There are a few bugs in this code. 1) No checks for whether
dma_alloc_attrs() or __get_free_pages() failed. 2) If
video_register_device() fails it doesn't clean up the dma attrs or the
free pages. 3) The video_device_release() function frees "vfd" which
leads to a use after free on the next line. The call to
video_unregister_device() is not required so I have just removed that.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
stm32_cec_probe() did not unprepare clocks on error handling paths. The
patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae545 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Initializing the dma addresses of the capture buffers can
move to the 'buf_init' callback, since it is enough to do
it once for each buffer and not every time it is queued.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The virtual address can be accessed using vb2_plane_vaddr
therefore there is no need to save it in an extra field in
'rkisp1_buffer'. Remove it.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In go7007_alloc() kzalloc() is used for struct go7007
allocation. It means that there is no need in zeroing
any members, because kzalloc will take care of it.
Removing these reduntant initialization steps increases
execution speed a lot:
Before:
+ 86.802 us | go7007_alloc();
After:
+ 29.595 us | go7007_alloc();
Fixes: 866b8695d6 ("Staging: add the go7007 video driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Captured video would be out of sync when using the adv7280 with
the BT.656-4 protocol. Certain registers (0x04, 0x31, 0xE6) had to
be configured properly to ensure BT.656-4 compatibility.
An error in the adv7280 reference manual suggested that EAV/SAV mode
was enabled by default, however upon inspecting register 0x31, it was
determined to be disabled by default.
[fabio: Introduce "adv,force-bt656-4" to not affect the existing users]
[hverkuil: fix a small checkpatch alignment warning]
Signed-off-by: Matthew Michilot <matthew.michilot@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a reset input that can be controlled by GPIO. Let's add it
to let the driver control it if required.
[hverkuil: fix a small checkpatch alignment warning]
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error
message, and then continues to set DVB_USB_STATE_I2C. This affects the
logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap
even if the i2c_add_adapter fails.
Fix this by returning at the failure of i2c_add_adapter and then move
dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init.
Fixes: 13a79f14ab ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If vp702x_usb_in_op fails, the mac address is not initialized.
And vp702x_read_mac_addr does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of vp702x_usb_in_op.
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If dibusb_read_eeprom_byte fails, the mac address is not initialized.
And nova_t_read_mac_address does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of dibusb_read_eeprom_byte.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The s_learning_mode() function is called in response to the ioctl
LIRC_SET_WIDEBAND_RECEIVER, so rename it to s_wideband_receiver().
Learning mode is when both the wideband receiver is turned on and
carrier reports are enabled.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Any timeout larger than LIRC_VALUE_MASK cannot work for the lirc uapi.
LIRC_VALUE_MASK is about 16 seconds which is more than enough.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When carrier reports are enabled, send them over loopback.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The LIRC_SET_TRANSMITTER_MASK ioctl should return the number of emitters
if an invalid list was set.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:
arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).
Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().
This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Fixes: dae52d009f ("V4L/DVB: ngene: Initial check-in")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/linux-hardening/20210420001631.GA45456@embeddedor/
Currently it's possible to iterate over the dangling pointer in case the device
suddenly disappears. This may happen becase callers put it at the end of a loop.
Instead, let's move that call inside acpi_dev_get_next_match_dev().
Fixes: 803abec64e ("media: ipu3-cio2: Add cio2-bridge to ipu3-cio2 driver")
Fixes: bf263f64e8 ("media: ACPI / bus: Add acpi_dev_get_next_match_dev() and helper macro")
Fixes: edbd1bc495 ("efi/dev-path-parser: Switch to use for_each_acpi_dev_match()")
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Logilink VG0022A DVB-T2 stick has these three devices. So to enable
support for this stick in the presence of MEDIA_SUBDRV_AUTOSELECT,
let DVB_USB_AF9035 select the two other drivers.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a sub device doesn't immediately bind after it was added, emit an
error indication to the kernel log to help debugging. This happens for
example if the needed driver isn't available at all.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
break is not useful after a goto, so delete 'break' after 'goto'.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
Fixes: cb496cd472 ("media: cxd2880-spi: Add optional vcc regulator")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
deleted the repeated word 'the' in the comments.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for capturing embedded data from the sensor. The only
difference with capturing pixel data and embedded data is that we need
to ensure the PIX PROC is disabled for embedded data so that CAL doesn't
repack the data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL RX has a single sink and a single source pad. To support multiple
streams, we will have multiple source pads (up to 8, one for each
CAL context).
Change the driver to allow creating more source pads and change the code
accordingly to handle multiple source pads. We still keep
CAL_CAMERARX_NUM_SOURCE_PADS as 1, and the behavior is unchanged.
Also rename CAL_CAMERARX_PAD_SOURCE to CAL_CAMERARX_PAD_FIRST_SOURCE to
highlight that it's the first source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The following patches add multistream support and we will have multiple
video devices using the same camerarx instances. Thus we need
enable/disable refcounting for the camerarx.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We don't have any locking in camerarx for the subdev ops. We have
managed fine so far without locking, but in the future multiple video
capture devices can use the same camerarx, and locking is a must.
Add a mutex to protect the camerarx subdev ops. Some of the functions
were slightly restructured to make lock handling cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When starting streaming the driver currently programs the buffer
address to the CAL base-address register and assigns the buffer pointer
to ctx->dma.pending. This is not correct, as the buffer is not
"pending", but active, and causes the first buffer to be needlessly
written twice.
Fix this by assigning the buffer pointer to ctx->dma.active.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Somewhere along the way the context uninitialization has gone a bit odd:
* We have cal_ctx_create() but no matching destroy call, but we still
need to call cal_ctx_v4l2_cleanup() for each context.
* We have cal_media_cleanup() which calls cal_ctx_v4l2_cleanup() for all
contexts, but cal_media_init() is not where the contexts are created.
* The order of uninit steps in cal_remove() is different than the error
handling path in cal_probe().
* cal_probe()'s error handling calls cal_ctx_v4l2_cleanup() for each
context, but also calls cal_media_clean(), doing the same context
cleanup twice.
So fix these, by introducing cal_ctx_destroy(), and using that in
appropriate places instead of calling cal_ctx_v4l2_cleanup() in
cal_media_clean(). Also use normal kzalloc (and kfree) instead of devm
version as we anyway do manual cleanup for each context.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most of the driver has moved from ARRAY_SIZE(cal->phy) to
cal->data->num_csi2_phy, but we have one place left in cal_remove. Also,
checking for cal->phy[i] != NULL is not needed as we always have all the
phys instantiated.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current driver only ever needs 2 DMA contexts (one per PHY), but we
need to use more of the 8 contexts to add support for multiple streams.
Change the code so that we allocate DMA contexts as needed, which at
this time is 1 per PHY, but could be up to 8.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
struct cal_camerarx has fmtinfo field which is used to point to the
current active input format. The only place where the field is used is
cal_camerarx_get_ext_link_freq().
With multiple streams the whole concept of single input format is not
valid anymore, so lets remove the field by looking up the format in
cal_camerarx_get_ext_link_freq(), making it easier to handle the
multistream-case in the following patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL driver enumerates mbus codes in the connected subdev to create a
list of supported formats reported to userspace, and initializes
ctx->v_fmt and ctx->fmtinfo to one of those formats.
This works fine for legacy mode, but is not correct for MC mode, and the
list is not even used in MC mode.
Fix this by adding a new function, cal_ctx_v4l2_init_mc_format, which
only initializes ctx->v_fmt and ctx->fmtinfo to a default value.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To make it more obvious if the function in question is dealing with
media-controller API or the legacy API, rename legacy API functions to
cal_legacy_*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit e5b6b07a1b ("media: v4l2: Extend VIDIOC_ENUM_FMT to support
MC-centric devices") added support to enumerate formats based on
mbus-code.
Add this feature to cal driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix a typo in a comment in cal_camerarx_sd_set_fmt().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
cal_camerarx_sd_set_fmt() accepts any value for the format field, but
there should be no reason to have any other value accepted than
V4L2_FIELD_NONE. So set the field always to V4L2_FIELD_NONE.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
cal_async_notifier_complete() doesn't handle errors returned from
cal_ctx_v4l2_register(). Add the error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for supporting multiple virtual channels and datatypes,
add vc and datatype fields to cal_ctx, initialize them to the currently
used values, and use those fields when writing to the register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I have not noticed any errors due to this, but the DMA configuration
looks racy. Setting the DMA mode bitfield in CAL_WR_DMA_CTRL supposedly
enables the DMA. However, the driver currently a) continues configuring
the DMA after setting the mode, and b) enables the DMA interrupts only
after setting the mode.
This probably doesn't cause any issues as there should be no data coming
in to the DMA yet, but it's still better to fix this.
Add a new function, cal_ctx_wr_dma_enable(), to set the DMA mode field,
and call that function only after the DMA config and the irq enabling
has been done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We already have functions to reserve and release a pix proc unit, but we
always reserve such and the code expects the pix proc unit to be used.
Add a new field, 'use_pix_proc', to indicate if the pix prox unit has
been reserved and should be used. Use the flag to skip programming pix
proc unit when not needed.
Note that we still always set the use_pix_proc flag to true.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL has 4 pixel processing units but the units are not needed e.g. for
metadata. As we could be capturing 4 pixel streams and 4 metadata
streams, i.e. using 8 DMA contexts, we cannot assign a pixel processing
unit to every DMA context. Instead we need to reserve a pixel processing
unit only when needed.
Add functions to reserve and release a pix proc unit, and use them in
cal_ctx_prepare/unprepare. Note that for the time being we still always
reserve a pix proc unit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Disable CSI2 context and pix proc in cal_ctx_stop() to ensure they are
not used if the same context is used later on a different PHY or without
pix proc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Asserting ComplexIO reset seems to affect the HW (ie. asserting reset
will break an active capture), but the RESET_DONE bit never changes to
"reset is ongoing" state. Thus we always get a timeout.
Drop the wait, as it seems to achieve nothing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL driver currently ignores VC related errors. To help catch error
conditions, enable all the VC error interrupts and handle them in the
interrupt handler by printing an error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The macros related to CAL_CSI2_VC_IRQ can be handled better by having
the VC number as a macro parameter.
Note that the macros are not used anywhere yet, so no other changes are
needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL_HL_IRQ_MASK macro is used for both WDMA start and end status bits.
For clarity, rename CAL_HL_IRQ_MASK macro to CAL_HL_IRQ_WDMA_END_MASK
and CAL_HL_IRQ_WDMA_START_MASK.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename cal_ctx->index to dma_ctx to clarify that the field refers to the
DMA context number.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL has 4 pixel processing contexts (PIX PROC) of which the driver
currently uses pix proc 0 for PHY0, and pix proc 1 for PHY1 (as the
driver supports only a single source per PHY).
Add a pix_proc field to cal_ctx to allow us to use different pix proc
contexts in the future
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL has 8 CSI2 contexts per PHY, which are used to tag the incoming
data. The current driver only uses the first context, but we need to
support all of them to implement multi-stream support.
Add a csi2_ctx field to cal_ctx, which indicates which of the 8 CSI2
contexts is used for the particular cal_ctx. Also clean up the context
register macros to take the CSI2 context number as a parameter.
Note that before this patch the CSI2 context used for both PHYs was
always 0. This patch always uses cal_ctx index number as the CSI2
context. There is no functional difference, but this approach will work
also in the future when we use more than 1 CSI2 context per PHY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
cal_ctx's index and cport fields are numbers less than 8. In the
following patches we will get a bunch of new fields, all of which are
similar small numbers, so lets change the type to u8.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the following patches we need to do context configuration which might
fail. Add new functions, cal_ctx_prepare and cal_ctx_unprepare, to
handle such configuration.
[hverkuil: fix spurious newline checkpatch warning]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL driver uses V4L2_CID_PIXEL_RATE to get the required pixel rate, and
then changes that value to link rate before configuring the registers.
Rewrite the code to use v4l2_get_link_freq(), which simplifies the code
as we get the link rate directly, and it also adds support for
V4L2_CID_LINK_FREQ.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For some reason CAL_CTRL is written at the end of cal_ctx_wr_dma_config.
CAL_CTRL is a global (for CAL) register, so it should be independent of
contexts.
Move the code to cal_runtime_resume().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL driver uses "sensor" name to refer to the subdev connected to CAL.
As the subdev can also be a bridge, the naming is misleading and might
cause the reader to think it refers to the actual sensor at the end of
the pipeline.
Rename "sensor" to "source".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
cal_camerarx->dev field is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2-compliance complains about g/s_parm when using the non-MC API. Fix
it by adding the functions and just call v4l2_s/g_parm_cap for the
phy subdev.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The continue statement at the end of a for-loop has no effect,
remove it.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Convert list_for_each() to list_for_each_entry() where
applicable.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The max number of allowed logical addresses was set to 1 in
vivid, for no good reason. This prevented testing with multiple
logical addresses for the same CEC device. Increase this number to
CEC_MAX_LOG_ADDRS.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
deleted the repeated word 'the' in the comments.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SAMA5D2 does not have the YCYC field for the RLP (rounding, limiting,
packaging) module.
The YCYC field is supposed to work with interleaved YUV formats like YUYV.
In SAMA5D2, we have to use YYCC field, which is used for both planar
formats like YUV420 and interleaved formats like YUYV.
Fix the according rlp callback to replace the generic YCYC field (which
makes more sense from a logical point of view) with the required YYCC
field.
Fixes: debfa49687 ("media: atmel: atmel-isc-base: add support for more formats and additional pipeline modules")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/pci/ivtv/ivtv-i2c.c:245 ivtv_i2c_register() error: buffer overflow 'hw_devicenames' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:266 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:269 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:275 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:280 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:290 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
The logic at ivtv_i2c_register() could let buffer overflows at
hw_devicenames and hw_addrs arrays.
This won't happen in practice due to a carefully-contructed
logic, but it is not error-prune.
Change the logic in a way that will make clearer that the
I2C hardware flags will affect the size of those two
arrays, and add an explicit check to avoid buffer overflows.
While here, use the bit macro.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
So, use a kmalloc'ed buffer.
Cc: stable@vger.kernel.org # Kernel 4.9 and upper
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The logic at delta_ipc_open() tries to copy past the size of
the name passed to it:
drivers/media/platform/sti/delta/delta-ipc.c:178 delta_ipc_open() error: __memcpy() 'name' too small (17 vs 32)
Basically,this function is called just one with:
ret = delta_ipc_open(pctx, "JPEG_DECODER_HW0", ...);
The string used there has just 17 bytes. Yet, the logic tries
to copy the entire name size (32 bytes), which is plain wrong.
Replace it by strscpy, which is good enough to copy the string,
warranting that this will be NUL-terminated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The logic at dib8000_get_init_prbs() has a few issues:
1. the tables used there has an extra unused value at the beginning;
2. the dprintk() message doesn't write the right value when
transmission mode is not 8K;
3. the array overflow validation is done by the callers.
Rewrite the code to fix such issues.
This should also shut up those smatch warnings:
drivers/media/dvb-frontends/dib8000.c:2125 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2129 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_2k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2131 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_4k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2134 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the "default m", as options should default to disabled.
No other media driver is enabled by default.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add Geniatech MyGica T230C2_LITE and T230A as many people
are asking support for these devices on forums.
Link: https://lore.kernel.org/linux-media/YMuptIYFLdwSmw//@kali
Signed-off-by: Ján Čáni <pego149@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener
to another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance
(for pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require
jump labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast address
allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks
in NAPI context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and NXP
(our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm 60GHz WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LvtX
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
Merge misc updates from Andrew Morton:
"191 patches.
Subsystems affected by this patch series: kthread, ia64, scripts,
ntfs, squashfs, ocfs2, kernel/watchdog, and mm (gup, pagealloc, slab,
slub, kmemleak, dax, debug, pagecache, gup, swap, memcg, pagemap,
mprotect, bootmem, dma, tracing, vmalloc, kasan, initialization,
pagealloc, and memory-failure)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (191 commits)
mm,hwpoison: make get_hwpoison_page() call get_any_page()
mm,hwpoison: send SIGBUS with error virutal address
mm/page_alloc: split pcp->high across all online CPUs for cpuless nodes
mm/page_alloc: allow high-order pages to be stored on the per-cpu lists
mm: replace CONFIG_FLAT_NODE_MEM_MAP with CONFIG_FLATMEM
mm: replace CONFIG_NEED_MULTIPLE_NODES with CONFIG_NUMA
docs: remove description of DISCONTIGMEM
arch, mm: remove stale mentions of DISCONIGMEM
mm: remove CONFIG_DISCONTIGMEM
m68k: remove support for DISCONTIGMEM
arc: remove support for DISCONTIGMEM
arc: update comment about HIGHMEM implementation
alpha: remove DISCONTIGMEM and NUMA
mm/page_alloc: move free_the_page
mm/page_alloc: fix counting of managed_pages
mm/page_alloc: improve memmap_pages dbg msg
mm: drop SECTION_SHIFT in code comments
mm/page_alloc: introduce vm.percpu_pagelist_high_fraction
mm/page_alloc: limit the number of pages on PCP lists when reclaim is active
mm/page_alloc: scale the number of pages that are batch freed
...
vma_lookup() finds the vma of a specific address with a cleaner interface
and is more readable.
Link: https://lkml.kernel.org/r/20210521174745.2219620-15-Liam.Howlett@Oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hi Linus,
Please, pull the following patch that fixes an out-of-bounds
warning in the media subsystem. This is part of the ongoing
efforts to globally enable -Warray-bounds.
Thanks!
-----BEGIN PGP SIGNATURE-----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=PfCd
-----END PGP SIGNATURE-----
Merge tag 'array-bounds-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull array-bounds fixes from Gustavo Silva:
"Fix an out-of-bounds warning in the media subsystem.
This is part of the ongoing efforts to globally enable -Warray-bounds"
* tag 'array-bounds-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
media: siano: Fix out-of-bounds warnings in smscore_load_firmware_family2()
v4l2_ctrl_new_std() fails if the caller provides no 'step' parameter for
integer control, so define it to fix following error:
s5p_mfc_dec_ctrls_setup:1166: Adding control (1) failed
Fixes: c3042bff91 ("media: s5p-mfc: Use display delay and display enable std controls")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the vpu is not running, we should not rely on VPU_IDLE_REG
value. In this case, the suspend cb should only unprepare the
clock. This fixes a system-wide suspend to ram failure:
[ 273.073363] PM: suspend entry (deep)
[ 273.410502] mtk-msdc 11230000.mmc: phase: [map:ffffffff] [maxlen:32] [final:10]
[ 273.455926] Filesystems sync: 0.378 seconds
[ 273.589707] Freezing user space processes ... (elapsed 0.003 seconds) done.
[ 273.600104] OOM killer disabled.
[ 273.603409] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 273.613361] mwifiex_sdio mmc2:0001:1: None of the WOWLAN triggers enabled
[ 274.784952] mtk_vpu 10020000.vpu: vpu idle timeout
[ 274.789764] PM: dpm_run_callback(): platform_pm_suspend+0x0/0x70 returns -5
[ 274.796740] mtk_vpu 10020000.vpu: PM: failed to suspend: error -5
[ 274.802842] PM: Some devices failed to suspend, or early wake event detected
[ 275.426489] OOM killer enabled.
[ 275.429718] Restarting tasks ...
[ 275.435765] done.
[ 275.447510] PM: suspend exit
Fixes: 1f565e263c ("media: mtk-vpu: VPU should be in idle state before system is suspended")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
i.MX6 device tree include files contain dangling endpoints for the
board device tree writers' convenience. These are still included in
many existing device trees.
Treat dangling endpoints as non-existent to support them.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 612b385efb ("media: video-mux: Create media links in bound notifier")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The syscall bpf(BPF_PROG_QUERY, &attr) should use the prog_cnt field to
see how many entries user space provided and return ENOSPC if there are
more programs than that. Before this patch, this is not checked and
ENOSPC is never returned.
Note that one lirc device is limited to 64 bpf programs, and user space
I'm aware of -- ir-keytable -- always gives enough space for 64 entries
already. However, we should not copy program ids than are requested.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210623213754.632-1-sean@mess.org
Smatch static checker warns that "mdev" can be null:
sound/usb/media.c:287 snd_media_device_create()
warn: 'mdev' can also be NULL
If CONFIG_MEDIA_CONTROLLER is disabled, this file should not be included
in the build.
The below conditions in the sound/usb/Makefile are in place to ensure that
media.c isn't included in the build.
sound/usb/Makefile:
snd-usb-audio-$(CONFIG_SND_USB_AUDIO_USE_MEDIA_CONTROLLER) += media.o
select SND_USB_AUDIO_USE_MEDIA_CONTROLLER if MEDIA_CONTROLLER &&
(MEDIA_SUPPORT=y || MEDIA_SUPPORT=SND_USB_AUDIO)
The following config check in include/media/media-dev-allocator.h is
in place to enable the API only when CONFIG_MEDIA_CONTROLLER and
CONFIG_USB are enabled.
#if defined(CONFIG_MEDIA_CONTROLLER) && defined(CONFIG_USB)
This check doesn't work as intended when CONFIG_USB=m. When CONFIG_USB=m,
CONFIG_USB_MODULE is defined and CONFIG_USB is not. The above config check
doesn't catch that CONFIG_USB is defined as a module and disables the API.
This results in sound/usb enabling Media Controller specific ALSA driver
code, while Media disables the Media Controller API.
Fix the problem requires two changes:
1. Change the check to use IS_ENABLED to detect when CONFIG_USB is enabled
as a module or static. Since CONFIG_MEDIA_CONTROLLER is a bool, leave
the check unchanged to be consistent with drivers/media/Makefile.
2. Change the drivers/media/mc/Makefile to include mc-dev-allocator.o
in mc-objs when CONFIG_USB is enabled.
Link: https://lore.kernel.org/alsa-devel/YLeAvT+R22FQ%2FEyw@mwanda/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10635 image sensor embedded in the camera module is currently
reset after the MAX9271 initialization with two long delays that were
most probably not correctly characterized.
Re-work the image sensor reset procedure by holding the chip in reset
during the MAX9271 configuration, removing the long sleep delays and
only wait after the chip exits from reset for 350-500 microseconds
interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout
characterized in the chip manual.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The camera module initialization routine does not check the return
value of a few functions. Fix that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the device is identified the driver currently reports the
names of the chips embedded in the camera module.
Report the name of the camera module itself instead.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable the noise immunity threshold at the end of the rdacm20
initialization routine.
The rdacm20 camera module has been so far tested with a startup
delay that allowed the embedded MCU to program the serializer. If
the initialization routine is run before the MCU programs the
serializer and the image sensor and their addresses gets changed
by the rdacm20 driver it is required to manually enable the noise
immunity threshold to make the communication on the control channel
more reliable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no reason to allocate dynamically the 'serializer' field in
the driver structure.
Embed the field and adjust all its users in the driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current RDACM21 initialization routine powers up the OV10640 image
sensor after the OV490 ISP. The ISP is programmed with a firmware loaded
from an embedded serial flash that (most probably) tries to interact and
program also the image sensor connected to the ISP.
As described in commit "media: i2c: rdacm21: Fix OV10640 powerup" the
image sensor powerdown signal is kept high by an internal pull up
resistor and occasionally fails to startup correctly if the powerdown
line is not asserted explicitly. Failures in the OV10640 startup causes
the OV490 firmware to fail to boot correctly resulting in the camera
module initialization to fail consequentially.
Fix this by powering up the OV10640 image sensor before testing the
OV490 firmware boot completion, by splitting the ov10640_initialize()
function in an ov10640_power_up() one and an ov10640_check_id() one.
Also make sure the OV10640 identification procedure gives enough time to
the image sensor to resume after the programming phase performed by the
OV490 firmware by repeating the ID read procedure.
This commit fixes a sporadic start-up error triggered by a failure to
detect the OV490 firmware boot completion:
rdacm21 8-0054: Timeout waiting for firmware boot
[hverkuil: fixed two typos in commit log]
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10640 image sensor powerdown signal is controlled by the first
line of the OV490 GPIO pad #1, but the pad #0 identifier
OV490_GPIO_OUTPUT_VALUE0 was erroneously used. As a result the image
sensor powerdown signal was never asserted but was left floating and
kept high by an internal pull-up resistor, causing sporadic failures
during the image sensor startup phase.
Fix this by using the correct GPIO pad identifier and wait the mandatory
1.5 millisecond delay after the powerup lane is asserted. The reset
delay is not characterized in the chip manual if not as "255 XVCLK +
initialization". Wait for at least 3 milliseconds to guarantee the SCCB
bus is available.
While at it also fix the reset sequence, as the reset line was released
before the powerdown one, and the line was not cycled.
This commit fixes a sporadic start-up error triggered by a failure to
read the OV10640 chip ID:
rdacm21 8-0054: OV10640 ID mismatch: (0x01)
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a delay after the OV490 chip is put in reset state. The reset
signal shall be held low for at least 250 useconds.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
