The amount of TX/RX buffers that the vNIC driver currently allocates
is different from the amount agreed upon in negotiation with firmware.
Correct that by allocating the requested number of buffers confirmed
by firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a counter to track the number of outstanding transmissions sent
that have not received completions. If the counter reaches the maximum
number of queue entries, stop transmissions on that queue. As we receive
more completions from firmware, wake the queue once the counter reaches
an acceptable level.
This patch prevents hardware/firmware TX queue from filling up and
and generating errors. Since incorporating this fix, internal testing
has reported that these firmware errors have stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue-code that allows the EMAC driver to interface
with the existing dt-supported PHYs in drivers/net/phy.
Because currently, the emac driver maintains a small library of
supported phys for in a private phy.c file located in the drivers
directory.
The support is limited to mostly single ethernet transceiver like the:
CIS8201, BCM5248, ET1011C, Marvell 88E1111 and 88E1112, AR8035.
However, routers like the Netgear WNDR4700 and Cisco Meraki MX60(W)
have a 5-port switch (AR8327N) attached to the EMAC. The switch chip
is supported by the qca8k mdio driver, which uses the generic phy
library. Another reason is that PHYLIB also supports the BCM54610,
which was used for the Western Digital My Book Live.
This will now also make EMAC select PHYLIB.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sending device capability queries and requests to the vNIC Server,
an interrupt is triggered and the responses are written to the driver's
CRQ response buffer. Since the interrupt can be triggered before all
responses are written and visible to the partition, there is a danger
that the interrupt handler or tasklet can terminate before all responses
are read, resulting in a failure to initialize the device.
To avoid this scenario, when capability commands are sent, we set
a flag that will be checked in the following interrupt tasklet that
will handle the capability responses from the server. Once all
responses have been handled, the flag is disabled; and the tasklet
is allowed to terminate.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different counters were being used for capabilities
requests and queries. These commands are not called
at the same time so there is no reason a single counter
cannot be used.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a tasklet to process queued commands or messages received from
firmware instead of processing them in the interrupt handler. Note that
this handler does not process network traffic, but communications related
to resource allocation and device settings.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error reports received from firmware were not being converted from
big endian values, leading to bogus error codes reported on little
endian systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include calculations to compute the number of segments
that comprise an aggregated large packet.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for netdev private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero the stats portion of it
again in the driver's probe function.
In any case, the size for the memset is wrong as the stats member is of
type rtnl_link_stats64, not net_device_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header seq_file.h from ibmvnic.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mistake was causing debugfs directory creation
failures when multiple ibmvnic devices were probed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was mapped but never subsequently unmapped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the opt_* fields to determine the starting point for negotiating the
number of tx/rx completion queues with the vnic server. These contain the
number of queues that the vnic server estimates that it will be able to
allocate. While renegotiation may still occur, using the opt_* fields will
reduce the number of times this needs to happen and will prevent driver
probe timeout on systems using large numbers of ibmvnic client devices per
vnic port.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.
This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d894be57ca92('ethernet: use net core MTU range checking in more drivers')
CC: Jarod Wilson <jarod@redhat.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the MTU to be changed during the initialization
process with the VNIC Server. Ensure that the net device is updated
to reflect the new MTU.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increment driver version to reflect features that have
been added since release.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: min_mtu 68, max_mtu 9022
- remove ehea_change_mtu, it's now redundant
emac: min_mtu 46, max_mtu 1500 or whatever gets read from OF
CC: netdev@vger.kernel.org
CC: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for preventing race conditions within ioctl calls.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add realization for mac address set and remove dummy callback.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd like to eventually remove NO_IRQ on powerpc, so remove usages of it
from powerpc-only drivers.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the dma_map_single error
handling case instead of 0, as done elsewhere in this function.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.
Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if there is no VNIC server available during the driver
probe, the driver should wait until it receives an initialization
request from the VNIC Server to start the login process. Recent testing
has show that this is incorrectly handled in the current driver.
The proposed solution handles this initialization request by scheduling
a task in the shared workqueue that completes the login process and
registers the net device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a function that handles sub-CRQ IRQ creation
separately from sub-CRQ initialization. Another function is then needed
to release sub-CRQ resources prior to sub-CRQ IRQ creation.
These additions allow the driver probe function to be simplified,
specifically during the VNIC Server login process. A timeout is also
included while waiting for completion of the login process in case
the VNIC Server is not available or some other error occurs.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ mappings were not being properly disposed when releasing sub-CRQ's.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ibmvnic uses multiple tx queues, start and stop all queues when
opening and closing devices.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each() macro aptly named
list_for_each_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea_get_port may return NULL. Do not dereference NULL value.
Fixes: 8c4877a412 ("ehea: Use the standard logging functions")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phy initialization code for Qualcomm
Atheros AR8035 phy. This configuration is found in the
Cisco Meraki MR24.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables the use of multiple transmit and receive scrqs allowing the ibmvnic
driver to take advantage of multiqueue functionality. To achieve this, the
driver must implement the process of negotiating the maximum number of
queues allowed by the server. Initially, the driver will attempt to login
with the maximum number of tx and rx queues supported by the server. If
the server fails to allocate the requested number of scrqs, it will return
partial success in the login response. In this case, we must reinitiate
the login process from the request capabilities stage and attempt to login
requesting fewer scrqs.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable RX Checksum offload feature in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the VNIC driver to provide descriptors containing
L2/L3/L4 headers to firmware. This feature is needed
for greater hardware compatibility and enablement of checksum
and TCP offloading features.
A new function is included for the hypervisor call,
H_SEND_SUBCRQ_INDIRECT, allowing a DMA-mapped array of SCRQ
descriptor elements to be sent to the VNIC server.
These additions will help fully enable checksum offloading as
well as other features as they are included later.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_linearize fails, the driver should drop the packet
instead of trying to copy it into the bounce buffer.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic_capability struct was defined incorrectly. The last two
elements of the struct are in the wrong order. In addition, the number
element should be 64-bit. Byteswapping functions are updated
as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new device driver for a high performance SR-IOV assisted virtual
network for IBM System p and IBM System i systems. The SR-IOV VF will be
attached to the VIOS partition and mapped to the Linux client via the
hypervisor's VNIC protocol that this driver implements.
This driver is able to perform basic tx and rx, new features
and improvements will be added as they are being developed and tested.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an API consolidation only. The use of kmalloc + memset to 0
is equivalent to kcalloc in this case as it is allocating an array
of elements.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the MAC register dump used to be the size specified by the
reg property in the device tree. Userland has no good way of finding
out that size, and it was not specified consistently for each MAC type,
so ethtool would end up printing junk at the end of the register dump
if the device tree didn't match the size it assumed.
Using the new version numbers indicates unambiguously that the size of
the MAC register dump is dependent only on the MAC type.
Fixes: 5369c71f7c ("net/ibm/emac: fix size of emac dump memory areas")
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_mode can be negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new method of signalling the firmware
that TSO packets are being sent. The new method removes the need to
alter the ip and tcp checksums and allows TSO6 support.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in send of emac regs dump to ethtool which
causing in wrong data interpretation on ethtool
layer for MII and EMAC.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables receiving large packets from other LPARs. These packets
have a -1 IP header checksum, so we must recalculate to have
a valid checksum.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TSO. TSO is turned off by default and
must be enabled and configured by the user. The driver
version number is increased so that users can be sure
that they are using ibmveth with TSO support.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables 64k rx buffer pools by default. If Cooperative
Memory Overcommitment (CMO) is enabled, the number of 64k buffers
is reduced to save memory.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to only register the EHEA memory hotplug hooks on
adapter probe has a few problems.
Firstly the reference counting is wrong for multiple adapters, in that
the hooks are registered multiple times. Secondly the check in the tear
down path is backward. Finally the error path doesn't decrement the
count.
The multiple registration of the hooks is the biggest problem, as it
leads to oopses when the system is rebooted, and/or errors during memory
hotplug, eg:
$ ./mem-on-off-test.sh -r 2
...
ehea: memory is going offline
ehea: LPAR memory changed - re-initializing driver
ehea: re-initializing driver complete
ehea: memory is going offline
ehea: LPAR memory changed - re-initializing driver
ehea: opcode=26c ret=fffffffffffffffc arg1=8000000003000003 arg2=0 arg3=700000060000d600 arg4=3fded0000 arg5=200 arg6=0 arg7=0
ehea: register_rpage_mr failed
ehea: registering mr failed
ehea: register MR failed - driver inoperable!
ehea: memory is going offline
Fixes: aa18332331 ("ehea: Register memory hotplug, reboot and crash hooks on adapter probe")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIK the PAPR document which defines the virtual device interface used by
the ibmveth driver doesn't specify a specific maximum MTU. So, in the
ibmveth driver, the maximum allowed MTU is determined by the maximum
allocated buffer size of 64k (corresponding to one page in the common case)
minus the per-buffer overhead IBMVETH_BUFF_OH (which has value 22 for 14
bytes of ethernet header, plus 8 bytes for an opaque handle).
This suggests a maximum allowable MTU of 65514 bytes, but in fact the
driver only permits a maximum MTU of 65513. This is because there is a <
instead of an <= in ibmveth_change_mtu(), which only permits an MTU which
is strictly smaller than the buffer size, rather than allowing the buffer
to be completely filled.
This patch fixes the buglet.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are only used from one place each. If the cacheable_*
versions really are more efficient, then those changes should be
migrated into the common code instead.
NOTE: The old routines are just flat buggy on kernels that support
hardware with different cacheline sizes.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea creates memory hotplug, reboot and crash hooks even if there
are no adapters in the box. Just create them when we probe our
first adapter.
[cascardo: use ehea_register_memory_hooks return code]
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver claims that it can do TSO and IP checksums on vlan
devices and also allows user to control vlan acceleration offloading.
This makes it possible to push traffic to this driver that has TSO or
partial checksums set, but also have a non-accelearted vlan
header. In this case, the driver will fail to correctly
identify such traffic and will not correctly perform
segmentation and checksum calculation.
Fix this by using vlan_get_protocol() helper instead of
assuming skb->protocol always has this information.
CC: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Makefile, ehea_phyp.o is included twice in the list of
object files compile into ehea.o.
This change removes one instance.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggreagation of version 1-2 because of version 1 can hit
PLB errors too. If it's not set so we missing events for PLB bits
and driver can't process those interrupts.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chips of emac/rgmii b'000' for 0/1 channel isn't suitable which
resulted in non working network interface in this mode.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Compile-Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_consume_skb_any in ibmveth_start_xmit
that can be called in hard irq and other contexts.
In this code path the packet can have either been transmitted
or dropped, dev_consume_skb_any was choosen because that preserves
the existing semantics of the code, and a transmitted packet is
more likely.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in functions that can
be called in hard irq and other contexts.
None of the locations was a packet drop so dev_kfree_skb_any is
inappropriate.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to load a MAC address into a u64 for passing to the
hypervisor via a register is broken on little endian.
Create a helper function called ibmveth_encode_mac_addr
which does the right thing in both big and little endian.
We were storing the MAC address in a long in struct ibmveth_adapter.
It's never used so remove it - we don't need another place in the
driver where we create endian issues with MAC addresses.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the generic iommu backend code to use the
it_page_shift field to determine the iommu page size instead of
using hardcoded values.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc iommu uses a hardcoded page size of 4K. This patch changes
the name of the IOMMU_PAGE_* macros to reflect the hardcoded values. A
future patch will use the existing names to support dynamic page
sizes.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Olof Johansson <olof@lixom.net>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Nicolas Pitre <nico@fluxnic.net>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few network drivers really supports frag_list : virtual drivers.
Some drivers wrongly advertise NETIF_F_FRAGLIST feature.
If skb with a frag_list is given to them, packet on the wire will be
corrupt.
Remove this flag, as core networking stack will make sure to
provide packets that can be sent without corruption.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to mal_enable_eob_irq perform a read-write-modify of a dcr to
enable device irqs which is protected by a spin lock. However calls to
mal_disable_eob_irq do not take the corresponding lock.
This patch resolves the problem by ensuring that calls to
mal_disable_eob_irq also take the lock.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug which would trigger the BUG_ON() at
net/core/dev.c:4156. It was found that this was due to continuing
processing in the current poll call even when the call to
napi_reschedule failed, indicating the device was already on the
polling list. This resulted in an extra call to napi_complete which
triggered the BUG_ON().
This patch ensures that we only contine processing rotting packets in
the current mal_poll call if we are not already on the polling list.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree
Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215
[ Thadeu notes that: "... this issue might happen with the generation of
initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
which links to the port device at
/sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Olaf Hering <ohering@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/ibm/ehea/ehea_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
ibmebus is the last remaining user of of_platform_driver and the
conversion to a regular platform driver is trivial.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
MCA support has been removed but this dependency escaped removal.
Also, there is a duplicate PPC_PSERIES dependency that appeared
when the ethernet drivers were separated into vendor/model
specific directories, so we remove that here as well.
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.
EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.
PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.
Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).
With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ancient pHyp versions used to create a 8 bytes local-mac-address
property in the device-tree instead of a 6 bytes one for veth.
The Linux driver code to deal with that is an insane hack which also
happens to break with some choices of MAC addresses in qemu by testing
for a bit in the address rather than just looking at the size of the
property.
Sanitize this by doing the latter instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
Currently help message of /proc/sysrq-trigger highlight its upper-case
characters, like below:
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E)
memory-full-oom-kill(F) kill-all-tasks(I) ...
this would confuse user trigger sysrq by upper-case character, which is
inconsistent with the real lower-case character registed key.
This inconsistent help message will also lead more confused when
26 upper-case letters put into use in future.
This patch ethernet emac sysrq key: "emac(c)"
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver uses the crummy "| foo" style, putting the
logical operation at the beginning of lines. Then
when the VLAN tag flag bits got changed the operator
ended up at both the end and the beginning of some lines.
Fix the build error by having it uniformly use the operator
at the end of the line.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several call sites were missed when the protocol argument was added to
__vlan_hwaccel_put_tag() in commit
86a9bad3ab ("net: vlan: add protocol
argument to packet tagging functions").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ehea.h the minimal entries is 2^7 - 1:
#define EHEA_MIN_ENTRIES_QP 127
Thus change the module param description accordinglly
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2cb1deb56f ('ehea: Remove LRO
support') left behind the Kconfig depends/select and feature flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am going to use this in the next patch, better to have this code in
one place rather than three.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression list es;
@@
-printk(
+WARN(1,
es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Cc: <stable@vger.kernel.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
abs_to_virt() simply calls __va() and we'd like to get rid of it,
so replace all abs_to_virt() uses with __va().
Similarly virt_to_abs() just calls __pa().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment. Delete a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NEQ interrupt is only triggered when there was no previous pending
interrupt. If we request irq handling after an interrupt has occurred,
we will never get an interrupt until we call H_RESET_EVENTS.
Events seem to be cleared when we first register the NEQ. So, when we
requested irq handling right after registering it, a possible race with
an interrupt was much less likely. Now, there is a chance we may lose
this race and never get any events.
The fix here is to poll and acknowledge any events that might have
happened right after registering the irq handler.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a4910b7444 has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.
However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
This driver is specific to the PowerPC legcay iSeries platform which is
being removed.
Cc: David Miller <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 239c562c94 (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes:
Configure EMAC PHY clock source (clock from PHY or internal clock).
Do not advertise PHY half duplex capability as APM821XX EMAC does not support half duplex mode.
Add changes to support configuring jumbo frame for APM821XX EMAC.
[ Fix coding style -DaveM ]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text. Bring them up to date. No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some functions and variables in ehea are only used in their own file, so
they should be static. One particular function had a very generic name,
print_error_data.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use round_jiffies_relative to align the ehea workqueue and avoid
extra wakeups.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable multiqueue by default the ehea driver is using
quite a lot of memory for its buffer pools. With 4 queues we
consume 64MB in the jumbo packet ring, 16MB in the medium packet
ring and 16MB in the tiny packet ring.
We should only fill the jumbo ring once the MTU is increased but
for now halve it's size so it consumes 32MB. Also reduce the tiny
packet ring, with 4 queues we had 16k entries which is overkill.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"remote_list" is of type
struct dma_chunk remote_list[VETH_MAX_FRAMES_PER_MSG];
Probably a copy'n'paste error.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The re-binding (unbind..bind) of an EMAC device fails because the
static variable "busy_phy_map" is not updated when the device is
removed.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcp_end field is not actually used by the hardware, so there
is no need to set it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add GRO support to the ehea driver.
v3:
[cascardo] no need to enable GRO, since it's enabled by default
[cascardo] vgrp was removed in the vlan cleanup
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding GRO to ehea, remove LRO.
v3:
[cascardo] fixed conflict with vlan cleanup
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to using ndo_get_stats64 to get 64bit statistics.
v3:
[cascardo] use rtnl_link_stats64 as port stats
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The queue macros are many levels deep and it makes it harder to
work your way through them when many of the versions are unused.
Remove the unused versions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a nonlinear skb fits within the immediate area, use skb_copy_bits
instead of copying the frags by hand.
v3:
[cascardo] fixed conflict with use of skb frag API
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_swqe2_TSO and write_swqe2_nonTSO are almost identical.
For TSO we have to set the TSO and mss bits in the wqe and we only
put the header in the immediate area, no data. Collapse both
functions into write_swqe2_immediate.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch from Michael Ellerman, clean up a significant
portion of the transmit path. There was a lot of duplication here.
Even worse, we were always checksumming tx packets and ignoring the
skb->ip_summed field.
Also remove NETIF_F_FRAGLIST from dev->features, I'm not sure why
it was enabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ehea adapter has a mode where it will avoid partial cacheline DMA
writes on receive by always padding packets to fall on a cacheline
boundary.
Unfortunately we currently aren't allocating enough space for a full
ethernet MTU packet to be rounded up, so this optimisation doesn't hit.
It's unfortunate that the next largest packet size exposed by the
hypervisor interface is 2kB, meaning our skb allocation comes out of a
4kB SLAB. However the performance increase due to this optimisation is
quite large and my TCP stream numbers increase from 900MB to 1000MB/sec.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We weren't enabling any VLAN features so we missed out on checksum
offload and TSO when using VLANs. Enable them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like the ehea xmit routine and an ethtool change of TSO
mode could race, resulting in corrupt packets. Checking gso_size
is enough and we can use the helper function.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_tx_qps module option allows a user to configure a different
number of tx and rx queues. Now the networking stack is multiqueue
aware it makes little sense just to enable the tx queues and not the
rx queues so remove the option.
v3:
[cascardo] fixed conflict with get_stats change
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 18604c5485 (ehea: NAPI multi queue TX/RX path for SMP) added
driver specific logic for exiting napi mode. I'm not sure what it was
trying to solve and it should be up to the network stack to decide when
we are done polling so remove it.
v3:
[cascardo] Fixed extra parentheses.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ehea driver had some multiqueue support but was missing the last
few years of networking stack improvements:
- Use skb_record_rx_queue to record which queue an skb came in on.
- Remove the driver specific netif_queue lock and use the networking
stack transmit lock instead.
- Remove the driver specific transmit queue hashing and use
skb_get_queue_mapping instead.
- Use netif_tx_{start|stop|wake}_queue where appropriate. We can also
remove pr->queue_stopped and just check the queue status directly.
- Print all 16 queues in the ethtool stats.
We now enable multiqueue by default since it is a clear win on all my
testing so far.
v3:
[cascardo] fixed use_mcs parameter description
[cascardo] set ehea_ethtool_stats_keys as const
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deprecated NETIF_F_LLTX feature. Since the network stack
now provides the locking we can remove the driver specific
pr->xmit_lock.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ehea ndo_get_stats can sleep in two places, in a hcall
and in a GFP_KERNEL alloc, which is not correct.
This patch creates a delayed workqueue that grabs the information each 1
sec from the hardware, and place it into the device structure, so that,
.ndo_get_stats quickly returns the device structure statistics block.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*
The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors). In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.
We do not explicitly select the Kconfig dependencies, as this would force
EMAC on. Doing it in the defconfig allows more flexibility.
Tested on a canyondlands board.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the IBM drivers into drivers/net/ethernet/ibm/ and make the
necessary Kconfig and Makefile changes.
- Renamed ibm_new_emac to emac
- Cleaned up Makefile and Kconfig options which referred to
IBM_NEW_EMAC to IBM_EMAC
- ibmlana driver is a National Semiconductor SONIC driver so
it was not moved
CC: Christoph Raisch <raisch@de.ibm.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Gibson <dwg@au1.ibm.com>
CC: Kyle Lucke <klucke@us.ibm.com>
CC: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
