Handle usb-device resets not triggered from uas_eh_bus_reset_handler(), when
this happens, disable cmd queuing during the reset, and wait for existing
requests to finish in pre_reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Fix the uas_eh_bus_reset_handler not properly taking the usbdev lock
before calling usb_device_reset, the usb-core expects this lock to be
taken when usb_device_reset is called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
I thought it would be a good idea to also test uas with usb-2, and it turns out
it was, as it did not work. The problem is that the uas driver was passing the
bEndpointAddress' direction bit to usb_rcvbulkpipe, the xhci code seems to not
care about this, but with the ehci code this causes usb_submit_urb failure.
With this fixed the uas code works nicely with an uas device plugged into
an ehci port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The cmd endpoint never has streams, so the stream_id parameter is unused.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
All callers of unlink_data_urbs drop devinfo->lock before calling it, and
then immediately take it again after the call. And the first thing
unlink_data_urbs does is take the lock again, and the last thing it does
is drop it. This commit removes all the unnecessary lock dropping and taking.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
- Rename labels to properly reflect this
- Don't skip free-ing the streams when scsi_init_shared_tag_map fails
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Otherwise they may complete before they get anchored and thus never get
unanchored (as the unanchoring is done by the usb core on completion).
This commit also remove the usb_get_urb / usb_put_urb around cmd submission +
anchoring, since if done in the proper order this is not necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new list where all requests which are canceled are
added to, so we don't loose them. Then, after killing all inflight
urbs on bus reset (and disconnect) we'll walk over the list and clean
them up.
Without this we can end up with aborted requests lingering around in
case of status pipe transfer errors.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Simplifies locking, we'll protect the list with the device spin lock.
Also plugs races which can happen when two devices operate on the
global list.
While being at it rename the list head from "list" to "work", preparing
for the addition of a second list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
People sometimes create their own custom-configured kernels and forget
to enable CONFIG_SCSI_MULTI_LUN. This causes problems when they plug
in a USB storage device (such as a card reader) with more than one
LUN.
Fortunately, we can tell fairly easily when a storage device claims to
have more than one LUN. When that happens, this patch asks the SCSI
layer to probe all the LUNs automatically, regardless of the config
setting.
The patch also updates the Kconfig help text for usb-storage,
explaining that CONFIG_SCSI_MULTI_LUN may be necessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Thomas Raschbacher <lordvan@lordvan.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an unusual-devs entry for the BlackBerry 9000. This
fixes Bugzilla #22442.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Moritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Tested-by: Moritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress ATACB unusual-devs entry for the Super Top SATA bridge
causes problems. Although it was originally reported only for
bcdDevice = 0x160, its range was much larger. This resulted in a bug
report for bcdDevice 0x220, so the range was capped at 0x219. Now
Milan reports errors with bcdDevice 0x150.
Therefore this patch restricts the range to just 0x160.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Milan Svoboda <milan.svoboda@centrum.cz>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170
The workaround is (MAX_SECTORS_64):
rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m
The patch adds the tested device to the unusual list permanently.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch should fix the below compile warning:
drivers/usb/storage/protocol.c: In function 'usb_stor_access_xfer_buf':
drivers/usb/storage/protocol.c:155:22: warning: comparison of distinct
pointer types lacks a cast [enabled by default]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have sg_miter_* APIs for accessing scsi sg buffer, so
use them to make code clean and bug free.
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the usbsorage sysfs attribute to use the _RW macro to make it
easier to determine the permissions for the file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device report an error capacity when read_capacity_16().
Using read_capacity_10() can get the correct capacity.
Signed-off-by: Ren Bigcren <bigcren.ren@sonymobile.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the code a bit to initialize the variables directly when
defining them.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the code a bit to initialize the variables directly when
defining them.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix the compile error when CONFIG_PM_RUNTIME is not enabled,
move the declaration of us out of CONFIG_REALTEK_AUTOPM macro in rts51x_chip.
drivers/usb/storage/realtek_cr.c: In function 'realtek_cr_destructor':
drivers/usb/storage/realtek_cr.c:942:11: error: 'struct rts51x_chip' has no member named 'us'
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Remove unused local `us', which broke the build. Also nuke an unneeded
cast.
Repairs commit 191648d03d ("usb: storage: Convert US_DEBUGP to
usb_stor_dbg").
Cc: Joe Perches <joe@perches.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many cards based on CY7C68300A/B/C use the USB ID 04b4:6830 but only the
B and C variants (EZ-USB AT2LP) support the ATA Command Block
functionality, according to the data sheets. The A variant (EZ-USB AT2)
locks up if ATACB is attempted, until a typical 30 seconds timeout runs
out and a USB reset is performed.
https://bugs.launchpad.net/bugs/428469
It seems that one way to spot a CY7C68300A (at least where the card
manufacturer left Cypress' EEPROM default vaules, against Cypress'
recommendations) is to look at the USB string descriptor indices.
A http://media.digikey.com/pdf/Data%20Sheets/Cypress%20PDFs/CY7C68300A.pdf
B http://www.farnell.com/datasheets/43456.pdf
C http://www.cypress.com/?rID=14189
Note that a CY7C68300B/C chip appears as CY7C68300A if it is running
in Backward Compatibility Mode, and if ATACB would be supported in this
case there is anyway no way to tell which chip it really is.
For 5 years my external USB drive has been locking up for half a minute
when plugged in and ata_id is run by udev, or anytime hdparm or similar
is run on it.
Finally looking at the /correct/ datasheet I think I found the reason. I
am aware the quirk in this patch is a bit hacky, but the hardware
manufacturers haven't made it easy for us.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that Joe cleaned up the init/exit functions, we can just get rid of
them entirely and use the proper macro that almost all other USB drivers
now use.
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a more current logging style with dev_printk
where possible.
o Convert uses of US_DEBUGP to usb_stor_dbg
o Add "struct us_data *" to usb_stor_dbg uses
o usb_stor_dbg now uses struct device */dev_vprint_emit
o Removed embedded function names
o Coalesce formats
o Remove trailing whitespace
o Remove useless OOM messages
o Remove useless function entry/exit logging
o Convert some US_DEBUGP uses to dev_info and dev_dbg
Object size is slightly reduced when debugging
is enabled, slightly increased with no debugging
because some initialization and removal messages
are now always emitted.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the size of the objects by consolidating
the duplicated USB_STORAGE into a single function.
Add function usb_stor_dbg to emit debugging messages.
Always validate the format and arguments.
Reduce the number of uses of CONFIG_USB_STORAGE_DEBUG.
Reduces size of objects ~7KB when CONFIG_USB_STORAGE_DEBUG
is set.
$ size drivers/usb/storage/built-in.o*
text data bss dec hex filename
140133 55296 70312 265741 40e0d drivers/usb/storage/built-in.o.new
147494 55248 70296 273038 42a8e drivers/usb/storage/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the fixes in that branch, and let Alan fix the merge
error in drivers/usb/host/ehci-timer.c better than I just did (as I know
I messed it up...)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains because we only allocate ONETOUCH_PKT_LEN (2) bytes
but later when we call usb_fill_int_urb() we assume maxp can be up
to 8 bytes. I talked to the maintainer and maxp should be capped at
ONETOUCH_PKT_LEN.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 200e0d99 ("USB: storage: optimize to match the
Huawei USB storage devices and support new switch command" and the
followup bugfix commit cd060956 ("USB: storage: properly handle
the endian issues of idProduct").
The commit effectively added a large number of Huawei devices to
the deprecated usb-storage mode switching logic. Many of these
devices have been in use and supported by the userspace
usb_modeswitch utility for years. Forcing the switching inside
the kernel causes a number of regressions as a result of ignoring
existing onfigurations, and also completely takes away the ability
to configure mode switching per device/system/user.
Known regressions caused by this:
- Some of the devices support multiple modes, using different
switching commands. There are existing configurations taking
advantage of this.
- There is a real use case for disabling mode switching and
instead mounting the exposed storage device. This becomes
impossible with switching logic inside the usb-storage driver.
- At least on device fail as a result of the usb-storage switching
command, becoming completely unswitchable. This is possibly a
firmware bug, but still a regression because the device work as
expected using usb_modeswitch defaults.
In-kernel mode switching was deprecated years ago with the
development of the more user friendly userspace alternatives. The
existing list of devices in usb-storage was only kept to prevent
breaking already working systems. The long term plan is to remove
the list, not to add to it. Ref:
http://permalink.gmane.org/gmane.linux.usb.general/28543
Cc: <fangxiaozhi@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current entry in unusual_cypress.h for the Super TOP SATA bridge devices
seems to be causing corruption on newer revisions of this device. This has
been reported in Arch Linux and Fedora. The original patch was tested on
devices with bcdDevice of 1.60, whereas the newer devices report bcdDevice
as 2.20. Limit the UNUSUAL_DEV entry to devices less than 2.20.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=909591
The Arch Forum post on this is here:
https://bbs.archlinux.org/viewtopic.php?id=152011
Reported-by: Carsten S. <carsteniq@yahoo.com>
Tested-by: Carsten S. <carsteniq@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. The idProduct is little endian, so make sure its value to be
compatible with the current CPU. Make no break on big endian processors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Optimize the match rules with new macro for Huawei USB storage devices,
to avoid to load USB storage driver for the modem interface
with Huawei devices.
2. Add to support new switch command for new Huawei USB dongles.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Define a new macro for USB storage match rules:
matching with Vendor ID and interface descriptors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
256 luns is what the sam-4 address method 0 can handle and what
the qemu uas emulation supports. So pick that for now.
[ v2: unlike the other two max_* fields max_channel isn't max+1 ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets scsi_host->max_id as 1 if the device's quirk
flag of US_FL_SCM_MULT_TARG isn't set, because there are only 6
mass storage devices marked as mutiple targets from unusual_devs.h.
This patch is a small optimization about scanning targets, and
avoid scanning other 7 non-existed targets for single target
device.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new function to unlink and abort requests from the work
list, call it on bus reset and disconnect where we kill all
in-flight urbs. Also reorder calls in disconnect to first
cancel transfers, then remove the scsi hba.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two changes. First we check whenever the request is linked in the work
list and if so take it out. Second check whenever the command is
actually in flight before asking the device to cancel it via task
management, and in case it isn't just zap the data urbs and finish it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
