Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:
Dummy-TX - RX - Dummy-TX - RX - ...
But since RFE actually stays high after some Dummy-TX, it rather looks like:
Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)
The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.
This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The I2C Control Register bits RFDAIE and RFFIE were mixed up. In addition to
this fix, this patch adds the missing bit DRSIE for completeness.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().
Based on an earlier fix from Michael Lawnick.
Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The CONFIG_PM doesn't actually enable any of the PM callbacks, it
only allows to enable CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME.
This means if CONFIG_PM is used to protect system sleep callbacks
then it may end up unreferenced if only runtime PM is enabled.
Hence protecting sleep callbacks with CONFIG_PM_SLEEP.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The master_xfer function returns 0 on success. It should return the number of
successful transactions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In omap_i2c_xfer(), ensure pm_runtime_put() is called, even on
failure.
Without this, after a failed xfer, the runtime PM usecount will have
been incremented, but not decremented causing the usecount to never
reach zero after a failure. This keeps the device always runtime PM
enabled which keeps the enclosing power domain active, and prevents
full-chip retention/off from happening during idle.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
At this moment in time there is only one known configuration for the
Nomadik I2C driver. By not holding that configuration in the driver
adds some unnecessary overhead in platform code. The configuration
has already been removed from platform code, this patch checks for any
over-riding configurations. If there aren't any, the default is used.
[LinusW says: "Right now this is causing boot regressions so we need it
badly..."]
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Pull media updates from Mauro Carvalho Chehab:
"This is the first part of the media patches for v3.6.
This patch series contain:
- new DVB frontend: rtl2832
- new video drivers: adv7393
- some unused files got removed
- a selection API cleanup between V4L2 and V4L2 subdev API's
- a major redesign at v4l-ioctl2, in order to clean it up
- several driver fixes and improvements."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (174 commits)
v4l: Export v4l2-common.h in include/linux/Kbuild
media: Revert "[media] Terratec Cinergy S2 USB HD Rev.2"
[media] media: Use pr_info not homegrown pr_reg macro
[media] Terratec Cinergy S2 USB HD Rev.2
[media] v4l: Correct conflicting V4L2 subdev selection API documentation
[media] Feature removal: V4L2 selections API target and flag definitions
[media] v4l: Unify selection flags documentation
[media] v4l: Unify selection flags
[media] v4l: Common documentation for selection targets
[media] v4l: Unify selection targets across V4L2 and V4L2 subdev interfaces
[media] v4l: Remove "_ACTUAL" from subdev selection API target definition names
[media] V4L: Remove "_ACTIVE" from the selection target name definitions
[media] media: dvb-usb: print mac address via native %pM
[media] s5p-tv: Use module_i2c_driver in sii9234_drv.c file
[media] media: gpio-ir-recv: add allowed_protos for platform data
[media] s5p-jpeg: Use module_platform_driver in jpeg-core.c file
[media] saa7134: fix spelling of detach in label
[media] cx88-blackbird: replace ioctl by unlocked_ioctl
[media] cx88: don't use current_norm
[media] cx88: fix a number of v4l2-compliance violations
...
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
pxa i2c also has these dummy macros defined locally. Remove them as they
aren't required anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Pull embedded i2c changes from Wolfram Sang:
"Changes for the "embedded" part of the I2C subsystem:
- lots of devicetree conversions of drivers (and preparations for
that)
- big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
- Rafael's struct dev_pm_ops conversion patches for I2C
- usual driver cleanups and fixes
All patches have been in linux-next for an apropriate time and all
patches touching files outside of i2c-folders should have proper acks
from the maintainers."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
I2C: MV64XYZ: Add Device Tree support
i2c: stu300: use devm managed resources
i2c: i2c-ocores: support for 16bit and 32bit IO
V4L/DVB: mfd: use reg_shift instead of regstep
i2c: i2c-ocores: Use reg-shift property
i2c: i2c-ocores: DT bindings and minor fixes.
i2c: mv64xxxx: remove EXPERIMENTAL tag
i2c-s3c2410: Use plain pm_runtime_put()
i2c: s3c2410: Fix pointer type passed to of_match_node()
i2c: mxs: Set I2C timing registers for mxs-i2c
i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
i2c:i2c-bfin-twi: include twi head file
i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
i2c-mv64xxxx: allow more than one driver instance
...
Conflicts:
drivers/i2c/busses/i2c-nomadik.c
This reverts commit 7c86d44cda.
Stephen says:
IIRC, I proposed it before solely to solve some suspend/resume ordering
issues, and Colin Cross NAKd it. These days, deferred probe should make
this change unnecessary.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Generate a stop condition after each message marked with I2C_M_STOP.
[JD: Add I2C_FUNC_PROTOCOL_MANGLING.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Adapter drivers might support only a subset of the SMBus operations
natively. Those drivers currently have to manually emulate unsupported
operations using I2C.
Make the i2c_smbus_xfer() function fall back to
i2c_smbus_xfer_emulated() when the adapter's .smbus_xfer() operation
returns -EOPNOTSUPP, like it already does when the .smbus_xfer()
operation isn't available at all.
[JD: Minor optimization.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SCCB is a serial communication bus developed by Omnivision. Its 2-wire
mode is very similar to SMBus byte data transactions, but requires the
controller to ignore the ACK bit and to insert a stop condition after
each message.
Add a device SCCB flag and a message stop flag to be passed to
controller drivers.
[JD: Kill rogue definition in go7007 driver.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Robofuzz OSIF is a generic USB/iIC interface that embeds an ATMega8A
AVR-RISC microcontroler.
The device is based upon Till Harbaum's i2c-tiny-usb and although it
enhances the original design with further functionnalities it still
maintain compatibility with it with respect to the USB/I2C interface.
Signed-off-by: Emmanuel Deloget <logout@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Byte-by-byte transactions are used primarily for accessing I2C devices
with an SMBus controller. For these transactions, for each byte that is
read or written, the SMBus controller generates a BYTE_DONE IRQ. The isr
reads/writes the next byte, and clears the IRQ flag to start the next byte.
On the penultimate IRQ, the isr also sets the LAST_BYTE flag.
There is no locking around the cmd/len/count/data variables, since the
I2C adapter lock ensures there is never multiple simultaneous transactions
for the same device, and the driver thread never accesses these variables
while interrupts might be occurring.
The end result is faster I2C block read and write transactions.
Note: This patch has only been tested and verified by doing I2C read and
write block transfers on Cougar Point 6 Series PCH, as well as I2C read
block transfers on ICH5.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable interrupts on more devices. ICH5, ICH7(-M) and ICH10 have been
tested to work OK. ICH8 and ICH9 are expected to work just fine as
they are very close to ICH7 and ICH10.
Ultimately we want to enable this feature on at least every device
since the ICH5, but for now we limit the exposure. We'll enable it for
other devices if we don't get negative feedback.
As a bonus, let the user know when interrupts are used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Add a new 'feature' to i2c-i801 to enable using PCI interrupts.
When the feature is enabled, then an isr is installed for the device's
PCI IRQ.
An I2C/SMBus transaction is always terminated by one of the following
interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR.
When the isr fires for one of these cases, it sets the ->status variable
and wakes up the waitq. The waitq then saves off the status code, and
clears ->status (in preparation for some future transaction).
The SMBus controller generates an INTR irq at the end of each
transaction where INTREN was set in the HST_CNT register.
No locking is needed around accesses to priv->status since all writes to
it are serialized: it is only ever set once in the isr at the end of a
transaction, and cleared while no interrupts can occur. In addition, the
I2C adapter lock guarantees that entire I2C transactions for a single
adapter are always serialized.
For this patch, the INTREN bit is set only for SMBus block, byte and word
transactions, but not for I2C reads or writes. The use of the DS
(BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in
a subsequent patch.
The interrupt feature has only been enabled for COUGARPOINT hardware.
In addition, it is disabled if SMBus is using the SMI# interrupt.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
(Based on earlier work by Daniel Kurtz.)
Come up with a consistent, driver-wide strategy for event polling. For
intermediate steps of byte-by-byte block transactions, check for
BYTE_DONE or any error flag being set. At the end of every transaction
(regardless of PEC being used), check for both BUSY being cleared and
INTR or any error flag being set. This ensures proper action for all
transaction types.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Later patches enable interrupts. This preliminary patch removes the older
unsupported ENABLE_INT9 flag.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename the SMBHSTCNT register bit access constants to match the style of
other register bits.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If an error is detected in the polling loop, abort the transaction and
return an error code.
* DEV_ERR is set if the device does not respond with an acknowledge, and
the SMBus controller times out (minimum 25ms).
* BUS_ERR is set if a bus arbitration collision is detected. In other
words, when the SMBus controller tries to generate a START condition, but
detects that the SMBDATA is being held low, usually by another SMBus/I2C
master.
* FAILED is only set if a transaction is stopped by software (using
the SMBHSTCNT KILL bit).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Writing back the whole status register could clear unwanted bits.
In particular, it could clear the "INUSE_STS" bit, which is a
'hardware semaphore', that might be useful to use some day.
To prepare for this, let's ban writing back the whole status to register
HST_STS, of which this is the only instance.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As a slight optimization, pull some logic out of the polling loop during
byte-by-byte transactions by just setting the I801_LAST_BYTE bit, as
defined in the i801 (PCH) datasheet, when reading the last byte of a
byte-by-byte I2C_SMBUS_READ.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Using module_i2c_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some AMD chipsets, such as the SP5100, have an auxiliary SMBus
controller with a second set of registers. This patch adds
support for this auxiliary controller.
Tested on ASUS KCMA-D8 motherboard.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some chipsets have multiple sets of SMBus registers each controlling a
separate SMBus. Supporting these chipsets properly will require registering
multiple I2C adapters for one piix4.
The code to initialize and register the i2c_adapter structure has been
separated from piix4_probe and allows registration of a piix4 adapter
given its base address. Note that the i2c_adapter and i2c_piix4_adapdata
structures are now dynamically allocated.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some chipsets have multiple sets of piix4-compatible SMBus registers.
Eliminating the global variable will allow these chipsets to be fully
supported.
Return value from piix4_setup and piix4_sb800_setup now returns the smba
value detected. This is stored in a struct i2c_piix4_adapdata. Thus
the global variable is eliminated.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the drivers in drivers/i2c/busses/* to usemodule_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Olof Johansson <olof@lixom.net>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>
My old e-mail address won't be valid for much longer. Time to update it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull powerpc updates from Benjamin Herrenschmidt:
"Notable highlights:
- iommu improvements from Anton removing the per-iommu global lock in
favor of dividing the DMA space into pools, each with its own lock,
and hashed on the CPU number. Along with making the locking more
fine grained, this gives significant improvements in multiqueue
networking scalability.
- Still from Anton, we know provide a vdso based variant of getcpu
which makes sched_getcpu with the appropriate glibc patch something
like 18 times faster.
- More anton goodness (he's been busy !) in other areas such as a
faster __clear_user and copy_page on P7, various perf fixes to
improve sampling quality, etc...
- One more step toward removing legacy i2c interfaces by using new
device-tree based probing of platform devices for the AOA audio
drivers
- A nice series of patches from Michael Neuling that helps avoiding
confusion between register numbers and litterals in assembly code,
trying to enforce the use of "%rN" register names in gas rather
than plain numbers.
- A pile of FSL updates
- The usual bunch of small fixes, cleanups etc...
You may spot a change to drivers/char/mem. The patch got no comment
or ack from outside, it's a trivial patch to allow the architecture to
skip creating /dev/port, which we use to disable it on ppc64 that
don't have a legacy brige. On those, IO ports 0...64K are not mapped
in kernel space at all, so accesses to /dev/port cause oopses (and
yes, distros -still- ship userspace that bangs hard coded ports such
as kbdrate)."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/mpic: Create a revmap with enough entries for IPIs and timers
Remove stale .rej file
powerpc/iommu: Fix iommu pool initialization
powerpc/eeh: Check handle_eeh_events() return value
powerpc/85xx: Add phy nodes in SGMII mode for MPC8536/44/72DS & P2020DS
powerpc/e500: add paravirt QEMU platform
powerpc/mpc85xx_ds: convert to unified PCI init
powerpc/fsl-pci: get PCI init out of board files
powerpc/85xx: Update corenet64_smp_defconfig
powerpc/85xx: Update corenet32_smp_defconfig
powerpc/85xx: Rename P1021RDB-PC device trees to be consistent
powerpc/watchdog: move booke watchdog param related code to setup-common.c
sound/aoa: Adapt to new i2c probing scheme
i2c/powermac: Improve detection of devices from device-tree
powerpc: Disable /dev/port interface on systems without an ISA bridge
of: Improve prom_update_property() function
powerpc: Add "memory" attribute for mfmsr()
powerpc/ftrace: Fix assembly trampoline register usage
powerpc/hw_breakpoints: Fix incorrect pointer access
powerpc: Put the gpr save/restore functions in their own section
...
Clock support is moving to the clk subsystem. These tegra, omap and imx
changes are for code that is still platform specific and not (yet)
part of that subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cvpa
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
The I.MX platform is getting converted to use sparse IRQs. We are doing
this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Y2Sm
-----END PGP SIGNATURE-----
Merge tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc sparse IRQ conversion from Arnd Bergmann:
"The I.MX platform is getting converted to use sparse IRQs. We are
doing this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea."
* tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
Extends the driver to get properties from device tree. Rather than
pass the N & M factors in DT, use the more standard clock-frequency
property. Calculate N & M at run time. In order to do this, we need to
know tclk. So the driver uses clk_get() etc in order to get the clock
and clk_get_rate() to determine the tclk rate. Not all platforms
however have CLK, so some #ifdefery is needed to ensure the driver
still compiles when CLK is not available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[wsa: converted some ints to u32 to match signedness]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There are three parts to this:
1) Remove the definitions of OCTEON_IRQ_TWSI and OCTEON_IRQ_TWSI2.
The interrupts are specified by the device tree and these hard
coded irq numbers block the used of the irq lines by the irq_domain
code.
2) Remove platform device setup code from octeon-platform.c, it is
now unused.
3) Convert i2c-octeon.c to use device tree. Part of this includes
using the devm_* functions instead of the raw counterparts, thus
simplifying error handling. No functionality is changed.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3939/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Allocate memory for device state using devm_kzalloc(), get the
clock using devm_clk_get(), get the IRQ using devm_request_irq(),
request and remap memory using devm_request_and_ioremap().
All to simplify accounting and letting the kernel do the
garbage-collection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some architectures supports only 16-bit or 32-bit read/write access to
their IO space. Add a 'reg-io-width' platform and OF parameter which
specifies the IO width to support these platforms.
reg-io-width can be specified as 1, 2 or 4, and has a default value
of 1 if it is unspecified.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Deprecate 'regstep' property and use the standard 'reg-shift' property
for register offset shifts. 'regstep' will still be supported as an
optional property, but will give a warning when used.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cleanups to i2c-cores, no change in logic, changes are:
* Move i2c-ocores device tree documentation from source file to
Documentation/devicetree/bindings/i2c/i2c-ocores.txt.
* Add \n to dev_warn and dev_err messages where missing
* Minor updates to the text and formatting fixes.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
As git history indicates, the driver predates the git era and is heavily
used and worked on since. Not EXPERIMENTAL anymore.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Florian Fainelli <ffainelli@freebox.fr>
There's no point in using _sync() as we don't really care if the suspend
has completed immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
