The R-Car H2 and M2 SoCs come with an xHCI controller that requires
some specific initializations related to the firmware downloading and
some specific registers. This patch adds the support for this special
configuration as an xHCI quirk executed during probe and start.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: "mathias.nyman@intel.com" <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the use of managed interface devm_ioremap_resource
for ioremap_nocache and request_mem_region and removes the corresponding
free functions in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
grep must work, not matter the line length.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove the function klsi_105_tiocmset which was only
returning -EINVAL. It also removes the function prototype and
the .tiocmset entry in the struct usb_serial_driver.
Verified by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
describe the mechanisms for controlling port power policy and
discovering the port power state.
[oliver]: fixes, clarification of wakeup vs port-power-control
[sarah]: wordsmithing
[djbw]: updates for peer port changes
[alan]: review and fixes
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resuming a powered down port sometimes results in the port state being
stuck in the training sequence.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
port1: can't get reconnection after setting port power on, status -110
hub 3-0:1.0: port 1 status 0000.02e0 after resume, -19
usb 3-1: can't resume, status -19
hub 3-0:1.0: logical disconnect on port 1
In the case above we wait for the port re-connect timeout of 2 seconds
and observe that the port status is USB_SS_PORT_LS_POLLING (although it
is likely toggling between this state and USB_SS_PORT_LS_RX_DETECT).
This is indicative of a case where the device is failing to progress the
link training state machine.
It is resolved by issuing a warm reset to get the hub and device link
state machines back in sync.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
usb usb3: port1 usb_port_runtime_resume requires warm reset
hub 3-0:1.0: port 1 not warm reset yet, waiting 50ms
usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
After a reconnect timeout when we expect the device to be present, force
a warm reset of the device. Note that we can not simply look at the
link status to determine if a warm reset is required as any of the
training states USB_SS_PORT_LS_POLLING, USB_SS_PORT_LS_RX_DETECT, or
USB_SS_PORT_LS_COMP_MOD are valid states that do not indicate the need
for warm reset by themselves.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Ksenia Ragiadakou <burzalodowa@gmail.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sunil Joshi <joshi@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is disconnected, usb_unbind_interface is called, which
tries to enable and disable LPM. usb_enable_lpm also try to send a
control command SET SEL to the device.
Since device is already disconnected, therefore it does not make sense
to execute usb_(en/dis)able_lpm.
This patch returns from usb_(en/dis)able_lpm, if device was not in
default state atleast.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All dwc3 based xhci host controller supports USB3.0 LPM functionality.
Therefore enable it in platform data for all dwc3 based xhci device if
DWC3_HOST_USB3_LPM_ENABLE is selected in Kconfig.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use auto U0-U1/U2 transition by xhci platform device add
(en/dis)able_usb3_lpm_timeout function to the xhci_plat_xhci_driver struct.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As best case, a host controller should support U0 to U1 switching for
the devices connected below any tier of hub level supported by usb
specification. Therefore xhci_check_tier_policy should always return
success as default implementation.
A host should be able to issue LGO_Ux after the timeout calculated as
per definition of system exit latency defined in C.1.5.2. Therefore
xhci_calculate_ux_timeout returns ux_params.sel as the default
implementation.
Use default calculation in absence of any vendor specific limitations.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'err' is uninitialized, rather print the error code directly.
This also fixes following warning.
drivers/usb/misc/usb3503.c: In function ‘usb3503_probe’:
drivers/usb/misc/usb3503.c:195:11: warning: ‘err’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
dev_err(dev, "unable to request refclk (%d)\n", err);
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Important bug fix for parsing 64-bit addresses on 32-bit platforms.
Without this patch the kernel will try to use memory ranges that cannot
be reached.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7+H1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bugfix from Grant Likely:
"Important bug fix for parsing 64-bit addresses on 32-bit platforms.
Without this patch the kernel will try to use memory ranges that
cannot be reached"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch
This is a set of 13 fixes, a MAINTAINERS update and a sparse update. The
fixes are mostly correct value initialisations, avoiding NULL derefs and some
uninitialised pointer avoidance.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTuNEhAAoJEDeqqVYsXL0MYC4H/2gpxHA9rELiqPRLJGNjt9v3
YlGrIwVAAdYLBSgwtkpAYj6oDJtwRmZvP3Saj2n5Lga+32mgFsPjvy+JsM3O41SL
k5QRlAs10wMbOB/dSoGxFsKdGnig4NolCIe5p0MGQvAbcCvh9z2Tr876ssvSfMCh
1mh0xmTCIutD7R2f5WjRckA+HZo+qmLLz5ZyogDasI3mSRAHjcZ+j5HdWBQbEsag
U6lPDR5VpUjGpigwJ+BPWwKTbIAIW1v2TB1YjWSHr5h2QPLBa+hfbyc15S1AjsGb
9F5/L432yk4UXQUKyKIpCKi8rDCoioM8dt8ofjjTNfNNjDlYRRHKutalef1yOw8=
=HPXQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
Pull drm fixes from Dave Airlie:
"i915, tda998x and vmwgfx fixes,
The main one is i915 fix for missing VGA connectors, along with some
fixes for the tda998x from Russell fixing some modesetting problems.
(still on holidays, but got a spare moment to find these)"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
- Reset fix for am43xx
- Proper OPP table for omap5
- Fix for SoC detection of one of the DRA7 SoCs
- hwmod updates to get SATA and OCP to work on omap5 (drivers merged in 3.16)
- ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was removed in
anticipation of a watchdog driver being merged for 3.16, and it didn't make
it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this point
but it slipped through cracks repeatedly while coming up the maintainer
chain and only affects the one SoC so risk is low.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=J9xD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
* Reset fix for am43xx
* Proper OPP table for omap5
* Fix for SoC detection of one of the DRA7 SoCs
* hwmod updates to get SATA and OCP to work on omap5 (drivers
merged in 3.16)
* ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was
removed in anticipation of a watchdog driver being merged for 3.16,
and it didn't make it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this
point but it slipped through cracks repeatedly while coming up the
maintainer chain and only affects the one SoC so risk is low"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add few more Keystone drivers
MAINTAINERS: merge MXS entry into IMX one
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
ARM: bcm: Fix bcm and multi_v7 defconfigs
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Pull irq fixes from Thomas Gleixner:
"A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
which I introduced in the last round of cleanups :("
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix memory leak when calling irq_free_hwirqs()
irqchip: spear_shirq: Fix interrupt offset
irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
irqchip: armada-370-xp: Mask all interrupts during initialization.
Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.
* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
irq_free_hwirqs() always calls irq_free_descs() with a cnt == 0
which makes it a no-op since the interrupt count to free is
decremented in itself.
Fixes: 7b6ef12625
Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1404167084-8070-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Update MAINTAINERS file for recently added reset controller, AEMIF
and clocksource driver for Keystone SOCs.
The EMIF memory controller driver is also added along with AEMIF.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The mach-mxs platform is actually co-maintained by myself and
pengutronix folks. Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=eDSn
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.16 (round #2)
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
This partly reverts commits 553600502b (ARM: sunxi: Remove reset code from
the platform) and 5e669ec583 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.
This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2HDE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=wZau
-----END PGP SIGNATURE-----
Merge tag 'md/3.16-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Two minor bugfixes for md in 3.16"
* tag 'md/3.16-fixes' of git://neil.brown.name/md:
md: flush writes before starting a recovery.
md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status
This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zvT1
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
Pull btrfs fixes from Chris Mason:
"We've queued up a few fixes in my for-linus branch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix crash when starting transaction
Btrfs: fix btrfs_print_leaf for skinny metadata
Btrfs: fix race of using total_bytes_pinned
btrfs: use E2BIG instead of EIO if compression does not help
btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
Btrfs: fix use-after-free when cloning a trailing file hole
btrfs: fix null pointer dereference in btrfs_show_devname when name is null
btrfs: fix null pointer dereference in clone_fs_devices when name is null
btrfs: fix nossd and ssd_spread mount option regression
Btrfs: fix race between balance recovery and root deletion
Btrfs: atomically set inode->i_flags in btrfs_update_iflags
btrfs: only unlock block in verify_parent_transid if we locked it
Btrfs: assert send doesn't attempt to start transactions
btrfs compression: reuse recently used workspace
Btrfs: fix crash when mounting raid5 btrfs with missing disks
btrfs: create sprout should rename fsid on the sysfs as well
btrfs: dev replace should replace the sysfs entry
btrfs: dev add should add its sysfs entry
btrfs: dev delete should remove sysfs entry
btrfs: rename add_device_membership to btrfs_kobj_add_device
The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.
It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: fixed arch/arm64/kernel/efi-entry.S]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org>
Tested-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # v3.11+
The define ARM64_64K_PAGES is tested for rather than
CONFIG_ARM64_64K_PAGES. Correct that typo here.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here's a round of USB bugfixes, quirk additions, and new device ids for
3.16-rc4. Nothing major in here at all, just a bunch of tiny changes.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlO1+wwACgkQMUfUDdst+ylcuACfbIytKMfxNcmq2xG6AExXbVSl
IQAAnAvv4QjqzbtSVWaNZB/Kkxzh4xeN
=Igpa
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...
Nothing major here, just 4 small bugfixes that resolve some issues
reported for the IIO (staging and non-staging) and the tidspbridge
driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlO1+gYACgkQMUfUDdst+ylqPgCdGlfPLOaFYI/IlOUDbdAG7YRP
QCIAn0U3wnG4QjVAwmzCHlcPAtFt4un9
=kDww
-----END PGP SIGNATURE-----
Merge tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg KH:
"Nothing major here, just 4 small bugfixes that resolve some issues
reported for the IIO (staging and non-staging) and the tidspbridge
driver"
* tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: tidspbridge: fix an erroneous removal of parentheses
iio: of_iio_channel_get_by_name() returns non-null pointers for error legs
staging: iio/ad7291: fix error code in ad7291_probe()
iio:adc:ad799x: Fix reading and writing of event values, apply shift
Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlO1/FEACgkQMUfUDdst+ynRPACfWcssJKICc2N7g9/0XXGVTjVT
PwwAnjQ8bjOfu6i2z/lViLtZGjOnzKor
=qtjB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows"
* tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
kernfs: kernfs_notify() must be useable from non-sleepable contexts
running:
# perf probe -x /lib/libc.so.6 syscall
# echo 1 >> /sys/kernel/debug/tracing/events/probe_libc/enable
# perf record -e probe_libc:syscall whatever
kills the uprobe. Along the way he found some other minor bugs and clean ups
that he fixed up making it a total of 4 patches.
Doing unrelated work, I found that the reading of the ftrace trace
file disables all function tracer callbacks. This was fine when ftrace
was the only user, but now that it's used by perf and kprobes, this
is a bug where reading trace can disable kprobes and perf. A very unexpected
side effect and should be fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTtMugAAoJEKQekfcNnQGuRs8H/2HhNAy0F1pAFYT5tH2o0z/Z
z6NFn83FUUoesg/Bd+1Dk7VekIZIdo1JxQc67/Y0D0oylPPr31gmVvk2llFPdJV5
xuWiUOuMbDq4Eh3Een8yaOsNsGbcX0lgw9qJEyqAvhJMi5G4dyt3r/g+vFThAyqm
O8Uv74GBGmUmmGMyZuW2r2f2vSEANSXTLbzFqj54fV7FNms1B0MpZ/2AiRcEwCzi
9yMainwrO1VPVSrSJFkW8g4sNl5X1M4tiIT8wGN75YePJVK3FAH8LmUDfpau4+ae
/QGdjNkRDWpZ3mMJPbz3sAT7USnMlSZ5w80Rf/CZuZAe2Ncycvh9AhqcFV0+fj8=
=3h4s
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg Nesterov found and fixed a bug in the perf/ftrace/uprobes code
where running:
# perf probe -x /lib/libc.so.6 syscall
# echo 1 >> /sys/kernel/debug/tracing/events/probe_libc/enable
# perf record -e probe_libc:syscall whatever
kills the uprobe. Along the way he found some other minor bugs and
clean ups that he fixed up making it a total of 4 patches.
Doing unrelated work, I found that the reading of the ftrace trace
file disables all function tracer callbacks. This was fine when
ftrace was the only user, but now that it's used by perf and kprobes,
this is a bug where reading trace can disable kprobes and perf. A
very unexpected side effect and should be fixed"
* tag 'trace-fixes-v3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove ftrace_stop/start() from reading the trace file
tracing/uprobes: Fix the usage of uprobe_buffer_enable() in probe_event_enable()
tracing/uprobes: Kill the bogus UPROBE_HANDLER_REMOVE code in uprobe_dispatcher()
uprobes: Change unregister/apply to WARN() if uprobe/consumer is gone
tracing/uprobes: Revert "Support mix of ftrace and perf"
Pull kbuild fix from Michal Marek:
"There is one more fix for the relative paths series from -rc1: Print
the path to the build directory at the start of the build, so that
editors and IDEs can match the relative paths to source files"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Print the name of the build directory
Pull nfsd bugfixes from Bruce Fields:
"By coincidence, two NFSv4 symlink bugs, one introduced in the 3.16 xdr
encoding rewrite, the other a decoding bug that I think we've had
since the start but that just doesn't trigger very often"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
nfs: fix nfs4d readlink truncated packet
nfsd: fix rare symlink decoding bug
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan points out that I forgot to make the needed fixes to the
lz4_uncompress_unknownoutputsize() function to mirror the changes done
in lz4_decompress() with regards to potential pointer overflows.
The only in-kernel user of this function is the zram code, which only
takes data from a valid compressed buffer that it made itself, so it's
not a big issue. But due to external kernel modules using this
function, it's better to be safe here.
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: "Don A. Bailey" <donb@securitymouse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8846bab180 introduced a helper that can be used to query the
wire transfer size for a SCSI command taking protection information into
account.
However, some commands do not have a 1:1 mapping between the block range
they work on and the payload size (discard, write same). After the
scatterlist has been set up these requests use __data_len to store the
number of bytes to report completion on. This means that callers of
scsi_transfer_length() would get the wrong byte count for these types of
requests.
To overcome this we make scsi_transfer_length() use the scatterlist
length in the scsi_data_buffer as basis for the wire transfer
calculation instead of __data_len.
Reported-by: Christoph Hellwig <hch@infradead.org>
Debugged-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Fixes: d77e65350f
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Merge fixes from Andrew Morton:
"14 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
shmem: fix init_page_accessed use to stop !PageLRU bug
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
fs/seq_file: fallback to vmalloc allocation
/proc/stat: convert to single_open_size()
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
msync: fix incorrect fstart calculation
zram: revalidate disk after capacity change
tools: memory-hotplug fix unexpected operator error
tools: cpu-hotplug fix unexpected operator error
autofs4: fix false positive compile error
slub: fix off by one in number of slab tests
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
Under shmem swapping load, I sometimes hit the VM_BUG_ON_PAGE(!PageLRU)
in isolate_lru_pages() at mm/vmscan.c:1281!
Commit 2457aec637 ("mm: non-atomically mark page accessed during page
cache allocation where possible") looks like interrupted work-in-progress.
mm/filemap.c's call to init_page_accessed() is fine, but not mm/shmem.c's
- shmem_write_begin() is clearly wrong to use it after shmem_getpage(),
when the page is always visible in radix_tree, and often already on LRU.
Revert change to shmem_write_begin(), and use init_page_accessed() or
mark_page_accessed() appropriately for SGP_WRITE in shmem_getpage_gfp().
SGP_WRITE also covers shmem_symlink(), which did not mark_page_accessed()
before; but since many other filesystems use [__]page_symlink(), which did
and does mark the page accessed, consider this as rectifying an oversight.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 939f04bec1 ("printk: enable interrupts before calling
console_trylock_for_printk()").
Andreas reported:
: None of the post 3.15 kernel boot for me. They all hang at the GRUB
: screen telling me it loaded and started the kernel, but the kernel
: itself stops before it prints anything (or even replaces the GRUB
: background graphics).
939f04bec1 is modest latency reduction. Revert it until we understand
the reason for these failures.
Reported-by: Andreas Bombe <aeb@debian.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
