* git://git.infradead.org/iommu-2.6:
intel-iommu: Don't use identity mapping for PCI devices behind bridges
intel-iommu: Use iommu_should_identity_map() at startup time too.
intel-iommu: No mapping for non-PCI devices
intel-iommu: Restore DMAR_BROKEN_GFX_WA option for broken graphics drivers
intel-iommu: Add iommu_should_identity_map() function
intel-iommu: Fix reattaching of devices to identity mapping domain
intel-iommu: Don't set identity mapping for bypassed graphics devices
intel-iommu: Fix dma vs. mm page confusion with aligned_nrpages()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: add support for disks >2 TB (and 16 bytes long CDBs)
firewire: sbp2: add support for disks >2 TB (and 16 bytes long CDBs)
firewire: core: do not DMA-map stack addresses
This way they'll be properly initialized early enough for users that may
touch them before the framebuffer has been registered.
Drivers that allocate their fb_info structure some other way (like
matrocfb's broken static allocation) need to be fixed up appropriately.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These warnings were observed on MIPS32 using 2.6.31-rc1 and gcc-4.2.0:
mm/page_alloc.c: In function 'alloc_pages_exact':
mm/page_alloc.c:1986: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast
drivers/usb/mon/mon_bin.c: In function 'mon_alloc_buff':
drivers/usb/mon/mon_bin.c:1264: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast
[akpm@linux-foundation.org: fix kernel/perf_counter.c too]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When i2c_smbus_read_byte_data fails in ds1374_work, we forgot to unlock
the held lock. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in the VLYNQ bus driver Kconfig which prevented to turn on
VLYNQ bus debugging.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in the vlynq bus driver which was missing the CONFIG_ prefix to
turn on debugging code.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove redundant call to the sisfb_get_fix() before sis frambuffer is
registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059 " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet a écrit :
> Ingo Molnar a écrit :
>>> The following changes since commit 5298976562:
>>> Linus Torvalds (1):
>>> Merge git://git.kernel.org/.../davem/net-2.6
>>>
>>> are available in the git repository at:
>>>
>>> master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git master
>> Hm, something in this lot quickly wrecked networking here - see the
>> tx timeout dump below. It starts with:
>>
>> [ 351.004596] WARNING: at net/sched/sch_generic.c:246 dev_watchdog+0x10b/0x19c()
>> [ 351.011815] Hardware name: System Product Name
>> [ 351.016220] NETDEV WATCHDOG: eth0 (forcedeth): transmit queue 0 timed out
>>
>> Config attached. Unfortunately i've got no time to do bisection
>> today.
>
>
>
> forcedeth might have a problem, in its netif_wake_queue() logic, but
> I could not see why a recent patch could make this problem visible now.
>
> CPU0/1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> is not a new cpu either :)
>
> forcedeth uses an internal tx_stop without appropriate barrier.
>
> Could you try following patch ?
>
> (random guess as I dont have much time right now)
We might have a race in napi_schedule(), leaving interrupts disabled forever.
I cannot test this patch, I dont have the hardware...
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call resource_size(res) returns res->end - res->start + 1 and thus the
second change is semantics-preserving. res_size is then used as the second
argument of a call to request_mem_region, and the memory allocated by this
call appears to be the same as what is released in the two calls to
release_mem_region. So the size argument for those calls should be
resource_size(size) as well. Alternatively, in the second call to
release_mem_region, the second argument could be res_size, as that variable
has already been initialized at the point of this call.
The problem was found using the following semantic patch:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
@@
struct resource *res;
@@
- res->end - res->start
+ BAD(resource_size(res))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
add new id (RIOS System PC CARD3 ETHERNET).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch properly defines the maximum values for rx/tx coalescing timeouts.
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem reported by Flavio Leitner <fleitner@redhat.com>:
When setting rx/tx coalescing timeout to the values less than 12 traffic was
stopped.
The FW supports coalescing in 12us granularity, and so value of less then 12
should be interpreted as disabling coalescing
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is currently possible for an asynchronous device unregister
to cause the same tun device to be unregistered twice. This
is because the unregister in tun_chr_close only checks whether
__tun_get(tfile) != NULL. This however has nothing to do with
whether the device has already been unregistered. All it tells
you is whether __tun_detach has been called.
This patch fixes this by using the most obvious thing to test
whether the device has been unregistered.
It also moves __tun_detach outside of rtnl_unlock since nothing
that it does requires that lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one path with omitted unlock in si470x_fops_release. Fix that.
Cc: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is one omitted unlock in em28xx_usb_probe. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Discovered the bug that were limiting the output format to just RGB565.
Now, it is possible to output image at Bayer format (the original one,
as generated by Silvercrest sensor, and two others), and also on YUY.
Adds Bayer formats also to the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AMBA device resources were being reported as:
10004000-10004fff : <BAD>
This is because dev_name() was returning NULL prior to device_register.
Ensure that the struct device is properly initialized, and the name is
set before adding it to the device tree.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Webcams have different constraints than other v4l devices. This patch
makes the format ioctls to behave better. It also fixes a bug at open()
handler, that were always reseting resolution to the maximum available
one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the code so that the zl10353 version of the Terratec Cinergy T XS USB
starts working again. This includes fixing what must have been a typo in the
GPIO definition for the digital side of the board, and setting of the
disable_i2c_gate_ctrl property for the zl10353 config, so that the i2c bus
doesn't get wedged the first time something tries to close the gate.
Also, add a printk() making clear that the mt352 version still isn't
supported. This issue is still being actively debugged, but in the meantime
at least the dmesg output will show a very clear error...
Thanks to Jelle de Jong for providing sample hardware to test with.
Thanks to Simon Kenyon for testing various patches and providing SSH access to
his environment so I could debug with access to a valid signal source.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Cc: Simon Kenyon <simon@koala.ie>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add suppport for the teste RGB565 format (16 bits/pixel).
Currently, webcam support works only at RGB565, at 640x480.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.
It needs a few different initializations than a normal em28xx device.
Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original driver for Silvercrest cameras were using some values that
are different from what datasheet says. As result, it was taken very
less snapshots per second than expected.
A test with the datasheet values showed that they work fine and give a
better frame rate. So, let's stick with datasheet values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of working with a table of precalculated values, fill them with
the proper values. Also, adds format functions that allow changing the
resolution, by cropping the image to the center of the sensor.
While here, move the sensor version check to the probe routine, to
indicate to the caller if the sensor is not supported by this driver.
Also, fixes a stupid bug where we're using &buffer[] instead of
buffer[].
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds driver for mt9v011 based on its datasheet, available at:
http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf
The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add FIXME comment to indicate that the set_frontend override is a
temporary hack. This will be done a better way in the next kernel.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use separate RF input spigots for Antennae and Cable.
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.
There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).
Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.
Tested-by: Steve Firth <firth650@btinternet.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: Terry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If soc_camera_init_user_formats() fails in soc_camera_probe(), we have to call
client's .remove() method to unregister the video device.
Reported-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The supported formats count must be set to 0 after debug output
right before the second pass.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the image seq. number handling from I/O level to the scanning
lever, where it really belongs to. Move the @image_seq_set variable
to the @struct ubi_scan_info structure, which exists only during
scanning.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
An image sequence number is added to the UBI erase-counter header
to be able determine if the root file system contains a mixture
of old and new images (because the flashing failed to complete).
A change to nolo is also needed for this to take effect.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'paranoid_check_empty()' is bogus because, which is easilly
seen on NOR flash, which has long erase cycles, and which may
easilly end-up with half-erased eraseblocks. In this case the
paranoid check fails. I is just wrong to assume that PEBs which
do not have EC headers always contain all 0xFF. Such assumption
should not be made on the I/O level, which is quite low.
Thus, just kill the check.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds code which makes sure eraseblocks contain all 0xFF
bytes before starting using them. The verification is done only when
debugging checks are enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
precalculate_bars() improved vivi performance. However, it assumed that
always before streaming, the driver would call VIDIOC_S_STD. This is not
an API requirement, and the testing apps don't do that.
Due to that, a regression were caused by the patch that added it.
This patch moves the precalculate_bars to the proper place of the code,
calling it at buffer_prepare() callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our current strategy for pass-through mode is to put all devices into
the 1:1 domain at startup (which is before we know what their dma_mask
will be), and only _later_ take them out of that domain, if it turns out
that they really can't address all of memory.
However, when there are a bunch of PCI devices behind a bridge, they all
end up with the same source-id on their DMA transactions, and hence in
the same IOMMU domain. This means that we _can't_ easily move them from
the 1:1 domain into their own domain at runtime, because there might be DMA
in-flight from their siblings.
So we have to adjust our pass-through strategy: For PCI devices not on
the root bus, and for the bridges which will take responsibility for
their transactions, we have to start up _out_ of the 1:1 domain, just in
case.
This fixes the BUG() we see when we have 32-bit-capable devices behind a
PCI-PCI bridge, and use the software identity mapping.
It does mean that we might end up using 'normal' mapping mode for some
devices which could actually live with the faster 1:1 mapping -- but
this is only for PCI devices behind bridges, which presumably aren't the
devices for which people are most concerned about performance.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
At boot time, the dma_mask won't have been set on any devices, so we
assume that all devices will be 64-bit capable (and thus get a 1:1 map).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 537a1bf059 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:
Badness at kernel/mutex.c:207
Pid : 1, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc1-00284-g529ba0d-dirty #2273)
PC is at __mutex_lock_slowpath+0x72/0x1bc
PR is at __mutex_lock_slowpath+0x66/0x1bc
...
matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
MIPS: Reorganize Cavium OCTEON PCI support.
Update Yoichi Yuasa's e-mail address
MIPS: Allow suspend and hibernation again on uniprocessor kernels.
MIPS: 64-bit: Fix o32 core dump
MIPS: BC47xx: Fix SSB irq setup
MIPS: CMP: Update sync-r4k for current kernel
MIPS: CMP: Move gcmp_probe to before the SMP ops
MIPS: CMP: activate CMP support
MIPS: CMP: Extend IPI handling to CPU number
MIPS: CMP: Extend the GIC IPI interrupts beyond 32
MIPS: Define __arch_swab64 for all mips r2 cpus
MIPS: Update VR41xx GPIO driver to use gpiolib
MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
MIPS: Malta: Remove unnecessary function prototypes
MIPS: MT: Remove unnecessary semicolons
MIPS: Add support for Texas Instruments AR7 System-on-a-Chip
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't merge requests of different failfast settings
cciss: Ignore stale commands after reboot
The sh7724 processor has two on-chip r8a66597 blocks, so add
it to the list of processors for SUPERH_ON_CHIP_R8A66597.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This should fix kernel.org bug #11821, where the dcdbas driver makes up
a platform device and then uses dma_alloc_coherent() on it, in an
attempt to get memory < 4GiB.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We need to give people a little more time to fix the broken drivers.
Re-introduce this, but tied in properly with the 'iommu=pt' support this
time. Change the config option name and make it default to 'no' too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do this twice, and it's about to get more complicated. This makes the
code slightly clearer about what it's doing, too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we reattach a device to the si_domain (because it's been removed
from a VM), we weren't calling domain_context_mapping() to actually tell
the hardware about that.
We should really put the call to domain_context_mapping() into
domain_add_dev_info() -- we never call the latter without also doing the
former, and we can keep the error paths simple that way. But that's a
cleanup which can wait for 2.6.32 now.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We should check iommu_dummy() _first_, because that means it's attached
to an iommu that we've just disabled completely. At the moment, we might
try to put the device into the identity mapping domain.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The aligned_nrpages() function rounds up to the next VM page, but
returns its result as a number of DMA pages.
Purely theoretical except on IA64, which doesn't boot with VT-d right
now anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Occasionally we may see an interrupt without an event in the eq.
In intx, we currently see the event queue and return IRQ_NONE causing
a the irq to be disabled ("no one cared".) Instead, read the CEV_ISR
reg to check the existence of the interrupt.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs may require two reads of the PHY_STATUS register to determine the
link status. If the PHY is being accessed by another thread it is possible
the first read could timeout and fail. In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was accessing register bits for features on parts that do
not support that feature. This could cause problems in the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently. Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing. Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround. Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().
I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module. So we
only check if that is the case.
This problem also shows up on Copper devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.
- mdio45_probe call was always failing due to mdio.prtad not being
set. The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0. This will allow us to set the phy_id
and phy.type correctly now.
- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.
- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some usage was only sizing a pointer rather than the data type.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set/clear the mac address register when the link goes up/down
respectively. Without this both ports of a 2-port device can end up
with the same mac address in a bonding scenario.
The new ql_link_on() and ql_link_off() will also be used in handling
certain firmware events.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addes functionality to set/clear the MAC address in the hardware
when the link goes up/down.
The MAC address register is persistent across function resets. In
bonding the same address can bounce from one port to the other. This
can cause packets to be delivered to the wrong port.
This patch clears the MAC address in the hardware when the link is down
and sets it when the link comes up.
It was found that pulling/pushing the cable from one port to another
causes the same MAC address to be in both ports.
The next patch in this series will use this functionality as well.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller will free acquired resouces if a failure occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were turning on the carrier without verifying the link was up.
This adds link up to the link initialize check before turning carrier
on.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not clearing the routing bits can cause frames to erroneously get routed to
management processor.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware semaphore covers the configuration register as well as the
ICB registers. The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded. Currently we were
only protecting the ICB regs. This changes expands to cover the config
register as well.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing an unexpected shutdown like kexec the cciss
firmware might still have some commands in flight, which
it is trying to complete.
The driver is doing it's best on resetting the HBA,
but sadly there's a firmware issue causing the firmware
_not_ to abort or drop old commands.
So the firmware will send us commands which we haven't
accounted for, causing the driver to panic.
With this patch we're just ignoring these commands as
there is nothing we could be doing with them anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
The current ssb irq setup in ssb_mipscore_init has the problem that it
configures some device on some irq without checking that the irq is not
taken by an other device.
For example in my case PCI host is on irq 0 and IPSEC on irq 3.
The current code:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host
But now IPSEC irq is not routed anymore to the mips code and dev->irq is
wrong. This causes a problem described in [1].
This patch tries to solve the problem by making set_irq configure the
device we want to take the irq on the shared irq0. The previous example
becomes:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host:
- irq 3 is already taken by IPSEC. do a set_irq 3->0 on IPSEC
I also added some code to print the irq configuration after irq setup to
allow easier debugging. And I add extra checking in ssb_mips_irq to report
device without irq or device with not routed irq.
[1] http://www.danm.de/files/src/bcm5365p/REPORTED_DEVICES
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch updates the receive error code for muxed
interrupts in the sh-sci driver.
Receive error interrupts may be generated by the hardware
if RE or REIE bits in SCSCR are set. Update the muxed
interrupt handling code to acknowledge error interrupts
if RE or REIE is set, instead of only acknowledging if
REIE is set.
Without this patch error interrupts may be generated but
never acked resulting in a "nobody cared" crash.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Usage of parport_pc_probe_port was changed in 28783eb52
(parport: Fix various uses of parport_pc).
It introduced this build error:
drivers/parisc/superio.c: In function 'superio_parport_init':
drivers/parisc/superio.c:437: error: too few arguments to function
'parport_pc_probe_port'
Fix it.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
We weren't marking the resources as memory resources, so they weren't
being found by pci_claim_resource().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
gcc 4.4 warns about:
drivers/parisc/lba_pci.c: In function 'lba_pat_resources':
drivers/parisc/lba_pci.c:1099: warning: the frame size of 8280 bytes is larger than 4096 bytes
The problem is we declare two large structures on the stack. They don't need
to be on the stack since they are only used during LBA initialization (which
is serialized). Moving to be "static".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Alex Chiang asked me why PARISC was calling pci_bus_add_devices()
and pci_bus_assign_resources() in the opposite order from everyone else.
No reason and I couldn't see any data dependency.
Patch below applies cleanly to 2.6.30-rc2.
Later, I suspected the code worked only because no drivers would be
loaded/ready until much later in the system initialization sequence.
Tested "LBA" code on J6000 (32-bit) and A500 (64-bit SMP) with 2.6.30-rc2.
Not tested with any Dino controllers.
Not tested with PCI-PCI Bridge (TBD).
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix this build error when CONFIG_PROC_FS is not set:
drivers/parisc/ccio-dma.c:1574: error: 'ccio_proc_info_fops' undeclared
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix this build error when CONFIG_STI_CONSOLE is not set
drivers/video/stifb.c:1337: undefined reference to `sti_get_rom'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] cxgb3i: fix connection error when vlan is enabled
[SCSI] FC transport: Locking fix for common-code FC pass-through patch
[SCSI] zalon: fix oops on attach failure
[SCSI] fnic: use DMA_BIT_MASK(nn) instead of deprecated DMA_nnBIT_MASK
[SCSI] fnic: remove redundant BUG_ONs and fix checks on unsigned
[SCSI] ibmvscsi: Fix module load hang
* git://git.infradead.org/iommu-2.6: (38 commits)
intel-iommu: Don't keep freeing page zero in dma_pte_free_pagetable()
intel-iommu: Introduce first_pte_in_page() to simplify PTE-setting loops
intel-iommu: Use cmpxchg64_local() for setting PTEs
intel-iommu: Warn about unmatched unmap requests
intel-iommu: Kill superfluous mapping_lock
intel-iommu: Ensure that PTE writes are 64-bit atomic, even on i386
intel-iommu: Make iommu=pt work on i386 too
intel-iommu: Performance improvement for dma_pte_free_pagetable()
intel-iommu: Don't free too much in dma_pte_free_pagetable()
intel-iommu: dump mappings but don't die on pte already set
intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()
intel-iommu: Introduce domain_sg_mapping() to speed up intel_map_sg()
intel-iommu: Simplify __intel_alloc_iova()
intel-iommu: Performance improvement for domain_pfn_mapping()
intel-iommu: Performance improvement for dma_pte_clear_range()
intel-iommu: Clean up iommu_domain_identity_map()
intel-iommu: Remove last use of PHYSICAL_PAGE_MASK, for reserving PCI BARs
intel-iommu: Make iommu_flush_iotlb_psi() take pfn as argument
intel-iommu: Change aligned_size() to aligned_nrpages()
intel-iommu: Clean up intel_map_sg(), remove domain_page_mapping()
...
For some reason, the DP clocks were based off a 100MHz reference instead of
the standard 96MHz reference. This caused some DP monitors to fail to lock
to the signal.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING. Add a call to phy_read_status() to
update the link before entering PHY_RUNNING. If the link is not up at
this point, enter the PHY_NOLINK state instead.
Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing. Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict firmware reset to following cases -
o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.
This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.
Also fix a infinite loop when cut-thru file firmware is
invalid.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop a sanity check which doesn't serve any useful purpose anymore.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
ISDN connection setup failed if the "connection active" and
"B channel up" messages from the device arrived in a different
order than expected. Modify the state machine to accept them in
any order.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Check dma_pte_present() and only free the page if there _is_ one.
Kind of surprising that there was no warning about this.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On Wed, 2009-07-01 at 16:59 -0700, Linus Torvalds wrote:
> I also _really_ hate how you do
>
> (unsigned long)pte >> VTD_PAGE_SHIFT ==
> (unsigned long)first_pte >> VTD_PAGE_SHIFT
Kill this, in favour of just looking to see if the incremented pte
pointer has 'wrapped' onto the next page. Which means we have to check
it _after_ incrementing it, not before.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert many printk calls to DRM_DEBUG calls to reduce kernel log noise
for normal activities. Switch other printk calls to DRM_ERROR or DRM_INFO.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We are seeing compilation failures on i386 in some environments due
to an undefined reference as below:
ERROR: "__udivdi3" [drivers/gpu/drm/i915/i915.ko] undefined!
This is generated due to a raw 64 bit divide in the i915 driver. Fix up
this raw divide.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For many purposes, including interrupt-swizzling, devices with ARI
enabled behave as if they have one device (number 0) and 256 functions.
This probably hasn't bitten us in practice because all ARI devices I've
seen are also IOV devices, and IOV devices are required to use MSI.
This isn't guaranteed, and there are legitimate reasons to use ARI
without IOV, and hence potentially use pin-based interrupts.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This would have found the bug in i386 pci_unmap_addr() a long time ago.
We shouldn't just silently return without doing anything.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: LCDC dcache flush for deferred io
sh: Fix compiler error and include the definition of IS_ERR_VALUE
sh: re-add LCDC fbdev support to the Migo-R defconfig
sh: fix se7724 ceu names
sh: ms7724se: Enable sh_eth in defconfig.
arch/sh/boards/mach-se/7206/io.c: Remove unnecessary semicolons
sh: ms7724se: Add sh_eth support
nommu: provide follow_pfn().
sh: Kill off unused DEBUG_BOOTMEM symbol.
perf_counter tools: add cpu_relax()/rmb() definitions for sh.
sh64: Hook up page fault events for software perf counters.
sh: Hook up page fault events for software perf counters.
sh: make set_perf_counter_pending() static inline.
clocksource: sh_tmu: Make undefined TCOR behaviour less undefined.
Currently we implemented basic sdvo lvds function,
But except for sdvo lvds fixed mode, we can not switch
to other modes, otherwise display get black. The patch
handle three operations to enable sdvo lvds. At first
duplicate sdvo fixed mode for adjustment, then according
to fixed mode line valid all modes, at last adjust input
mode to fit our requirement.
Acked by Li Peng <peng.li@linux.intel.com>
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since we're using cmpxchg64() anyway (because that's the only way to do
an atomic 64-bit store on i386), we might as well ditch the extra
locking and just use cmpxchg64() to ensure that we don't add the page
twice.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since writenotify on uncached vmas is unsupported in 2.6.31,
live with cached framebuffer memory in the deferred io
case for now and flush the dcache before forcing refresh.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus damm <damm@igel.co.jp>
* git://git.infradead.org/mtd-2.6:
mtd: nand: fix build failure and incorrect return from omap_wait()
mtd: Use BLOCK_NIL consistently in NFTL/INFTL
mtd: m25p80 timeout too short for worst-case m25p16 devices
mtd: atmel_nand: Fix typo s/parititions/partitions/
mtd: cmdlineparts: Use 64-bit format when printing a debug message.
mtd: maps: Remove BUS_ID_SIZE from integrator_flash
jffs2: fix another potential leak on error path in scan.c
All 8xx class chips have the 66/48 split, not just 855.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes kernel.org bug #13584. The IOVA code attempted to optimise
the insertion of new ranges into the rbtree, with the unfortunate result
that some ranges just didn't get inserted into the tree at all. Then
those ranges would be handed out more than once, and things kind of go
downhill from there.
Introduced after 2.6.25 by ddf02886cb
("PCI: iova RB tree setup tweak").
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: mark gross <mgross@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch from jbarnes and myself adds FIFO watermark control to the
driver. This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.
It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables error detection by enabling several types of error
interrupts. When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.). The new
record is then available from sysfs. The current code will also dump
the error state to the system log.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: remove redundant check for NULL cfqq in cfq_set_request()
blocK: Restore barrier support for md and probably other virtual devices.
block: get rid of queue-private command filter
block: Create bip slabs with embedded integrity vectors
cfq-iosched: get rid of the need for __GFP_NOFAIL in cfq_find_alloc_queue()
cfq-iosched: move cfqq initialization out of cfq_find_alloc_queue()
Trivial typo fixes in Documentation/block/data-integrity.txt.
* 'for-linus' of git://neil.brown.name/md:
md: use interruptible wait when duration is controlled by userspace.
md/raid5: suspend shouldn't affect read requests.
md: tidy up error paths in md_alloc
md: fix error path when duplicate name is found on md device creation.
md: avoid dereferencing NULL pointer when accessing suspend_* sysfs attributes.
md: Use new topology calls to indicate alignment and I/O sizes
The init_IRQ() function is now called with slab allocator initialized.
Therefore, we must not use the bootmem allocator in xen_init_IRQ().
Fixes the following boot-time warning:
------------[ cut here ]------------
WARNING: at mm/bootmem.c:535 alloc_arch_preferred_bootmem+0x27/0x45()
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.30 #1
Call Trace:
[<ffffffff8102d6e3>] ? warn_slowpath_common+0x73/0xb0
[<ffffffff810210d9>] ? pvclock_clocksource_read+0x49/0x90
[<ffffffff812e522f>] ? alloc_arch_preferred_bootmem+0x27/0x45
[<ffffffff812e5761>] ? ___alloc_bootmem_nopanic+0x39/0xc9
[<ffffffff812e57fa>] ? ___alloc_bootmem+0x9/0x2f
[<ffffffff812e9e21>] ? xen_init_IRQ+0x25/0x61
[<ffffffff812d69ee>] ? start_kernel+0x1b5/0x29e
---[ end trace 4eaa2a86a8e2da22 ]---
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: lists@nerdbynature.de
Cc: jeremy.fitzhardinge@citrix.com
LKML-Reference: <1246438278.22417.28.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The initial patches to support this through sysfs export were broken
and have been if 0'ed out in any release. So lets just kill the code
and reclaim some space in struct request_queue, if anyone would later
like to fixup the sysfs bits, the git history can easily restore
the removed bits.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch restores stacking ability to the block layer integrity
infrastructure by creating a set of dedicated bip slabs. Each bip slab
has an embedded bio_vec array at the end. This cuts down on memory
allocations and also simplifies the code compared to the original bvec
version. Only the largest bip slab is backed by a mempool. The pool is
contained in the bio_set so stacking drivers can ensure forward
progress.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
User space can set various limits on an md array so that resync waits
when it gets to a certain point, or so that I/O is blocked for a short
while.
When md is waiting against one of these limit, it should use an
interruptible wait so as not to add to the load average, and so are
not to trigger a warning if the wait goes on for too long.
Signed-off-by: NeilBrown <neilb@suse.de>
md allows write to regions on an array to be suspended temporarily.
This allows user-space to participate is aspects of reshape.
In particular, data can be copied with not risk of a race.
We should not be blocking read requests though, so don't.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
on permanent failure
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is not
checked in many of the network drivers.
This patch fixes the omission in the e1000e driver.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is
not checked in many of the network drivers.
The patch fixes the omission in the e1000 driver.
Based on Mike Mason's similar patch for e1000e.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
CC: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into
also fix unmap related bug where ->dma was not being cleared
after unmap
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses three WARN_ON statements from DMA-API debug code
ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.
found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.
in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single
and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a wide range of log messages for the same sort of SFP
failure. This patch makes them all more similar and less
confusing along with converting them to dev_err.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the recent bug in md_alloc showed, having a single exit path for
unlocking and putting is a good idea. So restructure md_alloc to have
a single mutex_unlock and mddev_put, and use gotos where necessary.
Found-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When an md device is created by name (rather than number) we need to
check that the name is not already in use. If this check finds a
duplicate, we return an error without dropping the lock or freeing
the newly create mddev.
This patch fixes that.
Cc: stable@kernel.org
Found-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm table: fix blk_stack_limits arg to use bytes not sectors
dm exception store: really fix type lookup
A crappy macro prevents us unlocking on a fail path.
Expand the macro and unlock appropriatelly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure we do not actually request the RTC IRQ until the device driver
is fully ready to handle and process any interrupt. This way a spurious
interrupt won't crash the system (which may happen if the bootloader was
poking the RTC right before booting Linux).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Block writes require 64 byte alignment. Since block writes could be used
with SGRAM or WRAM also refine the memory type detection to check for
either type before deciding to use the 64 byte alignment.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
