The compatible DDR controllers may support DDR, DDR2, DDR3, DDR4 DRAM.
An individual controller doesn't support all of them. The EDAC driver
reads SDRAM_CFG to determine which mode is configured.
Add DDR4 and drop the defines used only in the mtype assignment.
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: morbidrsa@gmail.com
Cc: oss@buserror.net
Cc: stuart.yoder@nxp.com
Link: http://lkml.kernel.org/r/1470779760-16483-6-git-send-email-york.sun@nxp.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The mpc85xx-compatible DDR controllers are used on ARM-based SoCs too.
Carve out the DDR part from the mpc85xx EDAC driver in preparation to
support both architectures.
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Johannes Thumshirn <morbidrsa@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: oss@buserror.net
Cc: stuart.yoder@nxp.com
Link: http://lkml.kernel.org/r/1470946525-3410-1-git-send-email-york.sun@nxp.com
Signed-off-by: Borislav Petkov <bp@suse.de>
On e500v1, read fault exception enable (RFXE) controls whether assertion
of core_fault_in causes a machine check interrupt. Assertion of
core_fault_in can result from uncorrectable data error, such as an L2
multi-bit ECC error. It can also occur from a system error if logic on
the integrated device signals a fault for nonfatal errors. RFXE bit is
cleared out of reset, and should be left clear for normal operation.
Assertion of core_fault_in does not cause a machine check.
RFXE is set specifically for RIO (Rapid IO) and PCI for book E to catch
the errors by machine check. With this bit set, the EDAC driver can't
get the interrupt in case of uncorrectable error. So this bit is cleared
in favor of EDAC. However, the benefit of catching such uncorrectable
error doesn't outweigh the other errors which may hang the system.
Besides, e500v2 has different errors masked by RFXE, and e500mc doesn't
support this bit. It is more reasonable to leave RFXE as is in the EDAC
driver, and leave the uncorrectable errors triggering machine check for
e500v1.
Suggested-by: Scott Wood <oss@buserror.net>
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Johannes Thumshirn <morbidrsa@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: oss@buserror.net
Cc: stuart.yoder@nxp.com
Link: http://lkml.kernel.org/r/1470779760-16483-2-git-send-email-york.sun@nxp.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The L2 and OCRAM devices have different ecc trigger names than the other
EDAC devices (FIFO peripherals). Make them all the same and remove the
character array from the device structure.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1471622666-15197-2-git-send-email-tthayer@opensource.altera.com
Signed-off-by: Borislav Petkov <bp@suse.de>
According to the reference manual of MPC8572 and T4240, bit 31 of
PEX_ERR_CAP_STAT is W1C (write 1 to clear).
Add the corresponding write to PEX_ERR_CAP_STAT in order to fix the PCIe
error capture.
Tested on a T4240 processor.
Signed-off-by: Tillmann Heidsieck <theidsieck@leenox.de>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20160815190849.29327-1-theidsieck@leenox.de
Signed-off-by: Borislav Petkov <bp@suse.de>
Replace the deprecated create_singlethread_workqueue() with
alloc_ordered_workqueue() with WQ_MEM_RECLAIM. This is the identity
conversion.
It's not recommended to stall it from memory pressure. Hence,
WQ_MEM_RECLAIM has been set to ensure forward progress under memory
pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20160813164124.GA9077@Karyakshetra
Signed-off-by: Borislav Petkov <bp@suse.de>
Fix the following sparse warning:
drivers/edac/altera_edac.c:1649:23: warning:
symbol 'a10_eccmgr_ic_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: lkml <linux-kernel@vger.kernel.org>
Link: http://lkml.kernel.org/r/1470836667-11822-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Fam15hMod60h systems are using the channel decode of Fam15hMod30h which
gives incorrect results. Fam15hMod60h systems should use the generic
channel decode method plus a couple more cases.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1470236355-30039-1-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
* Minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mdxx
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"This last cycle, Thor was busy adding Arria10 eth FIFO support to the
altera_edac driver along with other improvements. We have two
cleanups/fixes too.
Summary:
- Altera Arria10 ethernet FIFO buffer support (Thor Thayer)
- Minor cleanups"
* tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
ARM: dts: Add Arria10 Ethernet EDAC devicetree entry
EDAC, altera: Add Arria10 Ethernet EDAC support
EDAC, altera: Add Arria10 ECC memory init functions
Documentation: dt: socfpga: Add Arria10 Ethernet binding
EDAC, altera: Drop some ifdeffery
EDAC, altera: Add panic flag check to A10 IRQ
EDAC, altera: Check parent status for Arria10 EDAC block
EDAC, altera: Make all private data structures static
EDAC: Correct channel count limit
EDAC, amd64_edac: Init opstate at the proper time during init
EDAC, altera: Handle Arria10 SDRAM child node
EDAC, altera: Add ECC Manager IRQ controller support
Documentation: dt: socfpga: Add interrupt-controller to ecc-manager
In commit 2c1ea4c700 ("EDAC, sb_edac: Use cpu family/model in driver
detection") I broke Knights Landing because I failed to notice that it
called a wrapper macro "sbridge_get_all_devices_knl" instead of
"sbridge_get_all_devices" like all the other types.
Now that we include the processor type in the pci_id_table structure we
can skip the wrappers and just have the sbridge_get_all_devices() check
the type to decide whether to allow duplicate devices and controllers to
have registers spread across buses.
Fixes: 2c1ea4c700 ("EDAC, sb_edac: Use cpu family/model in driver detection")
Tested-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for additional memory module ECCs, the IRQ function will
check a panic flag before doing a kernel panic on double bit errors.
OCRAM uncorrectable errors cause a panic because sleep/resume functions
and FPGA contents during sleep are stored in OCRAM.
ECCs on peripheral FIFO buffers will not cause a kernel panic on DBERRs
because the packet can be retried and therefore recovered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1466603939-7526-3-git-send-email-tthayer@opensource.altera.com
Signed-off-by: Borislav Petkov <bp@suse.de>
c44696fff0 ("EDAC: Remove arbitrary limit on number of channels")
lifted the arbitrary limit on memory controller channels in EDAC.
However, the dynamic channel attributes dynamic_csrow_dimm_attr and
dynamic_csrow_ce_count_attr remained 6.
This wasn't a problem except channels 6 and 7 weren't visible in sysfs
on machines with more than 6 channels after the conversion to static
attr groups with
2c1946b6d6 ("EDAC: Use static attribute groups for managing sysfs entries")
[ without that, we're exploding in edac_create_sysfs_mci_device()
because we're dereferencing out of the bounds of the
dynamic_csrow_dimm_attr array. ]
Add attributes for channels 6 and 7 along with a guard for the
future, should more channels be required and/or to sanity check for
misconfigured machines.
We still need to check against the number of channels present on the MC
first, as Thor reported.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reported-by: Hironobu Ishii <ishii.hironobu@jp.fujitsu.com>
Tested-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org> # 4.2
It is useless to do it if we're loaded on unsupported hardware so do
that only after we have detected at least 1 supported AMD northbridge.
Signed-off-by: Borislav Petkov <bp@suse.de>
Separate the device match arrays for each platform to prevent CycloneV
matches when calling of_platform_populate() on the Arria10 ECC manager
node.
If the SDRAM is a child node of ECC manager, call probe function via
of_platform_populate().
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1464193783-5071-4-git-send-email-tthayer@opensource.altera.com
Signed-off-by: Borislav Petkov <bp@suse.de>
In commit
2c1ea4c700 ("EDAC, sb_edac: Use cpu family/model in driver detection")
we switched from using PCI ids to determine which platform we are
running on to using CPU model instead.
I forgot that Broadwell-DE has its own distinct model number different
from Broadwell-EP or -EX.
Fixing this isn't just adding a line to the array of cpuids - the
exising code assumed a 1:1 mapping between entries in that array and the
"enum type" values. Added the type to pci_id_table structure to remove
this dependency and allows two Broadwell cpu models.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 2c1ea4c700 ("EDAC, sb_edac: Use cpu family/model in driver detection")
Link: http://lkml.kernel.org/r/b3cffe40dec6dfe0235a5d52a504f0ba86a07ce7.1464902605.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Broadwell made a small change to the rank target register moving the
target rank ID field up from bits 16:19 to bits 20:23.
Also found that the offset field grew by one bit in the IVY_BRIDGE to
HASWELL transition, so fix the RIR_OFFSET() macro too.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: stable@vger.kernel.org # v3.19+
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/2943fb819b1f7e396681165db9c12bb3df0e0b16.1464735623.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
* Remove ad-hoc buffering of MCE records in sb_edac and i7core_edac. (Tony Luck)
* Do not register sb_edac with pci_register_driver(). (Tony Luck)
* Add support for Skylake to ie31200_edac. (Jason Baron)
* Do not register amd64_edac with pci_register_driver(). (Borislav Petkov)
+ the usual round of cleanups and fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ud2P
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"It was pretty busy in EDAC land this time:
- Altera Arria10 L2 cache and On-Chip RAM ECC handling (Thor Thayer)
- Remove ad-hoc buffering of MCE records in sb_edac and i7core_edac
(Tony Luck)
- Do not register sb_edac with pci_register_driver() (Tony Luck)
- Add support for Skylake to ie31200_edac (Jason Baron)
- Do not register amd64_edac with pci_register_driver() (Borislav
Petkov)
... plus the usual round of cleanups and fixes all over the place"
* tag 'edac_for_4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (25 commits)
EDAC, amd64_edac: Drop pci_register_driver() use
EDAC, ie31200_edac: Add Skylake support
EDAC, sb_edac: Use cpu family/model in driver detection
EDAC, i7core: Remove double buffering of error records
EDAC, amd64_edac: Issue driver banner only on success
ARM: socfpga: Initialize Arria10 OCRAM ECC on startup
EDAC: Increment correct counter in edac_inc_ue_error()
EDAC, sb_edac: Remove double buffering of error records
EDAC: Fix used after kfree() error in edac_unregister_sysfs()
EDAC, altera: Avoid unused function warnings
EDAC, altera: Remove useless casts
ARM: socfpga: Enable Arria10 OCRAM ECC on startup
EDAC, altera: Add Arria10 OCRAM ECC support
Documentation: dt: socfpga: Add Altera Arria10 OCRAM binding
EDAC, altera: Make OCRAM ECC dependency check generic
EDAC, altera: Add register offset for ECC Enable
EDAC, altera: Extract error inject operations to a struct fops
ARM: socfpga: Enable Arria10 L2 cache ECC on startup
EDAC, altera: Add Arria10 L2 Cache ECC handling
Documentation, dt, socfpga: Add Altera Arria10 L2 cache binding
...
Use X86_FEATURE_SMCA when detecting if SMCA is available instead of
directly using CPUID 0x80000007_EBX.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462971509-3856-7-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- remove homegrown instances counting.
- take F3 PCI device from amd_nb caching instead of F2 which was used with the
PCI core.
With those changes, the driver doesn't need to register a PCI driver and
relies on the northbridges caching which we do anyway on AMD.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Skylake adjusts some register locations, but otherwise follows the
existing model quite closely. I was able to verify that the 'ce_count'
increments when 'bad dimms' are used. The accounting of 'ce_count' and
'ue_count' is the primary functionality of interest for us. Tested on
Intel(R) Xeon(R) CPU E3-1260L v5 @ 2.90GHz.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1462547927-22679-1-git-send-email-jbaron@akamai.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Instead of picking a random PCI ID from the dozen or so we need to
access, just use x86_match_cpu() to pick based on CPU model number. The
choosing of PCI devices has been problematic in the past, see
11249e7399 ("sb_edac: Fix detection on SNB machines")
which fixed problems introduced by
d0585cd815 ("sb_edac: Claim a different PCI device").
This is especially ugly if future hardware might not even have
EDAC-relevant registers in PCI config space and we would still be
required to choose some "random" PCI devices to scan for just so our
driver loads.
Is this cleaner/clearer? It deletes much more code than it adds. Only
tested on Broadwell. The driver loads/unloads and loads again. Still
decodes errors too.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
In the bad old days the functions from x86_mce_decoder_chain could be
called in machine check context. So we used to carefully copy them and
defer processing until later. But in
f29a7aff4b ("x86/mce: Avoid potential deadlock due to printk() in MCE context")
we switched the logging code to save the record in a genpool, and call
the functions that registered to be notified later from a work queue.
So drop all the double buffering and do all the work we want to do as
soon as i7core_mce_check_error() is called.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/29ab2c370915c6e132fc5d88e7b72cb834bedbfe.1461855008.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Both of these drivers can return NOTIFY_BAD, but this terminates
processing other callbacks that were registered later on the chain.
Since the driver did nothing to log the error it seems wrong to prevent
other interested parties from seeing it. E.g. neither of them had even
bothered to check the type of the error to see if it was a memory error
before the return NOTIFY_BAD.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/72937355dd92318d2630979666063f8a2853495b.1461864507.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
In the bad old days the functions from x86_mce_decoder_chain could be
called in machine check context. So we used to carefully copy them and
defer processing until later. But in
f29a7aff4b ("x86/mce: Avoid potential deadlock due to printk() in MCE context")
we switched the logging code to save the record in a genpool, and call
the functions that registered to be notified later from a work queue.
So drop all the double buffering and do all the work we want to do as
soon as sbridge_mce_check_error() is called.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: patrickg@supermicro.com
Link: http://lkml.kernel.org/r/100025611cd780d9bca72792b2b2146760da53e0.1460756761.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Code flow looks like this:
device_unregister(&mci->dev);
-> kobject_put+0x25/0x50
-> kobject_cleanup+0x77/0x190
-> device_release+0x32/0xa0
-> mci_attr_release+0x36/0x70
-> kfree(mci);
bus_unregister(mci->bus);
Fix is to grab a local copy of "mci->bus" and use that when we call
bus_unregister().
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/21d595b0ab3d718d9cb206647f4ec91c05e62ec4.1461261078.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The recently added Arria10 OCRAM ECC support caused some new harmless
warnings about unused functions when it is disabled:
drivers/edac/altera_edac.c:1067:20: error: 'altr_edac_a10_ecc_irq' defined but not used [-Werror=unused-function]
drivers/edac/altera_edac.c:658:12: error: 'altr_check_ecc_deps' defined but not used [-Werror=unused-function]
This rearranges the code slightly to have those two functions inside
of the same #ifdef that hides their callers. It also manages to
avoid a forward declaration of the IRQ handler in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: c7b4be8db8 ("EDAC, altera: Add Arria10 OCRAM ECC support")
Link: http://lkml.kernel.org/r/1460837650-1237650-2-git-send-email-arnd@arndb.de
Signed-off-by: Borislav Petkov <bp@suse.de>
The altera EDAC driver refers to its per-device data
using a cast to '(void *)', which makes the pointer
non-const, though both the source and destination are
actually const.
Removing the annotation makes the reference (almost)
fit into a single line for improved readability, and
ensures that it is actually defined as const.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1460837650-1237650-1-git-send-email-arnd@arndb.de
Signed-off-by: Borislav Petkov <bp@suse.de>
Haswell and Broadwell can be configured to hash the channel
interleave function using bits [27:12] of the physical address.
On those processor models we must check to see if hashing is
enabled (bit21 of the HASWELL_HASYSDEFEATURE2 register) and
act accordingly.
Based on a patch by patrickg <patrickg@supermicro.com>
Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In commit:
eb1af3b71f ("Fix computation of channel address")
I switched the "sck_way" variable from holding the log2 value read
from the h/w to instead be the actual number. Unfortunately it
is needed in log2 form when used to shift the address.
Tested-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: eb1af3b71f ("Fix computation of channel address")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fix spelling typos found in printk
within various part of the kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
