The baseboard has a connector for a pulse density microphone.
This is connected via the micfil interface and uses the DMIC
audio codec with the simple-audio-card.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The baseboard has a connector for a pulse density microphone.
This is connected via the micfil interface and uses the DMIC
audio codec with the simple-audio-card.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The baseboard has a connector for a pulse density microphone.
This is connected via the micfil interface and uses the DMIC
audio codec with the simple-audio-card.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of using a custom glue layer connecting the wm8962 CODEC
to the SAI3 sound-dai, migrate the sound card to simple-audio-card.
This also brings this board in line with the imx8mn-beacon and
imx8mp-beacon.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per wlf,wm8524.yaml, 'clocks' and 'clock-names' are not valid
properties.
Remove them to fix the following schema warning:
audio-codec: Unevaluated properties are not allowed ('clock-names', 'clocks' were unexpected)
from schema $id: http://devicetree.org/schemas/sound/wlf,wm8524.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a I2C controlled 100MHz Reference clock used by the PCIe
controller. Configure this clock's DIF1 output to be used by
the PCIe.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per the DT bindings, the micfil node should have a sound-dai-cells
entry.
Fixes: cca69ef6eb ("arm64: dts: imx8mn: Add support for micfil")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per the DT bindings, the micfil node should have a sound-dai-cells
entry.
Fixes: 3bd0788c43 ("arm64: dts: imx8mm: Add support for micfil")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for TQMLS1088A SOM on MBLS10xxA baseboard.
Signed-off-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the TQMLS1043A and TQMLS1046A SOM and the
MBLS10xxA baseboard. TQMLS1043A and TQMLS1046A share a common layout
and can be used on the MBLS10xxA.
Signed-off-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the documentation the ls1043a has only one spi controller.
So remove the second one.
Signed-off-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the SolidRun LX2162A System on Module (SoM), and the
Clearfog evaluation board.
The SoM has few software-controllable features:
- AR8035 Ethernet PHY
- eMMC
- SPI Flash
- fan controller
- various eeproms
The Clearfog evaluation board provides:
- microSD connector
- USB-A
- 2x 10Gbps SFP+
- 2x 25Gbps SFP+ with a retimer
- 8x 2.5Gbps RJ45
- 2x mPCI (assembly option / disables 2xRJ45)
The 8x RJ45 ports are connected with an 8-port PHY: Marvell 88E2580
supporting up to 5Gbps, while SoC and magnetics are limited to 2.5Gbps.
However 2500 speed is untested due to documentation and drivier
limitations. To avoid confusion the phy nodes have been explicitly
limited to 1000 for now.
The PCI nodes are disabled, but explicitly added to mark that this board
can have pci.
It is expected that the bootloader will patch the status property
"okay" and disable 2x RJ45 ports, according to active serdes configuration.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add description for the LX2160A second SerDes block.
It is functionally identical to the first one already added in
commit 3cbe93a1f5 ("arch: arm64: dts: lx2160a: describe the SerDes
block #1").
The SerDes driver currently updates the registers of all 8 lanes by
default during probe. Because currently this driver only supports
configuration of network protocols, this can lead to problems with
certain configurations.
Set status property to "disabled" by default so that existing boards are
not impacted.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per binding doc, i.MX93 GPIO supports two interrupts and one register
base, compatible with i.MX8ULP. The current fsl,imx7ulp-gpio compatible
could work for i.MX93 in gpio-vf610.c driver, it is based on the base
address are splited into two with offset added in device tree node.
Now following hardware design, using one register base in device tree node.
This may break users who use compatible fsl,imx7ulp-gpio to enable
i.MX93 GPIO.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8ULP GPIO supports two interrupts and one register base,
the current fsl,imx7ulp-gpio compatible could work for i.MX8ULP in
gpio-vf610.c driver, it is based on the base address are splited
into two with offset added in device tree node. Now following
hardware design, using one register base in device tree node.
This may break users who use compatible fsl,imx7ulp-gpio to enable
i.MX8ULP GPIO.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The valid compatible string for the tps65132 regulator
is "ti,tps65132".
Change it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SAI2_TXC pin is left unconnected per the imx8mp-debix-model-a
schematics:
https://debix.io/Uploads/Temp/file/20230331/DEBIX%20Model%20A%20Schematics.pdf
Also, the RTS5411E USB hub chip does not have a reset pin.
Remove this pin description to properly describe the hardware.
This also fixes the following schema warning:
hub@1: 'reset-gpios' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/realtek,rts5411.yaml#
Fixes: 0253e1cb63 ("arm64: dts: imx8mp-debix: add USB host support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per ethernet-phy.yaml, the expected value for the 'reset-names'
property is "phy".
Change it accordingly to fix the following schema warning:
imx8qm-apalis-ixora-v1.1.dtb: ethernet-phy@7: reset-names:0: 'phy' was expected
from schema $id: http://devicetree.org/schemas/net/ethernet-phy.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per microchip,ksz.yaml, phy-mode is not a valid property in the
top-level switch node.
phy-mode = "rgmii-id" is already passed in the CPU port switch (port@5).
Remove it from the top-level switch node to fix the following
schema warning:
switch@5f: Unevaluated properties are not allowed ('phy-mode' was unexpected)
from schema $id: http://devicetree.org/schemas/net/dsa/microchip,ksz.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the TPM device found on the GW73xx revision F PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the TPM device found on the GW73xx revision F PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per nxp,dwmac-imx.yaml, it is not valid to pass 'phy-supply'.
The reg_module_eth1phy regulator is marked with 'regulator-always-on',
so it is safe to remove it from the eqos node.
Remove it to fix the following schema warning:
imx8mp-verdin-nonwifi-dahlia.dtb: ethernet@30bf0000: Unevaluated properties are not allowed ('phy-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The first compatible entry for the jpegenc should be 'nxp,imx8qm-jpgenc'.
Change it accordingly to fix the following schema warning:
imx8qm-apalis-eval.dtb: jpegenc@58450000: compatible: 'oneOf' conditional failed, one must be fixed:
'nxp,imx8qm-jpgdec' is not one of ['nxp,imx8qxp-jpgdec', 'nxp,imx8qxp-jpgenc']
'nxp,imx8qm-jpgenc' was expected
'nxp,imx8qxp-jpgdec' was expected
Fixes: 5bb279171a ("arm64: dts: imx8: Add jpeg encoder/decoder nodes")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-lpuart.yaml, the dmas and dma-names entries should be
'rx' followed by 'tx'.
Change the order to fix the following schema warning:
imx93-11x11-evk.dtb: serial@44380000: dma-names:0: 'rx' was expected
from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#
imx93-11x11-evk.dtb: serial@44380000: dma-names:1: 'tx' was expected
from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per gateworks-gsc.yaml, #address-cells and #size-cells are mandatory
properties.
Pass them to fix the following schema warning:
imx8mm-venice-gw7903.dtb: gsc@20: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/mfd/gateworks-gsc.yaml#
imx8mm-venice-gw7903.dtb: gsc@20: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/mfd/gateworks-gsc.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass 'fsl,imx8dxl-sc-wdt' to fix the following schema warning:
system-controller: watchdog:compatible:0: 'fsl,imx8qxp-sc-wdt' was expected
from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
system-controller: watchdog:compatible: ['fsl,imx-sc-wdt'] is too short
from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass 'fsl,imx8dxl-sc-thermal' to fix the following schema warning:
system-controller: thermal-sensor:compatible:0: 'fsl,imx8qxp-sc-thermal' was expected
from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
system-controller: thermal-sensor:compatible: ['fsl,imx-sc-thermal'] is too short
from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
wakeup-irq is not documented, and not used anywhere.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass 'fsl,imx8dl-scu-pd' to fix the following schema warning:
system-controller: power-controller:compatible:0: 'fsl,scu-pd' is not one of ['fsl,imx8qm-scu-pd', 'fsl,imx8qxp-scu-pd']
from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Original irq number combined UART irq and DMA irq. These doesn't match
uart driver and dma engine's expection.
Update to the irq numbers, which just uart can trigger.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Wrap the usb controllers in an intermediate simple-bus and use it to
constrain the dma address size of these usb controllers to the 40b
that they generate toward the interconnect. This is required because
the SoC uses 48b address sizes and this mismatch would lead to smmu
context faults [1] because the usb generates 40b addresses while the
smmu page tables are populated with 48b wide addresses.
[1]
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002000010
xhci-hcd xhci-hcd.0.auto: irq 108, io mem 0x03100000
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xffffffb000, fsynr=0x0, cbfrsynra=0xc01, cb=3
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
phyGATE-Tauri uses a phyCORE-i.MX8MM SoM. Add device tree for the board.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- A couple of i.MX8MP device tree changes from Adam Ford to fix clock
configuration regressions caused by 16c9845248 ("arm64: dts: imx8mp:
don't initialize audio clocks from CCM node").
- Fix pmic-irq-hog GPIO line in imx93-tqma9352 device tree.
- Fix a mmemory leak with error handling path of imx_dsp_setup_channels()
in imx-dsp driver.
- Fix HDMI node in imx8mm-evk device tree.
- Add missing clock enable functionality for imx8mm_soc_uid() function
in soc-imx8m driver.
- Add missing imx8mm-prt8mm.dtb build target.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmUSzbIUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6CQgf+JGQJnoZoqywXkg8f8RExTShFuMs3
I01NX+XabEnhGOA88Bx8e8whBUYqZKzPL4UauNBTTIaiJiTRVR3KjSFt5znvrMlW
+sc0MhQUgQYIfM1iBt/pkIiz58n96kkzzj6LHjqpUav15EpudvmxiUCNEQUmBxQM
mj85U1dIn2PqvZP2lGhDMmjAetSftt0BpyeyUUGgjZUS4g4XvQ3wFzyC/wf807uj
COITEEWogt0uCuTLzmbVtpSNR+5TY/naPHHxaepFFSooArsoa51xGJHMk6J/o9i2
d+BEM4CV0OC8XzDSpm0k1Yvxb+ImM23RM50qn3V8ZRQcf0Cwt46R0ikT2Q==
=jN5j
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-6.6' into imx/dt64
i.MX fixes for 6.6:
- A couple of i.MX8MP device tree changes from Adam Ford to fix clock
configuration regressions caused by 16c9845248 ("arm64: dts: imx8mp:
don't initialize audio clocks from CCM node").
- Fix pmic-irq-hog GPIO line in imx93-tqma9352 device tree.
- Fix a mmemory leak with error handling path of imx_dsp_setup_channels()
in imx-dsp driver.
- Fix HDMI node in imx8mm-evk device tree.
- Add missing clock enable functionality for imx8mm_soc_uid() function
in soc-imx8m driver.
- Add missing imx8mm-prt8mm.dtb build target.
The Thermal Monitoring Unit (TMU) interrupt is number 83.
Describe it in the devicetree to fix the following schema warning:
imx93-11x11-evk.dtb: tmu@44482000: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'interrupts-extended' is a required property
from schema $id: http://devicetree.org/schemas/thermal/qoriq-thermal.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per i2c-imx-lpi2c.yaml, the imx8dxl lpi2c compatible should be:
compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c";
Change it accordingly to fix the following schema warning:
imx8dxl-evk.dtb: i2c@5a800000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx8dxl-lpi2c', 'fsl,imx8qxp-lpi2c', 'fsl,imx7ulp-lpi2c'] is too long
'fsl,imx8dxl-lpi2c' is not one of ['fsl,imx7ulp-lpi2c']
'fsl,imx7ulp-lpi2c' was expected
from schema $id: http://devicetree.org/schemas/i2c/i2c-imx-lpi2c.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl,scu-pinctrl.yaml, the pinctrl node names should end with 'grp'.
Change them to fix the following schema warning:
imx8qxp-colibri-iris-v2.dtb: pinctrl: 'enable_3v3_vmmc', 'lcd-lvds' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pinctrl/fsl,scu-pinctrl.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the full compatible list for the imx8dl FEC as per fsl,fec.yaml.
This fixes the following schema warning:
imx8dxl-evk.dtb: ethernet@5b040000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx8qm-fec'] is too short
'fsl,imx8qm-fec' is not one of ['fsl,imx25-fec', 'fsl,imx27-fec', 'fsl,imx28-fec', 'fsl,imx6q-fec', 'fsl,mvf600-fec', 'fsl,s32v234-fec']
'fsl,imx8qm-fec' is not one of ['fsl,imx53-fec', 'fsl,imx6sl-fec']
'fsl,imx8qm-fec' is not one of ['fsl,imx35-fec', 'fsl,imx51-fec']
'fsl,imx8qm-fec' is not one of ['fsl,imx6ul-fec', 'fsl,imx6sx-fec']
'fsl,imx8qm-fec' is not one of ['fsl,imx7d-fec']
'fsl,imx8mq-fec' was expected
'fsl,imx8qm-fec' is not one of ['fsl,imx8mm-fec', 'fsl,imx8mn-fec', 'fsl,imx8mp-fec', 'fsl,imx93-fec']
'fsl,imx8qm-fec' is not one of ['fsl,imx8dxl-fec', 'fsl,imx8qxp-fec']
'fsl,imx8qm-fec' is not one of ['fsl,imx8ulp-fec']
from schema $id: http://devicetree.org/schemas/net/fsl,fec.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'nand-on-flash-bbt' property is a property for the NAND device,
not for the GPMI nand controller.
Remove it to fix the following schema warnings:
imx8mm-ddr4-evk.dtb: nand-controller@33002000: Unevaluated properties are not allowed ('nand-on-flash-bbt' was unexpected)
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
imx8mn-bsh-smm-s2.dtb: nand-controller@33002000: Unevaluated properties are not allowed ('nand-on-flash-bbt' was unexpected)
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mac-address is passed as a subnode of the eeprom and its 'reg'
property describe a range of addresses in the eeprom.
Therefore, #size-cells should be set to 1 instead of 0.
This fixes the following schema warnings:
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: #size-cells:0:0: 1 was expected
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: mac-address@0:reg: [[0], [12]] is too long
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: mac-address@c:reg: [[12], [12]] is too long
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'mac-address@0', 'mac-address@c' were unexpected)
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PWM interrupt is mandatory per imx-pwm.yaml.
Add them.
This also fixes the followig schema warning:
imx8qm-apalis-v1.1-ixora-v1.2.dtb: pwm@5d000000: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'interrupts-extended' is a required property
from schema $id: http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-prt8mm.dts was not getting built. Add it to the build.
Fixes: 58497d7a13 ("arm64: dts: imx: add Protonic PRT8MM board")
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per bq25890.yaml, 'phys', 'ti,use-vinmin-threshold', 'ti,vinmin-threshold'
are not valid properties.
Remove them to fix the following schema warning:
imx8mq-librem5-r2.dtb: charger@6a: Unevaluated properties are not allowed ('phys', 'ti,use-vinmin-threshold', 'ti,vinmin-threshold' were unexpected)
from schema $id: http://devicetree.org/schemas/power/supply/bq25890.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-imx-gpio.yaml, 'pad-wakeup' and 'pad-wakeup-num' are not
valid properties/
Remove them to fix the following schema warning:
imx8qm-apalis-ixora-v1.1.dtb: gpio@5d0a0000: 'pad-wakeup', 'pad-wakeup-num' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-imx-gpio.yaml, 'ngpios' is not a valid property.
Remove it to fix the following schema warning:
imx8qm-apalis-v1.1-ixora-v1.2.dtb: gpio@5d0d0000: 'ngpios' does not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
