The computation of the first-level watermarks for g4x and gen5+ are
based on the same algorithm, so we can refactor those code paths to
use a single function.
Note that g4x_compute_wm0 takes a 'plane' argument while
ironlake_compute_wm0 took a 'pipe' argument. Both should have used a
'plane' argument, so this patch fixes that as well (not that it caused
a problem; ironlake always uses pipe == plane).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
During the refactoring in revision 6067aaeadb,
the intel_enable_clock_gating was split up into several functions that are
then called indirectly. However, which function to call was not specified for
the IS_PINEVIEW() case. This patch specifies the correct gating function.
Signed-off-by: Jason Stubbs <jasonbstubbs@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
* 'keithp/drm-intel-next' of ../drm-next:
drm/i915: initialize gen6 rps work queue on Sandy Bridge and Ivy Bridge
drm/i915/sdvo: Reorder i2c initialisation before ddc proxy
drm/i915: FDI link training broken on Ironlake by Ivybridge integration
drm/i915: enable rc6 by default
drm/i915: add fbc enable flag, but disable by default
drm/i915: clean up unused ring_get_irq/ring_put_irq functions
drm/i915: fix user irq miss in BSD ring on g4x
Commit 357555c00f split out IVB-specific
register definitions for FDI link training, but a piece of that commit
stopped executing some critical code on Ironlake systems while leaving
it running on Sandybridge.
Turn that code back on both Ironlake and Sandybridge
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
FBC has too many corner cases that we don't currently deal with, so
disable it by default so we can enable more important features like RC6,
which conflicts in some configurations.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31742
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'keithp/drm-intel-next' of /ssd/git/drm-next: (301 commits)
drm/i915: split PCH clock gating init
drm/i915: add Ivybridge clock gating init function
drm/i915: Update the location of the ringbuffers' HWS_PGA registers for IVB.
drm/i915: Add support for fence registers on Ivybridge.
drm/i915: Use existing function instead of open-coding fence reg clear.
drm/i915: split clock gating init into per-chipset functions
drm/i915: set IBX pch type explicitly
drm/i915: add Ivy Bridge PCI IDs and driver feature structs
drm/i915: add PantherPoint PCH ID
agp/intel: add Ivy Bridge support
drm/i915: ring support for Ivy Bridge
drm/i915: page flip support for Ivy Bridge
drm/i915: interrupt & vblank support for Ivy Bridge
drm/i915: treat Ivy Bridge watermarks like Sandy Bridge
drm/i915: manual FDI training for Ivy Bridge
drm/i915: add swizzle/tiling support for Ivy Bridge
drm/i915: Ivy Bridge has split display and pipe control
drm/i915: add IS_IVYBRIDGE macro for checks
drm/i915: add IS_GEN7 macro to cover Ivy Bridge and later
drm/i915: split enable/disable vblank code into chipset specific functions
...
Ibex Peak and CougarPoint already require a different setting (added
here), and future chips will likely follow that precedent.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Some of the bits have changed, including one we were setting that enables
a VGA test mode, preventing pipe B from working at all. So add a new
IVB specific function with the right bits.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This helps contain the mess to init_display() instead.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Treat Ivy Bridge like previous chips as far as flip submission is
concerned.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Not fully tested.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
A0 stepping chips need to use manual training, but the bits have all
moved. So fix things up so we can at least train FDI for VGA links.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Rather than branching in ironlake_pch_enable, add a new train_fdi
function to the display function pointer struct and use it instead.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit 49183b2818.
Quoth Franz Melchior:
"This patch introduces a bug on my infamous "Acer Travelmate
5735Z-452G32Mnss": when KMS takes over, the frame buffer contents get
completely garbled up on screen, with colored stripes and unreadable
text (photo on request). Only when X11 is started, the screen gets
restored again. Closing and re-opening the lid partly cures the
mess, too: it makes the font readable, though horizontally stretched."
Acked-by: Keith Packard <keithp@keithp.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The render P-state handling code requires reading from a GT register.
This means that FORCEWAKE must be written to, a resource which is shared
and should be protected by struct_mutex. Hence we can not manipulate
that register from within the interrupt handling and so must delegate
the task to a workqueue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Found by the new strict checking for the mutex being held whilst
manipulating the forcewake status.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Provide a reference count to track the forcewake state of the GPU and
give a safe mechanism for userspace to wake the GT. This also potentially
saves a UC read if the GT is known to be awake already.
The reference count is atomic, but the register access and hardware wake
sequence is protected by struct_mutex.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the outputs are active and continuing to access the GATT when we
teardown the PTEs, then there is a potential for us to hang the GPU.
The hang tends to be a PGTBL_ER with either an invalid host access or
an invalid display plane fetch.
v2: Reorder IRQ initialisation to defer until after GEM is setup.
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> (855GM)
Tested-by: Pekka Enberg <penberg@kernel.org>
# note that this doesn't fix the underlying problem of the
PGTBL_ER and pipe underruns being reported immediately upon
init on his 965GM MacBook
Reported-and-tested-by: Rick Bramley <richard.bramley@hp.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35635
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36048
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
For debug & testing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a race condition between setting PWRCTXA and executing
MI_SET_CONTEXT. PWRCTXA must not be set until a valid context has been
written (or else the GPU could possible go into rc6, and return to an
invalid context).
Reported-and-Tested-by: Gu Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
In the failure cases during rc6 initialization, both the power context
and render context may get !refcount without holding struct_mutex.
However, on rc6 disabling, the lock is held by the caller.
Rearranged the locking so that it's safe in both cases.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
They're used in one place, and not providing any descriptive value,
with their names just being approximately the conjunction of the
struct name and the struct field.
This diff was produced with gcc -E, copying the new struct definitions
out, moving a couple of the old comments into place in the new
structs, and reindenting.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We used to have these from the product of (pch, non-pch) * (pipe a,
pipe b). Now we can just use the nice per-pipe reg macros in the
split out crtc_mode_sets.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While g4x had DP, eDP came with Ironlake, so we don't need that code here.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This path, which shouldn't be *that* complicated, is now so littered
with per-chipset tweaks that it's hard to trace the order of what
happens. HAS_PCH_SPLIT() is the most radical change across chipsets,
so it seems like a natural split to simplify the code.
This first commit just copies the existing code without changing
anything.
v2: updated to track removal of call to intel_enable_plane from i9xx_crtc_mode_set
Signed-off-by: Eric Anholt <eric@anholt.net>
Hella-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to ensure that we feed valid memory into the display plane
attached to the pipe when switching the pipe on. Otherwise, the display
engine may read through an invalid PTE and so throw an PGTBL_ER
exception.
As we need to perform load detection before even the first object is
allocated for the fbdev, there is no pre-existing object large enough
for us to borrow to use as the framebuffer. So we need to create one
and cleanup afterwards. At other times, the current fbcon may be large
enough for us to borrow it for duration of load detection.
Found by assert_fb_bound_for_plane().
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we now never attempt to steal a crtc for load detection, we either
set a mode on a new pipe, or change the dpms mode on an existing pipe.
Never both, so we can simplify the code slightly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we only allow the use of a disabled CRTC, we don't need to handle the
case where we are reusing an already enabled pipe.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and the no longer relevant comment. The code ceased stealing a pipe
for load detection a long time ago.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Check the return value from drm_crtc_set_mode(), report the failure
via a debug message and propagate the error back to the caller. This
prevents us from blissfully continuing to do the load detection on a
disabled pipe. Fortunately actual failure for modesetting is very rare,
and reported failures even rarer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Despite the fixes in 548f245ba6 (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in 9db4a9c (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...
Found by assert_fb_bound_for_plane().
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Add __attribute__((format (printf, 4, 5))) to drm_ut_debug_printk
and fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.
Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Similar to booting, we need to inspect the state left by the BIOS and
remove any conflicting bits before we take over. The example reported by
Seth Forshee is very similar to the bug we encountered with the state left
by grub2, that the crtc pipe<->planning mapping was reversed from our
expectations and so we failed to turn off the outputs when booting or,
in this case, resuming. This may be in fact the same bug, but triggered
at resume time.
This patch rearranges the code we already have to clear up the
conflicting state upon init and calls it from reset (which is called
after we have lost control of the hardware, i.e. along both the boot and
resume paths) instead.
Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35796
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Fix up the debug file to report the right frequencies. On SNB, we program
the PCU with a frequency ratio, which is multiplied by 100MHz on the CPU
side. But GFX only runs at half that, so report it as such to avoid
confusion.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
A broken implementation of is_pot() prevented the detection of when a
singular pipe was enabled. Eric Anholt pointed out the existence of
is_power_of_2() so use that instead of our broken code!
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35402
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Tested-by: xunx.fang@intel.com
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the pipe or plane is already enabled, then we do not need to enable
it again and can skip the delay. Similarly if it is already disabled
when we want to disable it, we can also skip it.
This fixes a regression from b24e717988, which caused the LVDS
output on one PineView machine to become corrupt after changing
orientation several times.
References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Tested-by: mengmeng.meng@intel.com
... as wait_for_vblank (and friends) will do a flush of the MMIO writes
anyway.
References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
