Move devlink_register to be the last command in the initialization
sequence.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink documentation says:
Note that the PHY may be able to transform from one connection
technology to another, so, eg, don't clear 1000BaseX just
because the MAC is unable to BaseX mode. This is more about
clearing unsupported speeds and duplex settings. The port modes
should not be cleared; phylink_set_port_modes() will help with this.
So add the missing 10G modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only struct dim_sample member that does not get
initialized by dim_update_sample() is comp_ctr. (There
is special API to initialize comp_ctr:
dim_update_sample_with_comps(), and it is currently used
only for RDMA.) comp_ctr is used to compute curr_stats->cmps
and curr_stats->cpe_ratio (see dim_calc_stats()) which in
turn are consumed by the rdma_dim_*() API. Therefore,
functionally, the net_dim*() API consumers are not affected.
Nevertheless, fix the computation of statistics based
on an uninitialized variable, even if the mentioned statistics
are not used at the moment.
Fixes: ae0e6a5d16 ("enetc: Add adaptive interrupt coalescing")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strlcpy should not be used because it doesn't limit the source
length. As linus says, it's a completely useless function if you
can't implicitly trust the source string - but that is almost always
why people think they should use it! All in all the BSD function
will lead some potential bugs.
But the strscpy doesn't require reading memory from the src string
beyond the specified "count" bytes, and since the return value is
easier to error-check than strlcpy()'s. In addition, the implementation
is robust to the string changing out from underneath it, unlike the
current strlcpy() implementation.
Thus, We prefer using strscpy instead of strlcpy.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently when probing returns an error, the netdev is freed but
phylink_disconnect is not called.
Create a common function between the unbind path and the error path,
call it the opposite of dpaa2_switch_probe_port: dpaa2_switch_remove_port,
and call it from both the unbind and the error path.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an ASSERT_RTNL in phylink_disconnect_phy which triggers
whenever dpaa2_switch_port_disconnect_mac is called.
To follow the pattern established by dpaa2_eth_disconnect_mac, take the
rtnl_mutex every time we call dpaa2_switch_port_disconnect_mac.
Fixes: 84cba72956 ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dpaa2_switch_takedown has a funny name and does not do the
opposite of dpaa2_switch_init, which makes probing fail when we need to
handle an -EPROBE_DEFER.
A sketch of what dpaa2_switch_init does:
dpsw_open
dpaa2_switch_detect_features
dpsw_reset
for (i = 0; i < ethsw->sw_attr.num_ifs; i++) {
dpsw_if_disable
dpsw_if_set_stp
dpsw_vlan_remove_if_untagged
dpsw_if_set_tci
dpsw_vlan_remove_if
}
dpsw_vlan_remove
alloc_ordered_workqueue
dpsw_fdb_remove
dpaa2_switch_ctrl_if_setup
When dpaa2_switch_takedown is called from the error path of
dpaa2_switch_probe(), the control interface, enabled by
dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled,
because dpaa2_switch_takedown does not call
dpaa2_switch_ctrl_if_teardown.
Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this
means that a second probe of the driver will happen with the control
interface directly enabled.
This will trigger a second error:
[ 93.273528] fsl_dpaa2_switch dpsw.0: dpsw_ctrl_if_set_pools() failed
[ 93.281966] fsl_dpaa2_switch dpsw.0: fsl_mc_driver_probe failed: -13
[ 93.288323] fsl_dpaa2_switch: probe of dpsw.0 failed with error -13
Which if we investigate the /dev/dpaa2_mc_console log, we find out is
caused by:
[E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled
So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in
reasonable limits, no reason to change STP state, re-add VLANs etc), and
rename it to something more conventional, like dpaa2_switch_teardown.
Fixes: 613c0a5810 ("staging: dpaa2-switch: enable the control interface")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The menuconfig FSL_DPAA_ETH selects config FSL_FMAN_MAC, but the config
FSL_FMAN_MAC never existed in the kernel tree.
Hence, ./scripts/checkkconfigsymbols.py warns:
FSL_FMAN_MAC
Referencing files: drivers/net/ethernet/freescale/dpaa/Kconfig
Remove this dead select in menuconfig FSL_DPAA_ETH.
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default FEC driver treat irq[0] (i.e. int0 described in dt-binding) as
wakeup interrupt, but this situation changed on i.MX8M serials, SoC
integration guys mix wakeup interrupt signal into int2 interrupt line.
This patch introduces FEC_QUIRK_WAKEUP_FROM_INT2 to indicate int2 as wakeup
interrupt for i.MX8MQ.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20210812070948.25797-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a switch port is connected to a MAC, use the common dpaa2-mac support
for exporting the available MAC statistics.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patch, we'll add support for also exporting the MAC
statistics in the ethtool stats. Annotate already present HW stats with
a suggestive prefix.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate the common MAC endpoint management support into the
dpaa2-switch driver as well. Nothing special happens here, just that the
already available dpaa2-mac functions are also called from dpaa2-switch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a switch DPAA2 object, the interface ID is also needed when
querying for the object endpoint. Extend fsl_mc_get_endpoint() so that
users can also pass the interface ID that are interested in.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to dpaa2_switch_port_link_state_update is a leftover from the
time when on DPAA2 platforms the PHYs were started at boot time so when
an ifconfig was issued on the associated interface, the link status
needed to be checked directly from the ndo_open() callback. This is not
needed anymore since we are now properly integrated with the PHY layer
thus a link interrupt will come directly from the PHY eventually without
the need to call the sync function.
Fix this up by removing the call to dpaa2_switch_port_link_state_update.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not enable the switch interfaces at probe time since this is
trigged by the open callback. Remove the call dpsw_enable() which does
exactly this.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC firmware supplies us the switch interface index for which an
interrupt was triggered. Use this to our advantage instead of looping
through all the switch ports and doing unnecessary work.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request all interrupt sources to be read and then cleared on the DPSW
object. In the next patches we'll also add support for treating other
interrupts.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch intends to fix MAC internal delay doesn't work, due to use
of_property_read_u32() incorrectly, and improve this feature a bit:
1) check the delay value if valid, only program register when it's 2000ps.
2) only enable "enet_2x_txclk" clock when require MAC internal delay.
Fixes: fc539459e9 ("net: fec: add MAC internal delayed clock feature support")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20210803052424.19008-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate the array faf_bits on the stack but instead it
static const. Makes the object code smaller by 175 bytes.
Before:
text data bss dec hex filename
9645 4552 0 14197 3775 ../freescale/dpaa2/dpaa2-eth-devlink.o
After:
text data bss dec hex filename
9406 4616 0 14022 36c6 ../freescale/dpaa2/dpaa2-eth-devlink.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210801152209.146359-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When mirroring rules are added in shared filter blocks, the same
mirroring rule has to be configured on all the switch ports that are
part of the same block.
In case a switch port joins a shared block after mirroring filters have
been already added to it, then all the mirror rules should be offloaded
to the port. The reverse, removal of mirroring rules, has to be done at
block unbind.
For this purpose, the dpaa2_switch_block_offload_mirror() and
dpaa2_switch_block_unoffload_mirror() functions are added and called
upon binding and unbinding a switch port to/from a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the infrastructure added in the previous patch, extend tc-flower
support with FLOW_ACTION_MIRRED based on VLAN.
Tested with:
tc qdisc add dev eth8 ingress_block 1 clsact
tc filter add block 1 ingress protocol 802.1q flower skip_sw \
vlan_id 100 action mirred egress mirror dev eth6
tc filter del block 1 ingress pref 49152
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per port mirroring for the DPAA2 switch. We support
only single mirror port, therefore we allow mirroring rules only as long
as the destination port is always the same.
Unlike all the actions (drop, redirect, trap) already supported by the
dpaa2-switch driver, adding mirroring filters in shared blocks is not
achieved by a singular ACL entry added in a table shared by the ports.
This is why, when a new mirror filter is added in a block we have to got
through all the switch ports sharing it and configure the filter
individually on all.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary MC API for setting up and configuring the mirroring
feature on the DPSW DPAA2 object.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_matchall_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_flower_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, shared filter blocks were implemented only by ACL tables
shared between ports. Going forward, when the mirroring support will be
added, this will not be true anymore.
Rename the dpaa2_switch_acl_tbl into dpaa2_switch_filter_block so that
we make it clear that the structure is used not only for filters that
use the ACL table but will be used for all the filters that are added in
a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the dpaa2_switch_tc_parse_action() function was used for all
the supported tc actions since all of them were implemented by adding
ACL table entries. In the next commits, the dpaa2-switch driver will
gain mirroring support which is not using the same HW feature.
Make sure that we specify the ACL in the function name so that we make
it clear that it's only used for specific actions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX8QM ENET IP version support timing specification that MAC
integrate clock delay in RGMII mode, the delayed TXC/RXC as an
alternative option to work well with various PHYs.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX8MQ ENET version support IEEE802.3az eee mode, add
eee mode tx lpi enable to support ethtool interface.
usage:
1. set sleep and wake timer to 5ms:
ethtool --set-eee eth0 eee on tx-lpi on tx-timer 5000
2. check the eee mode:
~# ethtool --show-eee eth0
EEE Settings for eth0:
EEE status: enabled - active
Tx LPI: 5000 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
Note: For realtime case and IEEE1588 ptp case, it should disable
EEE mode.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENET of imx8mq and imx8qm are basically the same as imx6sx,
but they have new features support based on imx6sx, like:
- imx8mq: supports IEEE 802.3az EEE standard.
- imx8qm: supports RGMII mode delayed clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any interraction with the buffer pool (seeding a buffer, acquire one) is
made through a software portal (SWP, a DPIO object).
There are circumstances where the dpaa2-switch driver probes on a DPSW
before any DPIO devices have been probed. In this case, seeding of the
buffer pool will lead to a panic since no SWPs are initialized.
To fix this, seed the buffer pool after making sure that the software
portals have been probed and are ready to be used.
Fixes: 0b1b713704 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 4f2673b3a2 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
Make more room for some extra code in the NETDEV_PRECHANGEUPPER handler
by moving what already exists into a dedicated function.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
