Non-broadcast packets larger than MTU are fragmented and sent with
an encapsulating header. Up to 16 fragments are supported, which are
sent in reverse order on the wire to allow minimal memory copying when
creating fragments.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.
Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.
batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().
fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.
BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
In case of a VLAN tagged frame the ethhdr pointer is
moved forward by 4 bytes so that the offset of h_proto
in struct ethhdr matches the real
h_vlan_encapsulated_proto address in the skb. While this
trickery is correct it makes the code harder to understand
and may lead to bugs in case of re-use of ethhdr for other
purposes.
This patch introduces a proto variable to make things
cleaner and easier to understand.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batadv_tt_global_entry_free_ref uses call_rcu to schedule a
function which will only free the global entry itself.
For this reason call_rcu is useless and kfree_rcu can be
used to simplify the code.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batadv_tt_global_add_orig is neither used nor implemented
anymore, therefore it is possible to remove its declaration
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batadv_tt_global_add is not used anymore outside of the TT
code thanks to the TVLV implementation. It can therefore be
declared as static
Last user has been removed by 3de4e64df0f1326db7cc0ef25f5af8522850252d
("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
Moreover make it return bool since its result can be either 0 or 1.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Adding host information for record route is only required for ICMP
requests and replys, and should not be added to just any (future?)
packet type.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
1) We need to take a timestamp only for skb that should be cloned.
Other skbs are not in write queue and no rtt estimation is done on them.
2) the unlikely() hint is wrong for receivers (they send pure ACK)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: MF Nowlan <fitz@cs.yale.edu>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- update emails for A. Quartulli and M. Lindner in MAINTAINERS
- switch to the next on-the-wire protocol version
- introduce the T(ype) V(ersion) L(ength) V(alue) framework
- adjust the existing components to make them use the new TVLV code
- make the TT component use CRC32 instead of CRC16
- totally remove the VIS functionality (has been moved to userspace)
- reorder packet types and flags
- add static checks on packet format
- remove __packed from batadv_ogm_packet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJSVa1BAAoJEADl0hg6qKeOiZkP/iD8Gehkb+jII3J1AE4+TdaW
X5XzB40A6bRr/RhiqqFXA6FhjLPCwPlaYwo+FL9QC9fIbV6Drofd8B4Vxvp8daQI
A5ZTzA7GFJhUkzM4vvw5eyF5848OYGITAJh5kSkiYiFSC6x9X9UFrG1EBBX7ikGd
7MXCjNa5GXaO7BsSnSbGuuMYw6CuZxwwxUZ3F/fG031yTlRqz88TiBpOGCZXSM5J
eYOf68byDPPsRvj/RgpmYTt7MzWnAgp9gJotp5Owuqpb3kvZC6SkA8uj4O2f29rn
nmQ+1q5onjHpfqukezPOIx9HEKo2XCq3qbFiW74dyNi+EQlYJ6RAGyRBkTTl4hse
cTOeWENANoFco/SPiOi1PjGrytuflAiIegwkVugAvnmYlbsVIi6MXV+BGo/ARybv
RwPBFULCaxO5HNkYz6elcu8cwFY9s3PROEdMVpRj+iNTeQq3ZQHj+QfPsHdedkAz
mkHqiZQo/pgBeWd+KiN98YJtQ4nPV1Qi+yGiayc3hmsk5fIABaOHxP3NV0NrTeOO
PYKWFcKfdLgtvrfcOXbcWpPz0d8SUkyF8zjlzIscXlpJVWK1sOw8oEER3IrDgzDy
PmzHkEL+qfDh4I5hEPOIEXxzPw/E4b+G3WI34bUN/4chGSmJdo6yyaC6XcXe7r9g
AsxmABE84uT2npNSOSkN
=YQD5
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- update emails for A. Quartulli and M. Lindner in MAINTAINERS
- switch to the next on-the-wire protocol version
- introduce the T(ype) V(ersion) L(ength) V(alue) framework
- adjust the existing components to make them use the new TVLV code
- make the TT component use CRC32 instead of CRC16
- totally remove the VIS functionality (has been moved to userspace)
- reorder packet types and flags
- add static checks on packet format
- remove __packed from batadv_ogm_packet
Jeff Kirsher says:
====================
This series contains updates to i40e only.
Alex provides the majority of the patches against i40e, where he does
cleanup of the Tx and RX queues and to align the code with the known
good Tx/Rx queue code in the ixgbe driver.
Anjali provides an i40e patch to update link events to not print to
the log until the device is administratively up.
Catherine provides a patch to update the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 634fb979e8 ("inet: includes a sock_common in request_sock")
I forgot that the two ports in sock_common do not have same byte order :
skc_dport is __be16 (network order), but skc_num is __u16 (host order)
So sparse complains because ir_loc_port (mapped into skc_num) is
considered as __u16 while it should be __be16
Let rename ir_loc_port to ireq->ir_num (analogy with inet->inet_num),
and perform appropriate htons/ntohs conversions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver uses different RSSI threshold
and VGC adjustment values for the RT3572 and
RT3593 chipsets.
Update the rt2800_link_tuner function to use the
same values. Also change the comment in the function
to make it more generic.
References:
RT35xx_ChipAGCAdjust function in chips/rt35xx.c
RSSI_FOR_MID_LOW_SENSIBILITY constant in include/chip/rtmp_phy.h
RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 3d81535ea5
(rt2800: 5592: add chip specific vgc calculations)
the rt2800_link_tuner function has been modified to
adjust VGC level for the RT5592 chipset.
On the RT5592 chipset, the VGC level must be adjusted
only if rssi is greater than -65. However the current
code adjusts the VGC value by 0x10 regardless of the
actual chipset if the rssi value is between -80 and
-65.
Fix the broken behaviour by reordering the if-else
statements.
Cc: stable@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the local MOVING_AVERAGE implementation, and use
the generic EWMA functions instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800_config_channel_rf3xxx(), there's no need to toggle
RF R30 bit 7 twice.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pausing queue on flush make no sense since txdone procedure un-pause
queue. Before flush procedure we have to assure queue is stopped,
i.e. on receive path h/w RX is disabled, on transmit path queue is
disabled in mac80211. That conditions are true except one function:
rt2x00usb_watchdog_tx_dma(), so add stop/start queue there.
Note stop/start queue can be racy if we do this from multiple paths,
but currently we stop TX queues only on rt2x00lib_disable_radio(),
which also stop/sync watchdog, hance we have no race condition.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 driver uses 0x22 as a default VGC value
in VGC adjustment for the RT3572 chipset. In the
Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022 driver,
this value is only used for initialization. During
VGC adjustment, the reference driver uses different
values.
Update the 'rt2800_get_default_vgc' function to
synchronize the values with the reference driver.
Also add the missing AGC initialization code into
the 'rt2800_config_channel' function.
References:
RT35xx_SetAGCInitValue in chip/rt35xx.c
RT35xx_ChipAGCAdjust in chip/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver, programming of the 'BBP 66' register
on the RT3572 and RT3593 chipsets must be done via the
'rt2800_bbp_write_with_rx_chain' function. This ensures
that value is correclty set for all RX chains.
References:
RT35xx_ChipAGCAdjust and RT35xx_SetAGCInitValue functions
in chips/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rt2800_get_default_vgc function to use the same VGC
values that the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference
driver uses.
References:
RT35xx_ChipAGCAdjust in chips/rt35xx.c
RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TXPOWER_DELTA field of the regular EEPROM
stores the TX power compensation value for HT40.
The extended EEPROM has no such field, it stores
separate TX power values for HT20 and for HT40.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comments are indicating that the TXMIXER_GAIN_BG
and TXMIXED_GAIN_A entries are overlapping with the
RSSI_BG2 and RSSI_A2 entries in the extended EEPROM
map. This is not correct, because the upper byte of
the RSSI_BG2 and RSSI_A2 entries are reserved. There
are no TX mixer gain values are stored at all in the
extended EEPROM.
Remove the initialization of these entries from the
extended EEPROM map to reflect this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some BCM4313 out there with a PCI id of 0x4313. These devices
are missing a sprom and are only used on routers or other embedded
devices. We found one connected to a BCM63XX SoC.
This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This PCI id is used by some BCM4313 cards without a sprom. I have seen
such a card on a router connected to some BCM63XX SoC via PCIe. There
are cards out there with the same PCI id and a BCM4311, which is a pre
ieee80211n chip only supporting ieee80211a, these are still not
supported by b43 and not detected by ssb.
This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma currently only supports PCIe cards and no PCI cards, reject them
if we find them. I have never heard of any PCI card using the AI bus
(bcma), all of them are using ssb instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TI firmwares are located under ti-connectivity
directory. Update path to make sure driver can
find and load firmware blob.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently driver name is wrong. PCI device address is visible at
/proc/interrupts instead of the name:
43: 124 0 0 0 PCI-MSI-edge rtsx_pci
44: 384 0 0 0 PCI-MSI-edge snd_hda_intel
45: 25096 0 0 0 PCI-MSI-edge 0000:01:00.0
^^^^^^^^^^^^
So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME
and good for that, so pass it.
Handler names will be "rt2500pci", "rt2500pci" etc.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: Ivo van Doorn <IvDoorn@gmail.com>
CC: Gertjan van Wingerde <gwingerde@gmail.com>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
CC: linux-wireless@vger.kernel.org
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So
far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS
Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx
A lot people made a contribution to this driver. Here is the list in
alphabetical order:
Eugene Krasnikov <k.eugene.e@gmail.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Olof Johansson <dev@skyshaper.net>
Pontus Fuchs <pontus.fuchs@gmail.com>
Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variables cancel_scan_cmd, enable_data, hs_activate and valid are
only assigned the values true and false. Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds IPv6 support for IPsec virtual tunnel interfaces
(vti). IPsec virtual tunnel interfaces provide a routable interface
for IPsec tunnel endpoints.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Update the version number of the driver.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change brings support for 64 bit netstats to the driver. Previously
the stats were 64 bit but highly racy due to the fact that 64 bit
transactions are not atomic on 32 bit systems. This change makes is so
that the 64 bit byte and packet stats are reliable on all architectures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate the queue pairs individually instead of as a group. This
allows for much easier queue management as it is possible to dynamically
resize the queues without having to free and allocate the entire block.
Ease statistic collection by treating Tx/Rx queue pairs as a single
unit. Each pair is allocated together and starts with a Tx queue and
ends with an Rx queue. By ordering them this way it is possible to know
the Rx offset based on a pointer to the Tx queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This replaces the ring container array with a linked list. The idea is
to make the logic much easier to deal with since this will allow us to
call a simple helper function from the q_vectors to go through the
entire list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate the q_vectors individually. The advantage to this is that it
allows for easier freeing and allocation. In addition it makes it so
that we could do node specific allocations at some point in the future.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This makes it so that the Tx and Rx byte and packet counts are
separated from the rest of the statistics. This allows for better
isolation of these stats when we move them into the 64 bit statistics.
Simplify things by re-ordering how the stats display in ethtool.
Instead of displaying all of the Tx queues as a block, followed by all
the Rx queues, the new order is Tx[0], Rx[0], Tx[1], Rx[1], ..., Tx[n],
Rx[n]. This reduces the loops and cleans up the display for testing
purposes since it is very easy to verify if flow director is doing the
right thing as the Tx and Rx queue pair are shown in pairs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop Tx flag and TXSW which is tested but never set.
As a result of this change we can drop a complicated check that always
resulted in the final result of i40e_tx_csum being equal to the
CHECKSUM_PARTIAL value. As such we can replace the entire function call
with just a check for skb->summed == CHECKSUM_PARTIAL.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sync the fast path for i40e_tx_map and i40e_clean_tx_irq so that they
are similar to igb and ixgbe.
- Only update the Tx descriptor ring in tx_map
- Make skb mapping always on the first buffer in the chain
- Drop the use of MAPPED_AS_PAGE Tx flag
- Only store flags on the first buffer_info structure
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid directly incrementing next_to_use for multiple reasons. The main
reason being that if we directly increment it then it can attain a state
where it is equal to the ring count. Technically this is a state it
should not be able to reach but the way this is written it now can.
This patch pulls the value off into a register and then increments it
and writes back either the value or 0 depending on if the value is equal
to the ring count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- drop the mapped_as_page u8 from the Tx buffer info as it was unused
- use the DMA unmap accessors for Tx DMA
- replace checks of DMA with checks of the unmap length to verify if an
unmap is needed
- update the Tx buffer layout to make it consistent with igb, ixgbe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
sk_pacing_rate is read by sch_fq packet scheduler at any time,
with no synchronization, so make sure we update it in a
sensible way. ACCESS_ONCE() is how we instruct compiler
to not do stupid things, like using the memory location
as a temporary variable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP listener refactoring, part 5 :
We want to be able to insert request sockets (SYN_RECV) into main
ehash table instead of the per listener hash table to allow RCU
lookups and remove listener lock contention.
This patch includes the needed struct sock_common in front
of struct request_sock
This means there is no more inet6_request_sock IPv6 specific
structure.
Following inet_request_sock fields were renamed as they became
macros to reference fields from struct sock_common.
Prefix ir_ was chosen to avoid name collisions.
loc_port -> ir_loc_port
loc_addr -> ir_loc_addr
rmt_addr -> ir_rmt_addr
rmt_port -> ir_rmt_port
iif -> ir_iif
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_receive() is currently limited to 16 or 17 MSS per GRO skb,
typically 24616 bytes, because it fills up to MAX_SKB_FRAGS frags.
It's relatively easy to extend the skb using frag_list to allow
more frags to be appended into the last sk_buff.
This still builds very efficient skbs, and allows reaching 45 MSS per
skb.
(45 MSS GRO packet uses one skb plus a frag_list containing 2 additional
sk_buff)
High speed TCP flows benefit from this extension by lowering TCP stack
cpu usage (less packets stored in receive queue, less ACK packets
processed)
Forwarding setups could be hurt, as such skbs will need to be
linearized, although its not a new problem, as GRO could already
provide skbs with a frag_list.
We could make the 65536 bytes threshold a tunable to mitigate this.
(First time we need to linearize skb in skb_needs_linearize(), we could
lower the tunable to ~16*1460 so that following skb_gro_receive() calls
build smaller skbs)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a enhancement.
for the first node in fib_trie, newpos is 0, bit is 1.
Only for the leaf or node with unmatched key need calc pos.
Signed-off-by: baker.zhang <baker.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can only setup multicast address for network device when
net_device_ops->ndo_set_rx_mode is not null.
Some configurations need to add multicast address for net
device, such as netfilter cluster match module.
Add a fake ndo_set_rx_mode function to allow this operation.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx "completed" stat was part of the original rewrite for detecting
Tx hangs. However some time ago in ixgbe I determined that we could
just use the packets stat instead. Since then this stat was
removed from ixgbe and it serves no purpose in i40e so it can be
dropped.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
