The flag indicating a watchdog timeout having occurred normally persists
till Power-On Reset of the Fintek Super I/O chip. The user can clear it
by writing a `1' to the bit.
The driver doesn't offer a restart method, so regular system reboot
might not reset the Super I/O and if the watchdog isn't enabled, we
won't touch the register containing the bit on the next boot.
In this case all subsequent regular reboots will be wrongly flagged
by the driver as being caused by the watchdog.
Fix this by having the flag cleared after read. This is also done by
other drivers like those for the i6300esb and mpc8xxx_wdt.
Fixes: b97cb21a46 ("watchdog: f71808e_wdt: Fix WDTMOUT_STS register read")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200611191750.28096-5-a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The flags that should be or-ed into the watchdog_info.options by drivers
all start with WDIOF_, e.g. WDIOF_SETTIMEOUT, which indicates that the
driver's watchdog_ops has a usable set_timeout.
WDIOC_SETTIMEOUT was used instead, which expands to 0xc0045706, which
equals:
WDIOF_FANFAULT | WDIOF_EXTERN1 | WDIOF_PRETIMEOUT | WDIOF_ALARMONLY |
WDIOF_MAGICCLOSE | 0xc0045000
These were so far indicated to userspace on WDIOC_GETSUPPORT.
As the driver has not yet been migrated to the new watchdog kernel API,
the constant can just be dropped without substitute.
Fixes: 96cb4eb019 ("watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200611191750.28096-4-a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The driver supports populating bootstatus with WDIOF_CARDRESET, but so
far userspace couldn't portably determine whether absence of this flag
meant no watchdog reset or no driver support. Or-in the bit to fix this.
Fixes: b97cb21a46 ("watchdog: f71808e_wdt: Fix WDTMOUT_STS register read")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200611191750.28096-3-a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
For the sake of the easier device-driver debug procedure, we added a
DebugFS file with the controller registers state. It's available only if
kernel is configured with DebugFS support.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
DW Watchdog can rise an interrupt in case if IRQ request mode is enabled
and timer reaches the zero value. In this case the IRQ lane is left
pending until either the next watchdog kick event (watchdog restart) or
until the WDT_EOI register is read or the device/system reset. This
interface can be used to implement the pre-timeout functionality
optionally provided by the Linux kernel watchdog devices.
IRQ mode provides a two stages timeout interface. It means the IRQ is
raised when the counter reaches zero, while the system reset occurs only
after subsequent timeout if the timer restart is not performed. Due to
this peculiarity the pre-timeout value is actually set to the achieved
hardware timeout, while the real watchdog timeout is considered to be
twice as much of it. This applies a significant limitation on the
pre-timeout values, so current implementation supports either zero value,
which disables the pre-timeout events, or non-zero values, which imply
the pre-timeout to be at least half of the current watchdog timeout.
Note that we ask the interrupt controller to detect the rising-edge
pre-timeout interrupts to prevent the high-level-IRQs flood, since
if the pre-timeout happens, the IRQ lane will be left pending until
it's cleared by the timer restart.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
DW Watchdog IP core can be synthesised with asynchronous timer/APB
clocks support (WDT_ASYNC_CLK_MODE_ENABLE == 1). In this case
separate clock signals are supposed to be used to feed watchdog timer
and APB interface of the device. Currently the driver supports
the synchronous mode only. Since there is no way to determine which
mode was actually activated for device from its registers, we have to
rely on the platform device configuration data. If optional "pclk"
clock source is supplied, we consider the device working in asynchronous
mode, otherwise the driver falls back to the synchronous configuration.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In case if the DW Watchdog IP core is synthesised with
WDT_USE_FIX_TOP == false, the TOP interval indexes make the device
to load a custom periods to the counter. These periods are hardwired
at the IP synthesis stage and can be within [2^8, 2^(WDT_CNT_WIDTH - 1)].
Alas their values can't be detected at runtime and must be somehow
supplied to the driver so one could properly determine the watchdog
timeout intervals. For this purpose we suggest to have a vendor-
specific dts property "snps,watchdog-tops" utilized, which would
provide an array of sixteen counter values. At device probe stage they
will be used to initialize the watchdog device timeouts determined
from the array values and current clocks source rate.
In order to have custom TOP values supported the driver must be
altered in the following way. First of all the fixed-top values
ready-to-use array must be determined for compatibility with currently
supported devices, which were synthesised with WDT_USE_FIX_TOP == true.
It will be used if either fixed TOP feature is detected being enabled or
no custom TOPs are fetched from the device dt node. Secondly at the probe
stage we must initialize an array of the watchdog timeouts corresponding
to the detected TOPs list and the reference clock rate. For generality the
procedure of initialization is designed in a way to support the TOPs array
with no limitations on the items order or value. Finally the watchdog
period search methods should be altered to support the new timeouts data
structure.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1591945384-14587-1-git-send-email-wangqing@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1590391864-308-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
sunxi_wdt_probe() should return -ENOMEM when devm_kzalloc() fails.
Signed-off-by: Martin Wu <wuyan@allwinnertech.com>
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200529094514.26374-1-frank@allwinnertech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the dedicated function watchdog_active()
instead of the generic test_bit() function.
It is done using the following Coccinelle script:
@@
identifier wdd;
@@
- test_bit(WDOG_ACTIVE, &wdd->status)
+ watchdog_active(wdd)
Signed-off-by: Bumsik Kim <k.bumsik@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200529012428.84684-1-k.bumsik@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
New programmable logic device can have watchdog type 3 implementation.
It's same as Type 2 with extended maximum timeout period.
Maximum timeout is up-to 65535 sec.
Type 3 HW watchdog implementation can exist on all Mellanox systems.
It is differentiated by WD capability bit.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Reviewed-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200504141427.17685-4-michaelsh@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl7Xe/kACgkQ+iyteGJfRsqNGQCfeElXEDv9j+KHROxL94EYYoKP
Up8AoI/Gnhfmi/WVCyrwvfdtuAbfehcN
=72fM
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.8-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add new arm_smc_wdt watchdog driver
- da9062 and da9063 improvements
- clarify documentation about stop() that became optional
- document r8a7742 support
- some overall fixes and improvements
* tag 'linux-watchdog-5.8-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: m54xx: Add missing include
dt-bindings: watchdog: renesas,wdt: Document r8a7742 support
watchdog: Fix runtime PM imbalance on error
watchdog: riowd: remove unneeded semicolon
watchdog: Add new arm_smc_wdt watchdog driver
dt-bindings: watchdog: Add ARM smc wdt for mt8173 watchdog
watchdog: imx2_wdt: update contact email
watchdog: iTCO: fix link error
watchdog: da9062: No need to ping manually before setting timeout
watchdog: da9063: Make use of pre-configured timeout during probe
watchdog: da9062: Initialize timeout during probe
watchdog: clarify that stop() is optional
watchdog: imx_sc_wdt: Fix reboot on crash
watchdog: ts72xx_wdt: fix build error
A recent cleanup removed the mm.h include from uaccess_no.h in
m68k. This breaks the build of the m54xx watchdog driver:
drivers/watchdog/m54xx_wdt.c:49:9: error: implicit declaration of function '__raw_readl'
Due to magic include chains the inclusion of mm.h in uaccess_no.h pulled in io.h.
Include 'linux/io.h' explicitely to fix this.
Fixes: 9e86035155 ("m68knommu: Remove mm.h include from uaccess_no.h")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/87blmyjjtf.fsf@nanos.tec.linutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When watchdog_register_device() returns an error code,
a pairing runtime PM usage counter decrement is needed
to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200521080141.24373-1-dinghao.liu@zju.edu.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch adds a watchdog driver that can be used on ARM systems
with the appropriate watchdog implemented in Secure Monitor firmware.
The driver communicates with firmware via a Secure Monitor Call.
This may be useful for platforms using TrustZone that want
the Secure Monitor firmware to have the final control over the watchdog.
This is implemented on mt8173 chromebook devices oak, elm and hana in
arm trusted firmware file plat/mediatek/mt8173/drivers/wdt/wdt.c.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Evan Benn <evanbenn@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Xingyu Chen<xingyu.chen@amlogic.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200505131242.v6.2.Ia92bb4d4ce84bcefeba1d00aaa1c1e919b6164ef@changeid
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The 'pengutronix' address is defunct for years. Use the proper contact
address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200502142653.19144-1-wsa@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When the MFD driver is a loadable module, the watchdog driver fails
to get linked into the kernel:
drivers/watchdog/iTCO_wdt.o: In function `update_no_reboot_bit_pmc':
iTCO_wdt.c:(.text+0x54f): undefined reference to `intel_pmc_gcr_update'
The code is written to support operation without the MFD driver, so
add a Kconfig dependency that allows this, while disallowing the watchdog
to be built-in when the MFD driver is a module.
Fixes: 25f1ca31e2 ("platform/x86: intel_pmc_ipc: Convert to MFD")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200428212959.2993304-1-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
There is actually no need to ping the watchdog before disabling it
during timeout change. Disabling the watchdog already takes care of
resetting the counter.
This fixes an issue during boot when the userspace watchdog handler takes
over and the watchdog is already running. Opening the watchdog in this case
leads to the first ping and directly after that without the required
heartbeat delay a second ping issued by the set_timeout call. Due to the
missing delay this resulted in a reset.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200403130728.39260-3-s.riedmueller@phytec.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The watchdog might already be running during boot with a timeout set by
e.g. the bootloader. Make use of this pre-configured timeout instead of
falling back to the default timeout if no device tree value is given.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200403130728.39260-2-s.riedmueller@phytec.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
During probe try to set the timeout from device tree and fall back to
either the pre-configured timeout set by e.g. the bootloader in case the
watchdog is already running or the default value.
If the watchdog is already running make sure to update the timeout and
tell the framework about the running state to make sure the watchdog is
handled correctly until user space takes over. Updating the timeout also
removes the need for an additional manual ping so we can remove that as
well.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200403130728.39260-1-s.riedmueller@phytec.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Currently when running the samples/watchdog/watchdog-simple.c
application and forcing a kernel crash by doing:
# ./watchdog-simple &
# echo c > /proc/sysrq-trigger
The system does not reboot as expected.
Fix it by calling imx_sc_wdt_set_timeout() to configure the i.MX8QXP
watchdog with a proper timeout.
Cc: <stable@vger.kernel.org>
Fixes: 986857acbc ("watchdog: imx_sc: Add i.MX system controller watchdog support")
Reported-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Breno Lima <breno.lima@nxp.com>
Link: https://lore.kernel.org/r/20200412230122.5601-1-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If TS72XX_WATCHDOG is y and WATCHDOG_CORE is not enabled or its m,
then building fails:
drivers/watchdog/ts72xx_wdt.o: in function `ts72xx_wdt_probe':
ts72xx_wdt.c:(.text+0x14c): undefined reference to \
`watchdog_init_timeout'
ts72xx_wdt.c:(.text+0x15c): undefined reference to \
`devm_watchdog_register_device'
Select WATCHDOG_CORE to fix this.
Signed-off-by: Shyam Saini <shyam.saini@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200406215008.30468-1-shyam.saini@savoirfairelinux.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When the MFD driver is a loadable module, the watchdog driver fails
to get linked into the kernel:
drivers/watchdog/iTCO_wdt.o: In function `update_no_reboot_bit_pmc':
iTCO_wdt.c:(.text+0x54f): undefined reference to `intel_pmc_gcr_update'
The code is written to support operation without the MFD driver, so
add a Kconfig dependency that allows this, while disallowing the watchdog
to be built-in when the MFD driver is a module.
Fixes: 25f1ca31e2 ("platform/x86: intel_pmc_ipc: Convert to MFD")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts the Intel MID watchdog driver over the new SCU IPC API
where the SCU IPC instance is passed to the functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The restart handler is missing two things, first, the registers
has to be unlocked and second there is no synchronization for the
write_relaxed() calls.
This was tested on a custom board with the NXP LS1028A SoC.
Fixes: 6c5c0d48b6 ("watchdog: sp805: add restart handler")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200327162450.28506-1-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Texas Instruments K3 SoCs contain an RTI (Real Time Interrupt) module
which can be used as a watchdog. This IP provides a support for
windowed watchdog mode, in which the watchdog must be petted within
a certain time window. If it is petted either too soon, or too late,
a watchdog error will be triggered.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200312095808.19907-4-t-kristo@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The RAVE watchdog is not a full system watchdog, but is used to reset
ethernet switch when required. Change the name to better reflect this
usage.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200313101138.25915-1-l.stach@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the heartbeat module param is not specified we would get an error
message
watchdog: f1020300.watchdog: driver supplied timeout (4294967295) out of range
watchdog: f1020300.watchdog: falling back to default timeout (171)
This is because we were initialising heartbeat to -1. By removing the
initialisation (thus letting the C run time initialise it to 0) we
silence the warning message and the default timeout is still used.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200313031312.1485-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Currently the watchdog core does not initialize the last_hw_keepalive
time during watchdog startup. This will cause the watchdog to be pinged
immediately if enough time has passed from the system boot-up time, and
some types of watchdogs like K3 RTI does not like this.
To avoid the issue, setup the last_hw_keepalive time during watchdog
startup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200302200426.6492-3-t-kristo@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
.remove callback implementation doesn' call clk_disable_unprepare() which
is buggy, actually, we can just use devm_watchdog_register_device() and
devm_add_action_or_reset() to handle all necessary operations for remove
action, then .remove callback can be dropped.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1582512687-13312-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Many watchdog drivers use watchdog_stop_on_reboot() helper in order
to stop the watchdog on system reboot. Unfortunately, this logic is
coded in driver's probe function and doesn't allows user to decide what
to do during shutdown/reboot.
On the other side, Xen and Qemu watchdog drivers (xen_wdt and i6300esb)
may be configured to either send NMI or turn off/reboot VM as
the watchdog action. As the kernel may stuck at any state, sending NMIs
can't reliably reboot the VM.
At Arista, we benefited from the following set-up: the emulated watchdogs
trigger VM reset and softdog is set to catch less severe conditions to
generate vmcore. Just before reboot watchdog's timeout is increased
to some good-enough value (3 mins). That keeps watchdog always running
and guarantees that VM doesn't stuck.
Provide new stop_on_reboot module parameter to let user control
watchdog's reboot policy.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200223114939.194754-1-dima@arista.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
An attempt to convert the driver to using GPIO descriptors
(see Link tag) was discouraged in favor of deleting the
handling of the update GPIO altogehter since there are
no in-tree users.
This patch deletes the GPIO handling instead.
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-watchdog/20200210102209.289379-1-linus.walleij@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200229115046.57781-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
There is nothing in use from init.h/reboot.h, remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1582250430-8872-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The DT or ACPI tables should tell the driver what the irq flags are.
Given that this driver probes only on DT based platforms and those DT
platforms specify the irq flags we can safely drop the forced irq flag
setting here.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200220002047.115000-1-swboyd@chromium.org
[groeck: Context conflict resolution]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Some platform like ipq806x doesn't support pretimeout and define
some interrupts used by qcom,msm-timer. Change the driver to check
and use pretimeout only on qcom,kpss-wdt as it's the only platform
that actually supports it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200204195648.23350-1-ansuelsmth@gmail.com
[groeck: Conflict resolution]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The iTCO_wdt driver only needs ICH_RES_IO_SMI I/O resource when either
turn_SMI_watchdog_clear_off module parameter is set to match ->iTCO_version
(or higher), and when legacy iTCO_vendorsupport is set. Modify the driver
so that ICH_RES_IO_SMI is optional if the two conditions are not met.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation for making ->smi_res optional the iTCO_wdt driver needs
to know whether vendorsupport is being set to non-zero. For this reason
export the variable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix a couple of configuration issues in the ACPI watchdog (WDAT)
driver (Mika Westerberg) and make it possible to disable that
driver at boot time in case it still does not work as
expected (Jean Delvare).
-----BEGIN PGP SIGNATURE-----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=eIlw
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Fix a couple of configuration issues in the ACPI watchdog (WDAT)
driver (Mika Westerberg) and make it possible to disable that driver
at boot time in case it still does not work as expected (Jean
Delvare)"
* tag 'acpi-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: watchdog: Set default timeout in probe
ACPI: watchdog: Fix gas->access_width usage
ACPICA: Introduce ACPI_ACCESS_BYTE_WIDTH() macro
ACPI: watchdog: Allow disabling WDAT at boot
Since commit 057b52b4b3 ("watchdog: da9062: make restart handler atomic
safe"), the driver calls i2c functions directly. It now therefore depends
on I2C. This is a hard dependency which overrides COMPILE_TEST.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 057b52b4b3 ("watchdog: da9062: make restart handler atomic safe")
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Cc: Stefan Lengfeld <contact@stefanchrist.eu>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This fixes commit f6c98b0838 ("watchdog: da9062: add power management
ops"). During discussion [1] we agreed that this should be configurable
because it is a device quirk if we can't use the hw watchdog auto
suspend function.
[1] https://lore.kernel.org/linux-watchdog/20191128171931.22563-1-m.felsch@pengutronix.de/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: f6c98b0838 ("watchdog: da9062: add power management ops")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200207071518.5559-1-m.felsch@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The da9062 hw has a minimum ping cool down phase of at least 200ms. The
driver takes that into account by setting the min_hw_heartbeat_ms to
300ms and the core guarantees that the hw limit is observed for the
ping() calls. But the core can't guarantee the required minimum ping
cool down phase if a stop() command is send immediately after the ping()
command. So it is not allowed to ping the watchdog within the stop()
command as the driver does. Remove the ping can be done without doubts
because the watchdog gets disabled anyway and a (re)start resets the
watchdog counter too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200120091729.16256-1-m.felsch@pengutronix.de
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
