The merge commit "526b264 Merge branch 'imx/cleanup' into imx/devel"
left a duplicated mx28_add_mxs_mmc() call, which causes the problem
below during boot.
kobject_add_internal failed for mxs-mmc.1 with -EEXIST, don't try
to register things with the same name in the same directory.
The patch removes this leftover and also change mmc0 adding to align
with mmc1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
This helps resolve the conflicts between the imx cleanups and the
new code that has gone into the imx tree.
Conflict resolution was originally done by Sascha Hauer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently framebuffer and MMC devices are registered even if their associated
GPIO pins fail to be requested.
Change the logic so that the registration of such devices only occurs if their
GPIO requests succeeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It adds LED2 on mx28evk board as heartbeat trigger for diagnostic
purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the mxs driver. Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.
v2: Removed header file entirely and put struct definition directly
into driver. The struct isn't used anywhere else in the kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code does not set the GPIO value to zero as mentioned in the comment.
Fix it by setting the initial GPIO value to zero.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301427910-31726-1-git-send-email-fabio.estevam@freescale.com
[ukleinek: squashed two patches together fixing both boards at once]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Read fec mac address from ocotp and save it into fec_platform_data
mac field for fec driver to use.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
