Linux maps PAL instructions with an ITR, but uses a DTC for PAL data.
Section 11.10.2.1.3, "Making PAL Procedures Calls in Physical or Virtual
Mode," of the SDM (rev 2.2), says we must therefore make all PAL calls
with PSR.ic = 1 so that Linux can handle any TLB faults.
PAL_CALL_IC_OFF is currently unused, and as long as we use the ITR + DTC
strategy, we can't use it. So remove it. I also removed the code in
ia64_pal_call_static() that conditionally cleared PSR.ic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Allow pending IPIs to interrupt a timer interrupt that is looping
in the do_timer() "while" loop in timer_interrupt(). (Interrupts are
allowed at only 1 spot in the code).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Missed one piece of ia64 fallout from the global IRQ patch
7d12e780e0
Perfmon interrupt handler needs to use get_irq_regs() too.
Acked-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Check for offline nodes in pci NUMA code
[POWERPC] Better check in show_instructions
[POWERPC] POWER6 has 6 PMCs
[POWERPC] Never panic when taking altivec exceptions from userspace
[POWERPC] Fix IO Window Updates on P2P bridges.
[POWERPC] Add Makefile entry for MPC832x_mds support
[POWERPC] Fix MPC8360EMDS PB board support
[POWERPC] ppc: Add missing calls to set_irq_regs
[POWERPC] Off-by-one in /arch/ppc/platforms/mpc8*
[POWERPC] Add DOS partition table support to mpc834x_itx_defconfig
[POWERPC] spufs: fix support for read/write on cntl
[POWERPC] Don't crash on cell with 2 BEs when !CONFIG_NUMA
Introduce desc->name and eliminate the handle_irq_name() hack. Add
set_irq_chip_and_handler_name() to set the flow type and name at once.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid possible PIT livelock issues seen on SMP systems (and reported by
Andi), by not allowing it as a clocksource on SMP boxes.
However, since the PIT may no longer be present, we have to properly handle
the cases where SMP systems have TSC skew and fall back from the TSC.
Since the PIT isn't there, it would "fall back" to the TSC again. So this
changes the jiffies rating to 1, and the TSC-bad rating value to 0.
Thus you will get the following behavior priority on i386 systems:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if UP]
jiffies
Rather then the current more complicated:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if cpus < 4]
tsc [if present & unstable]
jiffies
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.
We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.
It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing entry in Makefile for MPC832x MDS support. It
also change white space to tab in MPC8360 entry.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPC8360EMDS PB support is broken as some code was missing
in last submission. This patch adds missing code and makes
MPC8360EMDS PB support working.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the timer_interrupt we were not calling set_irq_regs() and if we are
profiling we will end up calling get_irq_regs(). This causes bad things to
happen.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(" revealed several
incorrect usages of ARRAY_SIZE in the mpc drivers. The last element in the
array is always ARRAY_SIZE()-1, this patch modifies the bounds checks
accordingly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type. Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a memory leak introduced by "spufs: add support
for read/write oncntl", which was missing a call to simple_attr_close.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on
a non-0 node. This workaround will ignore those SPEs and just print an
message in the kernel log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I need this patch to get a UML kernel to compile. This is with the
kernel headers in FC6 which are automatically generated from the kernel
tree. Some headers are missing but those files don't need them. At
least it appears so since the resuling kernel works fine.
Tested on x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some ARM platforms were still broken as a result of the IRQ register
passing changes, mostly due to a missing linux/irq.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds correct sdram params for K4S281632B-1H and sets the jornada to use them by default.
Signed-off-by: Kristoffer Ericson
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI. We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.
The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise. The attached
patch provides this mechanism.
This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: David Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The new Atmel AT91SAM9261 and AT91SAM9260 processors use a different
internal watchdog peripheral. This watchdog driver is therefore
AT91RM9200-specific.
This patch renames at91_wdt.c to at91rm9200_wdt.c, and changes the name
of the configuration option.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of warning in the thermal throttling code about not checking
sysfs return values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently whoever converted voyager never actually checked that the
patch would compile ...
Remove as much of the pt_regs references as possible and move the
remaining ones into line with what's in x86 generic.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The implementation of genirq in x86 completely broke voyager (and
presumably visws). Since it's plugged into so much of the x86
infrastructure, you can't expect it to work unconverted.
This patch introduces a voyager IRQ handler type and switches voyager
to the genirq infrastructure.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kernel build breaks with CONFIG_X86_VSMP. Probably due to some header
file cleanups in 2.6.19-rc1.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes my one line thinko where I was clearing
the vector_irq entries on the wrong cpus.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix these 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0x3e060) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0x3e064) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0x3e07c) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0x3e080) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'is_ksym_addr' (at offset 0x4b3a4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'is_ksym_addr' (at offset 0x4b3a8) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'is_ksym_addr' (at offset 0x4b3b4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'is_ksym_addr' (at offset 0x4b3e4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b640) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b644) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0x4b654) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0x4b658) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b68c) and 'kallsyms_lookup_size_offset'
The crux of the matter is that modpost only checks the relocatable
sections. i386 vmlinux has none, so modpost does no checking on it (it
does on the modules). However, sparc vmlinux has plenty of
relocatable sections because it is being built with 'ld -r' (to allow
for btfixup processing). So for sparc, modpost does do a lot of
checking. Sure enough, running modpost on arch/sparc/boot/image yields
no output (i.e. all is well).
modpost.c check_sec_ref() has:
/* We want to process only relocation sections and not .init */
if (sechdrs[i].sh_type == SHT_RELA) {
// check here
} else if (sechdrs[i].sh_type == SHT_REL) {
// check here
}
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:sunzilog_console_setup from .data between 'sunzilog_console' (at offset 0x8394) and 'devices_subsys'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix these 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:__alloc_bootmem from .text between 'srmmu_nocache_init' (at offset 0x1a0f8) and 'srmmu_mmu_info'
WARNING: vmlinux - Section mismatch: reference to .init.text:__alloc_bootmem from .text between 'srmmu_nocache_init' (at offset 0x1a118) and 'srmmu_mmu_info'
WARNING: vmlinux - Section mismatch: reference to .init.text:srmmu_early_allocate_ptable_skeleton from .text between 'srmmu_nocache_init' (at offset 0x1a188) and 'srmmu_mmu_info'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill off interrupt_table for all of the CPU subtypes, we now
default in to stepping in to do_IRQ() for _all_ IRQ exceptions
and counting the spurious ones, rather than simply flipping on
the ones we cared about. This and enabling the IRQ by default
automatically has already uncovered a couple of bugs and IRQs
that weren't being caught, as well as some that are being
generated far too often (SCI Tx Data Empty, for example).
The general rationale is to use a marker for interrupt exceptions,
test for it in the handle_exception() path, and skip out to
do_IRQ() if it's found. Everything else follows the same behaviour
of finding the cached EXPEVT value in r2/r2_bank, we just rip out
the INTEVT read from entry.S entirely (except for in the kGDB NMI
case, which is another matter).
Note that while this changes the do_IRQ() semantics regarding r4
handling, they were fundamentally broken anyways (relying entirely
on r2_bank for the cached code). With this, we do the INTEVT read
from do_IRQ() itself (in the CONFIG_CPU_HAS_INTEVT case), or fall
back on r4 for the muxed IRQ number, which should also be closer
to what SH-2 and SH-2A want anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we've started accounting for spurious IRQs, change the
logic somewhat so that we have a better chance of catching them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Pass NULL not 0 for pointer value.
[MIPS] IP27: Make declaration of setup_replication_mask a proper prototype.
[MIPS] BigSur: More useful defconfig.
[MIPS] Cleanup definitions of speed_t and tcflag_t.
[MIPS] Fix compilation warnings in arch/mips/sibyte/bcm1480/smp.c
[MIPS] Optimize and cleanup get_saved_sp, set_saved_sp
[MIPS] <asm/irq.h> does not need pt_regs anymore.
[MIPS] Workaround for bug in gcc -EB / -EL options.
[MIPS] Fix timer setup for Jazz
Certain gcc versions upto gcc 4.1.1 (probably 4.2-subversion as of
2006-10-10 don't properly change the the predefined symbols if -EB / -EL
are used, so we kludge that here. A bug has been filed at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=29413.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
taken exports to actual definitions of symbols being exported.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sun3_ksyms gone, m68k_ksyms trimmed down to exports of the assembler ones,
for sun3 added the missing exports of __ioremap() and iounmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix kernel-doc function name in usercopy.c.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the epoll_pwait system call, that extend the event wait mechanism
with the same logic ppoll and pselect do. The definition of epoll_pwait
is:
int epoll_pwait(int epfd, struct epoll_event *events, int maxevents,
int timeout, const sigset_t *sigmask, size_t sigsetsize);
The difference between the vanilla epoll_wait and epoll_pwait is that the
latter allows the caller to specify a signal mask to be set while waiting
for events. Hence epoll_pwait will wait until either one monitored event,
or an unmasked signal happen. If sigmask is NULL, the epoll_pwait system
call will act exactly like epoll_wait. For the POSIX definition of
pselect, information is available here:
http://www.opengroup.org/onlinepubs/009695399/functions/select.html
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that various memory splits are enabled, add a config option allowing the
user to compile UML for its need - HOST_2G_2G allowed to choose either 3G/1G
or 2G/2G, and enabling it reduced the usable virtual memory.
Detecting this at run time should be implemented in the future, but we must
make the stop-gap measure work well enough (this is valid in _many_ cases).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Deprecate TT mode in Kconfig so that users won't select it, update the
MODE_SKAS description (it was largely obsolete and misleadin) and btw describe
advantages for high memory usage with CONFIG_STATIC_LINK.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The export is together with the definition, in arch/x86_64/lib/csum-partial.c,
which is compiled in by arch/um/sys-x86_64/Makefile.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unify macros common to x86 and x86_64 kernel-offsets.h files.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable compilation of x86_64 crypto code;, and add the needed constant to make
the code compile again (that macro was added to i386 asm-offsets between
2.6.17 and 2.6.18, in 6c2bb98bc3).
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Declare UML partial support for LOCKDEP - however IRQFLAGS tracing requires
some coding which nobody did yet, so we cannot run full lockdep on UML. Grep
for CONFIG_TRACE_IRQFLAGS on i386 code to find their implementation.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On a 64bit Uml, if run under "setarch i386" (which a user did), uname()
currently returns the obtained i686 as machine - fix that. Btw, I'm quite
surprised that under setarch i386 a 64-bit binary can run.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes UML compile on any possible processor choice. The two problems were:
*) x86 code, when 386 is selected, checks at runtime boot_cpuflags, which we do
not have.
*) 3Dnow support for memcpy() et al. does not compile currently and fixing this
is not trivial, so simply disable it; with this change, if one selects MK7
UML compiles (while it did not).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If enable is moved by GCC in a register its value may not be preserved after
coming back there with longjmp(). So, mark it as volatile to prevent this;
this is suggested (it seems) in info gcc, when it talks about -Wuninitialized.
I re-read this and it seems to say something different, but I still believe
this may be needed.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make TT mode compile after the introduction of klibc's implementation of
setjmp.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was forgot in a previous patch so UML does not compile with TT mode
enabled.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct commit 5906e4171a - this makes more
sense: we turn pte_mkexec + pte_wrprotect to pte_mkread. However, due to a
bug in pte_mkread, it does the exact same thing as pte_mkwrite, so this patch
improves the code but does not change anything in practice. The pte_mkread
bug is fixed separately, as it may have big impact.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen pointed out that -mcmodel=kernel does not make sense for userspace
code and would stop everything from working, and pointed out the correct fix
for the original bug (not easy to do for me).
Reverts part of commit 06837504de.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hw_interrupt_type is deprecated in favour of struct irq_chip.
[mingo@elte.hu: do x86_64 too]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns). The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.
The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing. Two users have successfully booted their
powerpcs with it (one an ibook G4). It has also been boot tested on x86,
x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2.
Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix. Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the necessary changes to AVR32 required by the irq regs stuff.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest kernel 2.6.19-rc1 triggers a bug in the s390 specific stack
trace code when compiled with gcc 3.4.
This patch fixes the latest lock dependency validator code (2.6.19-rc1)
on s390 gcc 3.4. The variable sp was fixed to r15 (which is the stack
pointer in the s390 abi) and assigned new values to r15. Therefore,
gcc 3.4 assigns a new value to r15 and does not restore it on exit (r15
is supposed to be call save) - the kernel stack is broken. Avoid trouble
by not assigning any new value to sp (r15).
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the last few places where a pointer to pt_regs gets passed.
Also make sure we call set_irq_regs() before irq_enter() and after
irq_exit(). This doesn't fix anything but makes sure s390 looks the
same like all other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On the old "powersurge" SMP powermacs, the second CPU is started up
by sending it an IPI, which has the side effect of stopping the
timebase clock (so the secondary CPU's timebase can be synchronized
with the primary's). The routine that did this used udelay, which
will hang forever when the timebase is stopped, since udelay now spins
until the timebase reaches a certain value.
The end result is that the kernel would hang when bringing up the
second CPU. This fixes it by using a simple loop which just does a
fixed number of iterations to generate the delay. These old systems
were all clocked at around 200 MHz or so, so a fixed number of
iterations is acceptable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the Maple defconfig to 4 CPUs (along with current defaults)
to support the "tigerwood" 970MP evaluation board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The IDE driver will pick up the PCI IRQ for both channels on Maple
despite the fact that it's in legacy mode. This works around it by
"hiding" the PCI IRQ of the AMD8111 IDE controller when it's configured
in legacy mode on the Maple platform, thus causing the driver to call
pci_get_legacy_ide_irq() which will return the correct interrupts for
both channels.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Maple support code was missing code for U4/CPC945 PCIe. This adds
it, enabling it to work on tigerwood boards, and possibly also js21
using SLOF. Also disable an obsolete firmware workaround.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change CONFIG_PPC_CELL to CONFIG_PPC_IBM_CELL_BLADE in the powerpc boot
makefile.
CONFIG_PPC_CELL is used to build the generic cell processor support, and
is not an indication of platform.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My CROSS_COMPILE is "ccache /opt/compilers/blah", which confuses
the boot wrapper script. Quote CROSS_COMPILE and CROSS32_COMPILE
so they can safely contain spaces.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix these 2.6.19-rc1 build warnings:
CC arch/sparc/kernel/prom.o
arch/sparc/kernel/prom.c: In function `of_set_property':
arch/sparc/kernel/prom.c:246: warning: passing arg 2 of `prom_setprop' discards qualifiers from pointer target type
arch/sparc/kernel/prom.c: In function `build_one_prop':
arch/sparc/kernel/prom.c:446: warning: unused variable `len'
arch/sparc/kernel/prom.c:480: warning: ignoring return value of `prom_getproperty', declared with attribute warn_unused_result
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
They have to be unique system-wide, so use
"NAME@NODE" as the string pattern of the non-root
nodes.
Thanks to Andrew Morton for fixing the error value
checking in bus_add_device() which made this problem
finally noticable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure cpu_has_fpu (which uses smp_processor_id()) is used only in
atomic context.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX49 CPUs have a SYNC instruction so that CONFIG_CPU_HAS_WB is no
longer needed.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make sure that RA on top of interrupt stack is an address of ret_from_irq,
so that dump_stack etc. can trace info interrupted context.
Also this patch fixes except_vec_vi_handler and __smtc_ipi_vector which
seems broken.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only revisions < 4.0 don't have a functional wait instruction.
From Thomas Koeller (Thomas.Koeller@baslerweb.com).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- SERIAL167 is no longer broken
- Removed some unused variables from the driver to fix compiler warnings
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unused arch/m68k/apollo/dma.c, which was obsoleted by the move to the
generic DMA API.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Misc Atari fixes:
- initialize correct number of atari irqs
- silence vbl interrupt until it's used by atafb
- use mdelay() to read clock if necessary
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Due to code bugs or misbehaving hardware it is possible that we can
receive an interrupt that we have not mapped into a linux irq. Calling
BUG when that happens is very rude, and if the problem is mild enough
prevents anything else from getting done.
So instead of calling BUG just scream loudly about the problem and
continue running. We don't have enough knowledge to know which
interrupt triggered this behavior so we don't acknowledge it. This will
likely prevent a recurrence of the problem by jamming up the works with
an unacknowledged interrupt.
If the interrupt was something important it is quite possible that
nothing productive will happen past this point. But it is now at least
possible to keep working if the kernel can survive without the interrupt
we dropped on the floor.
Solutions like irqpoll should generally make dropped irqs non-fatal.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cast to (void *) in request_irq() argument is stupid and
only hides problems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Cleanup unnecessary <asm/ptrace.h> inclusions.
[MIPS] DEC: pt_regs fixes for buserror handlers
[MIPS] Fix return type of gt64120_irq.
[MIPS] Ocelot C: Build fix - ll_mv64340_irq takes no more regs argument.
[MIPS] Jazz defconfig file.
[MIPS] Jazz: build fix - include <linux/screen_info.h>
[MIPS] Jazz: Remove warning. After 7 years probably somebody test this ;)
[MIPS] Jazz: Fix I/O port resources.
[MIPS] DEC: pt_regs fixes for dec_intr_halt.
handle_sysrq lost its pt_regs * argument
Manual conflict resolved in arch/um/drivers/mconsole_kern.c
Real fix for UML pt_regs stuff. Note set_irq_regs() logics in there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 41550c5128.
Quoth Ben Herrenschmidt:
"Please revert this one for now. It seems to break G5s :( Looks like
PCI cells inside Apple IO ASICs don't have a PCI_INTERRUPT_LINE set.
I need to figure out a better fix."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
titan_dispatch_irqs() always gets get_irq_regs() as argument; kill
the argument and collapse set_irq_regs() in body.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
isa_no_iack_sc_device_interrupt() always gets get_irq_regs() as
argument; kill that argument.
All but two callers of handle_irq() pass get_irq_regs() as argument;
convert the remaining two, kill set_irq_regs() inside handle_irq().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
callers of ->device_interrupt() do set_irq_regs() now; pt_regs argument
removed, remaining uses of regs in instances of ->device_interrupt()
are switched to get_irq_regs() and will be gone in the next patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fallout from previous patch:
- actually add include/asm-m68k/irq_regs.h
- missed the prototype of sun3_sched_init()
NB: git diff without argumentgs sucks when you've added
some files...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
read_trylock() is broken on sparc32 (doesn't build and didn't work
right, actually). Proposed fix:
- make "writer holds lock" distinguishable from "reader tries to grab
lock"
- have __raw_read_trylock() try to acquire the mutex (in LSB of lock),
terminating spin if we see that there's writer holding it. Then do
the rest as we do in read_lock().
Thanks to Ingo for discussion...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'irq-fixes' of git://git.parisc-linux.org/git/linux-2.6:
[PARISC] More pt_regs removal
[PARISC] pdc_init no longer exists
[PARISC] Make firmware calls irqsafe-ish...
[PA-RISC] Fix boot breakage
[PARISC] Use set_irq_regs
The problem we can't take advantage of lowest priority delivery mode if
the vectors are allocated for only one cpu at a time. Nor can we work
around hardware that assumes lowest priority delivery mode is always
used with several cpus.
So this patch introduces the concept of a vector_allocation_domain. A
set of cpus that will receive an irq on the same vector. Currently the
code for implementing this is placed in the genapic structure so we can
vary this depending on how we are using the io_apics.
This allows us to restore the previous behaviour of genapic_flat without
removing the benefits of having separate vector allocation for large
machines.
This should also fix the problem report where a hyperthreaded cpu was
receving the irq on the wrong hyperthread when in logical delivery mode
because the previous behaviour is restored.
This patch properly records our allocation of the first 16 irqs to the
first 16 available vectors on all cpus. This should be fine but it may
run into problems with multiple interrupts at the same interrupt level.
Except for some badly maintained comments in the code and the behaviour
of the interrupt allocator I have no real understanding of that problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Which vector an irq is assigned to now varies dynamically and is
not needed outside of io_apic.c. So remove the possibility
of accessing the information outside of io_apic.c and remove
the silly macro that makes looking for users of irq_vector
difficult.
The fact this compiles ensures there aren't any more pieces
of the old CONFIG_PCI_MSI weirdness that I failed to remove.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In commit ace80ab796 I removed the weird
logic that used the vector number as the irq number when MSI was
defined. However pci_enable_irq was using a different test in the
io_apic_assign_irqs path and I missed it :(
This patch removes the wrong code so no one hits this problem.
This code is only active when a specific set of boot command line
parameters is specified which likely explains why no one has notices
this earlier.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, /proc/cpuinfo contains several copies of the information for
whatever processor we happen to be scheduled on. This patch makes it contain
the proper information for each CPU, which is particularly useful on mixed
R12k/R10k IP27 machines.
Signed-off-by: Karl-Johan Karlsson <creideiki@lysator.liu.se>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A kernel built with HZ==250 runs about 4 four times too quickly on a
Cobalt RaQ2.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] PReP fixup after irq changes
[POWERPC] SPU fixup after irq changes
[POWERPC] Fix up after irq changes
[POWERPC] Fix iseries/smp.c for irq breakage
[POWERPC] Fix viocons for irq breakage
[POWERPC] Update iseries_defconfig
[POWERPC] Fix fsl_soc build breaks
[POWERPC] Minor fix for bootargs property
[POWERPC] Update MTFSF_L() comment
[POWERPC] Update pSeries defconfig for SATA
[POWERPC] Don't get PCI IRQ from OF for devices with no IRQ
[POWERPC] Fix zImage decompress location
[POWERPC] linux,tce-size property is 32 bits
[POWERPC] Add DTS for MPC8349E-mITX board
[POWERPC] Fix harmless typo
[PPC] Fix some irq breakage with ARCH=ppc
m68k_handle_int() split in two functions: __m68k_handle_int() takes
pt_regs * and does set_irq_regs(); m68k_handle_int() doesn't get pt_regs
*.
Places where we used to call m68k_handle_int() recursively with the same
pt_regs have simply lost the second argument, the rest is switched to
__m68k_handle_int().
The rest of patch is just dropping pt_regs * where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove struct pt_regs * from all handlers.
Also remove the regs argument from get_irq() functions.
Compile tested with arch/powerpc/config/* and
arch/ppc/configs/prep_defconfig
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove pt_regs from ipi_interrupt and timer_interrupt.
Inline smp_do_timer() into its only caller, and unify the SMP and
non-SMP paths. Fixes a profiling bug.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
There's no reason why we shouldn't be using _irqsave instead of
_irq for any of these calls. fwiw, this fixes the
"start_kernel(): bug: interrupts were enabled early" message displayed
on bootup recently.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Conditionals were the wrong way around. Turns out I was booting the
wrong kernel when testing the original fix.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
This make sure that an iseries_defconfig does not inlude
other platforms.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hrm, there's no way this ever built at time of merge. There's a missing } and
the wrong type on phy_irq.
Also, another const for get_property().
CC arch/powerpc/sysdev/fsl_soc.o
arch/powerpc/sysdev/fsl_soc.c: In function 'fs_enet_of_init':
arch/powerpc/sysdev/fsl_soc.c:625: error: assignment of read-only variable 'phy_irq'
arch/powerpc/sysdev/fsl_soc.c:625: warning: assignment makes integer from pointer without a cast
arch/powerpc/sysdev/fsl_soc.c:661: warning: assignment discards qualifiers from pointer target type
arch/powerpc/sysdev/fsl_soc.c:684: error: subscripted value is neither array nor pointer
arch/powerpc/sysdev/fsl_soc.c:687: error: subscripted value is neither array nor pointer
arch/powerpc/sysdev/fsl_soc.c:722: warning: ISO C90 forbids mixed declarations and code
arch/powerpc/sysdev/fsl_soc.c:728: error: invalid storage class for function 'cpm_uart_of_init'
arch/powerpc/sysdev/fsl_soc.c:798: error: initializer element is not constant
arch/powerpc/sysdev/fsl_soc.c:798: error: expected declaration or statement at end of input
make[1]: *** [arch/powerpc/sysdev/fsl_soc.o] Error 1
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_apic_timer_interrupt() needs to stack the pt_regs* for profile_tick.
If any other of those APIC interrupt handlers want to run get_irq_regs() then
their C entrypoint handlers will need the same treatment.
Cc: Andi Kleen <ak@muc.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the following patch, the ixp4xxdefconfig builds correctly. I'll
test some more configs if I get some time.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Use CONFIG_GENERIC_TIME and define TOD clock source.
[PATCH] sysrq: irq change build fix.
[S390] irq change build fixes.
[S390] cio: 0 is a valid chpid.
[S390] monwriter buffer limit.
[S390] ap bus poll thread priority.
Fixup broken UML build due to 7d12e780e0
"IRQ: Maintain regs pointer globally rather than passing to IRQ handlers".
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo "Blaisorblade" Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
annotate, fix the bogus argument of vmap() in it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jump to the correct exit label after exception
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix too slow clock by using CONFIG_GENERIC_TIME and adding a
clock source for the s390 time-of-day clock. As added benefit
we get rid of the s390 specific definition of do_gettimeofday
and do_settimeofday.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid the use of an uninitialized stack variable when the powerpc device tree
bootargs property is either missing or incorrectly defined. This also makes
CONFIG_CMDLINE work properly under these conditions. This change adds a test
for the existence of the bootargs property.
early_init_dt_scan_chosen() tests for a zero length bootargs property in its
CONFIG_CMDLINE processing, but the current implementation of
of_get_flat_dt_prop() doesn't assign a value to the length when no property is
found. Since an automatic variable is used, a stale value from the stack will
be used in the test.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the ipr driver now supports SATA and depends on libata,
enable libata to get built.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds checking of the PCI_INTERRUPT_PIN register before
using standard OF parsing to retreive PCI interrupts. The reason is
that some PCI devices may have no PCI interrupt, though they may have
interrupts attached via other means. In this case, we shall not use
irq->pdev, but device-specific code can later retreive those interrupts
instead.
Without that patch, Maple and derivatives don't get the right interrupt
for the second IDE channel as the linux IDE code fallsback to the PCI
irq instead of trying to use the legacy ones for the on-board controller
(which has no PCI_INTERRUPT_PIN). Having no PCI IRQ assign to it (as it
doesn't request any) fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The zImage wrapper has a "hack" that force the decompression to happen
above 20Mb for 64 bits kernels, to work around issues with some
firmwares on the field. However, the new wrapper has a bug which makes
that hack not work properly. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The "linux,tce-size" property is only 32 bits (see
prom_initialize_tce_table() in arch/powerpc/kernel/prom_init.c).
Treating it as an unsigned long in iommu_table_setparms() leads to
access beyond the end of the property's buffer, so we pass garbage to
the memset() in that function.
[boot]0020 XICS Init
i8259 legacy interrupt controller initialized
[boot]0021 XICS Done
PID hash table entries: 4096 (order: 12, 32768 bytes)
cpu 0x0: Vector: 300 (Data Access) at [c0000000fe783850]
pc: c000000000035e90: .memset+0x60/0xfc
lr: c000000000044fa4: .iommu_table_setparms+0xb0/0x158
sp: c0000000fe783ad0
msr: 9000000000009032
dar: c000000100000000
dsisr: 42010000
current = 0xc00000000450e810
paca = 0xc000000000411580
pid = 1, comm = swapper
enter ? for help
[link register ] c000000000044fa4 .iommu_table_setparms+0xb0/0x158
[c0000000fe783ad0] c000000000044f4c .iommu_table_setparms+0x58/0x158
(unreliable)
[c0000000fe783b70] c00000000004529c
.iommu_bus_setup_pSeries+0x1c4/0x254
[c0000000fe783c00] c00000000002b8ac .do_bus_setup+0x3c/0xe4
[c0000000fe783c80] c00000000002c924 .pcibios_fixup_bus+0x64/0xd8
[c0000000fe783d00] c0000000001a2d5c .pci_scan_child_bus+0x6c/0x10c
[c0000000fe783da0] c00000000002be28 .scan_phb+0x17c/0x1b4
[c0000000fe783e40] c0000000003cfa00 .pcibios_init+0x58/0x19c
[c0000000fe783ec0] c0000000000094b4 .init+0x1e8/0x3d8
[c0000000fe783f90] c000000000026e54 .kernel_thread+0x4c/0x68
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the DTS for the Freescale MPC 8349E-mITX reference board. Contact
Vitesse for the driver for the VSC 7385.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a problem uncovered by the recent change to always check the
arguments to pr_debug. The sh7751 was using the wrong name for the
PCI IO base address.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At the moment we wrap GENERIC_TIME around our existing timer API.
As boards start providing their own clocksources, they're able to
select GENERIC_TIME accordingly and optimize out most of the timer
API.
Once the current timers have been reworked as proper clocksource
drivers, the rest of the place holders for the timer API can go
away and we can flip on GENERIC_TIME unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix up some of the buildbreaks from the irq handler changes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/~dhowells/irq-2.6:
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
IRQ: Typedef the IRQ handler function type
IRQ: Typedef the IRQ flow handler function type
CONFIG_M386 turns on spinlock-based generic rwsems - which surprises the
semaphore.S rwsem stubs. Tested both with and without CONFIG_M386.
Reported-by: Klaus Knopper <knopper@knopper.net>
Triaged-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
This reverts an earlier patch that was found to cause FPU
state corruption. I think the corruption happens because
unlazy_fpu() can cause FPU exceptions and when it happens
after the current switch some processing would affect
the state in the wrong process.
Thanks to Douglas Crosher and Tom Hughes for testing.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Always make sure RIP/EIP is 0 in the registers stored on the top
of the stack of a kernel thread. This makes sure the unwinder code
won't try a fallback but knows the stack has ended.
AK: this patch is a bit mysterious. in theory they should be terminated
anyways, but it seems to fix at least one crash. Anyways double termination
probably doesn't hurt.
Signed-off-by: Andi Kleen <ak@suse.de>
Make the references to the bus number in hex instead of decimal, as
that is the way that lspci prints out the bus numbers.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Also add copyright for work done after leaving IBM.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The purpose of the code being modified is to determine the location
of the calgary chip address space. This is done by a magical formula
of FE0MB-8MB*OneBasedChassisNumber+1MB*(RioNodeId-ChassisBase) to
find the offset where BIOS puts it. In this formula,
OneBasedChassisNumber corresponds to the NUMA node, and rionodeid is
always 2 or 3 depending on which chip in the system it is. The
problem was that we had an off by one error that caused us to account
some busses to the wrong chip and thus give them the wrong address
space.
Fixes RH bugzilla #203971.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-bu: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
calgary_init's for loop does not correspond to the actual device being
checked, which makes its upperbound check for array overflow useless.
Changing this to a do-while loop is the correct way of doing this.
There should be no possibility of spinning forever in this loop, as
pci_get_device states that it will go through all iterations, then
return NULL (thus breaking the loop).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
do_timer now wants to know how many ticks have elapsed. Now that we
have to calculate that, we can eliminate some of the clever code that
avoided having to calculate that. Also add some more documentation.
I'd like to thank Grant Grundler for helping me with this.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Panic if we can't register the parisc bus or the root parisc device.
There's no way we can boot without them, so let the user know ASAP.
If we can't register a parisc device, handle the failure gracefully.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
The utsname virtualisation broke parisc_newuname compilation.
Rewrite the implementation to call sys_newuname() like sparc64 does.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
max() doesn't like comparing an unsigned long and a resource_size_t,
so make the local variables resource_size_t too.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
When CONFIG_SYSCTL_SYSCALL isn't defined, do_sysctl doesn't exist and
we fail to link. Fix with an ifdef, the same way sparc64 did.
Also add some minor changes to be more like sparc64.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
- Some long constants should be marked 'ul'.
- When using desc->handler_data to pass an __iomem
register area, we need to add casts to and from
__iomem.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This enables support for new firmware test releases.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds defaults for new configuration options added since
2.6.18 and it enables the option for 64kb pages by default.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds an 'object-id' file that the spe library can
use to store a pointer to its ELF object. This was
originally meant for use by oprofile, but is now
also used by the GNU debugger, if available.
In order for oprofile to find the location in an spu-elf
binary where an event counter triggered, we need a way
to identify the binary in the first place.
Unfortunately, that binary itself can be embedded in a
powerpc ELF binary. Since we can assume it is mapped into
the effective address space of the running process,
have that one write the pointer value into a new spufs
file.
When a context switch occurs, pass the user value to
the profiler so that can look at the mapped file (with
some care).
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The properties we used traditionally in the device tree are somewhat
nonstandard. This adds support for a more conventional format using
'interrupts' and 'reg' properties.
The interrupts are specified in three cells (class 0, 1 and 2) and
registered at the interrupt-parent.
The reg property contains either three or four register areas in the
order 'local-store', 'problem', 'priv2', and 'priv1', so the priv1 one
can be left out in case of hypervisor driven systems that access these
through hcalls.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Writing to cntl can be used to stop execution on the
spu and to restart it, reading from cntl gives the
contents of the current status register.
The access is always in ascii, as for most other files.
This was always meant to be there, but we had a little
problem with writing to runctl so it was left out so
far.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Any firmware that still uses the 'spc' nodes already
stopped running for other reasons, so let's get rid of this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since libspe2 will provide a function that can read/write
multiple mailbox elements at once, the kernel should handle
that efficiently.
read/write on the three mailbox files can now access the
spe context multiple times to operate on any number of
mailbox data elements.
If the spu application keeps writing to its outbound
mailbox, the read call will pick up all the data in a
single system call.
Unfortunately, if the user passes an invalid pointer,
we may lose a mailbox element on read, since we can't
put it back. This probably impossible to solve, if the
user also accesses the mailbox through direct register
access.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This hopefully fixes a long-standing bug in the spu file system.
An spu context comes with local memory that can be either saved
in kernel pages or point directly to a physical SPE.
When mapping the physical SPE, that mapping needs to be cache-inhibited.
For simplicity, we used to map the kernel backing memory that way
too, but unfortunately that was not only inefficient, but also incorrect
because the same page could then be accessed simultaneously through
a cacheable and a cache-inhibited mapping, which is not allowed
by the powerpc specification and in our case caused data inconsistency
for which we did a really ugly workaround in user space.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the concept of a gang to spufs as a new type of object.
So far, this has no impact whatsover on scheduling, but makes
it possible to add that later.
A new type of object in spufs is now a spu_gang. It is created
with the spu_create system call with the flags argument set
to SPU_CREATE_GANG (0x2). Inside of a spu_gang, it
is then possible to create spu_context objects, which until
now was only possible at the root of spufs.
There is a new member in struct spu_context pointing to
the spu_gang it belongs to, if any. The spu_gang maintains
a list of spu_context structures that are its children.
This information can then be used in the scheduler in the
future.
There is still a bug that needs to be resolved in this
basic infrastructure regarding the order in which objects
are removed. When the spu_gang file descriptor is closed
before the spu_context descriptors, we leak the dentry
and inode for the gang. Any ideas how to cleanly solve
this are appreciated.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This tries to fix spufs so we have an interface closer to what is
specified in the man page for events returned in the third argument of
spu_run.
Fortunately, libspe has never been using the returned contents of that
register, as they were the same as the return code of spu_run (duh!).
Unlike the specification that we never implemented correctly, we now
require a SPU_CREATE_EVENTS_ENABLED flag passed to spu_create, in
order to get the new behavior. When this flag is not passed, spu_run
will simply ignore the third argument now.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For better explanation, I break down the page fault handling into steps:
1) There is a page fault caused by DMA operation initiated by SPU and
DMA is suspended.
2) The interrupt handler 'spu_irq_class_1()/__spu_trap_data_map()' is
called and it just wakes up the sleeping spe-manager thread.
3) by PPE scheduler, the corresponding bottom half,
spu_irq_class_1_bottom() is called in process context and DMA is
restarted.
There can be a quite large time gap between 2) and 3) and I found
the following problem:
Between 2) and 3) If the context becomes unbound, 3) is not executed
because when the spe-manager thread is awaken, the context is already
saved. (This situation can happen, for example, when a high priority spe
thread newly started in that time gap)
But the actual problem is that the corresponding SPU context does not
work even if it is bound again to a SPU.
Besides I can see the following warning in mambo simulator when the
context becomes
unbound(in save_mfc_cmd()), i.e. when unbind() is called for the
context after step 2) before 3) :
'WARNING: 61392752237: SPE2: MFC_CMD_QUEUE channel count of 15 is
inconsistent with number of available DMA queue entries of 16'
After I go through available documents, I found that the problem is
because the suspended DMA is not restarted when it is bound again.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds NUMA support to the the spufs scheduler.
The new arch/powerpc/platforms/cell/spufs/sched.c is greatly
simplified, in an attempt to reduce complexity while adding
support for NUMA scheduler domains. SPUs are allocated starting
from the calling thread's node, moving to others as supported by
current->cpus_allowed. Preemption is gone as it was buggy, but
should be re-enabled in another patch when stable.
The new arch/powerpc/platforms/cell/spu_base.c maintains idle
lists on a per-node basis, and allows caller to specify which
node(s) an SPU should be allocated from, while passing -1 tells
spu_alloc() that any node is allowed.
Since the patch removes the currently implemented preemptive
scheduling, it is technically a regression, but practically
all users have since migrated to this version, as it is
part of the IBM SDK and the yellowdog distribution, so there
is not much point holding it back while the new preemptive
scheduling patch gets delayed further.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a new "psmap" file to spufs that allows mmap of all of
the problem state mapping of SPEs. It is compatible with 64k pages. In
addition, it removes mmap ability of individual files when using 64k
pages, with the exception of signal1 and signal2 which will both map the
entire 64k page holding both registers. It also removes
CONFIG_SPUFS_MMAP as there is no point in not building mmap support in
spufs.
It goes along a separate patch to libspe implementing usage of that new
file to access problem state registers.
Another patch will follow up to fix races opened up by accessing
the 'runcntl' register directly, which is made possible with this
patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix new restore_sigregs function. It copies the user space copy of the
old psw without correcting the psw.mask and the psw.addr high order bit.
While we are at it, simplify save_sigregs a bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow the board to remap actual USART peripheral devices to serial
devices by calling at32_map_usart(hw_id, serial_line). This ensures
that even though ATSTK1002 uses USART1 as the first serial port, it
will still have a ttyS0 device.
This also adds a board-specific early setup hook and moves the
at32_setup_serial_console() call there from the platform code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the compilation errors on PNX8550 and hard-to-track
bug in interrupt handling.
It also corresponds to the latest changes in PNX8550 serial driver.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
* master.kernel.org:/pub/scm/linux/kernel/git/willy/parisc-2.6: (41 commits)
[PARISC] Kill wall_jiffies use
[PARISC] Honour "panic_on_oops" sysctl
[PARISC] Fix fs/binfmt_som.c
[PARISC] Export clear_user_page to modules
[PARISC] Make DMA routines more stubby
[PARISC] Define pci_get_legacy_ide_irq
[PARISC] Fix CONFIG_DEBUG_SPINLOCK
[PARISC] Fix HPUX compat compile with current GCC
[PARISC] Fix iounmap compile warning
[PARISC] Add support for Quicksilver AGPGART
[PARISC] Move LBA and SBA register defines to the common ropes.h
[PARISC] Create shared <asm/ropes.h> header
[PARISC] Stash the lba_device in its struct device drvdata
[PARISC] Generalize IS_ASTRO et al to take a parisc_device like
[PARISC] Pretty print the name of the lba type on kernel boot
[PARISC] Remove some obsolete comments and I checked that Reo is similar to Ike
[PARISC] Add hardware found in the rp8400
[PARISC] Allow nested interrupts
[PARISC] Further updates to timer_interrupt()
[PARISC] remove halftick and copy clocktick to local var (gcc can optimize usage)
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (25 commits)
[POWERPC] Add support for the mpc832x mds board
[POWERPC] Add initial support for the e300c2 core
[POWERPC] Add MPC8360EMDS default dts file
[POWERPC] Add MPC8360EMDS board support
[POWERPC] Add QUICC Engine (QE) infrastructure
[POWERPC] Add QE device tree node definition
[POWERPC] Don't try to just continue if xmon has no input device
[POWERPC] Fix a printk in pseries_mpic_init_IRQ
[POWERPC] Get default baud rate in udbg_scc
[POWERPC] Fix zImage.coff on oldworld PowerMac
[POWERPC] Fix xmon=off and cleanup xmon initialisation
[POWERPC] Cleanup include/asm-powerpc/xmon.h
[POWERPC] Update swim3 printk after blkdev.h change
[POWERPC] Cell interrupt rework
POWERPC: mpc82xx merge: board-specific/platform stuff(resend)
POWERPC: 8272ads merge to powerpc: common stuff
POWERPC: Added devicetree for mpc8272ads board
[POWERPC] iSeries has no legacy I/O
[POWERPC] implement BEGIN/END_FW_FTR_SECTION
[POWERPC] iSeries does not need pcibios_fixup_resources
...
If you lose the x bit (eg: by using patch(1)), powerpc won't build. Be
defensive about it...
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the declarations for the architecture helpers into
include/linux/htirq.h from the generic include/linux/pci.h. Hopefully this
will make this distinction clearer.
htirq.h is included where it is needed.
The dependency on the msi code is fixed and removed.
The Makefile is tidied up.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is just a few makefile tweaks and some file renames.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out msi_ops was simply not enough to abstract the architecture
specific details of msi. So I have moved the resposibility of constructing
the struct irq_chip to the architectures, and have two architecture specific
functions arch_setup_msi_irq, and arch_teardown_msi_irq.
For simple architectures those functions can do all of the work. For
architectures with platform dependencies they can call into the appropriate
platform code.
With this msi.c is finally free of assuming you have an apic, and this
actually takes less code.
The helpers for the architecture specific code are declared in the linux/msi.h
to keep them separate from the msi functions used by drivers in linux/pci.h
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements two functions ht_create_irq and ht_destroy_irq for
use by drivers. Several other functions are implemented as helpers for
arch specific irq_chip handlers.
The driver for the card I tested this on isn't yet ready to be merged.
However this code is and hypertransport irqs are in use in a few other
places in the kernel. Not that any of this will get merged before 2.6.19
Because the ipath-ht400 is slightly out of spec this code will need to be
generalized to work there.
I think all of the powerpc uses are for a plain interrupt controller in a
chipset so support for native hypertransport devices is a little less
interesting.
However I think this is a half way decent model on how to separate arch
specific and generic helper code, and I think this is a functional model of
how to get the architecture dependencies out of the msi code.
[akpm@osdl.org: Kconfig fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds defines for the hypertransport capability subtypes and starts
using them a little.
[akpm@osdl.org: fix typo]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With more irqs in the system we don't need this.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After raising the number of irqs the system supports this function is no
longer necessary.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This refactors the irq handling code to make the vectors a per cpu resource so
the same vector number can be simultaneously used on multiple cpus for
different irqs.
This should make systems that were hitting limits on the total number of irqs
much more livable.
[akpm@osdl.org: build fix]
[akpm@osdl.org: __target_IO_APIC_irq is unneeded on UP]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a small pessimization but it paves the way for making this information
per cpu. Which allows the the maximum number of IRQS to become NR_CPUS*224.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the change in behavior of the irq allocation code when
CONFIG_PCI_MSI is defined. Removing all instances of the assumption that irq
== vector.
create_irq is rewritten to first allocate a free irq and then to assign that
irq a vector.
assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an
vector not bound to an irq is removed.
The ioapic vector methods are removed, and everything now works with irqs.
The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI
[akpm@osdl.org: cleanup]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the change in behavior of the irq allocation code when
CONFIG_PCI_MSI is defined. Removing all instances of the assumption that irq
== vector.
create_irq is rewritten to first allocate a free irq and then to assign that
irq a vector.
assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an
vector not bound to an irq is removed.
The ioapic vector methods are removed, and everything now works with irqs.
The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes the hardcoded assumption that irq == vector in the msi
composition code, and it allows the msi message composition to setup logical
mode, or lowest priorirty delivery mode as we do for other apic interrupts,
and with the same selection criteria.
Basically this moves the problem of what is in the msi message into the
architecture irq management code where it belongs. Not in a generic layer
that doesn't have enough information to compose msi messages properly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes the hardcoded assumption that irq == vector in the msi
composition code, and it allows the msi message composition to setup logical
mode, or lowest priorirty delivery mode as we do for other apic interrupts,
and with the same selection criteria.
Basically this moves the problem of what is in the msi message into the
architecture irq management code where it belongs. Not in a generic layer
that doesn't have enough information to compose msi messages properly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current implementation of create_irq() is a hack but it is the current
hack that msi.c uses, and unfortunately the ``generic'' apic msi ops depend on
this hack. Thus we are this hack of assuming irq == vector until the
depencencies in the generic irq code are removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current implementation of create_irq() is a hack but it is the current
hack that msi.c uses, and unfortunately the ``generic'' apic msi ops depend on
this hack. Thus we are stuck this hack of assuming irq == vector until the
depencencies in the generic msi code are removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to predict how many irqs we will be able to allocate with
msi using pci_vector_resources and some complicated accounting, and then we
only allow each device as many irqs as we think are available on average.
Only the s2io driver even takes advantage of this feature all other drivers
have a fixed number of irqs they need and bail if they can't get them.
pci_vector_resources is inaccurate if anyone ever frees an irq. The whole
implmentation is racy. The current irq limit policy does not appear to make
sense with current drivers. So I have simplified things. We can revisit this
we we need a more sophisticated policy.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the latest changes the code for migrating x86_64 irqs was dropped. This
reads it in a fashion that will work even if we change the vector on level
triggered irqs when we migrate them.
[akpm@osdl.org: build fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts all the i386 PIC controllers (except VisWS and Voyager,
which I could not test - but which should still work as old-style IRQ layers)
to the new and simpler irq-chip interrupt handling layer.
[akpm@osdl.org: build fix]
[mingo@elte.hu: enable fasteoi handler for i386 level-triggered IO-APIC irqs]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts all the x86_64 PIC controllers layers to the new and
simpler irq-chip interrupt handling layer.
[mingo@elte.hu: The patch also enables the fasteoi handler for x86_64]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wall_jiffies and jiffies are now equal, so this is a noop...
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Joel Soete points out that we refer to pa_tlb_lock but only define it if
CONFIG_SMP which breaks a uniprocessor build with CONFIG_DEBUG_SPINLOCK
enabled. No module refers to pa_tlb_lock, so we can delete the export.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
GCC no longer allows a cast as lvalue; fix the same way fs/readdir.c was
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
iounmap's argument needs to be both const and volatile, otherwise we'll
get warnings that we're discarding pointer qualifiers
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Our prior mode of operation didn't allow nested interrupts
because it makes the interrupt code much simpler. However,
nested interrupts are better for latency.
This code uses the EIEM register to simulate level interrupts
and thus achieve nesting.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This version (relative to the current tree):
o eliminates "while (ticks_elapsed)" loop. It's not needed.
o drop "ticks_elapsed" completely from timer_interrupt().
o Estimates elapsed cycles (based on HZ) to see which kind of
math we want to use to calculate "cycles_remainder".
o Fixes a bug where we would loose a tick if we decided
we wanted to skip one interrupt.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
It's just a bit easier to follow and timer code is complex enough.
So far, only tested on A500-5x (64-bit SMP), ie: gettimeoffset() code
hasn't been tested at all.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
I couldn't find where the itimer was getting started for slave CPUs.
CPU 0 (master) itimer was started in time_init() (arch/parisc/kernel/time.c).
start_cpu_itimer() code was striped from time_init().
Slaves now start their itimer in smp_cpu_init().
This is a first step towards making gettimeoffset() work for SMP.
Next step will be to determine the CR16 (cycle counter)
offsets for each CPU relative to the master (CPU 0).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Stop using PER_LINUX32 to designate processes needing
compaterizing. Convert is_compat_task to use TIF_32BIT and
set TIF_32BIT in binfmt_elf32.c
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch fixes the pa8800 at a gross level (there are still other
subtle incoherency issues which can still cause crashes and HPMCs).
What it does is try to force eject inequivalent aliases before they
become visible to the L2 cache (which is where we get the incoherence
problems).
A new function (parisc_requires_coherency) is introduced in
asm/processor.h to identify the pa8x00 processors (8800 and 8900)
which have the issue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Abstract existing shift register left macros as shift register
right are. This lends itself to a nice clean up of some #ifdef
blocks in entry.S
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
