This has two reasons: a) to clearly mark that drivers don't have any
business using it, and b) because we're going to use it for the
(dangerous) global rkey soon, so that drivers don't create on themselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is meant to add support of ACPI to the Hisilicon RoCE
driver.
Changes done are primarily meant to detect the type and then either
use DT specific or ACPI spcific functions. Where ever possible,
this patch tries to make use of Unified Device Property Interface
APIs to support both DT and ACPI through single interface.
This patch depends upon HNS ethernet driver to Reset RoCE. This
function within HNS ethernet driver has also been enhanced to
support ACPI and is part of other accompanying patch with this
patch-set.
NOTE: The changes in this patch are done over below branch,
https://github.com/dledford/linux/tree/hns-roce
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the Hip06 SoC, the RoCE Engine is part of the Hisilicon Network
Subsystem and is dependent upon DSAF module. Therefore, certain
functions like RESET are exposed through the common registers of
HNS DSAF module which are memory-mapped by the HNS driver and
currently can only be accessed through DT/syscon interface.
This patch adds the support of ACPI to the existing RoCE reset
function in the HNS driver(please refer NOTE 2). Hisilicon RoCE
driver (please refer NOTE 1) shall call this reset function during
probe time to reset the RoCE Engine.
The HNS Reset function indirectly ends up in calling the _DSM()
function part of the DSDT ACPI Table. Actual reset functionality
for ACPI is implemented within the ACPI DSDT Table which also has
been enhanced to support this change.
Support of ACPI in the HNS RoCE driver shall be pushed through a
different accompanying below patch:
"IB/hns: Add support of ACPI to the Hisilicon RoCE Driver"
NOTE 1: HNS RoCE driver has already been accepted by its maintainer
Doug Ledford<dledford@redhat.com>. Please refer below link:
https://www.spinics.net/lists/linux-rdma/msg38850.html
NOTE 2: RoCE reset function patch has been accepted and now is
part of the net-next:
https://www.mail-archive.com/netdev@vger.kernel.org/msg123867.html
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXu20hAAoJEORje4g2cliniO8P/0nMxLemOxY63u7P6DqT+UZQ
+LN62W+/iLicNayKkt8mtcjnDm768YcF3ADvx73vRvKEeUyyEqT5ChMA59eicf70
rrumfNXB/kfBOaPh5rFWf4Tn8WWpKW+0559drm80NslFZF9jjF9pwv5QGg7xISb7
fYLcDQWn+5fYDuZzYsSu8zZKUEyGN0AugdjfxT5OHfh4rw+6oqGDb2fhH6LdkD8q
j3Qx1cPmdQQnjJ5veXJFJT5qHFDqJlNmy85s4l99ItdWD/bcU29ue3Q3vNf7+lHp
XoJB4ZRWG7sf98yXYXnOUt3iGUMdSJzpLfZqh/Nx9U1LZpdJ8lmBf7pRuR1hpPIN
yDitcz+CMcFVr2WxvwWaUPhRE7SJsZxxr6tQISgRicYcFVyy9e7mLjABMtkh9vEn
CXXqiDGUb/27HqTi9ha5qRiLoeT8yFpOCkINL4omV2FJKoUEbC+Jbq5P0mjnPpS1
ZdzTOzWCtkDQGtLbi+nCIF5SVTv7CCDU+6VpGZPmk6M4/ednwajhxGPsbw6bRpna
ck5SglGO8dFAaUv1UVRq04PIt7Lj2FRakP7sHWx3tc9XEP8syLX0OEiVB+ZN3yRn
y2TlpsREk7AqDdRulwM4qfuNd4AxaDklXyS3C79RiJtenYO4GUGrJ6J6ryesLg8u
tGKVV3fXEr2Hve6cTkpu
=+m21
-----END PGP SIGNATURE-----
Merge tag 'shared-for-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma into mlx5-shared
Mellanox ConnectX-4/Connect-IB shared code (SW part)
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch added maintainers for RoCE driver.
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch added Kconfig and Makefile for building RoCE module.
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These are the various new source code files for the Hisilicon
RoCE driver for ARM architecture.
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch added DTS binding document for Hisilicon RoCE driver.
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use PPP_ALLSTATIONS, PPP_UI, and SEND_SHUTDOWN instead of 0xff,
0x03, and 2 separately.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-20
This series contains updates to ixgbe and ixgbevf.
Veola fixes how the backplane reports the media in ethtool, as KR, KX or
KX4 based on the backplane interface present.
Emil fixes ixgbevf since an incorrect size parameter for
ixgbevf_write_msg_read_ack() ended up only giving the PF the first 4
bytes of the MAC address, so correct the size by calculating it on the
fly for all instances where we call ixgbevf_write_msg_read_ack(). Added
geneve receive offload support for x550em_a.
Don fixes the LED interface for x557 since it uses a different interface.
Added support for the new x557 copper device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new copper device X557.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X557 devices use a different interface to the LED for the port.
This patch reflect that change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add geneve Rx offload support for x550em_a.
The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.
Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().
Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().
Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Markus Elfring says:
====================
tun: Fine-tuning for update_filter()
A few update suggestions were taken into account
from static source code analysis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust a jump target according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-08-19
This series contains updates to i40e and i40evf only.
Jake provides several patches, first just moves a function to co-locate
the two functions related to configuring RSS via the admin queue, which
should help in spotting bugs when comparing the two functions. Fixed
an issue where commit e69ff813af ("i40e: rework the functions to
configure RSS with similar parameters") missed checking whether the seed
is NULL before using it and did not use the passed in *lut parameter.
Fixed an issue where a previous refactor missed i40e_vsi_config_rss()
and the values were being ignored, so checked for the fields and used
them instead of default values. Lastly replaced calls to
create_singlethread_workqueue() with alloc_workqueue() to provide more
control over workqueue creation and allows explicit setting of the
desired mode of operation.
Mitch adds link speed to log messages and reports speed through ethtool.
Carolyn refactors tail bump check and fixes byte ordering problems found
when enabling this feature support. Adds support for HMC resources and
profile commands for x722 firmware.
Heinrich Schuchardt fixes format identifiers from %u to %d since the
variable is defined as an integer.
Catherine fixes an issue where there was a race condition between the
completion of the client open and calls to the client ops, so ensured
that client ops are not called until we are sure client is open.
Harshitha makes sure that i40e_client_release() does not try to use
an adapter pointer which may not be initialized, so make sure it is.
Joe Perches fixes the use of the local macro XSTRINGIFY() to use
__stringify() instead.
Avinash corrects the mutex usage in client_subtask(). Fixed the RDMA
client to open again after reset since it is closed during a PF reset.
Jeff (me) clean up whitespace issues, where indentation was done
inconsistently and with spaces versus tabs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch creates sample code exercising bpf_skb_{set,get}_tunnel_key,
and bpf_skb_{set,get}_tunnel_opt for GRE, VXLAN, and GENEVE. A native
tunnel device is created in a namespace to interact with a lwtunnel
device out of the namespace, with metadata enabled. The bpf_skb_set_*
program is attached to tc egress and bpf_skb_get_* is attached to egress
qdisc. A ping between two tunnels is used to verify correctness and
the result of bpf_skb_get_* printed by bpf_trace_printk.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code uses busy retry when unable to send out receive
completions due to full ring buffer. It also gives up retrying after limit
is reached, and causes receive buffer slots not being recycled.
This patch implements batching of receive completions. It also prevents
dropping receive completions due to full ring buffer.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDMA client is closed during the PF reset and needs to be opened again.
Setting the flag so that RDMA client is opened in watchdog() function.
Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.
Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.
This is a patch suggested by RDMA team.
Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __stringify instead.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.
Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were having a race between the completion of the client open and
calls to the client ops so don't call a client op unless we are sure the
client is open.
Testing Hints: Load IWARP driver and make sure it works as expected.
Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for HMC resource and profile cmds for X722
firmware.
Change-ID: Icc332101f38ab15d1bfa167823100eb4f6822f7e
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes byte ordering problems found when enabling this feature
support. Without this patch, the feature will not work correctly. This
patch fixes the definitions to have the correct byte order.
Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver tells us the link speed, so do something with that
information. Add link speed to log messages, and report speed through
ethtool.
Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".
Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've already set sk to sock->sk and dereferenced it, so if it's NULL
we would have crashed already. Moreover, if it was NULL we would have
crashed anyway when jumping to 'out' and trying to unlock the sock.
Furthermore, if we had assigned a different value to 'sk' we would
have been calling lock_sock() and release_sock() on different sockets.
My conclusion is that these two lines are complete nonsense and only
serve to confuse the reader.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-18
This series contains updates to ixgbe and ixgbevf.
Emil cleans up confusing amongst the users by making an error message
into a debug message, since the TXDCTL.ENABLE (and comparable
VFTXDCTL.ENABLE for ixgbevf) bit is set only when the
transmit queue is actually enabled, which may not happen during the
configure phase eve if we waited for it. Converts to using netdev_dbg()
macro instead of our home brewed macro for ixgbevf. Converted the
service task to use atomic bitwise operations when setting and checking
reset requests to reduce the possibility of race conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Platform conversion
This patch series converts the bcm_sf2 driver from a traditional DSA driver
into a platform_device driver and makes it use the new DSA binding that Andrew
introduced in the latest merge window.
Prior attempts used to coerce the code in net/dsa/dsa2.c to accept the old
binding, while really there is only one broken single user out there: bcm_sf2,
so instead, just assume the new DT binding is deployed and use it accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
