unregister_winch() should use list_for_each_safe(), as it can delete from
the list.
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently CONFIG_HIGHMEM is broken on User Mode Linux. I'm not sure if it
worked ever.
It doesn't compile and this breaks randomconfig testing.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6aa85a5ae6 (omap4: 4430sdp:
enable the ehci port on 4430SDP) added code to enable EHCI
support on 4430sdp board.
Looks like the ULPI pin does not seem to be muxed properly on ES1.0
SDP and this causes the system to reboot when the ULPI PHY is
enabled.
Fix this by muxing the pin, this is the same setting for
both ES1.0 and ES2.0. Also add checking for gpio_request.
Cc: Keshava Munegowda <keshava_mgowda@ti.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is adding support for pwm1 and pwm2 devices found
on mx51.
[ this patch has been tested with pwm-backlight driver ]
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 076762aa52 is adding a macro whis is
calling imx_add_mxc_pwm() but gives it 2 parameters while it's taking only
one parameters.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds preliminary support for the alpha project AP-SH4AD-0A reference
platform (SH7786 based).
Additional platform information available at:
http://www.apnet.co.jp/product/superh/ap-sh4ad-0a.html
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the alpha project AP-SH4A-3A reference
platform (SH7785 based).
Additional paltform information available at:
http://www.apnet.co.jp/product/superh/ap-sh4a-3a.html
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The Card Detect GPIOs used on AP4EVB and Mackerel are
alwayws valid, so kill off the unused !gpio_is_valid()
case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add probe support for the sh7372 SH4AL-DSP core.
The most common use case for this is when the system
boots from the ARM core in the sh7372 and uses the
SH core for application offload as a slave CPU.
May also be used to boot the sh7372 from the SH core.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support System MMU for S5PV310 and S5PC210.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: changed SYSMMU config name]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support System MMU which supports address transition
from virtual address to physical address. Basically, each hardware
block is connected System MMU block can use directly vitrual address
when it accesses physical memory not using physical address.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: removed useless codes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently intel_idle and acpi_idle driver show double cpu_idle "exit idle"
events -> this patch fixes it and makes cpu_idle events throwing less complex.
It also introduces cpu_idle events for all architectures which use
the cpuidle subsystem, namely:
- arch/arm/mach-at91/cpuidle.c
- arch/arm/mach-davinci/cpuidle.c
- arch/arm/mach-kirkwood/cpuidle.c
- arch/arm/mach-omap2/cpuidle34xx.c
- arch/drivers/acpi/processor_idle.c (for all cases, not only mwait)
- arch/x86/kernel/process.c (did throw events before, but was a mess)
- drivers/idle/intel_idle.c (did throw events before)
Convention should be:
Fire cpu_idle events inside the current pm_idle function (not somewhere
down the the callee tree) to keep things easy.
Current possible pm_idle functions in X86:
c1e_idle, poll_idle, cpuidle_idle_call, mwait_idle, default_idle
-> this is really easy is now.
This affects userspace:
The type field of the cpu_idle power event can now direclty get
mapped to:
/sys/devices/system/cpu/cpuX/cpuidle/stateX/{name,desc,usage,time,...}
instead of throwing very CPU/mwait specific values.
This change is not visible for the intel_idle driver.
For the acpi_idle driver it should only be visible if the vendor
misses out C-states in his BIOS.
Another (perf timechart) patch reads out cpuidle info of cpu_idle
events from:
/sys/.../cpuidle/stateX/*, then the cpuidle events are mapped
to the correct C-/cpuidle state again, even if e.g. vendors miss
out C-states in their BIOS and for example only export C1 and C3.
-> everything is fine.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Robert Schoene <robert.schoene@tu-dresden.de>
CC: Jean Pihet <j-pihet@ti.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: linux-pm@lists.linux-foundation.org
CC: linux-acpi@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-perf-users@vger.kernel.org
CC: linux-omap@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
The kerneldoc for this function is at odds with the DMA-API
document, which holds, so fix it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/ia64/kernel/acpi.c:481: warning: format ‘%d’ expects type ‘int’, but argument 2 has type ‘long unsigned int’
Introduced by commit 05f2f274c8
[IA64] Avoid array overflow if there are too many cpus in SRAT table
Signed-off-by: Tony Luck <tony.luck@intel.com>
Having four variables for the same thing:
idle_halt, idle_nomwait, force_mwait and boot_option_idle_overrides
is rather confusing and unnecessary complex.
if idle= boot param is passed, only set up one variable:
boot_option_idle_overrides
Introduces following functional changes/fixes:
- intel_idle driver does not register if any idle=xy
boot param is passed.
- processor_idle.c will also not register a cpuidle driver
and get active if idle=halt is passed.
Before a cpuidle driver with one (C1, halt) state got registered
Now the default_idle function will be used which finally uses
the same idle call to enter sleep state (safe_halt()), but
without registering a whole cpuidle driver.
That means idle= param will always avoid cpuidle drivers to register
with one exception (same behavior as before):
idle=nomwait
may still register acpi_idle cpuidle driver, but C1 will not use
mwait, but hlt. This can be a workaround for IO based deeper sleep
states where C1 mwait causes problems.
Signed-off-by: Thomas Renninger <trenn@suse.de>
cc: x86@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
To make mc13783 and mc13892 share code, the register names should be
changed to fit the new macro definitions in the comming patch.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The ab8500 regulator board configuration is updated and put in an
array which can easily be used in the MFD board configuration. The
regulator board configuration is also added to the MFD
configuration in this patch.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The CLZ instruction does not alter the condition flags, so remove the
"cc" clobber from the inline asm for fls().
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_CMDLINE_FORCE is used, the warning
Ignoring unrecognised tag 0x54410009
was displayed. Change this to
Ignoring tag cmdline (using the default kernel command line)
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for dynamical allocation of imx-keypad on mx5 platform.
After moving to dynamically registration of the keypad, the keypad clock
name needs to change accordingly.
The reason is that the original mx5 keypad platform_device id was 0,
now we use id=-1 as per arch/arm/plat-mxc/devices/platform-imx-keypad.c.
Tested keypad successfully on a MX51_3DS board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mxs duart is actually an amba-pl011 device. This commit changes
the duart device code to dynamically allocate amba-pl011 device,
so that drivers/serial/amba-pl011.c can be used on mxs.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
init_fpu() (which is indirectly called by the fpu switching code) assumes
it is in process context. Rather than makeing init_fpu() use an atomic
allocation, which can cause a task to be killed, make sure the fpu is
already initialized when we enter the run loop.
KVM-Stable-Tag.
Reported-and-tested-by: Kirill A. Shutemov <kas@openvz.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Move the operation of 'writable' to set_spte() to clean up code
[avi: remove unneeded booleanification]
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It only allows to audit one guest in the system since:
- 'audit_point' is a glob variable
- mmu_audit_disable() is called in kvm_mmu_destroy(), so audit is disabled
after a guest exited
this patch fix those issues then allow to audit more guests at the same time
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of syncing the guest cr3 every exit, which is expensince on vmx
with ept enabled, sync it only on demand.
[sheng: fix incorrect cr3 seen by Windows XP]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If a pagetable contains a writeable large spte, all of its sptes will be
write protected, including non-leaf ones, leading to endless pagefaults.
Do not write protect pages above PT_PAGE_TABLE_LEVEL, as the spte fault
paths assume non-leaf sptes are writable.
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
'error' is byte sized, so use a byte register constraint.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When NX is enabled on the host but not on the guest, we use the entry/exit
msr load facility, which is slow. Optimize it to use entry/exit efer load,
which is ~1200 cycles faster.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In case of a nested page fault or an intercepted #PF newer SVM
implementations provide a copy of the faulting instruction bytes
in the VMCB.
Use these bytes to feed the instruction emulator and avoid the costly
guest instruction fetch in this case.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When the DecodeAssist feature is available, the linear address
is provided in the VMCB on INVLPG intercepts. Use it directly to
avoid any decoding and emulation.
This is only useful for shadow paging, though.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Newer SVM implementations provide the GPR number in the VMCB, so
that the emulation path is no longer necesarry to handle debug
register access intercepts. Implement the handling in svm.c and
use it when the info is provided.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Newer SVM implementations provide the GPR number in the VMCB, so
that the emulation path is no longer necesarry to handle CR
register access intercepts. Implement the handling in svm.c and
use it when the info is provided.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
the recent APM Vol.2 and the recent AMD CPUID specification describe
new CPUID features bits for SVM. Name them here for later usage.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
emulate_instruction had many callers, but only one used all
parameters. One parameter was unused, another one is now
hidden by a wrapper function (required for a future addition
anyway), so most callers use now a shorter parameter list.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
move the complete_insn_gp() helper function out of the VMX part
into the generic x86 part to make it usable by SVM.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The handling of CR8 writes in KVM is currently somewhat cumbersome.
This patch makes it look like the other CR register handlers
and fixes a possible issue in VMX, where the RIP would be incremented
despite an injected #GP.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In KVM_CREATE_IRQCHIP, kvm_io_bus_unregister_dev() is called without taking
slots_lock in the error handling path.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
If KVM sees a read-only host page, it will map it as read-only to prevent
breaking a COW. However, if the page was part of a large guest page, KVM
incorrectly extends the write protection to the entire large page frame
instead of limiting it to the normal host page.
This results in the instantiation of a new shadow page with read-only access.
If this happens for a MOVS instruction that moves memory between two normal
pages, within a single large page frame, and mapped within the guest as a
large page, and if, in addition, the source operand is not writeable in the
host (perhaps due to KSM), then KVM will instantiate a read-only direct
shadow page, instantiate an spte for the source operand, then instantiate
a new read/write direct shadow page and instantiate an spte for the
destination operand. Since these two sptes are in different shadow pages,
MOVS will never see them at the same time and the guest will not make
progress.
Fix by mapping the direct shadow page read/write, and only marking the
host page read-only.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the xsetbv intercept to the AMD part
of KVM. This makes AVX usable in a save way for the guest on
AVX capable AMD hardware.
The patch is tested by using AVX in the guest and host in
parallel and checking for data corruption. I also used the
KVM xsave unit-tests and they all pass.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Large page information has two elements but one of them, write_count, alone
is accessed by a helper function.
This patch replaces this helper function with more generic one which returns
newly named kvm_lpage_info structure and use it to access the other element
rmap_pde.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
In certain use-cases, we want to allocate guests fixed time slices where idle
guest cycles leave the machine idling. There are many approaches to achieve
this but the most direct is to simply avoid trapping the HLT instruction which
lets the guest directly execute the instruction putting the processor to sleep.
Introduce this as a module-level option for kvm-vmx.ko since if you do this
for one guest, you probably want to do it for all.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the new flush-by-asid of upcoming AMD
processors to the KVM-AMD module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch replaces all calls to force_new_asid which are
intended to flush the guest-tlb by the more appropriate
function svm_flush_tlb. As a side-effect the force_new_asid
function is removed.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function is unused and there is svm_flush_tlb which
does the same. So this function can be removed.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Retry #PF for softmmu only when the current vcpu has the same cr3 as the time
when #PF occurs
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Retry #PF is the speculative path, so don't set the accessed bit
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It's the speculative path if 'no_apf = 1' and we will specially handle this
speculative path in the later patch, so 'prefault' is better to fit the sense.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for all LBR related
state. This includes the debugctl, br_from, br_to,
last_excp_from, and last_excp_to msrs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the cr2 register in
the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit defined for the cs, ds,
ss, an es segemnts and the current cpl saved in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the base and limit
of the gdt and idt in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the dr6 and dr7
debug registers in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the CRx clean-bit for the vmcb. This
bit covers cr0, cr3, cr4, and efer.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for all nested paging
related state in the vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for all interrupt
related state in the vmcb. This corresponds to vmcb offset
0x60-0x67.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the clean-bit for the asid in the
vmcb.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the clean bit for the physical addresses of
the MSRPM and the IOPM. It does not need to be set in the
code because the only place where these values are changed
is the nested-svm vmrun and vmexit path. These functions
already mark the complete VMCB as dirty.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the clean-bit for intercepts-vectors, the
TSC offset and the pause-filter count to the appropriate
places. The IO and MSR permission bitmaps are not subject to
this bit.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the infrastructure for the implementation of
the individual clean-bits.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
One more "KVM: MMU: Don't drop accessed bit while updating an spte."
Sptes are accessed by both kvm and hardware.
This patch uses update_spte() to fix the way of removing write access.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
If we execute VMREAD during reboot we'll just skip over it. Instead of
returning garbage, return 0, which has a much smaller chance of confusing
the code. Otherwise we risk a flood of debug printk()s which block the
reboot process if a serial console or netconsole is enabled.
Signed-off-by: Avi Kivity <avi@redhat.com>
Since vmx blocks INIT signals, we disable virtualization extensions during
reboot. This leads to virtualization instructions faulting; we trap these
faults and spin while the reboot continues.
Unfortunately spinning on a non-preemptible kernel may block a task that
reboot depends on; this causes the reboot to hang.
Fix by skipping over the instruction and hoping for the best.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch replaces the open-coded vmcb-selection for the
TSC calculation with the new get_host_vmcb helper function
introduced in this patchset.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch wraps changes to the misc intercepts of SVM
into seperate functions to abstract nested-svm better and
prepare the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch wraps changes to the exception intercepts of SVM
into seperate functions to abstract nested-svm better and
prepare the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch wraps changes to the DRx intercepts of SVM into
seperate functions to abstract nested-svm better and prepare
the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch wraps changes to the CRx intercepts of SVM into
seperate functions to abstract nested-svm better and prepare
the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a function to recalculate the effective
intercepts masks when the vcpu is in guest-mode and either
the host or the guest intercept masks change.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch prevents that emulation failures which result
from emulating an instruction for an L2-Guest results in
being reported to userspace.
Without this patch a malicious L2-Guest would be able to
kill the L1 by triggering a race-condition between an vmexit
and the instruction emulator.
With this patch the L2 will most likely only kill itself in
this situation.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch replaces the is_nested logic in the SVM module
with the generic notion of guest-mode.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch introduces a generic representation of guest-mode
fpr a vcpu. This currently only exists in the SVM code.
Having this representation generic will help making the
non-svm code aware of nesting when this is necessary.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently page fault cr2 and nesting infomation are carried outside
the fault data structure. Instead they are placed in the vcpu struct,
which results in confusion as global variables are manipulated instead
of passing parameters.
Fix this issue by adding address and nested fields to struct x86_exception,
so this struct can carry all information associated with a fault.
Signed-off-by: Avi Kivity <avi@redhat.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Tested-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Immediately after we generate an exception, we want a X86EMUL_PROPAGATE_FAULT
constant, so return it from the generation functions.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of checking for X86EMUL_PROPAGATE_FAULT, check for any error,
making the callers more reliable.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If rc == X86EMUL_PROPAGATE_FAULT, we would have returned earlier.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Introduce a structure that can contain an exception to be passed back
to main kvm code.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Quote from Avi:
| I don't think we need to flush immediately; set a "tlb dirty" bit somewhere
| that is cleareded when we flush the tlb. kvm_mmu_notifier_invalidate_page()
| can consult the bit and force a flush if set.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Introduce a common function to map invalid gpte
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove it since we can judge it by using sp->unsync
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Rename it to fit its sense better
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We just need flush tlb if overwrite a writable spte with a read-only one.
And we should move this operation to set_spte() for sync_page path
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We should flush all tlbs after drop spte on sync_page path since
Quote from Avi:
| sync_page
| drop_spte
| kvm_mmu_notifier_invalidate_page
| kvm_unmap_rmapp
| spte doesn't exist -> no flush
| page is freed
| guest can write into freed page?
KVM-Stable-Tag.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The exit reason alone is insufficient to understand exactly why an exit
occured; add ISA-specific trace parameters for additional information.
Because fetching these parameters is expensive on vmx, and because these
parameters are fetched even if tracing is disabled, we fetch the
parameters via a callback instead of as traditional trace arguments.
Signed-off-by: Avi Kivity <avi@redhat.com>
exit_reason's meaning depend on the instruction set; record it so a trace
taken on one machine can be interpreted on another.
Signed-off-by: Avi Kivity <avi@redhat.com>
cea15c2 ("KVM: Move KVM context switch into own function") split vmx_vcpu_run()
to prevent multiple copies of the context switch from being generated (causing
problems due to a label). This patch folds them back together again and adds
the __noclone attribute to prevent the label from being duplicated.
Signed-off-by: Avi Kivity <avi@redhat.com>
Linear addresses are supposed to already have segment checks performed on them;
if we play with these addresses the checks become invalid.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently the x86 emulator converts the segment register associated with
an operand into a segment base which is added into the operand address.
This loss of information results in us not doing segment limit checks properly.
Replace struct operand's addr.mem field by a segmented_address structure
which holds both the effetive address and segment. This will allow us to
do the limit check at the point of access.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Failed emulation is reported via a tracepoint; the cmps printk is pointless.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Inform user to either disable TXT in the BIOS or do TXT launch
with tboot before enabling KVM since some BIOSes do not set
FEATURE_CONTROL_VMXON_ENABLED_OUTSIDE_SMX bit when TXT is enabled.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If reserved bit is set, we need inject the #PF with PFEC.RSVD=1,
but shadow_notrap_nonpresent_pte injects #PF with PFEC.RSVD=0 only
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This allows Linux to mask cpuid bits if, for example, nx is enabled on only
some cpus.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of querying cpuid directly, use the Linux accessors (boot_cpu_has,
etc.). This allows the things like the clearcpuid kernel command line to
work (when it's fixed wrt scattered cpuid bits).
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If apf is generated in L2 guest and is completed in L1 guest, it will
prefault this apf in L1 guest's mmu context.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If CR0.PG is changed, the page fault cann't be avoid when the prefault address
is accessed later
And it also fix a bug: it can retry a page enabled #PF in page disabled context
if mmu is shadow page
This idear is from Gleb Natapov
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
IA64 support forces us to abstract the allocation of the kvm structure.
But instead of mixing this up with arch-specific initialization and
doing the same on destruction, split both steps. This allows to move
generic destruction calls into generic code.
It also fixes error clean-up on failures of kvm_create_vm for IA64.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Changed makefile to use the ccflags-y option instead of EXTRA_CFLAGS.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Remove the declaration of kvm_mmu_set_base_ptes()
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
While not mandated by the spec, Linux relies on NMI being blocked by an
IF-enabling STI. VMX also refuses to enter a guest in this state, at
least on some implementations.
Disallow NMI while blocked by STI by checking for the condition, and
requesting an interrupt window exit if it occurs.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In current code, it checks async pf completion out of the wait context,
like this:
if (vcpu->arch.mp_state == KVM_MP_STATE_RUNNABLE &&
!vcpu->arch.apf.halted)
r = vcpu_enter_guest(vcpu);
else {
......
kvm_vcpu_block(vcpu)
^- waiting until 'async_pf.done' is not empty
}
kvm_check_async_pf_completion(vcpu)
^- delete list from async_pf.done
So, if we check aysnc pf completion first, it can be blocked at
kvm_vcpu_block
Fixed by mark the vcpu is unhalted in kvm_check_async_pf_completion()
path
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tracing 'async' and *pfn is useless, since 'async' is always true,
and '*pfn' is always "fault_pfn'
We can trace 'gva' and 'gfn' instead, it can help us to see the
life-cycle of an async_pf
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently the exit is unhandled, so guest halts with error if it tries
to execute INVD instruction. Call into emulator when INVD instruction
is executed by a guest instead. This instruction is not needed by ordinary
guests, but firmware (like OpenBIOS) use it and fail.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Micro optimization to avoid calling wbinvd twice on the CPU that has to
emulate it. As we might be preempted between smp_call_function_many and
the local wbinvd, the cache might be filled again so that real work
could be done uselessly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently x86's kvm_vm_ioctl_get_dirty_log() needs to allocate a bitmap by
vmalloc() which will be used in the next logging and this has been causing
bad effect to VGA and live-migration: vmalloc() consumes extra systime,
triggers tlb flush, etc.
This patch resolves this issue by pre-allocating one more bitmap and switching
between two bitmaps during dirty logging.
Performance improvement:
I measured performance for the case of VGA update by trace-cmd.
The result was 1.5 times faster than the original one.
In the case of live migration, the improvement ratio depends on the workload
and the guest memory size. In general, the larger the memory size is the more
benefits we get.
Note:
This does not change other architectures's logic but the allocation size
becomes twice. This will increase the actual memory consumption only when
the new size changes the number of pages allocated by vmalloc().
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
As suggested by Andrea, pass r/w error code to gup(), upgrading read fault
to writable if host pte allows it.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This can happen in the following scenario:
vcpu0 vcpu1
read fault
gup(.write=0)
gup(.write=1)
reuse swap cache, no COW
set writable spte
use writable spte
set read-only spte
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The EPT present/writable bits use the same position as normal
pagetable bits.
Since direct_map passes ACC_ALL to mmu_set_spte, thus always setting
the writable bit on sptes, use the generic PT_PRESENT shadow_base_pte.
Also pass present/writable error code information from EPT violation
to generic pagefault handler.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
After an interrupt injection, the PPR changes, and we have to reflect that
into the vapic. This causes a KVM_REQ_EVENT to be set, which causes the
whole interrupt injection routine to be run again (harmlessly).
Optimize by only setting KVM_REQ_EVENT if the ppr was lowered; otherwise
there is no chance that a new injection is needed.
Signed-off-by: Avi Kivity <avi@redhat.com>
ldt is never used in the kernel context; same goes for fs (x86_64) and gs
(i386). So save/restore them in the heavyweight exit path instead
of the lightweight path.
By itself, this doesn't buy us much, but it paves the way for moving vmload
and vmsave to the heavyweight exit path, since they modify the same registers.
[jan: fix copy/pase mistake on i386]
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Saving guest registers is just a memory copy, and does not need to be in the
critical section. Move outside the critical section to improve latency a
bit.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
May otherwise generates build warnings about unused
kvm_read_and_reset_pf_reason if included without CONFIG_KVM_GUEST
enabled.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
gcc 4.5 with some special options is able to duplicate the VMX
context switch asm in vmx_vcpu_run(). This results in a compile error
because the inline asm sequence uses an on local label. The non local
label is needed because other code wants to set up the return address.
This patch moves the asm code into an own function and marks
that explicitely noinline to avoid this problem.
Better would be probably to just move it into an .S file.
The diff looks worse than the change really is, it's all just
code movement and no logic change.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
It has no user outside mmu.c and also no prototype.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If guest indicates that it can handle async pf in kernel mode too send
it, but only if interrupts are enabled.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If guest can detect that it runs in non-preemptable context it can
handle async PFs at any time, so let host know that it can send async
PF even if guest cpu is not in userspace.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If async page fault is received by idle task or when preemp_count is
not zero guest cannot reschedule, so do sti; hlt and wait for page to be
ready. vcpu can still process interrupts while it waits for the page to
be ready.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Send async page fault to a PV guest if it accesses swapped out memory.
Guest will choose another task to run upon receiving the fault.
Allow async page fault injection only when guest is in user mode since
otherwise guest may be in non-sleepable context and will not be able
to reschedule.
Vcpu will be halted if guest will fault on the same page again or if
vcpu executes kernel code.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When async PF capability is detected hook up special page fault handler
that will handle async page fault events and bypass other page faults to
regular page fault handler. Also add async PF handling to nested SVM
emulation. Async PF always generates exit to L1 where vcpu thread will
be scheduled out until page is available.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Enable async PF in a guest if async PF capability is discovered.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Async PF also needs to hook into smp_prepare_boot_cpu so move the hook
into generic code.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Keep track of memslots changes by keeping generation number in memslots
structure. Provide kvm_write_guest_cached() function that skips
gfn_to_hva() translation if memslots was not changed since previous
invocation.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When page is swapped in it is mapped into guest memory only after guest
tries to access it again and generate another fault. To save this fault
we can map it immediately since we know that guest is going to access
the page. Do it only when tdp is enabled for now. Shadow paging case is
more complicated. CR[034] and EFER registers should be switched before
doing mapping and then switched back.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If a guest accesses swapped out memory do not swap it in from vcpu thread
context. Schedule work to do swapping and put vcpu into halted state
instead.
Interrupts will still be delivered to the guest and if interrupt will
cause reschedule guest will continue to run another task.
[avi: remove call to get_user_pages_noio(), nacked by Linus; this
makes everything synchrnous again]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Randomize ELF_ET_DYN_BASE, which is used when loading position
independent executables.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Randomize heap address like other architectures do already.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Helper function which tells us if a task is running in ESA mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Randomize the lower bits of the stack address like x86 and powerpc.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Shuffle code around so it looks more like x86 and powerpc.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Historically 64 bit processes use the legacy address layout. However
there is no reason why 64 bit processes shouldn't benefit from the
flexible mmap layout advantages.
Therefore just enable it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vdso object is currently always mapped with mm->mmap_base used as
requested address. In case of flexible mmap layout this means it gets
mapped above mmap_base and therefore potentially stealing a bit of
address space that is reserved for the stack.
In case of flexible mmap layout the object should be mapped below
mmap base. For legacy mmap layout above.
To fix this just don't request any specific address and let the mmap
code figure out an address that fits.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce minimum gap between stack and mmap_base to 32MB. That way there
is a bit more space for heap and mmap for tight 31 bit address spaces.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Consider stack address randomization when calulating mmap_base for
flexible mmap layout . Because of address randomization the stack
address can be up to 8MB lower than STACK_TOP.
When calculating mmap_base this isn't taken into account, which could
lead to the case that the gap between the real stack top and mmap_base
is lower than what ulimit specifies for the maximum stack size.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Generic Hardware Error Source provides a way to report platform
hardware errors (such as that from chipset). It works in so called
"Firmware First" mode, that is, hardware errors are reported to
firmware firstly, then reported to Linux by firmware. This way, some
non-standard hardware error registers or non-standard hardware link
can be checked by firmware to produce more valuable hardware error
information for Linux.
This patch adds POLL/IRQ/NMI notification types support.
Because the memory area used to transfer hardware error information
from BIOS to Linux can be determined only in NMI, IRQ or timer
handler, but general ioremap can not be used in atomic context, so a
special version of atomic ioremap is implemented for that.
Known issue:
- Error information can not be printed for recoverable errors notified
via NMI, because printk is not NMI-safe. Will fix this via delay
printing to IRQ context via irq_work or make printk NMI-safe.
v2:
- adjust printk format per comments.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7377 aka G4 processor. Use
together with a recent SDHI driver using TMIO_MMC_SDIO_IRQ
and with the MMC_CAP_SDIO_IRQ flag in the board code.
The G4EVM specific SDHI platform data is also updated to
flag SDIO capabilities.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7367 aka G3 processor. Use
together with a recent SDHI driver using TMIO_MMC_SDIO_IRQ
and with the MMC_CAP_SDIO_IRQ flag in the board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the SoC. To make sure interrupts
are handled announce the MMC_CAP_SDIO_IRQ capability
on AP4EVB. Tested with a b43-based SDIO wireless card.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7366 processor. Use together
with a recent SDHI driver using TMIO_MMC_SDIO_IRQ and
with the MMC_CAP_SDIO_IRQ flag in the board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7343 processor. Use together
with a recent SDHI driver using TMIO_MMC_SDIO_IRQ and
with the MMC_CAP_SDIO_IRQ flag in the board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables runtime PM for SDHI on ecovec.
Tested with a b43 based SDIO card.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the SoC. To make sure SDIO IRQs
are used announce the MMC_CAP_SDIO_IRQ capability
on ap325rxa.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the SoC. To make sure SDIO IRQs
are used, announce the MMC_CAP_SDIO_IRQ capability
on migor.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the SoC. To make sure interrupt
are handled announce the MMC_CAP_SDIO_IRQ capability
on ecovec, kfr2r09 and se7724.
Tested with a b43-based SDIO wireless card on ecovec.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for clock information exposed to debug-fs interface.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[kgene.kim@samsung.com: removed useless empty lines]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
TFP410 DVI chip is used to provide display out.
This chip is controlled by 2 lines:
LDO which supplies the power is controlled over gpio + 2
and the enable of the chip itself is done over gpio + 1
NOTE: the LDO is necessary for LED, serial blocks as well.
gpio + 1 was used to sense USB overcurrent in vanilla beagle.
Without this fix, the display would not function as the LDO
remains shut down.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (72 commits)
powerpc/pseries: Fix build of topology stuff without CONFIG_NUMA
powerpc/pseries: Fix VPHN build errors on non-SMP systems
powerpc/83xx: add mpc8308_p1m DMA controller device-tree node
powerpc/83xx: add DMA controller to mpc8308 device-tree node
powerpc/512x: try to free dma descriptors in case of allocation failure
powerpc/512x: add MPC8308 dma support
powerpc/512x: fix the hanged dma transfer issue
powerpc/512x: scatter/gather dma fix
powerpc/powermac: Make auto-loading of therm_pm72 possible
of/address: Use propper endianess in get_flags
powerpc/pci: Use printf extension %pR for struct resource
powerpc: Remove unnecessary casts of void ptr
powerpc: Disable VPHN polling during a suspend operation
powerpc/pseries: Poll VPA for topology changes and update NUMA maps
powerpc: iommu: Add device name to iommu error printks
powerpc: Record vma->phys_addr in ioremap()
powerpc: Update compat_arch_ptrace
powerpc: Fix PPC_PTRACE_SETHWDEBUG on PPC_BOOK3S
powerpc/time: printk time stamp init not correct
powerpc: Minor cleanups for machdep.h
...
This patch adds omap_reserve functionality to board-igep0030.c.
This patch is in similar lines to commit id 71ee7dad9b, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO reset line for Beagle XM is different from vanilla beagle
so we populate it as part of gpio update routine.
This in part fixes the issue of display not functioning on beagle XM
platform.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI enable power pin is inverted (active high) in comparison
to vanilla beagle which is active low. Handle this case conditionally.
Without this fix, Beagle XM 4 port EHCI will not function and no
networking will be available
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When adding a page to m2p_override we change the p2m of the page so we
need to also clear the old pte of the kernel linear mapping because it
doesn't correspond anymore.
When we remove the page from m2p_override we restore the original p2m of
the page and we also restore the old pte of the kernel linear mapping.
Before changing the p2m mappings in m2p_add_override and
m2p_remove_override, check that the page passed as argument is valid and
return an error if it is not.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In m2p_add_override store the original mfn into page->index and then
change the p2m mapping, setting mfns as FOREIGN_FRAME.
In m2p_remove_override restore the original mapping.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add a simple hashtable based mechanism to override some portions of the
m2p, so that we can find out the pfn corresponding to an mfn of a
granted page. In fact entries corresponding to granted pages in the m2p
hold the original pfn value of the page in the source domain that
granted it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix Moorestown VRTC fixmap placement
x86/gpio: Implement x86 gpio_to_irq convert function
x86, UV: Fix APICID shift for Westmere processors
x86: Use PCI method for enabling AMD extended config space before MSR method
x86: tsc: Prevent delayed init if initial tsc calibration failed
x86, lapic-timer: Increase the max_delta to 31 bits
x86: Fix sparse non-ANSI function warnings in smpboot.c
x86, numa: Fix CONFIG_DEBUG_PER_CPU_MAPS without NUMA emulation
x86, AMD, PCI: Add AMD northbridge PCI device id for CPU families 12h and 14h
x86, numa: Fix cpu to node mapping for sparse node ids
x86, numa: Fake node-to-cpumask for NUMA emulation
x86, numa: Fake apicid and pxm mappings for NUMA emulation
x86, numa: Avoid compiling NUMA emulation functions without CONFIG_NUMA_EMU
x86, numa: Reduce minimum fake node size to 32M
Fix up trivial conflict in arch/x86/kernel/apic/x2apic_uv_x.c
When running without an MMU, we do not need to install a mapping for the
vectors page. Attempting to do so causes a compile-time error because
install_special_mapping is not defined.
This patch adds compile-time guards to the vector mapping functions
so that we can build nommu configurations once more.
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The purpose of the minsec argument is to prevent 64-bit math overflow
when the number of cycles is multiplied up. However, the multipler
is 32-bit, and in the sched_clock() case, the cycle counter is up to
32-bit as well. So the math can never overflow.
With a value of 60, and clock rates greater than 71MHz, the calculated
multiplier is unnecessarily reduced in value, which reduces accuracy by
maybe 70ppt. It's almost not worth bothering with as the oscillator
driving the counter won't be any more than 1ppm - unless you're using
a rubidium lamp or caesium fountain frequency standard.
So, set the minsec argument to zero.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sched_clock is supposed to be initialized early - in the recently added
init_early platform hook. However, in doing so we end up calling
mod_timer() before the timer lists are initialized, resulting in an
oops.
Split the initialization in two - the part which the platform calls
early which starts things off. The addition of the timer can be
delayed until after we have more of the kernel initialized - when the
normal time sources are initialized.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-integrator/cpu.c: In function ■integrator_get■:
arch/arm/mach-integrator/cpu.c:164: warning: ■vco.s■ may be used uninitialized in this function
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change device name from "fec" to "imx28-fec", so that fec driver
can distinguish mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fraction of MHz was not being displayed correctly as the calculation
was a factor of 10 out. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The x86 fixmaps need to be all together... unfortunately the
VRTC one was misplaced.
This patch makes sure the MRST VRTC fixmap is put prior to the
__end_of_permanent_fixed_addresses marker.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
LKML-Reference: <20110111105544.24448.27607.stgit@bob.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need this for x86 MID platforms where GPIO interrupts are
used. No special magic is needed so the default 1:1 behaviour
will do nicely.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
LKML-Reference: <20110111105439.24448.69863.stgit@bob.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Westmere processors use a different algorithm for
assigning APICIDs on SGI UV systems. The location of the
node number within the apicid is now a function of the
processor type.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20110110195210.GA18737@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While both methods should work equivalently well for the native
case, the Xen Dom0 case can't reliably work with the MSR one,
since there's no guarantee that the virtual CPUs it has
available fully cover all necessary physical ones.
As per the suggestion of Robert Richter the patch only adds the
PCI method, but leaves the MSR one as a fallback to cover new
systems the PCI IDs of which may not have got added to the code
base yet.
The only change in v2 is the breaking out of the new CPI
initialization method into a separate function, as requested by
Ingo.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Robert Richter <robert.richter@amd.com>
Cc: Andreas Herrmann3 <Andreas.Herrmann3@amd.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <4D2B3FD7020000780002B67D@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit a8760ec (x86: Check tsc available/disabled in the delayed init
function) missed to prevent the setup of the delayed init function in
case the initial tsc calibration failed. This results in the same
divide by zero bug as we have seen without the tsc disabled check.
Skip the delayed work setup when tsc_khz (the initial calibration
value) is 0.
Bisected-and-tested-by: Kirill A. Shutemov <kas@openvz.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When p3_ioremap() was converted to ioremap_prot() there was some breakage
introduced where the 29-bit segmentation logic would trap the area range
and return an identity mapping without having allowed the area
specification to force mapping through page tables. This wires up a PCC
mask for pgprot verification to work out whether to short-circuit the
identity mapping on legacy parts, restoring the previous behaviour.
Reported-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently it's still possible to reference the PAGE_KERNEL_PCC pgprot
encoding on X2 TLBs which simply don't support it at all. Convert this
over to follow the nommu behaviour and simply hand back an invalid pgprot
value so we error out properly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
prefetch()/prefetchw() are supposed to take a const void * instead of a
straight void *, which the build recently started complaining about, fix
them up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The header asm/hvcall.h was previously included indirectly via
smp.h. On non-SMP systems, however, these declarations are excluded
and the build breaks. This is easily fixed by including asm/hvcall.h
directly.
The VPHN feature is only meaningful on NUMA systems that implement
the SPLPAR option, so exclude the VPHN code on systems without
SPLPAR enabled.
Also, expose unmap_cpu_from_node() on systems with SPLPAR enabled,
even if CONFIG_HOTPLUG_CPU is disabled.
Lastly, map_cpu_to_node() is now needed by VPHN to manipulate the
node masks after boot time, so remove the __cpuinit annotation to
fix a section mismatch.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Initialise the SCIF serial port to allow earlyprintk
output when using zboot.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initialise the SCIF serial port to allow earlyprintk
output when using zboot. It is based on a very similar
patched for AP4EB.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the board specific interrupt code for landisk to make
use of intc (use register_intc_controller).
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigarui.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that all of the in-tree drivers have been converted to portable I/O
accessors, we can kill off the legacy ones with extreme prejudice.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (52 commits)
Blackfin: encode cpu-rev into uImage name
Blackfin: bf54x: don't ack GPIO ints when unmasking them
Blackfin: sram_free_with_lsl: do not ignore return value of sram_free
Blackfin: boards: add missing "static" to peripheral lists
Blackfin: DNP5370: new board port
Blackfin: bf518f-ezbrd: fix dsa resources
Blackfin: move "-m elf32bfin" to general LDFLAGS
Blackfin: kgdb_test: make sure to initialize num2
Blackfin: kgdb: disable preempt schedule when running single step in kgdb
Blackfin: kgdb: disable interrupt when single stepping in ADEOS
Blackfin: SMP: kgdb: apply anomaly 257 work around
Blackfin: fix building IPIPE code when XIP is enabled
Blackfin: SMP: kgdb: flush core internal write buffer before flushinv
Blackfin: sport_uart resources: remove unused secondary RX/TX pins
Blackfin: tll6527m: fix spelling in unused code (struct name)
Blackfin: bf527-ezkit: add adau1373 chip address
Blackfin: no-mpu: fix masking of small uncached dma region
Blackfin: pm: drop irq save/restore in standby and suspend to mem callback
MAINTAINERS: update Analog Devices support info
Blackfin: dpmc.h: pull in new pll.h
...
We perform the microseconds to loops calculation using a number of
multiplies and shift rights. Each shift right rounds down the
resulting value, which can result in delays shorter than requested.
Ensure that we always round up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68knommu: Need to check __get_user()/__put_user() result
m68knommu: signal.c __user annotations
m68knommu: Equivalent of "m68k: handle new gcc's"
m68knommu: f_pcr has been gone since headers' merge
m68knommu: Don't lose state if sigframe setup fails
m68knommu: Handle multiple pending signals
m68knommu: Switch to saner sigsuspend
m68knommu: Don't bother with SA_ONESHOT
m68k: Check __get_user()/__put_user() return value
m68k: Missing syscall_trace() on sigreturn
m68k: Fix stack mangling logics in sigreturn
m68k: If we fail to set sigframe up, just leave regs alone...
m68k: Don't lose state if sigframe setup fails
m68k: Simplify the singlestepping handling in signals
m68k: Switch to saner sigsuspend()
m68k: Resetting sa_handler in local copy of k_sigaction is pointless
m68k/sun3: Kill pte_unmap() warnings
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Avoid array overflow if there are too many cpus in SRAT table
[IA64] Remove unlikely from cpu_is_offline
[IA64] irq_ia64, use set_irq_chip
[IA64] perfmon: Change vmalloc to vzalloc and drop memset.
[IA64] eliminate race condition in smp_flush_tlb_mm
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ux500: allow 5500 and 8500 to be built together
ux500: modem_irq is only for 5500
ux500: dynamic SOC detection
ux500: rename MOP board Kconfig
ux500: remove build-time changing macros
* 'msm-smp' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
msm: add SMP support for msm
msm: hotplug: support cpu hotplug on msm
msm: timer: SMP timer support for msm
msm: scm-boot: Support for setting cold/warm boot addresses
msm: Secure Channel Manager (SCM) support
Support twl4030 keypad and gpio keys on IGEP v2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second MMC channel (used by the WLAN/BT module) is not linked to
power regulator. This causes the WLAN/BT module to fail being detected if
CONFIG_REGULATOR_DUMMY is not set.
This patch adds the two regulators that actually feed the WLAN/BT module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module has one EHCI interface on board using
USB2HS port. GPIO183 is used as PHY reset.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At latest mainline commit 0c21e3aaf6, omap2plus build is broken. This
patch is trivial fix for the missed usb clock node for CK_3430ES2PLUS
flag update.
CHK include/generated/compile.h
CC arch/arm/mach-omap2/clock3xxx_data.o
arch/arm/mach-omap2/clock3xxx_data.c:3289: error: 'CK_3430ES2' undeclared
here (not in a function)
make[1]: *** [arch/arm/mach-omap2/clock3xxx_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated mask to include CK_36XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SMSC 3320 USB PHY on the OMAP4 Pandaboard needs a 19.2 MHz
reference clock. This clock is provided from the OMAP4's fref_clk3
pad.
Recent changes to clock44xx_data.c made the clock framework aware
of the existence of these fref_clk[i] lines. If the option
CONFIG_OMAP_RESET_CLOCKS is enabled in the kernel, then the
clock framework will turn these clocks off during bootup.
Explicitly request and keep this clock enabled at init for the
Pandaboard, so that the PHY receives this clock at all times.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
