The two debug messages in spidev_open() dereference spidev->spi without
taking the lock and without checking if it's not null. This can lead to
a crash. Drop the messages as they're not needed - the user-space will
get informed about ENOMEM with the syscall return value.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a spinlock in place that is taken in file_operations callbacks
whenever we check if spidev->spi is still alive (not null). It's also
taken when spidev->spi is set to NULL in remove().
This however doesn't protect the code against driver unbind event while
one of the syscalls is still in progress. To that end we need a lock taken
continuously as long as we may still access spidev->spi. As both the file
ops and the remove callback are never called from interrupt context, we
can replace the spinlock with a mutex.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
From: Hector Martin <marcan@marcan.st>
Date: Wed, 04 Jan 2023 18:36:26 +0900
Message-Id: <20230104093631.15611-1-marcan@marcan.st>
MIME-Version: 1.0
Content-Type: text/plain; charset="utf-8"
Content-Transfer-Encoding: 7bit
Merge changes from Hector Martin <marcan@marcan.st>:
This brings the name of the cs-setup-ns parameter which was added during
the merge window into line with other delay properties.
As mentioned in the corresponding DT binding commit, the naming scheme
for delay properties includes "delay" in the name, so let's keep that
consistent.
Fixes: 33a2fde5f7 ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230104093631.15611-3-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
If xSPI is in x2/x4/x8 mode to calculate busy
cycles, busy bits count must be divided by the number
of lanes.
If opcommand is using 8 busy bits, but SPI is
in x4 mode, there will be only 2 busy cycles.
Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
Reviewed-by: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20221219144254.20883-2-wsadowski@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the irq is enabled after the spi si registered, there can be a race
with the initialization of the devices on the spi bus.
Eg:
mtk-spi 1100a000.spi: spi-mem transfer timeout
spi-nor: probe of spi0.0 failed with error -110
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000010
...
Call trace:
mtk_spi_can_dma+0x0/0x2c
Fixes: c6f7874687 ("spi: mediatek: Enable irq when pdata is ready")
Reported-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20221225-mtk-spi-fixes-v1-0-bb6c14c232f8@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message on
fsl_spi hardware, this should be very unusual.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOmIFQACgkQJNaLcl1U
h9BD2Qf/byfpQzO+8mnDIenWP3X/WMNxJybIe1zaZXOEPRdxmE24Q7BvROnu/80C
jiKGJ3x/n5dhgnBvBJYdTw93BwDUJIcoz42WHnJMxRpxHPd/IX9N8NEOtMU5Z7T6
R/9LPpTja33CXXqbvhZw2M1dhVxbEZ9VgPVOemz0nLQtYnM4/Y8wj2RFOGgJFZ91
krY8S7VkLp6ycdv+a9ofMck+l05zpQ7TG54Nmr/0wvexosj7x7JLyZx6CahGL4/E
PMF7MDblLIrCvMtJPs2gpjHTiAReu85akoOvxBcZc5JNNynp8GXmDcOwgPRbZ7pi
bAJzH0LnwPQycTX+e46QMpViyVll7g==
=zqM3
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message
on fsl_spi hardware, this should be very unusual"
* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl_spi: Don't change speed while chipselect is active
Commit c9bfcb3151 ("spi_mpc83xx: much improved driver") made
modifications to the driver to not perform speed changes while
chipselect is active. But those changes where lost with the
convertion to tranfer_one.
Previous implementation was allowing speed changes during
message transfer when cs_change flag was set.
At the time being, core SPI does not provide any feature to change
speed while chipselect is off, so do not allow any speed change during
message transfer, and perform the transfer setup in prepare_message
in order to set correct speed while chipselect is still off.
Reported-by: Herve Codina <herve.codina@bootlin.com>
Fixes: 64ca1a034f ("spi: fsl_spi: Convert to transfer_one")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/8aab84c51aa330cf91f4b43782a1c483e150a4e3.1671025244.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
A busy enough release, but not for the core which has only seen very
small updates. The biggest addition is the readdition of support for
detailed configuration of the timings around chip selects. That had
been removed for lack of use but there's been applications found for it
on Atmel systems. Otherwise the updates are mostly feature additions
and cleanups to existing drivers.
- Provide a helper for getting device match data in a way that
abstracts away which firmware interface is being used.
- Re-add the spi_set_cs_timing() API for detailed configuration of the
timing around chip select and support it on Atmel.
- Support for MediaTek MT7986, Microchip PCI1xxxx, Nuvoton WPCM450 FIU
and Socionext F_OSPI.
There's a straightforward add/add conflict with the rpmsg tree in the
xilinx firmware code (both trees got new users of the firmware added
each needing new firmware<->kernel ioctls).
There's a cross tree merge with I2C in order to use the new
i2c_client_get_device_id() helper in some I2C attached SPI controllers
as part of their conversion to I2C's probe_new() API.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOXIt8ACgkQJNaLcl1U
h9Alrwf9F6mgj3eaDbhPH2lJ+zZRDJrdrMxT1US1tWixCMEZilntDXVecJA+/htp
/tJ0InGXsyr+6p9lXsFGQZGuaSIzKh0h2OW3JCakPGfp6HvA8+qXqHYSLKzIXtYU
/lk+kR+H6TGG+pjFtwkNnbCY/pYAlOtdjdmfui68VSsqWYX1W1kJDhDEkpUZePUx
Bc9wGgGByL0ZEHMQ/O6d8Nc/JzfTQPFuPB9ZHpIHFuPuAnjDQx+veaWejpVawy+D
8crMM7OgGpHy1hENSN786039QvNbWvVucPyVwJfU4SDhrT6oNNmEA/RF/DqTt472
8cbNG5H5bSR0Youv9ofxdP9bAOHhtg==
=eJDv
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A busy enough release, but not for the core which has only seen very
small updates. The biggest addition is the readdition of support for
detailed configuration of the timings around chip selects. That had
been removed for lack of use but there's been applications found for
it on Atmel systems. Otherwise the updates are mostly feature
additions and cleanups to existing drivers.
Summary:
- Provide a helper for getting device match data in a way that
abstracts away which firmware interface is being used.
- Re-add the spi_set_cs_timing() API for detailed configuration of
the timing around chip select and support it on Atmel.
- Support for MediaTek MT7986, Microchip PCI1xxxx, Nuvoton WPCM450
FIU and Socionext F_OSPI"
* tag 'spi-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
spi: dt-bindings: Convert Synquacer SPI to DT schema
spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
spi: spi-mtk-nor: Add recovery mechanism for dma read timeout
spi: spi-fsl-lpspi: add num-cs binding for lpspi
spi: spi-fsl-lpspi: support multiple cs for lpspi
spi: mtk-snfi: Add snfi support for MT7986 IC
spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
spi: cadence-quadspi: Add minimum operable clock rate warning to baudrate divisor calculation
spi: microchip: pci1xxxx: Add suspend and resume support for PCI1XXXX SPI driver
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix warning in example (missing reg property)
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix error in example (bogus include)
spi: mediatek: Enable irq when pdata is ready
spi: spi-mtk-nor: Unify write buffer on/off
spi: intel: Add support for SFDP opcode
spi: intel: Take possible chip address into account in intel_spi_read/write_reg()
spi: intel: Implement adjust_op_size()
spi: intel: Use ->replacement_op in intel_spi_hw_cycle()
spi: cadence: Drop obsolete dependency on COMPILE_TEST
spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings
spi: wpcm-fiu: Add direct map support
...
The addition of 3WIRE support would affect MOSI direction even
when still in standard (4 wire) mode. This can lead to MOSI being
at an invalid logic level when a device driver sets an SPI
message with a NULL tx_buf.
spi.h states that if tx_buf is NULL then "zeros will be shifted
out ... " If MOSI is tristated then the data shifted out is subject
to pull resistors, keepers, or in the absence of those, noise.
This issue came to light when using spi-gpio connected to an
ADS7843 touchscreen controller. MOSI pulled high when clocking
MISO data in caused the SPI device to interpret this as a command
which would put the device in an unexpected and non-functional
state.
Fixes: 4b859db2c6 ("spi: spi-gpio: add SPI_3WIRE support")
Fixes: 5132b3d283 ("spi: gpio: Support 3WIRE high-impedance turn-around")
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Link: https://lore.kernel.org/r/20221207230853.6174-1-kris@embeddedTS.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The state machine of MTK spi nor controller may be disturbed by some
glitch signals from the relevant BUS during dma read, Although the
possibility of causing the dma read to fail is next to nothing,
However, if error-handling is not implemented, which makes the feature
somewhat risky.
Add an error-handling mechanism here, reset the state machine and
re-read the data when an error occurs.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221207055435.30557-1-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
has changed the user-space interface so that bogus SPI_CS_HIGH started
to appear in the mask returned by SPI_IOC_RD_MODE even for active-low CS
pins. Commit 138c9c32f0
("spi: spidev: Fix CS polarity if GPIO descriptors are used") fixed only
SPI_IOC_WR_MODE part of the problem. Let's fix SPI_IOC_RD_MODE
symmetrically.
Test case:
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/spi/spidev.h>
int main(int argc, char **argv)
{
char modew = SPI_CPHA;
char moder;
int f = open("/dev/spidev0.0", O_RDWR);
if (f < 0)
return 1;
ioctl(f, SPI_IOC_WR_MODE, &modew);
ioctl(f, SPI_IOC_RD_MODE, &moder);
return moder == modew ? 0 : 2;
}
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20221130162927.539512-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This Cadence QSPI IP has a 4-bit clock divisor field
for baud rate division. For example:
0b0000 = /2
0b0001 = /4
0b0010 = /6
...
0b1111 = /32
The maximum divisor is 32
(when div = CQSPI_REG_CONFIG_BAUD_MASK).
If we assume a reference clock of 500MHz and we set
our spi-max-frequency to something low, such as 10 MHz.
The calculated bit field for the divisor ends up being:
DIV_ROUND_UP(500000000/(2*10000000))-1 = 25
25 is 0b11001... which truncates to a divisor field of 0b1001 (or /20).
This is higher than our anticipated max-frequency of 10MHz
(500MHz/20 = 25 MHz). Instead, let's make sure we're always using
the maximum divisor (/32) in this case and give the user a warning about
the rate adjustment.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Link: https://lore.kernel.org/r/20221128164147.158441-1-nathan.morrison@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the device does not come straight from reset, we might receive an IRQ
before we are ready to handle it.
Fixes:
[ 0.832328] Unable to handle kernel read from unreadable memory at virtual address 0000000000000010
[ 1.040343] Call trace:
[ 1.040347] mtk_spi_can_dma+0xc/0x40
...
[ 1.262265] start_kernel+0x338/0x42c
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221128-spi-mt65xx-v1-0-509266830665@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The logical structures of mtk_nor_write_buffer_enable and
mtk_nor_write_buffer_disable are very similar, So it is necessary to
combine them into one.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20221115124655.10124-1-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Intel SPI-NOR controller supports SFDP (Serial Flash Discoverable
Parameter) opcode so add it to the list of supported opcodes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-5-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows us to get rid of the checks in the intel_spi_[sh]w_cycle()
and makes it possible for the SPI-NOR core to split the transaction into
smaller chunks as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmNoPiAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGPmcH/2dl4Zu+ofzwziH4
MxIHeSdL62tFEtD+643hTArXLR/8YeZkt17q0vaQa0WQFC09vtYepdvAuiQIGrDm
69hXY20BIARz1bwqmGuP+gNhjFeuHVy5B9qIKV7z0HoO3Guf2BoAG14LEEBsc5SO
RrZSVDRlGHnstMBx4zplWDNXOxehumwoPInFyKC8SqDg464BCeo/ErJbzwMXPdBw
RPUuDh3m9iwN6BhjlbM9UhtNEbakVKw+LaTO5eYtiPValyJ40ws/wQ/SrDc/k9YA
1E1gFlUMgPwNz0uVBEO+NcRRsQHiBqrEyLDpvg5RkE2xnOJwMrm9LDY6RqwJD/w1
4UKcuAs=
=ls46
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOBFIEACgkQJNaLcl1U
h9A4zAgAgVnP6727ptBIpTE55chOrOPyeVI0bE1xAZ3jyBEfqCFk9yb7wmr9NZY4
tJkuRlBlDGFVvpYavk18m8ZbwaedGqYfRqxmWSFdq19dmbSXn6DdZglrtf19zN2S
eNEFSbp/CAjxZAGAdoErf3VjFOHyEt8sm4K6443BbkvKhObKAR5Np2tlEURV2ezJ
UAJZXcc+Muu273nH5aaXpKyagL/kupeUns5kcJ73sK3qozxvjrEh8vHhRHx+CQAH
qmEqe8dovBWxZUXr7rYDia3xVxCeZGjIQIRsJX/9oA3YuU9entNZx3QeGlMRvue8
wTlhLVYhO+WlB2AfYtOAPNyJAizttA==
=CYxU
-----END PGP SIGNATURE-----
Merge tag 'v6.1-rc4' into spi-6.2
Linux 6.1-rc4 which should get my CI working on RPi3s again.
Merge series from Jonathan Neuschäfer <j.neuschaefer@gmx.net>:
This patchset adds DT bindings and a driver for the Flash Interface Unit
(FIU), the SPI flash controller in the Nuvoton WPCM450 BMC SoC. It
supports four chip selects, and direct (memory-mapped) access to 16 MiB
per chip. Larger flash chips can be accessed by software-defined SPI
transfers.
The existing NPCM7xx FIU driver is sufficitently incompatible with the
WPCM450 FIU that I decided to write a new driver.
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221125083114.67e7f83c@endymion.delvare
Signed-off-by: Mark Brown <broonie@kernel.org>
Besides software controlled SPI transfers (UMA, "user mode access"), FIU
also supports a 16 MiB mapping window per attached flash chip.
This patch implements direct mapped read access, to speed up flash reads.
Without direct mapping:
# time dd if=/dev/mtd0ro of=dump bs=1M
16+0 records in
16+0 records out
real 1m 47.74s
user 0m 0.00s
sys 1m 47.75s
With direct mapping:
# time dd if=/dev/mtd0ro of=dump bs=1M
16+0 records in
16+0 records out
real 0m 30.81s
user 0m 0.00s
sys 0m 30.81s
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-4-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The Flash Interface Unit (FIU) is the SPI flash controller in the
Nuvoton WPCM450 BMC SoC. It supports four chip selects, and direct
(memory-mapped) access to 16 MiB per chip. Larger flash chips can be
accessed by software-defined SPI transfers.
The FIU in newer NPCM7xx SoCs is not compatible with the WPCM450 FIU.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-3-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
This series adds dt-bindings and a driver for Socionext F_OSPI controller
for connecting an SPI Flash memory over up to 8-bit wide bus.
The controller supports up to 4 chip selects.
Introduce Socionext F_OSPI controller driver. This controller is used to
communicate with slave devices such as SPI Flash memories. It supports
4 slave devices and up to 8-bit wide bus, but supports master mode only.
This driver uses spi-mem framework for SPI flash memory access, and
can only operate indirect access mode and single data rate mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221124003351.7792-3-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few fixes, all device specific. The most important ones are for the
i.MX driver which had a couple of nasty data corruption inducing errors
appear after the change to support PIO mode in the last merge window
(one introduced by the change and one latent one which the PIO changes
exposed), thanks to Frieder, Fabio, Marc and Marek for jumping on that
and resolving the issues quickly once they were found.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmN+RHAACgkQJNaLcl1U
h9AcOQf9HQbm5UxLbb2+ufC96M/XyCPAunOFPfIKsIEIZSQuM/abdb+jwV34kn/I
ApnFrEOz6/4i9iDotpf6fCe037r07vuy2bJSHCmszgE0xEvCfioGf/ssxw+eaQf7
GmDnCy9cnyIe0SS8x0+oOUGj4Mi3pLBZmLUr6nU2W3BwGkUXM3BXk3qTKvTi2B10
XFwnNI+hImni2KrVSkpKgCr6v0WQ/phwtnbRw/YeiGzhaF/427llgqd/mJCgmFkk
WStH83DdGke0qUF+AqFppfDVMsH5+r47tAaaDuBNRLSxDbLsOsHm4YetO+nFs7BK
JqDIzECtVPcXKhaWDdIiDoVQkt1YPg==
=k58Q
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few fixes, all device specific.
The most important ones are for the i.MX driver which had a couple of
nasty data corruption inducing errors appear after the change to
support PIO mode in the last merge window (one introduced by the
change and one latent one which the PIO changes exposed).
Thanks to Frieder, Fabio, Marc and Marek for jumping on that and
resolving the issues quickly once they were found"
* tag 'spi-fix-v6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-imx: spi_imx_transfer_one(): check for DMA transfer first
spi: tegra210-quad: Fix duplicate resource error
spi: dw-dma: decrease reference count in dw_spi_dma_init_mfld()
spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock
spi: mediatek: Fix DEVAPC Violation at KO Remove
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-566-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-565-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The at91 QSPI IP uses a default value of half of the period of the QSPI
clock period for the cs-setup time, which is not always enough, an example
being the sst26vf064b SPI NOR flash which requires a minimum cs-setup time
of 5 ns. It was observed that none of the at91 SoCs can fulfill the
minimum CS setup time for the aforementioned flash, as they operate at
high frequencies and half a period does not suffice for the required CS
setup time. Add support for configuring the CS timing in the controller.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-5-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4ccf359849 ("spi: remove spi_set_cs_timing()"), removed the
method as noboby used it. Nobody used it probably because some SPI
controllers use some default large cs-setup time that covers the usual
cs-setup time required by the spi devices. There are though SPI controllers
that have a smaller granularity for the cs-setup time and their default
value can't fulfill the spi device requirements. That's the case for the
at91 QSPI IPs where the default cs-setup time is half of the QSPI clock
period. This was observed when using an sst26vf064b SPI NOR flash which
needs a spi-cs-setup-ns = <7>; in order to be operated close to its maximum
104 MHz frequency.
Call spi_set_cs_timing() in spi_setup() just before calling spi_set_cs(),
as the latter needs the CS timings already set.
If spi->controller->set_cs_timing is not set, the method will return 0.
There's no functional impact expected for the existing drivers. Even if the
spi-mt65xx.c and spi-tegra114.c drivers set the set_cs_timing method,
there's no user for them as of now. The only tested user of this support
will be a SPI NOR flash that comunicates with the Atmel QSPI controller for
which the support follows in the next patches.
One will notice that this support is a bit different from the one that was
removed in commit 4ccf359849 ("spi: remove spi_set_cs_timing()"),
because this patch adapts to the changes done after the removal: the move
of the cs delays to the spi device, the retirement of the lelgacy GPIO
handling. The mutex handling was removed from spi_set_cs_timing() because
we now always call spi_set_cs_timing() in spi_setup(), which already
handles the spi->controller->io_mutex, so use the mutex handling from
spi_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-4-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI framework checks for each transfer (with the struct
spi_controller::can_dma callback) whether the driver wants to use DMA
for the transfer. If the driver returns true, the SPI framework will
map the transfer's data to the device, start the actual transfer and
map the data back.
In commit 07e7593877 ("spi: spi-imx: add PIO polling support") the
spi-imx driver's spi_imx_transfer_one() function was extended. If the
estimated duration of a transfer does not exceed a configurable
duration, a polling transfer function is used. This check happens
before checking if the driver decided earlier for a DMA transfer.
If spi_imx_can_dma() decided to use a DMA transfer, and the user
configured a big maximum polling duration, a polling transfer will be
used. The DMA unmap after the transfer destroys the transferred data.
To fix this problem check in spi_imx_transfer_one() if the driver
decided for DMA transfer first, then check the limits for a polling
transfer.
Fixes: 07e7593877 ("spi: spi-imx: add PIO polling support")
Link: https://lore.kernel.org/all/20221111003032.82371-1-festevam@gmail.com
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Cc: David Jander <david@protonic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20221116164930.855362-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
controller data alloc is done with client device data causing duplicate
resource error. Allocate memory using controller device when using devm
Fixes: f89d2cc396 ("spi: tegra210-quad: use devm call for cdata memory")
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221117070320.18720-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the driver be able to bit-bang a GPIO for the Chip Select pin of
select peripherals.
The GPIO value is driven by the driver in that case, and none of the
hardware Chip Select bits will be populated in the PUSHR register for
the TX commands constructed for this peripheral.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221111211356.545026-1-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pci_get_device() will increase the reference count for the returned
pci_dev. Since 'dma_dev' is only used to filter the channel in
dw_spi_dma_chan_filer() after using it we need to call pci_dev_put() to
decrease the reference count. Also add pci_dev_put() for the error case.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20221116093204.46700-1-wangxiongfeng2@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e7593877 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The timeout value of the current dma read is unreasonable. For example,
If the spi flash clock is 26Mhz, It will takes about 1.3ms to read a
4KB data in spi mode. But the actual measurement exceeds 50s when a
dma read timeout is encountered.
In order to be more accurately, It is necessary to use usecs_to_jiffies,
After modification, the measured timeout value is about 130ms.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221114081327.25750-1-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A relatively large batch of fixes here but all device specific, plus an
update to MAINTAINERS. The summary print change to the STM32 driver is
fixing an issue where the driver could easily end up spamming the logs
with something that should be a debug message.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmNuPWkACgkQJNaLcl1U
h9BZJQf/Rj3kjTdwjccp+QXTrXQZVMjkXYUuLHbUokO2Mzy+U3mNCkJuvLJjAvSw
kqFBbJNYIm1jItRoqOkwlnNb0hw+QZAzBivi4DLPZJUwEeT6LxQdlYvepy6bEjCW
XJpTMFxDDaWkFUftl+tLZFN2VxHaVHEVTJ5aMu2ija0mjG1M5vrYtgVemyJ+v2/o
0nhXgnRe7Fq2+MqJazVzYs6ZxCvpIiU18a4WLD5BPGTIZhdfE0UXG+QGqWV4toHI
uZWnV+NWEKNzMGS/QdcHZYQHWlcQBR/g5kPFQFCl2D+aK9CmakHc6Bk99H6tRdLn
xYHjHafs6BwCG3eBfE/hxD8rsfTNmw==
=UfdB
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A relatively large batch of fixes here but all device specific, plus
an update to MAINTAINERS.
The summary print change to the STM32 driver is fixing an issue where
the driver could easily end up spamming the logs with something that
should be a debug message"
* tag 'spi-fix-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: amd: Fix SPI_SPD7 value
spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
spi: meson-spicc: fix do_div build error on non-arm64
spi: intel: Use correct mask for flash and protected regions
spi: mediatek: Fix package division error
spi: tegra210-quad: Don't initialise DMA if not supported
MAINTAINERS: Update HiSilicon SFC Driver maintainer
spi: meson-spicc: move wait completion in driver to take bursts delay in account
spi: stm32: Print summary 'callbacks suppressed' message
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const array ls1028a_soc_attr on the stack, instead
make it static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20221102152904.143423-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes :
error: passing argument 1 of '__div64_32' from incompatible pointer type
By passing an uint64_t as first variable to do_div().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 04694e5002 ("spi: meson-spicc: move wait completion in driver to take bursts delay in account")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221027-b4-spicc-burst-delay-fix-v2-0-8cc2bab3417a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
- step1: introduce new helpers with modern naming.
- step2: switch to use these new helpers in all drivers.
- step3: remove all legacy helpers and update all legacy names.
This patch is for step1, it introduces new helpers with host/target
naming for drivers using.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
