Uwe Kleine-König pointed out we still have one resource leak in the mvebu
driver triggered on driver detach. Let's address it with a custom devm
action.
Fixes: 812d47889a ("gpio/mvebu: Use irq_domain_add_linear")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This allows to get rid of a call to pwmchip_remove() in the error path. There
is no .remove function for this driver, so this change fixes a resource leak
when a gpio-mvebu device is unbound.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
To check if a certain function (here e.g. pwmchip_add()) can be called
IS_REACHABLE is the better check. The relevant difference to IS_ENABLED
is that IS_REACHABLE evaluates to 0 if the current code is builtin but the
checked symbol is =m and so must not be used.
Today there is no practical impact as CONFIG_PWM is a bool.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm support incompatible with Armada 80x0/70x0 API is not only in
Armada 370, but also in Armada XP, 38x and 39x. So basically every non-A8K
platform. Fix check for pwm support appropriately.
Fixes: 85b7d8abfe ("gpio: mvebu: add pwm support for Armada 8K/7K")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Based on the normalized pattern:
this file is licensed under the terms of the gnu general public
license version 2 this program is licensed as is without any warranty
of any kind whether express or implied
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't take struct pwm_state::polarity into account when
configuring the hardware, so refuse requests for inverted polarity.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
pwmchip_add() unconditionally assigns the base ID dynamically. Commit
f9a8ee8c8b ("pwm: Always allocate PWM chip base ID dynamically")
dropped all base assignment from drivers under drivers/pwm/. It missed
this driver. Fix that.
Fixes: f9a8ee8c8b ("pwm: Always allocate PWM chip base ID dynamically")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.
For the details one may look into the of_gpio_dev_init() implementation.
While at it, remove duplicate parent device assignment where it is the case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Use the marvell,pwm-offset DT property to store the location of PWM
signal duration registers.
Since we have more than two GPIO chips per system, we can't use the
alias id to differentiate between them. Use the offset value for that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Hardware appears to treat zero value as 2^32. Take advantage of this
fact to support on/off values of up to UINT_MAX+1 == 2^32. Adjust both
.apply and .get_state to handle zero as a special case.
Rounded up division result in .get_state can't be zero, since the
dividend is now larger than 0. Remove check for this case.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Analyzed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
PWM on/off registers are limited to UINT_MAX. However the state period
and duty_cycle fields are ns values of type u64. There is no reason to
limit them to UINT_MAX.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Round up the divisions in .get_state() to make applying the read out
configuration idempotent in most cases as .apply rounds down.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The period is the sum of on and off values. That is, calculate period as
($on + $off) / clkrate
instead of
$off / clkrate - $on / clkrate
that makes no sense.
Reported-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips
now use the template struct gpio_irq_chip and pass that to the core
to be set up alongside the gpio_chip. We can finally get rid of
the old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME
(wall clock) timestamps. We have found solid use cases for
this, so we support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which
is pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device
tree client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for
register access.
-----BEGIN PGP SIGNATURE-----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=nrFU
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.11 kernel cycle:
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips now
use the template struct gpio_irq_chip and pass that to the core to
be set up alongside the gpio_chip. We can finally get rid of the
old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME (wall
clock) timestamps. We have found solid use cases for this, so we
support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which is
pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device tree
client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for register
access"
* tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
MAINTAINERS: Remove reference to non-existing file
gpio: hisi: Do not require ACPI for COMPILE_TEST
MAINTAINERS: Add maintainer for HiSilicon GPIO driver
gpio: gpio-hisi: Add HiSilicon GPIO support
gpio: cs5535: Simplify the return expression of cs5535_gpio_probe()
gpiolib: irq hooks: fix recursion in gpiochip_irq_unmask
dt-bindings: mt7621-gpio: convert bindings to YAML format
gpiolib: cdev: Flag invalid GPIOs as used
gpio: put virtual gpio device into their own submenu
drivers: gpio: amd8111: use SPDX-License-Identifier
drivers: gpio: amd8111: prefer dev_err()/dev_info() over raw printk
drivers: gpio: bt8xx: prefer dev_err()/dev_warn() over of raw printk
gpio: Add TODO item for debugfs interface
gpio: just plain warning when nonexisting gpio requested
tools: gpio: add option to report wall-clock time to gpio-event-mon
tools: gpio: add support for reporting realtime event clock to lsgpio
gpiolib: cdev: allow edge event timestamps to be configured as REALTIME
gpio: msc313: MStar MSC313 GPIO driver
dt-bindings: gpio: Binding for MStar MSC313 GPIO controller
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
...
Commit 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
changed most readl/writel registers access calls to the regmap API in
preparation for Armada 7K/8K support. PWM duration registers were left using
readl/writel, as the driver does not support PWM for Armada 7K/8K.
Switch PWM duration registers to regmap as first step in adding Armada 7K/8K
PWM functionality support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200615150545.87964-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PWM iomem resource is optional and its presence indicates whether
the GPIO chip has a PWM or not, which is why mvebu_pwm_probe() returned
successfully when the PWM resource was not present. With f51b18d92b
the driver switched to devm_platform_ioremap_resource_byname() and
its error return is propagated to the caller, so now a missing PWM resource
leads to a probe error in the driver.
To fix this explicitly test for the presence of the PWM resource and
return successfully when it's not there. Do this check before the check
for the clock is done (which GPIO chips without a PWM do not have). Also
move the existing comment why the PWM resource is optional up to the
actual check.
Fixes: f51b18d92b ("gpio: mvebu: use devm_platform_ioremap_resource_byname()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
platform_get_irq() will generate an error message if the requested irq
is not present
mvebu-gpio f1010140.gpio: IRQ index 3 not found
use platform_get_irq_optional() to avoid the error message being
generated.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When input GPIO set from 0 to 1, the interrupt bit asserted in the GPIO
Interrupt Cause Register (ICR) even if the corresponding interrupt
masked in the GPIO Interrupt Mask Register.
Because interrupt mask register only affects assertion of the interrupt
bits in Main Interrupt Cause Register and it does not affect the
setting of bits in the GPIO ICR.
So, there is problem, when we unmask interrupt with already
asserted bit in the GPIO ICR, then false interrupt immediately occurs
even if GPIO don't change their value since last unmask.
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20200115073811.24438-1-bigunclemax@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_irq_count() is the more generic way (independent of
device trees) to determine the count of available interrupts. So
use this instead.
As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:
#define PERIOD 5000000
#define DUTY_LITTLE 10
...
struct pwm_state state = {
.period = PERIOD,
.duty_cycle = DUTY_LITTLE,
.polarity = PWM_POLARITY_NORMAL,
.enabled = true,
};
pwm_apply_state(mypwm, &state);
...
state.duty_cycle = PERIOD / 2;
pwm_apply_state(mypwm, &state);
For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.
So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When a gpio_chip wants to request a descriptor from itself
using gpiochip_request_own_desc() it needs to be able to specify
fully how to use the descriptor, notably line inversion
semantics. The workaround in the gpiolib.c can be removed
and cases (such as SPI CS) where we need at times to request
a GPIO with line inversion semantics directly on a chip for
workarounds, can be fully supported with this call.
Fix up some users of the API that weren't really using the
last flag to set up the line as input or output properly
but instead just calling direction setting explicitly
after requesting the line.
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip documentation recommends to always implement this
callback function.
A more concrete motivation is to be able (in combination with
GPIOD_ASIS) to detect whether the bootloader has changed the state of a
GPIO signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MVEBU driver is requesting GPIO descriptors from itself, which
is fine, but we have proper APIs to do this in a controlled way, so
stop calling into the private functions of the GPIO library and use
the gpiochip_* functions instead. Only include <linux/gpio/driver.h>
and <linux/gpio/consumer.h> since we are both producers and consumers
in this case.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When switching to regmap, the way to compute the irq cause was
reorganized. However while doing it, a typo was introduced: a 'xor'
replaced a 'and'.
This lead to wrong behavior in the interrupt handler ans one of the
symptom was wrong irq handler called on the Armada 388 GP:
"->handle_irq(): c016303c,
handle_bad_irq+0x0/0x278
->irq_data.chip(): c0b0ec0c,
0xc0b0ec0c
->action(): (null)
IRQ_NOPROBE set
IRQ_NOREQUEST set
unexpected IRQ trap at vector 00
irq 0, desc: ee804800, depth: 1, count: 0, unhandled: 0"
Fixes: 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO line
may loose its state during suspend/resume of the system to save
power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes.
-----BEGIN PGP SIGNATURE-----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=TpW1
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
As it turns out more than just Armada 370 and XP support using GPIO
lines as PWM lines. For example the Armada 38x family has the same
hardware support. As such "marvell,armada-370-xp-gpio" for the
compatible string is a misnomer.
Change the compatible string to "marvell,armada-370-gpio" before the
driver makes it out of the -rc stage. This also follows the practice of
using only the first device family supported as part of the name.
Also update the documentation and comments in the code accordingly.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 7K and 8K SoCs use the same gpio controller as most of the
other mvebu SoCs. However, the main difference is that the GPIO
controller is part of a bigger system controller, and a syscon is used to
control the overall system controller. Therefore, the driver needs to be
adjusted to retrieve the regmap of the syscon to access registers, and
account for the fact that registers are located at a certain offset
within the regmap.
This commit add the support of the syscon and introduce a new variant for
this case.
It was based on the preliminary work of Thomas Petazzoni.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some place in the driver regmap_update_bits was misused. Indeed the
last argument is not the value of the bit (or group of bits) itself but
the mask value inside the register.
So when setting the bit N, then the value must be BIT(N) and not 1.
CC: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If more than one gpio bank has the "pwm" property, only one will be
registered successfully, all the others will fail with:
mvebu-gpio: probe of f1018140.gpio failed with error -17
That's because in alloc_pwms(), the chip->base (aka "int pwm"), was not
set (thus, ==0) ; and 0 is a meaningful start value in alloc_pwm().
What was intended is mvpwm->chip->base = -1.
Like that, the numbering will be done auto-magically
Moreover, as the region might be already occupied by another pwm, we
shouldn't force:
mvpwm->chip->base = 0
nor
mvpwm->chip->base = id * MVEBU_MAX_GPIO_PER_BANK;
Tested on clearfog-pro (Marvell 88F6828)
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The blink counter A was always selected because 0 was forced in the
blink select counter register.
The variable 'set' was obviously there to be used as the register value,
selecting the B counter when id==1 and A counter when id==0.
Tested on clearfog-pro (Marvell 88F6828)
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to be able to use this driver with the Armada 7K/8K SoCs, we
need to use the regmap to access the registers. Indeed for these new SoCs,
the gpio node will be part of a syscon.
[gregory.clement@free-electrons.com:
- fixed merge conflcit from 4.10 to 4.12-rc1
- added a commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 370/XP devices can 'blink' GPIO lines with a configurable on
and off period. This can be modelled as a PWM.
However, there are only two sets of PWM configuration registers for
all the GPIO lines. This driver simply allows a single GPIO line per
GPIO chip of 32 lines to be used as a PWM. Attempts to use more return
EBUSY.
Due to the interleaving of registers it is not simple to separate the
PWM driver from the GPIO driver. Thus the GPIO driver has been
extended with a PWM driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427287/
URL: https://patchwork.ozlabs.org/patch/427295/
[Ralph Sennhauser:
* Port forward
* Merge PWM portion into gpio-mvebu.c
* Switch to atomic PWM API
* Add new compatible string marvell,armada-370-xp-gpio
* Update and merge documentation patch
* Update MAINTAINERS]
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the BIT macro instead of explicitly shifting bits for some added
clarity.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A modern compiler should know better when to inline, so drop the inline
keywords.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use unsigned int instead of plain unsigned as reported by checkpatch.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
