High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.
HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
stih407 SoC have a dedicated hardware cursor plane,
this patch enable it.
The hardware have a color look up table, fix it to
be able to use ARGB8888.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
For stih407 SoC enable the second mixer to get two CRTC.
Allow GPD planes and encoders to be connected to this new CRTC.
Cursor plane can only be set on first CRTC.
GPD clocks needed change the parent clock depending on which
CRTC GPD are used.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
The HDMI path introduce a delay of 6 pixels.
This delay should be take into account while programming
VTG for the HDMI. Without this delay, the HDMI active
window area is shift of 6 pixel on the right.
Set also timing for DVO output.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Change some functions prototype to prepare the introduction of
auxiliary crtc. It will also help to have a DVO encoder.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Make sure that vblank is enabled when crtc commit is call.
Replace drm_vblank_off() by drm_crtc_vblank_off()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
The hardware expect to have the infoframe checksum in the first byte.
In consequence shift all infoframe on one byte.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Store the physical address at node creation time
to avoid use of virt_to_dma and dma_to_virt everywhere
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Merge drm core fixes from Daniel.
* tag 'topic/core-stuff-2014-12-10' of git://anongit.freedesktop.org/drm-intel:
drm: Zero out DRM object memory upon cleanup
drm: fix a typo in a comment
drm: fix a word repetition in a comment
drm: Fix memory leak at error path of drm_read()
drm/Documentation: Fix rowspan value in drm-kms-properties
drm/edid: Restore kerneldoc consistency
drm/edid: new drm_edid_block_checksum helper function V3
drm/edid: shorten log output in case of all zeroes edid block
drm/edid: move drm_edid_is_zero to top, make edid argument const
Drivers where the DRM objects have a lifetime that extends beyond that
of the DRM device need to zero out the DRM object memory to void stale
data such as properties. The DRM core code expects to operate on newly
allocated and zeroed out objects and will behave unexpectedly, such as
add duplicate properties, otherwise.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds fbdev/con support for tiled monitors, so that we
only set a mode on the correct half of the monitor, or
span the two halves if needed.
v2: remove unneeded ERROR, fix | vs ||
Signed-off-by: Dave Airlie <airlied@redhat.com>
This takes the tiling info from the connector and
exposes it to userspace, as a blob object in a
connector property.
The contents of the blob is ABI.
v2: add property + function documentation.
v3: move property setup from previous patch.
add boilerplate + fix long line (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This creates a tile group from DisplayID block, and
stores the pieces of parsed info from the DisplayID block
into the connector.
v2: add missing signoff, add new connector bits to docs.
v3: remove some debugging.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logical ports are never going to have EDID changes,
they are used for the internal ports on MST monitors.
We cache the EDIDs from these to save time at MST probe.
v2: drop misplace tile property line, meant for other patch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
A tile group is an identifier shared by a single monitor,
DisplayID topology has 8 bytes we can use for this, just
use those for now until something else comes up in the
future. We assign these to an idr and use the idr to
tell userspace what connectors are in the same tile group.
DisplayID v1.3 says the serial number must be unique for
displays from the same manufacturer.
v2:
destroy idr (dvdhrm)
add docbook (danvet)
airlied:- not sure how to make docbook add fns to tile group section.
v3: fix missing unlock.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we unplug a dp mst branch we unreference the entire tree from
the root towards the leaves. Which is ok, since that's the way the
pointers and so also the refcounts go.
But when we drop the reference we must make sure that we remove the
branches/ports from the lists/pointers before dropping the reference.
Otherwise the get_validated functions will still return it instead
of returning NULL (which indicates a potentially on-going unplug).
The mst branch destroy gets this right for ports: First it deletes
the port from the ports list, then it unrefs. But the ports destroy
function gets it wrong: First it unrefs, then it drops the ref. Which
means a zombie mst branch can still be validate with get_validated_mstb_ref
when it shouldn't.
Fix this.
This should address a backtrace Dave dug out somewhere on unplug:
[<ffffffffa00cc262>] drm_dp_mst_get_validated_mstb_ref_locked+0x92/0xa0 [drm_kms_helper]
[<ffffffffa00cc211>] drm_dp_mst_get_validated_mstb_ref_locked+0x41/0xa0 [drm_kms_helper]
[<ffffffffa00cc2aa>] drm_dp_get_validated_mstb_ref+0x3a/0x60 [drm_kms_helper]
[<ffffffffa00cc2fb>] drm_dp_payload_send_msg.isra.14+0x2b/0x100 [drm_kms_helper]
[<ffffffffa00cc547>] drm_dp_update_payload_part1+0x177/0x360 [drm_kms_helper]
[<ffffffffa015c52e>] intel_mst_disable_dp+0x3e/0x80 [i915]
[<ffffffffa013d60b>] haswell_crtc_disable+0x1cb/0x340 [i915]
[<ffffffffa0136739>] intel_crtc_control+0x49/0x100 [i915]
[<ffffffffa0136857>] intel_crtc_update_dpms+0x67/0x80 [i915]
[<ffffffffa013fa59>] intel_connector_dpms+0x59/0x70 [i915]
[<ffffffffa015c752>] intel_dp_destroy_mst_connector+0x32/0xc0 [i915]
[<ffffffffa00cb44b>] drm_dp_destroy_port+0x6b/0xa0 [drm_kms_helper]
[<ffffffffa00cb588>] drm_dp_destroy_mst_branch_device+0x108/0x130 [drm_kms_helper]
[<ffffffffa00cb3cd>] drm_dp_port_teardown_pdt+0x3d/0x50 [drm_kms_helper]
[<ffffffffa00cdb79>] drm_dp_mst_handle_up_req+0x499/0x540 [drm_kms_helper]
[<ffffffff810d9ead>] ? trace_hardirqs_on_caller+0x15d/0x200 [<ffffffffa00cdc73>]
drm_dp_mst_hpd_irq+0x53/0xa00 [drm_kms_helper] [<ffffffffa00c7dfb>]
? drm_dp_dpcd_read+0x1b/0x20 [drm_kms_helper] [<ffffffffa0153ed8>]
? intel_dp_dpcd_read_wake+0x38/0x70 [i915] [<ffffffffa015a225>]
intel_dp_check_mst_status+0xb5/0x250 [i915] [<ffffffffa015ac71>]
intel_dp_hpd_pulse+0x181/0x210 [i915] [<ffffffffa01104f6>]
i915_digport_work_func+0x96/0x120 [i915]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
On MST systems the monitors don't appear when we set the fb up,
but plymouth opens the drm device and holds it open while they
come up, when plymouth finishes and lastclose gets called we
don't do the delayed fb probe, so the monitor never appears on the
console.
Fix this by moving the delayed checking into the mode restore.
v2: Daniel suggested that ->delayed_hotplug is set under
the mode_config mutex, so we should check it under that as
well, while we are in the area.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least on two MST devices I've tested with, when
they are link training downstream, they are totally
unable to handle aux ch msgs, so they defer like nuts.
I tried 16, it wasn't enough, 32 seems better.
This fixes one Dell 4k monitor and one of the
MST hubs.
v1.1: fixup comment (Tom).
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge rockchip GPU support.
This has a branch in common with the iommu tree, hopefully the
process works.
* 'drm_iommu_v15' of https://github.com/markyzq/kernel-drm-rockchip:
dt-bindings: video: Add documentation for rockchip vop
dt-bindings: video: Add for rockchip display subsytem
drm: rockchip: Add basic drm driver
dt-bindings: iommu: Add documentation for rockchip iommu
iommu/rockchip: rk3288 iommu driver
As discussed on irc, I'm sending a pull request with one important change:
- Disable support for 32-bit user processes. This is done due to AMD's decision
to remove support for 32-bit user processes on Linux for its HSA stack.
* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: Disable support for 32-bit user processes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhNLZAAoJEHm+PkMAQRiGAEcH/iclYDW7k2GKemMqboy+Ohmh
+ELbQothNhlGZlS1wWdD69LBiiXkkQ+ufVYFh/hC0oy0gUdfPMt5t+bOHy6cjn6w
9zOcACtpDKnqbOwRqXZjZgNmIabk7lRjbn7GK4GQqpIaW4oO0FWcT91FFhtGSPDa
tjtmGRqDmbNsqfzr18h0WPEpUZmT6MxIdv17AYDliPB1MaaRuAv1Kss05TJrXdfL
Oucv+C0uwnybD9UWAz6pLJ3H/HR9VJFdkaJ4Y0pbCHAuxdd1+swoTpicluHlsJA1
EkK5iWQRMpcmGwKvB0unCAQljNpaJiq4/Tlmmv8JlYpMlmIiVLT0D8BZx5q05QQ=
=oGNw
-----END PGP SIGNATURE-----
Merge tag 'v3.18' into drm-next
Linux 3.18
Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.
* tag 'v3.18': (57 commits)
Linux 3.18
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
uapi: fix to export linux/vm_sockets.h
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
ahci: disable MSI on SAMSUNG 0xa800 SSD
context_tracking: Restore previous state in schedule_user
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/nouveau/nouveau_drm.c
drivers/gpu/drm/radeon/radeon_cs.c
This patch checks if the process that opens the /dev/kfd device is 32-bit
process. If so, it returns -EPERM and prints a warning message in dmesg.
This is done to prevent 32-bit user processes from using amdkfd, and hence, HSA
features.
AMD's HSA userspace stack will also support only 64-bit processes on Linux.
Reviewed-by: Alexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.
* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Fixes for 3.20. I did stick the gen3/4 reset work from Ville in because we
have an awful lot of gen4 mesa hangs, and with this reset should also work
on vintage i965g/gm (we already have reset for g4x/gen4.5). So should help
to appease users suffering from these hangs. Otherwise all over.
This is the last 3.20 pull from me, from here on Jani will take over. By Ville Syrjälä (8) and others
* tag 'drm-intel-next-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Reject modeset when the same digital port is used more than once
drm/i915: mask RPS IRQs properly when disabling RPS
drm/i915: Tune down spurious CRC interrupt warning
drm/i915: Fix context object leak for legacy contexts
drm/i915/skl: Update in Gen9 multi-engine forcewake range
drm/i915/eDP: When enabling panel VDD cancel pending disable worker
drm/i915: Handle runtime pm in the CRC setup code
drm/i915: Disable crtcs gracefully before GPU reset on gen3/4
drm/i915: Grab modeset locks for GPU rest on pre-ctg
drm/i915: Implement GPU reset for g33
drm/i915: Implement GPU reset for 915/945
drm/i915: Restore the display config after a GPU reset on gen4
drm/i915: Fix gen4 GPU reset
drm/i915: Stop gathering error states for CS error interrupts
drm/i915: Disallow pin ioctl completely for kms drivers
drm/i915: Only warn the first time we attempt to mmio whilst suspended
drm/i915/chv: Enable AVI, SPD and HDMI infoframes for CHV.
drm/i915: Don't clobber crtc->new_config when nothing changes
Just three more fixes for 3.19.
This is the last request until -rc1. I will have our QA team run a full
HSA stack test on 3.19-rc1 and if we find problems, I will send a fixes pull
request.
* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: Set *buffer_ptr to NULL in case of error
amdkfd: use atomic allocations within srcu callbacks
amdkfd: use sizeof(long) granularity for the pasid bitmask
Note that the read manpages explicitly states that the read position
is undefined on error. Since EFAULT is just a userspace bug we are
therefore fine with just dropping the event on the floor.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: Add note that just dropping the event is ok.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In function acquire_packet_buffer() we may return -ENOMEM. In that case, we
should set the *buffer_ptr to NULL, so that calling functions which check the
*buffer_ptr value as a criteria for success, will know that
acquire_packet_buffer() failed.
Reviewed-by: Alexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
This seems to work well on CI boards after fixing the
last few bugs noticed by Chernovsky Oleg.
On boards with a high default fan speed this should
reduce fan noise. Manual fan control is not enabled
yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nobody is interested at which index the chunk is. What's needed is
a pointer to the chunk. Remove unused chunk_id field as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Completely unnecessary since the ww_mutex used to reserve a buffer
can detect double reservations from the same thread anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds an optional list_head parameter to ttm_eu_reserve_buffers.
If specified duplicates in the execbuf list are no longer reported as errors,
but moved to this list instead.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the that ring we are using for copies is functional
rather than the GFX ring. On newer asics we use the DMA
ring for bo moves.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Since we are now preserving the cursor across modesets, the cursor could
be left over in console if e.g. X crashed.
v2: add comment about universal plane support
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stop using the VM mutex for this
v2: fix typo in comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The BO_VA contains everything necessary.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Better match what it is actually doing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only used for duplicate check and that
can be done on the original as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only used once after initializing and that
ptr can be calculated from the BO as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only needed in radeon_crtc_cursor_set2.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting a mode seems to clear the cursor registers, so we need to
re-program them to make sure the cursor is visible.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 18df89fef2 ("drm: Decouple EDID parsing from I2C adapter")
renamed the adapter parameter of the drm_do_probe_ddc_edid function
to data but didn't update the kerneldoc accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
