Add more information in calibration error log to differentiate
single-ended and differential calibration.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20221115103124.70074-3-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add smart calibration support for STM32MP1.
- STM32MP15x: both linear & offset calibration are supported
- STM32MP13x: Only offset calibration is supported
Linear calibration:
Linear calibration is SoC dependent and does not change over time
so it can be done only once.
Linear calibration may have already been done in u-boot.
Skip calibration execution if calibration data are already available.
Save calibration factors in private data and restore them from private
data on next ADC start.
Offset calibration:
This calibration may vary over time, depending on temperature or voltage.
Run offset single-ended and differential calibration on each ADC start,
as it is not time consuming. This calibration do not need to be saved.
So, remove calfact_s and calfact_d value and bitfields that are no
longer used.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20221115103124.70074-2-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a board where the reset pin of the ad74412 is connected to a
gpio, but also pulled low (i.e., asserted) by default. Hence to get
the chip out of reset, the driver needs to know about that gpio and
deassert the reset signal before attempting to communicate with the
chip.
When a reset-gpio is given in device tree, use that instead of the
software reset. According to the data sheet, the two methods are
functionally equivalent.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20221115095517.1008632-4-linux@rasmusvillemoes.dk
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad74412 and ad74413 devices have an active-low reset pin. Add a
binding allowing one to specify a gpio tied to that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221115095517.1008632-3-linux@rasmusvillemoes.dk
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As in other bindings, let's use specific compatibles together with the
fallback compatible. Adjust the bindings for it.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221031182456.952648-1-luca@z3ntu.xyz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD74115H is a single-channel, software-configurable, input and
output device for industrial control applications. The AD74115H
provides a wide range of use cases, integrated on a single chip.
These use cases include analog output, analog input, digital output,
digital input, resistance temperature detector (RTD), and thermocouple
measurement capability. The AD74115H also has an integrated HART modem.
A serial peripheral interface (SPI) is used to handle all communications
to the device, including communications with the HART modem. The digital
input and digital outputs can be accessed via the SPI or the
general-purpose input and output (GPIO) pins to support higher
speed data rates.
The device features a 16-bit, sigma-delta analog-to-digital converter
(ADC) and a 14-bit digital-to-analog converter (DAC).
The AD74115H contains a high accuracy 2.5 V on-chip reference that can
be used as the DAC and ADC reference.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221117080916.411766-3-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD74115H is a single-channel, software-configurable, input and
output device for industrial control applications. The AD74115H
provides a wide range of use cases, integrated on a single chip.
These use cases include analog output, analog input, digital output,
digital input, resistance temperature detector (RTD), and thermocouple
measurement capability. The AD74115H also has an integrated HART modem.
A serial peripheral interface (SPI) is used to handle all communications
to the device, including communications with the HART modem. The digital
input and digital outputs can be accessed via the SPI or the
general-purpose input and output (GPIO) pins to support higher
speed data rates.
The device features a 16-bit, sigma-delta analog-to-digital converter
(ADC) and a 14-bit digital-to-analog converter (DAC).
The AD74115H contains a high accuracy 2.5 V on-chip reference that can
be used as the DAC and ADC reference.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221117080916.411766-2-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The constant AD74413R_ADC_RESULT_MAX is defined via GENMASK, so its
type is "unsigned long".
Hence in the expression voltage_offset * AD74413R_ADC_RESULT_MAX,
voltage_offset is first promoted to unsigned long, and since it may be
negative, that results in a garbage value. For example, when range is
AD74413R_ADC_RANGE_5V_BI_DIR, voltage_offset is -2500 and
voltage_range is 5000, so the RHS of this assignment is, depending on
sizeof(long), either 826225UL or 3689348814709142UL, which after
truncation to int then results in either 826225 or 1972216214 being
the output from in_currentX_offset.
Casting to int avoids that promotion and results in the correct -32767
output.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Fixes: fea251b6a5 (iio: addac: add AD74413R driver)
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221118123209.1658420-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/202211220935338446115@zte.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove adis_initial_startup function since it is not used
anymore.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-10-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16240_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-9-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16203_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-8-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16400_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-7-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16260_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-6-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16136_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-5-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16209_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-4-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Call '__adis_initial_startup()' instead of its locked variant in
'adis16201_probe()'.
The locks are not needed at this point.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-3-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add '__adis_enable_irq()' implementation which is the unlocked
version of 'adis_enable_irq()'.
Call '__adis_enable_irq()' instead of 'adis_enable_irq()' from
'__adis_intial_startup()' to keep the expected unlocked functionality.
This fix is needed to remove a deadlock for all devices which are
using 'adis_initial_startup()'. The deadlock occurs because the
same mutex is acquired twice, without releasing it.
The mutex is acquired once inside 'adis_initial_startup()', before
calling '__adis_initial_startup()', and once inside
'adis_enable_irq()', which is called by '__adis_initial_startup()'.
The deadlock is removed by calling '__adis_enable_irq()', instead of
'adis_enable_irq()' from within '__adis_initial_startup()'.
Fixes: b600bd7eb3 ("iio: adis: do not disabe IRQs in 'adis_init()'")
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
VREFP bit was missing from channel configuration mask and VREFN bit was
included twice instead which fails to enable positive reference buffer when
requested by a channel. Channels that don't enable vrefp buffer were not
affected.
Fixes: a44ef7c460 ("iio: adc: add max11410 adc driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Link: https://lore.kernel.org/r/20221122114718.17557-1-Ibrahim.Tilki@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- The ad7927 is fully compatible with ad7928 driver, add
documentation for device.
- ad7923 and ad7924 are treated the same in the driver, show
the relationship in the documentation.
Suggested-by: Lukasz Zemla <Lukasz.Zemla@woodward.com>
Signed-off-by: Edmund Berenson <edmund.berenson@emlix.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221122161437.18937-1-edmund.berenson@emlix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-569-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-568-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-567-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-191-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-190-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-189-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-188-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-187-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Crt Mori<cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-186-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-185-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-184-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-183-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-182-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-181-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-180-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-179-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-178-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-177-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-176-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-175-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-174-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-173-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20221118224540.619276-172-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-171-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-170-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
