardware and
can't move. I've thought of a couple of alternative names but I think we
have to settle on if we are going to use FL_LAYOUT or something else to
solve the "longterm" problem. Then I think we can change the flag to a
better name.
Secondly, it depends on how often you are registering memory. I have
spoken with some RDMA users who consider MR in the performance path...
For the overall application performance. I don't have the numbers as the
tests for HFI1 were done a long time ago. But there was a significant
advantage. Some of which is probably due to the fact that you don't have
to hold mmap_sem.
Finally, architecturally I think it would be good for everyone to use
*_fast. There are patches submitted to the RDMA list which would allow
the use of *_fast (they reworking the use of mmap_sem) and as soon as they
are accepted I'll submit a patch to convert the RDMA core as well. Also
to this point others are looking to use *_fast.
As an aside, Jasons pointed out in my previous submission that *_fast and
*_unlocked look very much the same. I agree and I think further cleanup
will be coming. But I'm focused on getting the final solution for DAX at
the moment.
This patch (of 7):
This patch starts a series which aims to support FOLL_LONGTERM in
get_user_pages_fast(). Some callers who would like to do a longterm (user
controlled pin) of pages with the fast variant of GUP for performance
purposes.
Rather than have a separate get_user_pages_longterm() call, introduce
FOLL_LONGTERM and change the longterm callers to use it.
This patch does not change any functionality. In the short term
"longterm" or user controlled pins are unsafe for Filesystems and FS DAX
in particular has been blocked. However, callers of get_user_pages_fast()
were not "protected".
FOLL_LONGTERM can _only_ be supported with get_user_pages[_fast]() as it
requires vmas to determine if DAX is in use.
NOTE: In merging with the CMA changes we opt to change the
get_user_pages() call in check_and_migrate_cma_pages() to a call of
__get_user_pages_locked() on the newly migrated pages. This makes the
code read better in that we are calling __get_user_pages_locked() on the
pages before and after a potential migration.
As a side affect some of the interfaces are cleaned up but this is not the
primary purpose of the series.
In review[1] it was asked:
<quote>
> This I don't get - if you do lock down long term mappings performance
> of the actual get_user_pages call shouldn't matter to start with.
>
> What do I miss?
A couple of points.
First "longterm" is a relative thing and at this point is probably a
misnomer. This is really flagging a pin which is going to be given to
hardware and can't move. I've thought of a couple of alternative names
but I think we have to settle on if we are going to use FL_LAYOUT or
something else to solve the "longterm" problem. Then I think we can
change the flag to a better name.
Second, It depends on how often you are registering memory. I have spoken
with some RDMA users who consider MR in the performance path... For the
overall application performance. I don't have the numbers as the tests
for HFI1 were done a long time ago. But there was a significant
advantage. Some of which is probably due to the fact that you don't have
to hold mmap_sem.
Finally, architecturally I think it would be good for everyone to use
*_fast. There are patches submitted to the RDMA list which would allow
the use of *_fast (they reworking the use of mmap_sem) and as soon as they
are accepted I'll submit a patch to convert the RDMA core as well. Also
to this point others are looking to use *_fast.
As an asside, Jasons pointed out in my previous submission that *_fast and
*_unlocked look very much the same. I agree and I think further cleanup
will be coming. But I'm focused on getting the final solution for DAX at
the moment.
</quote>
[1] https://lore.kernel.org/lkml/20190220180255.GA12020@iweiny-DESK2.sc.intel.com/T/#md6abad2569f3bf6c1f03686c8097ab6563e94965
[ira.weiny@intel.com: v3]
Link: http://lkml.kernel.org/r/20190328084422.29911-2-ira.weiny@intel.com
Link: http://lkml.kernel.org/r/20190328084422.29911-2-ira.weiny@intel.com
Link: http://lkml.kernel.org/r/20190317183438.2057-2-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
-----BEGIN PGP SIGNATURE-----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=zjhI
-----END PGP SIGNATURE-----
Merge tag 'media/v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove the deprecated Zoran driver from staging
- new I2C driver: ST MIPID02 CSI-2 camera bridge
- new platform driver: Amlogic Meson AO CEC G12A Controller
- add support for USB audio via the media controller
- au0828 driver is now supported via the media controller on both on
media and on usbaudio
- new kernel test for the media device allocator
- add support for stateless decoder at vicodec driver
- lots of other driver improvements fixes and cleanups
* tag 'media/v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (218 commits)
media: dt-bindings: aspeed-video: Add missing memory-region property
media: platform: Aspeed: Make reserved memory optional
media: platform: Aspeed: Remove use of reset line
media: stm32-dcmi: return appropriate error codes during probe
media: vsp1: Add support for missing 16-bit RGB555 formats
media: vsp1: Add support for missing 16-bit RGB444 formats
media: vsp1: Add support for missing 32-bit RGB formats
media: v4l: Add definitions for missing 16-bit RGB555 formats
media: v4l: Add definitions for missing 16-bit RGB4444 formats
media: v4l: Add definitions for missing 32-bit RGB formats
media: zoran: remove deprecated driver
media: MAINTAINERS: Update AO CEC with ao-cec-g12a driver
media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver
media: dt-bindings: media: meson-ao-cec: Add G12A AO-CEC-B Compatible
media: cros-ec-cec: decrement HDMI device refcount
media: seco-cec: decrement HDMI device refcount
media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper
media: stih_cec: use new cec_notifier_parse_hdmi_phandle helper
media: s5p_cec: use new cec_notifier_parse_hdmi_phandle helper
media: meson: ao-cec: use new cec_notifier_parse_hdmi_phandle helper
...
cec_notifier_parse_hdmi_phandle returns an error pointer, not a NULL
pointer on error.
Fixes: 4d34c9267d: ("media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In vpbe_enum_outputs() we check if (temp_index >= cfg->num_outputs) but
the problem is that "temp_index" can be negative. This patch changes
the types to unsigned to address this array underflow bug.
Fixes: 66715cdc32 ("[media] davinci vpbe: VPBE display driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on which video standard is used the driver needs to setup the
hardware to correctly handle fields. If stream is identified as NTSC
or PAL setup field detection and propagate the field detection signal.
Later versions of the datasheet have been updated to make it clear
that FLD register should be set to 0 when dealing with non-interlaced
field formats.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Restart the CSI-2 link if the CSI-2 receiver detects an error during
reception. The driver did nothing when a link error happened and the
data flow simply stopped without the user knowing why.
Change the driver to try and recover from errors by restarting the link
and informing the user that something is not right. For obvious reasons
it's not possible to recover from all errors (video source disconnected
for example) but in such cases the user is at least informed of the
error and the same behavior of the stopped data flow is retained.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The "b->index" is a u32 the comes from the user in the ioctl. It hasn't
been checked. We aren't supposed to use it but we're instead supposed
to use the value that gets written to it when we call videobuf_dqbuf().
The videobuf_dqbuf() first memsets it to zero and then re-initializes it
inside the videobuf_status() function. It's this final value which we
want.
Hans Verkuil pointed out that we need to check the return from
videobuf_dqbuf(). I ended up doing a little cleanup related to that as
well.
Fixes: 72915e851d ("[media] V4L2: OMAP: VOUT: dma map and unmap v4l2 buffers in qbuf and dqbuf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance likes to queue a buffer with field set to V4L2_FIELD_ANY
and expects it to be returned corrected to a valid field.
Follow vicodec in handling this in the buf_prepare callback.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The subsystem will free the asd memory on notifier cleanup, if the asd is
added to the notifier.
However the memory is freed using kfree.
Thus, we cannot allocate the asd using devm_*
This can lead to crashes and problems.
To test this issue, just return an error at probe, but cleanup the
notifier beforehand.
Fixes: 106267444f ("[media] atmel-isc: add the Image Sensor Controller code")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the completion function failes, unbind will be called
which will call cancel_work for awb_work.
This will trigger a WARN message from the workqueue.
To avoid this, move the INIT_WORK call at the start of the completion
function. This way the work is always initialized, which corresponds
to the 'always canceled' unbind code.
Fixes: 93d4a26c3d ("[media] atmel-isc: add the isc pipeline function")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will limit the incoming pixels per frame from the sensor.
Currently, the ISC will stop sampling the frame only when the vsync/hsync
are detected.
If we misconfigure the resolution in the sensor w.r.t. resolution in the ISC,
the buffer used for DMA in the ISC will be smaller than the number of pixels
that the ISC DMA engine will copy.
In this case it happens that the DMA will overwrite parts of the memory which
should not be written, leading to memory corruption.
To avoid this situation, use the PFE CFG1 and PFE CFG2 registers, which crop
the incoming frame to the resolution that we configure.
This way the DMA engine will never write more data than we expect it to.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Pull vfs 'struct file' related updates from Al Viro:
"A bit more of 'this fget() would be better off as fdget()'
whack-a-mole + a couple of ->f_count-related cleanups"
* 'work.file' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
media: switch to fdget()
drm_syncobj: switch to fdget()
amdgpu: switch to fdget()
don't open-code file_count()
fs: drop unused fput_atomic definition
https://lore.kernel.org/linux-fsdevel/CAHk-=wg1tFzcaX2v9Z91vPJiBR486ddW5MtgDL02-fOen2F0Aw@mail.gmail.com/T/#m5b2d9ad3aeacea4bd6aa1964468ac074bf3aa5bf
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEECVWwJCUO7/z+QjZbZsp4hBP2dUkFAlzR1UgQHGtpcnJAbmV4
ZWRpLmNvbQAKCRBmyniEE/Z1SZBiEACGw1LzUmjV9eBYFjqaUkgX/Zfcu42D4Ek2
8MuWnNdRabtpGQq0LccYlfoL3yH5xECp14IkCgJvkjqoZ3CcqWcv6uDxf0WtnUqZ
wPx1RYZykb4RZj2A6/ndhInReP4AlXICyTVulKb+BquVkemMvmXX8k+bkr/msKfT
9jdKWFIn+ANNABt3y2D7ywZvs9mkxIx+Fti+tVV4BFBeGfUuj4ArZBOHnngRnIk/
XYlQ7FVzENSPSB+3GvL34jTGEzo8suPHKhHQlIhtcd5hwzVRZKE2sdVXsCc6/WbY
YnT32gmT1/+cUuDl1mZSiQY5R4Xkb07k6/jNrdmjQpwmWbZu90cuRhb+JBXwnmjZ
2Wgy3sfwYISDxtePukg1iYePlHlVlGTYqMo3AQrTBs/gEwCKWrsKQb98mRxlf1YK
e2mdtmq6upYoorLFQesfRgrCg4GTBiPkrR3amXsFgJ2O5fhV6R98ZdGSv4kip19f
ZNoc/t1EtKGwyAJwjINduv36E3RSHODWwSPtSnmSS1ieCGToY1SI3bVUkFM4C0tO
5GMdSugHgXRGGVbTd/VftndJm6Wtj8b1j8c/1Vh04Q8qbKKJDRTDzAbK1v8oLaDh
UXAKMIc8uY4caZy3/bTAB2Ou9dibrSi8Oc+LwZqJlwIcbkwn/IGNvmwtWv4ehorE
N7EhCFZsFQ==
=Mavg
-----END PGP SIGNATURE-----
Merge tag 'stream_open-5.2' of https://lab.nexedi.com/kirr/linux
Pull stream_open conversion from Kirill Smelkov:
- remove unnecessary double nonseekable_open from drivers/char/dtlk.c
as noticed by Pavel Machek while reviewing nonseekable_open ->
stream_open mass conversion.
- the mass conversion patch promised in commit 10dce8af34 ("fs:
stream_open - opener for stream-like files so that read and write can
run simultaneously without deadlock") and is automatically generated
by running
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci
I've verified each generated change manually - that it is correct to
convert - and each other nonseekable_open instance left - that it is
either not correct to convert there, or that it is not converted due
to current stream_open.cocci limitations. More details on this in the
patch.
- finally, change VFS to pass ppos=NULL into .read/.write for files
that declare themselves streams. It was suggested by Rasmus Villemoes
and makes sure that if ppos starts to be erroneously used in a stream
file, such bug won't go unnoticed and will produce an oops instead of
creating illusion of position change being taken into account.
Note: this patch does not conflict with "fuse: Add FOPEN_STREAM to
use stream_open()" that will be hopefully coming via FUSE tree,
because fs/fuse/ uses new-style .read_iter/.write_iter, and for these
accessors position is still passed as non-pointer kiocb.ki_pos .
* tag 'stream_open-5.2' of https://lab.nexedi.com/kirr/linux:
vfs: pass ppos=NULL to .read()/.write() of FMODE_STREAM files
*: convert stream-like files from nonseekable_open -> stream_open
dtlk: remove double call to nonseekable_open
Using scripts/coccinelle/api/stream_open.cocci added in 10dce8af34
("fs: stream_open - opener for stream-like files so that read and write
can run simultaneously without deadlock"), search and convert to
stream_open all in-kernel nonseekable_open users for which read and
write actually do not depend on ppos and where there is no other methods
in file_operations which assume @offset access.
I've verified each generated change manually - that it is correct to convert -
and each other nonseekable_open instance left - that it is either not correct
to convert there, or that it is not converted due to current stream_open.cocci
limitations. The script also does not convert files that should be valid to
convert, but that currently have .llseek = noop_llseek or generic_file_llseek
for unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Among cases converted 14 were potentially vulnerable to read vs write deadlock
(see details in 10dce8af34):
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/infiniband/core/user_mad.c:988:1-17: ERROR: umad_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/misc/uinput.c:401:1-17: ERROR: uinput_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
and the rest were just safe to convert to stream_open because their read and
write do not use ppos at all and corresponding file_operations do not
have methods that assume @offset file access(*):
arch/powerpc/platforms/52xx/mpc52xx_gpt.c:631:8-24: WARNING: mpc52xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/um/drivers/harddog_kern.c:88:8-24: WARNING: harddog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/x86/kernel/cpu/microcode/core.c:430:33-49: WARNING: microcode_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ds1620.c:215:8-24: WARNING: ds1620_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/dtlk.c:301:1-17: WARNING: dtlk_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ipmi/ipmi_watchdog.c:840:9-25: WARNING: ipmi_wdog_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/pcmcia/scr24x_cs.c:95:8-24: WARNING: scr24x_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/tb0219.c:246:9-25: WARNING: tb0219_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/firewire/nosy.c:306:8-24: WARNING: nosy_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/fschmd.c:840:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/w83793.c:1344:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucma.c:1747:8-24: WARNING: ucma_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucm.c:1178:8-24: WARNING: ucm_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/uverbs_main.c:1086:8-24: WARNING: uverbs_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/input/joydev.c:282:1-17: WARNING: joydev_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/pci/switch/switchtec.c:393:1-17: WARNING: switchtec_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/platform/chrome/cros_ec_debugfs.c:135:8-24: WARNING: cros_ec_console_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-ds1374.c:470:9-25: WARNING: ds1374_wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-m41t80.c:805:9-25: WARNING: wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/tape_char.c:293:2-18: WARNING: tape_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/zcore.c:194:8-24: WARNING: zcore_reipl_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/crypto/zcrypt_api.c:528:8-24: WARNING: zcrypt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/spi/spidev.c:594:1-17: WARNING: spidev_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/staging/pi433/pi433_if.c:974:1-17: WARNING: pi433_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/acquirewdt.c:203:8-24: WARNING: acq_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/advantechwdt.c:202:8-24: WARNING: advwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim1535_wdt.c:252:8-24: WARNING: ali_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim7101_wdt.c:217:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ar7_wdt.c:166:8-24: WARNING: ar7_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/at91rm9200_wdt.c:113:8-24: WARNING: at91wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ath79_wdt.c:135:8-24: WARNING: ath79_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/bcm63xx_wdt.c:119:8-24: WARNING: bcm63xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpu5wdt.c:143:8-24: WARNING: cpu5wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpwd.c:397:8-24: WARNING: cpwd_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/eurotechwdt.c:319:8-24: WARNING: eurwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/f71808e_wdt.c:528:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/gef_wdt.c:232:8-24: WARNING: gef_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/geodewdt.c:95:8-24: WARNING: geodewdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ib700wdt.c:241:8-24: WARNING: ibwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ibmasr.c:326:8-24: WARNING: asr_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/indydog.c:80:8-24: WARNING: indydog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/intel_scu_watchdog.c:307:8-24: WARNING: intel_scu_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/iop_wdt.c:104:8-24: WARNING: iop_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/it8712f_wdt.c:330:8-24: WARNING: it8712f_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ixp4xx_wdt.c:68:8-24: WARNING: ixp4xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ks8695_wdt.c:145:8-24: WARNING: ks8695wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/m54xx_wdt.c:88:8-24: WARNING: m54xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/machzwd.c:336:8-24: WARNING: zf_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mixcomwd.c:153:8-24: WARNING: mixcomwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mtx-1_wdt.c:121:8-24: WARNING: mtx1_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mv64x60_wdt.c:136:8-24: WARNING: mv64x60_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nuc900_wdt.c:134:8-24: WARNING: nuc900wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nv_tco.c:164:8-24: WARNING: nv_tco_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pc87413_wdt.c:289:8-24: WARNING: pc87413_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:698:8-24: WARNING: pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:737:8-24: WARNING: pcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:581:8-24: WARNING: pcipcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:623:8-24: WARNING: pcipcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:488:8-24: WARNING: usb_pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:527:8-24: WARNING: usb_pcwd_temperature_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pika_wdt.c:121:8-24: WARNING: pikawdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pnx833x_wdt.c:119:8-24: WARNING: pnx833x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rc32434_wdt.c:153:8-24: WARNING: rc32434_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rdc321x_wdt.c:145:8-24: WARNING: rdc321x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/riowd.c:79:1-17: WARNING: riowd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sa1100_wdt.c:62:8-24: WARNING: sa1100dog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc60xxwdt.c:211:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc7240_wdt.c:139:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc8360.c:274:8-24: WARNING: sbc8360_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_epx_c3.c:81:8-24: WARNING: epx_c3_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_fitpc2_wdt.c:78:8-24: WARNING: fitpc2_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sb_wdog.c:108:1-17: WARNING: sbwdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc1200wdt.c:181:8-24: WARNING: sc1200wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc520_wdt.c:261:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sch311x_wdt.c:319:8-24: WARNING: sch311x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/scx200_wdt.c:105:8-24: WARNING: scx200_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/smsc37b787_wdt.c:369:8-24: WARNING: wb_smsc_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83877f_wdt.c:227:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83977f_wdt.c:301:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wafer5823wdt.c:200:8-24: WARNING: wafwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/watchdog_dev.c:828:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:379:8-24: WARNING: wdrtas_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:445:8-24: WARNING: wdrtas_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt285.c:104:1-17: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt977.c:276:8-24: WARNING: wdt977_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:424:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:484:8-24: WARNING: wdt_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:464:8-24: WARNING: wdtpci_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:527:8-24: WARNING: wdtpci_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
net/batman-adv/log.c:105:1-17: WARNING: batadv_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/control.c:57:7-23: WARNING: snd_ctl_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/rawmidi.c:385:7-23: WARNING: snd_rawmidi_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/seq/seq_clientmgr.c:310:7-23: WARNING: snd_seq_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/timer.c:1428:7-23: WARNING: snd_timer_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
One can also recheck/review the patch via generating it with explanation comments included via
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci SPFLAGS="-D explain"
(*) This second group also contains cases with read/write deadlocks that
stream_open.cocci don't yet detect, but which are still valid to convert to
stream_open since ppos is not used. For example drivers/pci/switch/switchtec.c
calls wait_for_completion_interruptible() in its .read, but stream_open.cocci
currently detects only "wait_event*" as blocking.
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yongzhi Pan <panyongzhi@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Nikolaus Rath <Nikolaus@rath.org>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James R. Van Zandt" <jrv@vanzandt.mv.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk> [scr24x_cs]
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Jean Delvare <jdelvare@suse.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> [watchdog/* hwmon/*]
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com> [drivers/pci/switch/switchtec]
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [drivers/pci/switch/switchtec]
Cc: Benson Leung <bleung@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> [platform/chrome]
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> [rtc/*]
Cc: Mark Brown <broonie@kernel.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Zwane Mwaikambo <zwanem@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Reserved memory doesn't need to be required; system memory would work
fine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The reset line is toggled by enabling the clocks, so it's not necessary
to manually toggle the reset as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During probe, return the provided errors value instead of -ENODEV.
This allows the driver to be deferred probed if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_RGBA555, V4L2_PIX_FMT_RGBX555,
V4L2_PIX_FMT_ABGR555, V4L2_PIX_FMT_XBGR555, V4L2_PIX_FMT_BGRA555 and
V4L2_PIX_FMT_BGRX555 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_RGBA444, V4L2_PIX_FMT_RGBX444,
V4L2_PIX_FMT_ABGR444, V4L2_PIX_FMT_XBGR444, V4L2_PIX_FMT_BGRA444 and
V4L2_PIX_FMT_BGRX444 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_BGRA32, V4L2_PIX_FMT_BGRX32,
V4L2_PIX_FMT_RGBA32 and V4L2_PIX_FMT_RGBX32 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Amlogic G12A SoC embeds a second CEC controller with a totally
different design.
The two controller can work in the same time since the CEC line can
be set to two different pins on the two controllers.
This second CEC controller is documented as "AO-CEC-B", thus the
registers will be named "CECB_" to differentiate with the other
AO-CEC driver.
Unlike the other AO-CEC controller, this one takes the Oscillator
clock as input and embeds a dual-divider to provide a precise
32768Hz clock for communication. This is handled by registering
a clock in the driver.
Unlike the other AO-CEC controller, this controller supports setting
up to 15 logical addresses and supports the signal_free_time settings
in the transmit function.
Unfortunately, this controller does not support "monitor" mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CrosEC CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SECO CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tegra CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The STI CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The S5P CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The meson CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add helper function to parse the DT for the hdmi-phandle property
and return the corresponding struct device pointer.
It takes care to avoid increasing the device refcount since all
we need is the device pointer. This pointer is used in the
notifier list as a key, but it is never accessed by the CEC driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I previously added an RC_CORE dependency here, but missed the corner
case of CONFIG_VIDEO_SECO_CEC=y with CONFIG_RC_CORE=m, which still
causes a link error:
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_probe':
seco-cec.c:(.text+0x1b8): undefined reference to `devm_rc_allocate_device'
seco-cec.c:(.text+0x2e8): undefined reference to `devm_rc_register_device'
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_irq_handler':
seco-cec.c:(.text+0xa2c): undefined reference to `rc_keydown'
Refine the dependency to disallow building the RC subdriver in this case.
This is the same logic we apply in other drivers like it.
Fixes: f27dd0ad68 ("media: seco-cec: fix RC_CORE dependency")
Cc: <stable@vger.kernel.org> # 5.1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In function ts2020_set_tuner_rf(), local variable "utmp" could
be uninitialized if function regmap_read() returns -EINVAL.
However, this value is used in if statement and written to
the register, which is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The timestamps in ir-keytable -t output showed that the Xbox DVD
IR dongle decodes scancodes every 64ms. The last scancode of a
longer button press is decodes 64ms after the last-but-one which
indicates the decoder doesn't use a timeout but decodes on the last
edge of the signal.
267.042629: lirc protocol(unknown): scancode = 0xace
267.042665: event type EV_MSC(0x04): scancode = 0xace
267.042665: event type EV_KEY(0x01) key_down: KEY_1(0x0002)
267.042665: event type EV_SYN(0x00).
267.106625: lirc protocol(unknown): scancode = 0xace
267.106643: event type EV_MSC(0x04): scancode = 0xace
267.106643: event type EV_SYN(0x00).
267.170623: lirc protocol(unknown): scancode = 0xace
267.170638: event type EV_MSC(0x04): scancode = 0xace
267.170638: event type EV_SYN(0x00).
267.234621: lirc protocol(unknown): scancode = 0xace
267.234636: event type EV_MSC(0x04): scancode = 0xace
267.234636: event type EV_SYN(0x00).
267.298623: lirc protocol(unknown): scancode = 0xace
267.298638: event type EV_MSC(0x04): scancode = 0xace
267.298638: event type EV_SYN(0x00).
267.543345: event type EV_KEY(0x01) key_down: KEY_1(0x0002)
267.543345: event type EV_SYN(0x00).
267.570015: event type EV_KEY(0x01) key_up: KEY_1(0x0002)
267.570015: event type EV_SYN(0x00).
Add a protocol with the repeat value and set the timeout in the
driver to 10ms (to have a bit of headroom for delays) so the Xbox
DVD remote performs more responsive.
Signed-off-by: Matthias Reichl <hias@horus.com>
Acked-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later datasheet versions (rev 1.00) clarifies that the FLD register
should be set after LINKCNT.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Latest information from hardware engineers reveals that H3 ES2 and ES3
behave differently when working with link speeds bellow 250 Mpbs.
Add a SoC match for H3 ES2.* and use the correct startup sequence.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The latest datasheet (rev 1.50) updates the start procedure for V3M and
E3. Update the driver to match these changes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later versions of the datasheet updates the reset procedure to more
closely resemble the standby mode. Update the driver to enter and exit
the standby mode instead of resetting the hardware before and after
streaming is started and stopped. This replaces the software reset
(SRST.SRST) control.
While at it break out the full start and stop procedures from
rcsi2_s_stream() into the existing helper functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If VIDIOC_CREATE_BUFS is called with a sizeimage smaller than the
queue sizeimage, fail with -EINVAL instead of correcting the size
and continuing without error. This is required by v4l2-compliance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance sets colorimetry on the output queue and then verifies
that querying colorimetry on the capture queue returns the same
configuration. For this to work, the encoder must allow setting context
colorimetry parameters on the output queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful encoder API requires VIDIOC_ENUM_FRAMESIZES to be
implemented.
Allow enumeration of supported frame sizes for encoding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return -ENOTTY when userspace tries to call VIDIOC_(TRY_)ENCODER_CMD on
a decoder instance or VIDIOC_(TRY_)DECODER_CMD on an encoder instance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add min number of buffers for capture (decoder) and output (encoder)
controls, which are required by the stateful video decoder / encoder
interface specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error return value is not written by some firmware codecs, such as
MPEG-2 decode on CodaHx4. Clear the error return value before starting
the picture run to avoid misinterpreting unrelated values returned by
sequence initialization as error return value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since levels are specified in terms of maximum values, there is no
reason to filter out lower levels than the supported maximum.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chosen codec depends on the coded format, which is known as soon as
the S_FMT call on the coded queue. This allows to use the codec in
callbacks that may be called before start_streaming, such as buf_queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Calling VIDIOC_DQBUF can release the core serialization lock pointed to
by vb2_queue->lock if it has to wait for a new buffer to arrive.
However, if userspace dup()ped the video device filehandle, then it is
possible to read or call DQBUF from two filehandles at the same time.
It is also possible to call REQBUFS from one filehandle while the other
is waiting for a buffer. This will remove all the buffers and reallocate
new ones. Removing all the buffers isn't the problem here (that's already
handled correctly by DQBUF), but the reallocating part is: DQBUF isn't
aware that the buffers have changed.
This is fixed by setting a flag whenever the lock is released while waiting
for a buffer to arrive. And checking the flag where needed so we can return
-EBUSY.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Syzbot <syzbot+4180ff9ca6810b06c1e9@syzkaller.appspotmail.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ctrl_check_input() function is called from pvr2_ctrl_range_check().
It's supposed to validate user supplied input and return true or false
depending on whether the input is valid or not. The problem is that
negative shifts or shifts greater than 31 are undefined in C. In
practice with GCC they result in shift wrapping so this function returns
true for some inputs which are not valid and this could result in a
buffer overflow:
drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname()
warn: uncapped user index 'names[val]'
The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create()
and the highest valid bit is BIT(4).
Fixes: 7fb20fa38c ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a buffer is queued to a request, followed by an attempt to queue
the same buffer again, then the second qbuf returns an error since
the buffer is not in the DEQUEUED state anymore.
However, before it gets to that check it executes the code under the
'if (!vb->prepared)' condition. This clears previously set data needed
for request handling, and now querybuf will no longer report that this
buffer is part of a request.
Move the state check to before the 'if' and make sure to only do the
state check when called from QBUF and if V4L2_BUF_FLAG_REQUEST_FD is
set.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Update referenced frame buffer's reference count when playing vp9
content which has show_existing_frame flag, and copy enough buffer
data to current shown frame.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver returns an error if unsupported media bus pixel code is
requested by VIDIOC_SUBDEV_S_FMT.
But according to Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst,
Drivers must not return an error solely because the requested format
doesn't match the device capabilities. They must instead modify the
format to match what the hardware can provide.
So select default format code and return success in that case.
This is detected by v4l2-compliance.
Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Register V4L2 subdevice implemented by the driver to the V4L2
asynchronous subdevice framework.
[Sakari Ailus: Remove extra call to v4l2_i2c_subdev_set_name]
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation for adding asynchronous subdevice support to the driver,
don't acquire v4l2_clk from the driver .probe() callback as that may
fail if the clock is provided by a bridge driver which may be not yet
initialized. Move the v4l2_clk_get() to ov6650_video_probe() helper
which is going to be converted to v4l2_subdev_internal_ops.registered()
callback, executed only when the bridge driver is ready.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After removal of clock_start() from before soc_camera_init_i2c() in
soc_camera_probe() by commit 9aea470b39 ("[media] soc-camera: switch
I2C subdevice drivers to use v4l2-clk") introduced in v3.11, the ov6650
driver could no longer probe the sensor successfully because its clock
was no longer turned on in advance. The issue was initially worked
around by adding that missing clock_start() equivalent to OMAP1 camera
interface driver - the only user of this sensor - but a propoer fix
should be rather implemented in the sensor driver code itself.
Fix the issue by inserting a delay between the clock is turned on and
the sensor I2C registers are read for the first time.
Tested on Amstrad Delta with now out of tree but still locally
maintained omap1_camera host driver.
Fixes: 9aea470b39 ("[media] soc-camera: switch I2C subdevice drivers to use v4l2-clk")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the application was streaming from both videoX and vbiX, and streaming
from videoX was stopped, then the vbi streaming also stopped.
The cause being that stop_streaming for video stopped the subdevs as well,
instead of only doing that if dev->streaming_users reached 0.
au0828_stop_vbi_streaming was also wrong since it didn't stop the subdevs
at all when dev->streaming_users reached 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enable and disable source interfaces aren't consistent in enforcing
how video and audio share the tuner resource.
Fix these issues to enforce the following rules and allow
sharing between audio and video applications.
- When DVB is streaming, audio/video/vbi/s-video/composite
should find the resource busy. DVB holds the tuner in
exclusive mode.
- When video/VBI is streaming, audio can share the tuner and vice versa.
- v4l2 allows multiple applications to open video device.
- Video applications call enable source multiple times during their
run-time. Resource should stay locked until the last application
releases it.
- A shared resource should stay in shared state and locked when it is
in use by audio and video. More than one video application is allowed
to use the tuner as long as video streaming protocol allows such usage.
Resource is released when the last video/audio application releases it.
- S-Video and Composite hold the resource in exclusive mode.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media Device Allocator API to allows multiple drivers share a media device.
This API solves a very common use-case for media devices where one physical
device (an USB stick) provides both audio and video. When such media device
exposes a standard USB Audio class, a proprietary Video class, two or more
independent drivers will share a single physical USB bridge. In such cases,
it is necessary to coordinate access to the shared resource.
Using this API, drivers can allocate a media device with the shared struct
device as the key. Once the media device is allocated by a driver, other
drivers can get a reference to it. The media device is released when all
the references are released.
Change au0828 to use Media Device Allocator API to allocate media device
with the parent usb struct device as the key, so it can be shared with the
snd_usb_audio driver.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media Device Allocator API to allows multiple drivers share a media device.
This API solves a very common use-case for media devices where one physical
device (an USB stick) provides both audio and video. When such media device
exposes a standard USB Audio class, a proprietary Video class, two or more
independent drivers will share a single physical USB bridge. In such cases,
it is necessary to coordinate access to the shared resource.
Using this API, drivers can allocate a media device with the shared struct
device as the key. Once the media device is allocated by a driver, other
drivers can get a reference to it. The media device is released when all
the references are released.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not access sd_formats[] if num_of_sd_formats is zero, ie
subdev sensor didn't expose any formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Report overrun error only when it exceeds a given threshold.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several places where a break statement occurs before
a following break statement; these are unnecessary and can be
removed to clean up the code a little.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enlarge the plane number to support more complex case
and add the support for fmt change case.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media bus codes were being mapped to pixelformats, which causes a
limitation on vimc because not all pixelformats can be mapped to media
bus codes.
Also, media bus codes are an internal configuration from the device.
Userspace only assures media bus codes matches between pads and expects
the image in a given pixelformat. So we can allow almost any media bus
format to be configured between pads, except for debayer that expects a
media bus code of type bayer in the sink pad.
[hverkuil-cisco@xs4all.nl: drop use of v4l2_get_fourcc_name: not yet available]
[hverkuil-cisco@xs4all.nl: made vimc_mbus_list static]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add bayer format information in struct v4l2_format_info table.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add two new API helpers, v4l2_fill_pixfmt and v4l2_fill_pixfmt_mp,
to be used by drivers to calculate plane sizes and bytes per lines.
Note that driver-specific padding and alignment are not
taken into account, and must be done by drivers using this API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Minor fix for helper function and comment, s/v4l2_vb2_buffer/vb2_v4l2_buffer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is mandatory to write CEC_CFGR only when CECEN=0. To protect
transmission, a check have been added to delayed logical address
modification. This patch is necessary tp pass all tests of compliance.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ISC will output the "ARGB32" configuration in byte order: B, G, R, Alpha.
This is in fact the format BGRA, aka ABGR32.
If alpha is missing, the same format is equivalent to XBGR32.
Added both formats and removed ARGB32 which is wrong.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This change is a redesign in the formats and the way the ISC is
configured w.r.t. sensor format and the output format from the ISC.
I have changed the splitting between sensor output (which is also ISC input)
and ISC output.
The sensor format represents the way the sensor is configured, and what ISC
is receiving.
The format configuration represents the way ISC is interpreting the data and
formatting the output to the subsystem.
Now it's much easier to figure out what is the ISC configuration for input, and
what is the configuration for output.
The non-raw format can be obtained directly from sensor or it can be done
inside the ISC. The controller format list will include a configuration for
each format.
The old supported formats are still in place, if we want to dump the sensor
format directly to the output, the try format routine will detect and
configure the pipeline accordingly.
This also fixes the previous issues when the raw format was NULL which
resulted in many crashes for sensors which did not have the expected/tested
formats.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add following V4L2 QP parameters for H.264:
* V4L2_CID_MPEG_VIDEO_H264_I_FRAME_MIN_QP
* V4L2_CID_MPEG_VIDEO_H264_I_FRAME_MAX_QP
* V4L2_CID_MPEG_VIDEO_H264_P_FRAME_MIN_QP
* V4L2_CID_MPEG_VIDEO_H264_P_FRAME_MAX_QP
These controls will limit QP range for intra and inter frame,
provide more manual control to improve video encode quality.
Signed-off-by: Fish Lin <linfish@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit f1a2e44a3a ("bpf: add queue and stack maps") introduced new BPF
helper functions:
- BPF_FUNC_map_push_elem
- BPF_FUNC_map_pop_elem
- BPF_FUNC_map_peek_elem
but they were made available only for network BPF programs. This patch
makes them available for tracepoint, cgroup and lirc programs.
Signed-off-by: Alban Crequy <alban@kinvolk.io>
Cc: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The exposure control is clustered with the autoexposure control and
flagged as volatile, but the g_volatile_ctrl() doesn't handle
V4L2_CID_EXPOSURE_AUTO. So, the value of the exposure control can't be
read in autoexposure mode.
This enables to get the exposure control in autoexposure mode by making
ov7740_get_volatile_ctrl() deal with V4L2_CID_EXPOSURE_AUTO.
This also sets the exposure control as volatile by specifying the
argument to v4l2_ctrl_auto_cluster() instead of manually flagging it.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of doing the cast, just change the type to char.
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().
While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The support for those two formats are archtecture-dependent.
Use the endianness to CPU macros to do it right.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The st_register() returns have changed over time, but these days it
never returns -1. We should just be checking for any negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'vb' null check should be done before dereferencing it in
tw5864_handle_frame, otherwise a NULL pointer dereference
may occur.
Fixes: 34d1324edd ("[media] pci: Add tw5864 driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case usb_alloc_coherent fails, the fix returns -ENOMEM to
avoid a potential NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_kcalloc may fail and return a null pointer. The fix returns
-ENOMEM upon failures to avoid null pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This member is never read throughout the code, so remove it.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions by changing a few local variables from vb2_buffer to
vb2_v4l2_buffer. However, it left a few accesses to vb2_buffer::planes
as-is, accidentally turning them into accesses to
vb2_v4l2_buffer::planes and resulting in values being read from/written
to the wrong place.
Fix this by inserting vb2_buf into these accesses so they mimic their
original behavior.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This code generates a static checker warning:
drivers/media/v4l2-core/v4l2-ctrls.c:2921 v4l2_querymenu()
warn: should '(1 << i)' be a 64 bit type?
The problem is that "ctrl->menu_skip_mask" is a u64 and we're only
testing the lower 32 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clang warns about a possible variable use that gcc never
complained about:
drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
[-Werror,-Wuninitialized]
dm365_vpss_set_pg_frame_size(frame_size);
^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
struct vpss_pg_frame_size frame_size;
^
1 error generated.
There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.
On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.
To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.
Fixes: 63e3ab142f ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Building tda1997x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt'
undefined reference to `v4l2_fwnode_endpoint_parse'
While at it, also sort the selections alphabetically
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: stable@vger.kernel.org # v4.17+
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to prevent ISOC URBs from being infinitely resubmitted,
the driver's USB disconnect handler must kill all the in-flight URBs.
While here, change the URB packet status message to a debug level,
to avoid spamming the console too much.
This commit fixes a lockup caused by an interrupt storm coming
from the URB completion handler.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch warns about small size on two structs:
drivers/media/platform/qcom/venus/hfi_parser.c:103 parse_profile_level() error: memcpy() 'proflevel' too small (8 vs 128)
drivers/media/platform/qcom/venus/hfi_parser.c: drivers/media/platform/qcom/venus/hfi_parser.c:129 parse_caps() error: memcpy() 'cap' too small (16 vs 512)
The reason is that the hfi_parser actually expects:
- multiple data entries on hfi_capabilities
- multiple profile_level on hfi_profile_level_supported
However, the structs trick gcc, making it to believe that
there's just one value for each.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only way for p_set to be NULL would be if vin_coef_set would be an
empty array.
On such case, the driver will OOPS, as it would try to de-reference a
NULL value. So, the check if p_set is not NULL doesn't make any sense.
Solves those two smatch warnings:
drivers/media/platform/rcar-vin/rcar-dma.c:489 rvin_set_coeff() warn: variable dereferenced before check 'p_set' (see line 484)
drivers/media/platform/rcar-vin/rcar-dma.c:494 rvin_set_coeff() error: we previously assumed 'p_set' could be null (see line 489)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the error logic, ipc_buf was already asigned to &ctx->ipc_buf_struct,
with can't be null, as warned by smatch:
drivers/media/platform/sti/delta/delta-ipc.c:223 delta_ipc_open() warn: variable dereferenced before check 'ctx->ipc_buf' (see line 183)
So, remove the uneeded check.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The way the code works, compression will be a valid value (less or equal to 3)
on both set_video_mode_foo() calls at the beginning of the while() loop.
So, the value for pChoose can't be NULL.
Solves those smatch warnings:
drivers/media/usb/pwc/pwc-ctrl.c: drivers/media/usb/pwc/pwc-ctrl.c:252 set_video_mode_Timon() warn: variable dereferenced before check 'pChoose' (see line 248)
drivers/media/usb/pwc/pwc-ctrl.c: drivers/media/usb/pwc/pwc-ctrl.c:302 set_video_mode_Kiara() warn: variable dereferenced before check 'pChoose' (see line 298)
and simplifies the code a little bit.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are some macros at cx2341x_update() with seemed to
be introduced in order to ensure that lines would be less
than 80 columns.
Well, the thing is that they make the code harder to be analized,
not only by humans, but also for static code analyzers:
drivers/media/common/cx2341x.c:1116 cx2341x_update() error: we previously assumed 'old' could be null (see line 1047)
So, remove the "force" var, and replace the NEQ macro to a
better designed one that makes clearer about what it is doing.
While here, also remove the "temporal" var, as it is just another
way of doing the same type of check as the new CMP_FIELD() macro
already does.
Finally, fix coding style at the block code.
remove such macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by smatch:
drivers/media/i2c/imx214.c:591 imx214_set_format() warn: variable dereferenced before check 'format' (see line 589)
It turns that the code at imx214_set_format() has support for being
called with the format being NULL. I've no idea why, as it is only
called internally with the pointer set, and via subdev API (with
should also set it).
Also, the entire logic there depends on having format != NULL, so
just remove the bogus broken support for a null format.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Indentation is odd in several places, especially when printing messages
to the kernel log. Fix it to match the usual coding style.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
for stateless decoder, set the output pixelformat
to V4L2_PIX_FMT_FWHT_STATELESS and the pix info to
pixfmt_stateless_fwht
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement a stateless decoder for the new node.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: add 'return 0;' before default case in vicodec_try_ctrl()]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add stateless decoder instance field to the dev struct and
register another node for the statelsess decoder.
The stateless API for the node will be implemented in further patches.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix typo: videdev-stateless-dec -> stateless-decoder]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add V4L2_PIX_FMT_FWHT_STATELESS to the list of pixelformats that
v4l_fill_fmtdesc() understands.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs and definitions needed to implement stateless
decoder for fwht and add I/P-frames QP controls to the
public api.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add struct 'vicodec_dev_instance' for the fields in vicodec_dev
that have have both decoder and encoder versions.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the stateless decoder the reference buffer is null if the
frame is an I-frame (flagged with FWHT_FL_I_FRAME).
Make sure not to dereference it in that case.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename 'v4l2_fwht_default_fmt' to 'v4l2_fwht_find_nth_fmt'
and add a function 'v4l2_fwht_validate_fmt' to check if
a format info matches the parameters.
This function will also be used to validate the stateless
params when adding support for stateless codecs.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the code that validates version dependent header
values to a separate function 'validate_by_version'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the decoder, save the inner reference frame in the same
format as the capture buffer.
The decoder writes directly to the capture buffer and then
the capture buffer is copied to the reference buffer.
This will simplify the stateless decoder.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the field 'buf' to fwht_raw_frame to indicate
the start of the raw frame buffer.
This field will be used to copy the capture buffer
to the reference buffer in the next patch.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce 'prepare_raw_frame' function that fills the values
of a raw frame struct according to the format.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'v4l2_m2m_buf_copy_metadata' should
be called even if decoding/encoding ends with
status VB2_BUF_STATE_ERROR, so that the metadata
is copied from the source buffer to the dest buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fwht_encode returns either an error code on
failure or the size of the compressed frame on
success. So change the var assigned to it from
'ret' to 'comp_sz_or_errcode' to clarify that.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If one of the controls fails to set,
then 'v4l2_ctrl_request_setup'
immediately returns with the error code.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'v4l2_m2m_ctx_release' calls request complete
so it should be called before 'v4l2_ctrl_handler_free'.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The logic of g_selection was wrong: encoders support crop,
decoders support compose, but the code allowed both.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The selection api should check only single buffer types
because multiplanar types are converted to
single in drivers/media/v4l2-core/v4l2-ioctl.c
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If requests are used when they shouldn't, or not used when they should,
then return EBADR (Invalid request descriptor) instead of EACCES.
The reason for this change is that EACCES has more to do with permissions
(not being the owner of the resource), but in this case the request file
descriptor is just wrong for the current mode of the device.
Update the documentation accordingly.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Stateless codecs require the use of the Request API as opposed of it
being optional.
So add a bit to indicate this and let vb2 check for this.
If an attempt is made to queue a buffer without an associated request,
then the EBADR error is returned to userspace.
Doing this check in the vb2 core simplifies drivers, since they
don't have to check for this, they can just set this flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is not how ACPI tables are written. Add a deprecation note and refer
to the proper documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the entity function for the four CSI-2 receiver sub-devices the driver
creates. This avoids a kernel warning from each as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The lens drivers had ended up under the video decoder section; add a new
one just for them, between the camera sensors and flash drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ti-vpe driver parsed the remote endpoints for properties but ignored the
local ones. Fix this by parsing the local endpoint properties instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
V4L2 fwnode matching right now still works based on device nodes, not port
nodes. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
C-PHY has no clock lanes. Therefore the first data lane is 0 by default.
Fixes: edc6d56c2e ("media: v4l: fwnode: Support parsing of CSI-2 C-PHY endpoints")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The lack of defaults provided by the caller to
v4l2_fwnode_endpoint_parse() signals the use of the default lane mapping.
The default lane mapping must not be used however if the firmmare contains
the lane mapping. Disable the default lane mapping in that case, and
improve the debug messages telling of the use of the defaults.
This was missed previously since the default mapping will only unsed in
this case if the bus type is set, and no driver did both while still
needing the lane mapping configuration.
Fixes: b4357d21d6 ("media: v4l: fwnode: Support default CSI-2 lane mapping for drivers")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 3d6a8fe256 ("media: ov7670: hook s_power onto v4l2 core"),
the device is actually powered off while the video stream is stopped.
So now set_format and s_frame_interval could be called while the device
is powered off, but these callbacks try to change the register settings
at this time.
The frame format and framerate will be restored right after power-up, so
we can just postpone applying these changes at these callbacks if the
device is not powered up.
Fixes: 3d6a8fe256 ("media: ov7670: hook s_power onto v4l2 core")
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 3d6a8fe256 ("media: ov7670: hook s_power onto v4l2 core"),
the device is actually powered off while the video stream is stopped.
The frame format and framerate are restored right after power-up, but
restoring the default register settings is forgotten.
Fixes: 3d6a8fe256 ("media: ov7670: hook s_power onto v4l2 core")
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming was called both last_src_buf and last_dst_buf
pointers were set to NULL, but this depends on whether the capture
or output queue starts streaming.
When decoding with resolution changes in between the capture queue
has to restart streaming whenever a resolution change occurs. And
that would reset last_src_buf as well, which causes a problem if
the decoder was stopped by the application. Since last_src_buf
is now NULL, the LAST flag is never set for the last capture
buffer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some functions like enum_fmt use the buffer type as was passed
from userspace, which might cause the switch to fall into the
default case. Just drop the WARN_ON(1) to avoid kernel log pollution.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array addr_list on the stack but instead make it
static. Makes the object code smaller by 20 bytes
Before:
text data bss dec hex filename^M
16929 3626 384 20939 51cb ../usb/em28xx/em28xx-input.o
After:
text data bss dec hex filename^M
16829 3706 384 20919 51b7 ../usb/em28xx/em28xx-input.o
(gcc version 8.3.0, aarch64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch add support for Avermedia TD310 usb stick.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
i2c bus is already needed when the frontend is probed, so init it already
in it930x_frontend_attach. That prevents errors like:
si2168: probe of 6-0067 failed with error -5
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
si2165_readreg8() may fail. Looking into si2165_readreg8(), we will find
that "val_tmp" will be an uninitialized value when regmap_read() fails.
"val_tmp" is then assigned to "val". So if si2165_readreg8() fails,
"val" will be a random value. Further use will lead to undefined
behaviors. The fix checks if si2165_readreg8() fails, and if so, returns
its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checking of kmalloc() seems to have been committed - as
cx23885_dvb_register() is checking for != 0 return, returning
-ENOMEM should be fine here. While at it address the coccicheck
suggestion to move to kmemdup rather than using kmalloc+memcpy.
Fixes: 46b21bbaa8 ("[media] Add support for DViCO FusionHDTV DVB-T Dual Express2")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=199323
Users are experiencing problems with the DVBSky S960/S960C USB devices
since the following commit:
9d659ae: ("locking/mutex: Add lock handoff to avoid starvation")
The device malfunctions after running for an indeterminable period of
time, and the problem can only be cleared by rebooting the machine.
It is possible to encourage the problem to surface by blocking the
signal to the LNB.
Further debugging revealed the cause of the problem.
In the following capture:
- thread #1325 is running m88ds3103_set_frontend
- thread #42 is running ts2020_stat_work
a> [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 07 80
[1325] usb 1-1: dvb_usb_v2_generic_io: <<< 08
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 68 3f
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 08 ff
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 07
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 3d
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff
b> [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 07 00
[1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 07
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 21
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 07
[42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 66
[42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff
[1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11
[1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07
[1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 60 02 10 0b
[1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07
Two i2c messages are sent to perform a reset in m88ds3103_set_frontend:
a. 0x07, 0x80
b. 0x07, 0x00
However, as shown in the capture, the regmap mutex is being handed over
to another thread (ts2020_stat_work) in between these two messages.
>From here, the device responds to every i2c message with an 07 message,
and will only return to normal operation following a power cycle.
Use regmap_multi_reg_write to group the two reset messages, ensuring
both are processed before the regmap mutex is unlocked.
Signed-off-by: James Hutchinson <jahutchinson99@googlemail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 14f4eaedda ("media: dvbsky: fix driver unregister logic") fixed
a use-after-free by removing the reference to the frontend after deleting
the backing i2c device.
This has the unfortunate side effect the frontend device is never freed
in the dvb core leaving a dangling device, leading to errors when the
dvb core tries to register the frontend after e.g. a replug as reported
here: https://www.spinics.net/lists/linux-media/msg138181.html
media: dvbsky: issues with DVBSky T680CI
===
[ 561.119145] sp2 8-0040: CIMaX SP2 successfully attached
[ 561.119161] usb 2-3: DVB: registering adapter 0 frontend 0 (Silicon Labs
Si2168)...
[ 561.119174] sysfs: cannot create duplicate filename '/class/dvb/
dvb0.frontend0'
===
The use after free happened as dvb_usbv2_disconnect calls in this order:
- dvb_usb_device::props->exit(...)
- dvb_usbv2_adapter_frontend_exit(...)
+ if (fe) dvb_unregister_frontend(fe)
+ dvb_usb_device::props->frontend_detach(...)
Moving the release of the i2c device from exit() to frontend_detach()
avoids the dangling pointer access and allows the core to unregister
the frontend.
This was originally reported for a DVBSky T680CI, but it also affects
the MyGica T230C. As all supported devices structure the registration/
unregistration identically, apply the change for all device types.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We forgot to set "ret" on this error path.
Fixes: e8454ff7b9 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Building adv748x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/adv748x/adv748x-core.o: In function `adv748x_probe':
adv748x-core.c:(.text+0x1b2c): undefined reference to `v4l2_fwnode_endpoint_parse'
Fixes: 6a18865da8 ("media: i2c: adv748x: store number of CSI-2 lanes described in device tree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
strscpy() returns a negative value on failure unlike strlcpy(),
so fix the WARN_ON accordingly.
Signed-off-by: Hans Petter Selasky <hps@selasky.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: added commit message]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The s_stream callback was not being called for the first entity in the
stream pipeline array.
Instead of verifying the type of the node (video or subdevice) and
calling s_stream from the second entity in the pipeline, do this process
for all the entities in the pipeline for consistency.
The previous code was not a problem because the first entity is a video
device and not a subdevice, but this patch prepares vimc to allow
setting some configuration in the entity before calling s_stream.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix line-too-long warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to have the frame field in the vimc_stream struct.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The type V4L2_FRMSIZE_TYPE_CONTINUOUS expects a step of 1.
This fixes v4l2-compliance test error:
fail: v4l2-test-formats.cpp(184): invalid step_width/height for continuous framesize
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The format of the sink pad should be a bayer mbus format.
This fixes a kernel NULL pointer dereference error that was caused when
the stream starts because the configured format was not found in the
pixelmap table.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no point to continuing assignment after memory allocation
failed, rather throw error immediately.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: rebase and remove empty line before the if]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When streaming is stopped all URBs are killed, but in fill_frame and in
bulk_irq this results in an attempt to resubmit the killed URB. That is
not what you want and causes spurious kernel messages.
So check if streaming has stopped before resubmitting.
Also check against gspca_dev->streaming rather than vb2_start_streaming_called()
since vb2_start_streaming_called() will return true when in stop_streaming,
but gspca_dev->streaming is set to false when stop_streaming is called.
Fixes: 6992effe53 ("gspca: Kill all URBs before releasing any of them")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
__media_pipeline_start() does WARN_ON() when active pipe doesn't
match the input arg entity's pipe.
Replace WARN_ON with a conditional and error message that includes
names of both entities.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang-9 makes some different inlining decisions compared to gcc, which
leads to a warning about a possible stack overflow problem when building
with CONFIG_KASAN, including when setting asan-stack=0, which avoids
most other frame overflow warnings:
drivers/media/platform/vicodec/codec-fwht.c:673:12: error: stack frame size of 2224 bytes in function 'encode_plane'
Manually adding noinline_for_stack annotations in those functions
called by encode_plane() or decode_plane() that require a significant
amount of kernel stack makes this impossible to happen with any
compiler.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We should be updating *pos. The current code is a no-op.
Fixes: 1c1e45d17b ("V4L/DVB (7786): cx18: new driver for the Conexant CX23418 MPEG encoder chip")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We had intended to update *pos, but the current code is a no-op.
Fixes: 1a0adaf37c ("V4L/DVB (5345): ivtv driver for Conexant cx23416/cx23415 MPEG encoder/decoder")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clang-8 warns about one function here when KASAN is enabled, even
without the 'asan-stack' option:
drivers/media/usb/go7007/go7007-fw.c:1551:5: warning: stack frame size of 2656 bytes in function
I have reported this issue in the llvm bugzilla, but to make
it work with the clang-8 release, a small annotation is still
needed.
Link: https://bugs.llvm.org/show_bug.cgi?id=38809
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
Link: https://bugs.llvm.org/show_bug.cgi?id=40776
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ISC driver currently supports ITU-R 601 encoding which
utilizes the external hsync and vsync signals. ITU-R 656
format removes the need for these pins by embedding the
sync pulses within the data packet.
To support this feature, enable necessary register bits
when this feature is enabled via device tree.
Signed-off-by: Ken Sloat <ksloat@aampglobal.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The last user of this state has been converted, so we can now drop
this. Requeueing causes the queue to become unordered, which causes
problems with requests and (in the future) fences.
Since it is no longer needed, just get rid of this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cobalt driver is the only driver that uses VB2_BUF_STATE_REQUEUEING.
Replace it by VB2_BUF_STATE_ERROR so we can drop support for the
REQUEUEING state.
The requeueing state was used in the cobalt driver to optimize
buffer handling while waiting for a valid signal: by requeueing
buffers internally there was no need for userspace to handle and
requeue buffers with the ERROR flag set.
However, requeueing also makes the buffer handling unordered, which
is generally a bad idea. Requeueing also does not work with requests
and any future fence support.
Since it is really a minor optimization in the cobalt driver it is
best to just return the buffer in an ERROR state. With this change
support for requeueing can now be removed in vb2.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid call of dmaengine_terminate_all() between
dmaengine_prep_slave_single() and dmaengine_submit() by locking
the whole DMA submission sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Start streaming was sometimes failing because of pm_runtime_get_sync()
non-0 return value. In fact return value was not an error but a
positive value (1), indicating that PM was already enabled.
Fix this by going to error path only with negative return value.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function `sh_veu_find_fmt` returns an address that is an addition of a
base pointer `sh_veu_fmt` and an offset. The base pointer refers to a
global variable of which address cannot be NULL. Therefore, this commit
removes the NULL pointer checks on the return values of function
`sh_veu_find_fmt`.
Signed-off-by: Shaobo He <shaobo@cs.utah.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions, but omitted two occurrences that are accessed in the
mtk_v4l2_debug() macro. These only trigger compiler errors when DEBUG is
defined.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the SoC specific information for RZ/G2M(r8a774a1) SoC.
The VIN module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2M(r8a774a1) SoC.
The CSI-2 module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_ioremap_resource() already prints an error message on failure, so
there is no need to repeat that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changes to v4l2-fwnode in commit [1] triggered a lockdep warning in
rcar-vin. The first attempt to solve this warning in the rcar-vin driver
was incomplete and only pushed the warning to happen at stream on time
instead of at probe time.
This change reverts the incomplete fix and properly fixes the warning by
removing the need to hold the rcar-vin specific group lock when calling
v4l2_async_notifier_parse_fwnode_endpoints_by_port(). And instead takes
it in the callback where it's really needed.
[1] commit eae2aed1ea ("media: v4l2-fwnode: Switch to
v4l2_async_notifier_add_subdev")
Fixes: 6458afc8c4 ("media: rcar-vin: remove unneeded locking in async callbacks")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the new v4l2_subdev_internal_ops release op to free the
subdev memory only when the last user closed the file handle.
Move v4l2_device_unregister_subdev() to the end of the
vimc_ent_sd_unregister() function since now the unregister_subdev()
call may free the vimc_ent_device struct which is used after the
unregister_subdev() call. So this now has to be done last.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't free vimc_cap_device immediately, instead do this
in the video_device release function which is called when the
last user closes the video device. Only then is it safe to
free the memory.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The module ownership refcounting was done in media_entity_get/put,
but that was very confusing and it did not work either in case an
application had a v4l-subdevX device open and the module was
unbound. When the v4l-subdevX device was closed the media_entity_put
was never called and the module refcount was left one too high, making
it impossible to unload it.
Since v4l2-subdev.c was the only place where media_entity_get/put was
called, just move the functionality to v4l2-subdev.c and drop those
confusing entity functions.
Store the module in subdev_fh so module_put no longer depends on
the media_entity struct.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the subdevice created a device node, then the v4l2_subdev cannot
be freed until the last user of the device node closes it.
This means that we need a release() callback in v4l2_subdev_internal_ops
that is called from the video_device release function so the subdevice
driver can postpone freeing memory until the that callback is called.
If no video device node was created then the release callback can
be called immediately when the subdev is unregistered.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not possible to use devm_kzalloc since that memory is
freed immediately when the device instance is unbound.
Various objects like the video device may still be in use
since someone has the device node open, and when that is closed
it expects the memory to be around.
So use kzalloc and release it at the appropriate time.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vivid is unloaded it used vfree to free dev->bitmap_out,
but it was actually allocated using kmalloc. Use vzalloc
instead, conform what vivid-vid-cap.c does.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The media chardev kobject has no name, which made it hard to
debug when kobject debugging is turned on.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec chardev kobject has no name, which made it hard to
debug when kobject debugging is turned on.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend the vsp1_du_atomic_flush() API with writeback support by adding
format, pitch and memory addresses of the writeback framebuffer.
Writeback completion is reported through the existing frame completion
callback with a new VSP1_DU_STATUS_WRITEBACK status flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP1 driver will need to pass extra flags to the DU through the
frame completion API. Replace the completed bool flag by a bitmask to
support this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code that initializes the RPF format-related fields for display
pipelines will also be useful for the WPF to implement writeback
support. Split it from vsp1_du_atomic_update() to a new
vsp1_du_pipeline_set_rwpf_format() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the writeback feature of the WPF, to enable capturing
frames at the WPF output for display pipelines. To enable writeback the
vsp1_rwpf structure mem field must be set to the address of the
writeback buffer and the writeback field set to true before the WPF
.configure_stream() and .configure_partition() are called. The WPF will
enable writeback in the display list for a single frame, and writeback
will then be automatically disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Refactor the display list header setup to allow chained display lists
with display pipelines. Chain the display lists as for mem-to-mem
pipelines, but enable the frame end interrupt for every list as display
pipelines have a single list per frame.
This feature will be used to disable writeback exactly one frame after
enabling it by chaining a writeback disable display list.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WPF needs access to the current display list to configure writeback.
Add a display list pointer to the VSP1 entity .configure_stream()
operation.
Only display pipelines can make use of the display list there as
mem-to-mem pipelines don't have access to a display list at stream
configuration time. This is not an issue as writeback is only used for
display pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prepare for addition of more flags to the display list, replace the
'internal' flag field by a bitmask 'flags' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP-DL instances have two LIFs, and thus two copies of the
VI6_DISP_IRQ_ENB, VI6_DISP_IRQ_STA and VI6_WPF_WRBCK_CTRL registers. Fix
the corresponding macros accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Display list fragments have been renamed to bodies. Replace one last
occurrence of the word fragment in the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When configuring partitions for memory-to-memory pipelines, the WPF
accesses data of the current partition through pipe->partition.
Writeback support will require full configuration of the WPF while not
providing a valid pipe->partition. Rework the configuration code to fall
back to the full image width in that case, as is already done for the
part of the configuration currently relevant for display pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 3299ba5c0b ("[media] v4l: vsp1: Supply frames to
the DU continuously")
The DU output mode does not rely on frames being supplied on the WPF as
its pipeline is supplied from DRM. For the upcoming WPF writeback
functionality, we will choose to enable writeback mode if there is an
output buffer, or disable it (leaving the existing display pipeline
unharmed) otherwise.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- add debugfs support for dumping dma-debug information (Corentin Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
-----BEGIN PGP SIGNATURE-----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=nAMI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
- add debugfs support for dumping dma-debug information (Corentin
Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
Documentation/DMA-API-HOWTO: update dma_mask sections
sparc64/pci_sun4v: allow large DMA masks
sparc64/iommu: allow large DMA masks
sparc64: refactor the ali DMA quirk
ccio: allow large DMA masks
dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
dma-mapping: remove dma_mark_declared_memory_occupied
dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
dma-mapping: improve selection of dma_declare_coherent availability
dma-mapping: remove an incorrect __iommem annotation
of: select OF_RESERVED_MEM automatically
device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
mfd/sm501: depend on HAS_DMA
dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
dma-mapping: move debug configuration options to kernel/dma
dma-debug: add dumping facility via debugfs
dma: debug: no need to check return value of debugfs_create functions
videobuf2: replace a layering violation with dma_map_resource
dma-mapping: don't BUG when calling dma_map_resource on RAM
...
- Fix a unittest failure on UML. Preparation for converting to
kunit test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that
needs it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
-----BEGIN PGP SIGNATURE-----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=CnTd
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Fix a unittest failure on UML. Preparation for converting to kunit
test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that needs
it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
* tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: unittest: unflatten device tree on UML when testing
dt-bindings: Add vendor prefix for feiyang
dt-bindings: Add vendor prefix for techstar
dt-bindings: display: add missing semicolon in example
of: mark early_init_dt_alloc_reserved_memory_arch static
of: add dtc annotations functionality to dtx_diff
of: unittest: add caution to function header comment
of: unittest: remove report of expected error
dt-bindings: interrupt-controller: Convert ARM GICv3 to json-schema
dt-bindings: interrupt-controller: Convert ARM GIC to json-schema
dt-bindings: arm: l2x0: Convert L2 cache to json-schema
media: s5p-mfc: Fix memdev DMA configuration
dt-bindings: serial: sh-sci: Document r8a7778/9 HSCIF bindings
This has been a slightly more active cycle than normal with ongoing core
changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5 On-Demand-Paging MR
feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and fixing
the various unregistration race conditions in rxe's unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
* Drivers should not assume umem SGLs are in PAGE_SIZE chunks
* ucontext is accessed via udata not other means
* Start to make the core code responsible for object memory
allocation
* Drivers should convert struct device to struct ib_device
via a helper
* Drivers have more tools to avoid use after unregister problems
-----BEGIN PGP SIGNATURE-----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=p12E
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a slightly more active cycle than normal with ongoing
core changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5
On-Demand-Paging MR feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and
fixing the various unregistration race conditions in rxe's
unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
- drivers should not assume umem SGLs are in PAGE_SIZE chunks
- ucontext is accessed via udata not other means
- start to make the core code responsible for object memory
allocation
- drivers should convert struct device to struct ib_device via a
helper
- drivers have more tools to avoid use after unregister problems"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (280 commits)
net/mlx5: ODP support for XRC transport is not enabled by default in FW
IB/hfi1: Close race condition on user context disable and close
RDMA/umem: Revert broken 'off by one' fix
RDMA/umem: minor bug fix in error handling path
RDMA/hns: Use GFP_ATOMIC in hns_roce_v2_modify_qp
cxgb4: kfree mhp after the debug print
IB/rdmavt: Fix concurrency panics in QP post_send and modify to error
IB/rdmavt: Fix loopback send with invalidate ordering
IB/iser: Fix dma_nents type definition
IB/mlx5: Set correct write permissions for implicit ODP MR
bnxt_re: Clean cq for kernel consumers only
RDMA/uverbs: Don't do double free of allocated PD
RDMA: Handle ucontext allocations by IB/core
RDMA/core: Fix a WARN() message
bnxt_re: fix the regression due to changes in alloc_pbl
IB/mlx4: Increase the timeout for CM cache
IB/core: Abort page fault handler silently during owning process exit
IB/mlx5: Validate correct PD before prefetch MR
IB/mlx5: Protect against prefetch of invalid MR
RDMA/uverbs: Store PR pointer before it is overwritten
...
-----BEGIN PGP SIGNATURE-----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=tD1x
-----END PGP SIGNATURE-----
Merge tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove sensor drivers that got converted from soc_camera
- remaining soc_camera drivers got moved to staging
- some documentation cleanups and improvements
- the imx staging driver now supports imx7
- the ov9640, mt9m001 and mt9m111 got converted from soc_camera
- the vim2m driver now does what a m2m convert driver expects to do
- epoll() fixes on media subsystems
- several drivers fixes, typos, cleanups and improvements
* tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (346 commits)
media: dvb/earth-pt1: fix wrong initialization for demod blocks
media: vim2m: Address some coding style issues
media: vim2m: don't use BUG()
media: vim2m: speedup passthrough copy
media: vim2m: add an horizontal scaler
media: vim2m: don't accept YUYV anymore as output format
media: vim2m: add vertical linear scaler
media: vim2m: better handle cap/out buffers with different sizes
media: vim2m: use different framesizes for bayer formats
media: vim2m: add support for VIDIOC_ENUM_FRAMESIZES
media: vim2m: ensure that width is multiple of two
media: vim2m: improve debug messages
media: vim2m: add bayer capture formats
media: a few more typos at staging, pci, platform, radio and usb
media: Documentation: fix several typos
media: staging: fix several typos
media: include: fix several typos
media: common: fix several typos
media: v4l2-core: fix several typos
media: usb: fix several typos
...
earth-pt1 driver was decomposed/restructured by the commit b732539efd
("media: dvb: earth-pt1: decompose pt1 driver into sub drivers"),
but it introduced a problem regarding concurrent streaming:
Opening a new terrestial stream stops the reception of an existing,
already-opened satellite stream.
The demod IC in earth-pt1 boards contains 2 pairs of terr. and sat. blocks,
supporting 4 concurrent demodulations, and the above problem was because
the config of a terr. block contained whole reset/init of the pair blocks,
thus each open() of a terrestrial frontend wrongly cleared the config of
its peer satellite block of the demod.
This whole/pair reset should be executed earlier and not on each open().
Fixes: b732539efd ("media: dvb: earth-pt1: decompose pt1 driver into sub drivers")
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we did lots of change at vim2m driver, let's take the
opportunity and make checkpatch happier, addressing the
errors/warnings that makes sense.
While here, increment driver's version.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There's no reason why this driver should use BUG(). Instead,
just properly handle issue, returning an error code where
pertinent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When in passthrough mode, copy the entire line at once, in
order to make it faster (if not HFLIP).
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
