all callers of ->aio_read() and ->aio_write() have iov/nr_segs already
checked - generic_segment_checks() done after that is just an odd way
to spell iov_length().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The patch addresses two use-cases when the flag may be safely cleared:
1. fuse_do_setattr() is called with ATTR_CTIME flag set in attr->ia_valid.
In this case attr->ia_ctime bears actual value. In-kernel fuse must send it
to the userspace server and then assign the value to inode->i_ctime.
2. fuse_do_setattr() is called with ATTR_SIZE flag set in attr->ia_valid,
whereas ATTR_CTIME is not set (truncate(2)).
In this case in-kernel fuse must sent "now" to the userspace server and then
assign the value to inode->i_ctime.
In both cases we could clear I_DIRTY_SYNC, but that needs more thought.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Let the kernel maintain i_ctime locally: update i_ctime explicitly on
truncate, fallocate, open(O_TRUNC), setxattr, removexattr, link, rename,
unlink.
The inode flag I_DIRTY_SYNC serves as indication that local i_ctime should
be flushed to the server eventually. The patch sets the flag and updates
i_ctime in course of operations listed above.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch extends fuse_setattr_in, and extends the flush procedure
(fuse_flush_times()) called on ->write_inode() to send the ctime as well as
mtime.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Allow userspace fs to specify time granularity.
This is needed because with writeback_cache mode the kernel is responsible
for generating mtime and ctime, but if the underlying filesystem doesn't
support nanosecond granularity then the cache will contain a different
value from the one stored on the filesystem resulting in a change of times
after a cache flush.
Make the default granularity 1s.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
...and flush mtime from this. This allows us to use the kernel
infrastructure for writing out dirty metadata (mtime at this point, but
ctime in the next patches and also maybe atime).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Don't need to start I/O twice (once without i_mutex and one within).
Also make sure that even if the userspace filesystem doesn't support FSYNC
we do all the steps other than sending the message.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
In case of fc->atomic_o_trunc is set, fuse does nothing in
fuse_do_setattr() while handling open(O_TRUNC). Hence, i_mtime must be
updated explicitly in fuse_finish_open(). The patch also adds extra locking
encompassing open(O_TRUNC) operation to avoid races between the truncation
and updating i_mtime.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Handling truncate(2), VFS doesn't set ATTR_MTIME bit in iattr structure;
only ATTR_SIZE bit is set. In-kernel fuse must handle the case by setting
mtime fields of struct fuse_setattr_in to "now" and set FATTR_MTIME bit
even though ATTR_MTIME was not set.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
When inode is in I_NEW state, inode->i_mode is not initialized yet. Do not
use it before fuse_init_inode() is called.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
filemap_map_pages() is generic implementation of ->map_pages() for
filesystems who uses page cache.
It should be safe to use filemap_map_pages() for ->map_pages() if
filesystem use filemap_fault() for ->fault().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ning Qu <quning@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a staging driver; fix included. Greg KH said he'd take the patch
but hadn't as the merge window opened, so it's included here
to avoid breaking build.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=yzUO
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Nothing major: the stricter permissions checking for sysfs broke a
staging driver; fix included. Greg KH said he'd take the patch but
hadn't as the merge window opened, so it's included here to avoid
breaking build"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
staging: fix up speakup kobject mode
Use 'E' instead of 'X' for unsigned module taint flag.
VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.
kallsyms: fix percpu vars on x86-64 with relocation.
kallsyms: generalize address range checking
module: LLVMLinux: Remove unused function warning from __param_check macro
Fix: module signature vs tracepoints: add new TAINT_UNSIGNED_MODULE
module: remove MODULE_GENERIC_TABLE
module: allow multiple calls to MODULE_DEVICE_TABLE() per module
module: use pr_cont
and COLLAPSE_RANGE fallocate operations, and scalability improvements
in the jbd2 layer and in xattr handling when the extended attributes
spill over into an external block.
Other than that, the usual clean ups and minor bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=4s1Z
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Major changes for 3.14 include support for the newly added ZERO_RANGE
and COLLAPSE_RANGE fallocate operations, and scalability improvements
in the jbd2 layer and in xattr handling when the extended attributes
spill over into an external block.
Other than that, the usual clean ups and minor bug fixes"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (42 commits)
ext4: fix premature freeing of partial clusters split across leaf blocks
ext4: remove unneeded test of ret variable
ext4: fix comment typo
ext4: make ext4_block_zero_page_range static
ext4: atomically set inode->i_flags in ext4_set_inode_flags()
ext4: optimize Hurd tests when reading/writing inodes
ext4: kill i_version support for Hurd-castrated file systems
ext4: each filesystem creates and uses its own mb_cache
fs/mbcache.c: doucple the locking of local from global data
fs/mbcache.c: change block and index hash chain to hlist_bl_node
ext4: Introduce FALLOC_FL_ZERO_RANGE flag for fallocate
ext4: refactor ext4_fallocate code
ext4: Update inode i_size after the preallocation
ext4: fix partial cluster handling for bigalloc file systems
ext4: delete path dealloc code in ext4_ext_handle_uninitialized_extents
ext4: only call sync_filesystm() when remounting read-only
fs: push sync_filesystem() down to the file system's remount_fs()
jbd2: improve error messages for inconsistent journal heads
jbd2: minimize region locked by j_list_lock in jbd2_journal_forget()
jbd2: minimize region locked by j_list_lock in journal_get_create_access()
...
Pull fuse update from Miklos Szeredi:
"This series adds cached writeback support to fuse, improving write
throughput"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix "uninitialized variable" warning
fuse: Turn writeback cache on
fuse: Fix O_DIRECT operations vs cached writeback misorder
fuse: fuse_flush() should wait on writeback
fuse: Implement write_begin/write_end callbacks
fuse: restructure fuse_readpage()
fuse: Flush files on wb close
fuse: Trust kernel i_mtime only
fuse: Trust kernel i_size only
fuse: Connection bit for enabling writeback
fuse: Prepare to handle short reads
fuse: Linking file to inode helper
Reclaim will be leaving shadow entries in the page cache radix tree upon
evicting the real page. As those pages are found from the LRU, an
iput() can lead to the inode being freed concurrently. At this point,
reclaim must no longer install shadow pages because the inode freeing
code needs to ensure the page tree is really empty.
Add an address_space flag, AS_EXITING, that the inode freeing code sets
under the tree lock before doing the final truncate. Reclaim will check
for this flag before installing shadow pages.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Luigi Semenzato <semenzato@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Metin Doslu <metin@citusdata.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Ozgun Erdogan <ozgun@citusdata.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roman Gushchin <klamm@yandex-team.ru>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warning:
In file included from include/linux/fs.h:16:0,
from fs/fuse/fuse_i.h:13,
from fs/fuse/file.c:9:
fs/fuse/file.c: In function 'fuse_file_poll':
include/linux/rbtree.h:82:28: warning: 'parent' may be used
uninitialized in this function [-Wmaybe-uninitialized]
fs/fuse/file.c:2592:27: note: 'parent' was declared here
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Introduce a bit kernel and userspace exchange between each-other on
the init stage and turn writeback on if the userspace want this and
mount option 'allow_wbcache' is present (controlled by fusermount).
Also add each writable file into per-inode write list and call the
generic_file_aio_write to make use of the Linux page cache engine.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The problem is:
1. write cached data to a file
2. read directly from the same file (via another fd)
The 2nd operation may read stale data, i.e. the one that was in a file
before the 1st op. Problem is in how fuse manages writeback.
When direct op occurs the core kernel code calls filemap_write_and_wait
to flush all the cached ops in flight. But fuse acks the writeback right
after the ->writepages callback exits w/o waiting for the real write to
happen. Thus the subsequent direct op proceeds while the real writeback
is still in flight. This is a problem for backends that reorder operation.
Fix this by making the fuse direct IO callback explicitly wait on the
in-flight writeback to finish.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The aim of .flush fop is to hint file-system that flushing its state or caches
or any other important data to reliable storage would be desirable now.
fuse_flush() passes this hint by sending FUSE_FLUSH request to userspace.
However, dirty pages and pages under writeback may be not visible to userspace
yet if we won't ensure it explicitly.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The .write_begin and .write_end are requiered to use generic routines
(generic_file_aio_write --> ... --> generic_perform_write) for buffered
writes.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Move the code filling and sending read request to a separate function. Future
patches will use it for .write_begin -- partial modification of a page
requires reading the page from the storage very similarly to what fuse_readpage
does.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Any write request requires a file handle to report to the userspace. Thus
when we close a file (and free the fuse_file with this info) we have to
flush all the outstanding dirty pages.
filemap_write_and_wait() is enough because every page under fuse writeback
is accounted in ff->count. This delays actual close until all fuse wb is
completed.
In case of "write cache" turned off, the flush is ensured by fuse_vma_close().
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Let the kernel maintain i_mtime locally:
- clear S_NOCMTIME
- implement i_op->update_time()
- flush mtime on fsync and last close
- update i_mtime explicitly on truncate and fallocate
Fuse inode flag FUSE_I_MTIME_DIRTY serves as indication that local i_mtime
should be flushed to the server eventually.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Make fuse think that when writeback is on the inode's i_size is always
up-to-date and not update it with the value received from the userspace.
This is done because the page cache code may update i_size without letting
the FS know.
This assumption implies fixing the previously introduced short-read helper --
when a short read occurs the 'hole' is filled with zeroes.
fuse_file_fallocate() is also fixed because now we should keep i_size up to
date, so it must be updated if FUSE_FALLOCATE request succeeded.
Signed-off-by: Maxim V. Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Off (0) by default. Will be used in the next patches and will be turned
on at the very end.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
A helper which gets called when read reports less bytes than was requested.
See patch "trust kernel i_size only" for details.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
When writeback is ON every writeable file should be in per-inode write list,
not only mmap-ed ones. Thus introduce a helper for this linkage.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Summary of http://lkml.org/lkml/2014/3/14/363 :
Ted: module_param(queue_depth, int, 444)
Joe: 0444!
Rusty: User perms >= group perms >= other perms?
Joe: CLASS_ATTR, DEVICE_ATTR, SENSOR_ATTR and SENSOR_ATTR_2?
Side effect of stricter permissions means removing the unnecessary
S_IFREG from several callers.
Note that the BUILD_BUG_ON_ZERO((perm) & 2) test was removed: a fair
number of drivers fail this test, so that will be the debate for a
future patch.
Suggested-by: Joe Perches <joe@perches.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> for drivers/pci/slot.c
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull vfs updates from Al Viro:
"Assorted stuff; the biggest pile here is Christoph's ACL series. Plus
assorted cleanups and fixes all over the place...
There will be another pile later this week"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (43 commits)
__dentry_path() fixes
vfs: Remove second variable named error in __dentry_path
vfs: Is mounted should be testing mnt_ns for NULL or error.
Fix race when checking i_size on direct i/o read
hfsplus: remove can_set_xattr
nfsd: use get_acl and ->set_acl
fs: remove generic_acl
nfs: use generic posix ACL infrastructure for v3 Posix ACLs
gfs2: use generic posix ACL infrastructure
jfs: use generic posix ACL infrastructure
xfs: use generic posix ACL infrastructure
reiserfs: use generic posix ACL infrastructure
ocfs2: use generic posix ACL infrastructure
jffs2: use generic posix ACL infrastructure
hfsplus: use generic posix ACL infrastructure
f2fs: use generic posix ACL infrastructure
ext2/3/4: use generic posix ACL infrastructure
btrfs: use generic posix ACL infrastructure
fs: make posix_acl_create more useful
fs: make posix_acl_chmod more useful
...
So far I've had one ACK for this, and no other comments. So I think it
is probably time to send this via some suitable tree. I'm guessing that
the vfs tree would be the most appropriate route, but not sure that
there is one at the moment (don't see anything recent at kernel.org)
so in that case I think -mm is the "back up plan". Al, please let me
know if you will take this?
Steve.
---------------------
Following on from the "Re: [PATCH v3] vfs: fix a bug when we do some dio
reads with append dio writes" thread on linux-fsdevel, this patch is my
current version of the fix proposed as option (b) in that thread.
Removing the i_size test from the direct i/o read path at vfs level
means that filesystems now have to deal with requests which are beyond
i_size themselves. These I've divided into three sets:
a) Those with "no op" ->direct_IO (9p, cifs, ceph)
These are obviously not going to be an issue
b) Those with "home brew" ->direct_IO (nfs, fuse)
I've been told that NFS should not have any problem with the larger
i_size, however I've added an extra test to FUSE to duplicate the
original behaviour just to be on the safe side.
c) Those using __blockdev_direct_IO()
These call through to ->get_block() which should deal with the EOF
condition correctly. I've verified that with GFS2 and I believe that
Zheng has verified it for ext4. I've also run the test on XFS and it
passes both before and after this change.
The part of the patch in filemap.c looks a lot larger than it really is
- there are only two lines of real change. The rest is just indentation
of the contained code.
There remains a test of i_size though, which was added for btrfs. It
doesn't cause the other filesystems a problem as the test is performed
after ->direct_IO has been called. It is possible that there is a race
that does matter to btrfs, however this patch doesn't change that, so
its still an overall improvement.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reported-by: Zheng Liu <gnehzuil.liu@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
open/release operations require userspace transitions to keep track
of the open count and to perform any FS-specific setup. However,
for some purely read-only FSs which don't need to perform any setup
at open/release time, we can avoid the performance overhead of
calling into userspace for open/release calls.
This patch adds the necessary support to the fuse kernel modules to prevent
open/release operations from hitting in userspace. When the client returns
ENOSYS, we avoid sending the subsequent release to userspace, and also
remember this so that future opens also don't trigger a userspace
operation.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Various read operations (e.g. readlink, readdir) invalidate the cached
attrs for atime changes. This patch adds a new function
'fuse_invalidate_atime', which checks for a read-only super block and
avoids the attr invalidation in that case.
Signed-off-by: Andrew Gallagher <andrewjcg@fb.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
As noticed by Coverity the "num != 0" condition never triggers. Instead it
should check for a complete page.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Having this struct in module memory could Oops when if the module is
unloaded while the buffer still persists in a pipe.
Since sock_pipe_buf_ops is essentially the same as fuse_dev_pipe_buf_steal
merge them into nosteal_pipe_buf_ops (this is the same as
default_pipe_buf_ops except stealing the page from the buffer is not
allowed).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
All async fuse requests must be supplied with extra reference to a fuse
file. This is necessary to ensure that the fuse file is not released until
all in-flight requests are completed. Fuse secondary writeback requests
must obey this rule as well.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
BDI_WRITTEN counter is used to estimate bdi bandwidth. It must be
incremented every time as bdi ends page writeback. No matter whether it
was fulfilled by actual write or by discarding the request (e.g. due to
shrunk i_size).
Note that even before writepages patches, the case "Got truncated off
completely" was handled in fuse_send_writepage() by calling
fuse_writepage_finish() which updated BDI_WRITTEN unconditionally.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
If writeback happens while fuse is in FUSE_NOWRITE condition, the request
will be queued but not processed immediately (see fuse_flush_writepages()).
Until FUSE_NOWRITE becomes relaxed, more writebacks can happen. They will
be queued as "secondary" requests to that first ("primary") request.
Existing implementation crops only primary request. This is not correct
because a subsequent extending write(2) may increase i_size and then
secondary requests won't be cropped properly. The result would be stale
data written to the server to a file offset where zeros must be.
Similar problem may happen if secondary requests are attached to an
in-flight request that was already cropped.
The patch solves the issue by cropping all secondary requests in
fuse_writepage_end(). Thanks to Miklos for idea.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
fuse_writepage_in_flight() returns false if it fails to find request with
given index in fi->writepages. Then the caller proceeds with populating
data->orig_pages[] and incrementing req->num_pages. Hence,
fuse_writepage_in_flight() must revert changes it made in request before
returning false.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
...which just returns -EBUSY if a directory alias would be created.
This is to be used by fuse mkdir to make sure that a buggy or malicious
userspace filesystem doesn't do anything nasty. Previously fuse used a
private mutex for this purpose, which can now go away.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
This allows udev (or more recently systemd-tmpfiles) to create /dev/cuse on
boot, in the same way as /dev/fuse is currently created, and the corresponding
module to be loaded on first access.
The corresponding functionalty was introduced for fuse in commit 578454f.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
If ->writepage() tries to write back a page whose copy is still in flight,
then just skip by calling redirty_page_for_writepage().
This is OK, since now ->writepage() should never be called for data
integrity sync.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
As Maxim Patlasov pointed out, it's possible to get a dirty page while it's
copy is still under writeback, despite fuse_page_mkwrite() doing its thing
(direct IO).
This could result in two concurrent write request for the same offset, with
data corruption if they get mixed up.
To prevent this, fuse needs to check and delay such writes. This
implementation does this by:
1. check if page is still under writeout, if so create a new, single page
secondary request for it
2. chain this secondary request onto the in-flight request
2/a. if a seconday request for the same offset was already chained to the
in-flight request, then just copy the contents of the page and discard
the new secondary request. This makes sure that for each page will
have at most two requests associated with it
3. when the in-flight request finished, send off all secondary requests
chained onto it
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Checking against tmp-page indexes is not very useful, and results in one
(or rarely two) page requests. Which is not much of an improvement...
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch fixes a race between ftruncate(2), mmap-ed write and write(2):
1) An user makes a page dirty via mmap-ed write.
2) The user performs shrinking truncate(2) intended to purge the page.
3) Before fuse_do_setattr calls truncate_pagecache, the page goes to
writeback. fuse_writepages_fill attaches a new page to FUSE_WRITE request,
then releases the original page by end_page_writeback and unlock it.
4) fuse_do_setattr completes and successfully returns. Since now, i_mutex
is free.
5) Ordinary write(2) extends i_size back to cover the page. Note that
fuse_send_write_pages do wait for fuse writeback, but for another
page->index.
6) fuse_writepages_fill attaches more pages to the request (if any), then
fuse_writepages_send is eventually called. It is supposed to crop
inarg->size of the request, but it doesn't because i_size has already been
extended back.
Moving end_page_writeback behind fuse_writepages_send guarantees that
__fuse_release_nowrite (called from fuse_do_setattr) will crop inarg->size
of the request before write(2) gets the chance to extend i_size.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The .writepages one is required to make each writeback request carry more than
one page on it. The patch enables optimized behaviour unconditionally,
i.e. mmap-ed writes will benefit from the patch even if fc->writeback_cache=0.
[SzM: simplify, add comments]
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Don't bug if there's no writable files found for page writeback. If ever
this is triggered, a WARN_ON helps debugging it much better then a BUG_ON.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Lock the page in fuse_page_mkwrite() to protect against a race with
fuse_writepage() where the page is redirtied before the actual writeback
begins.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The .writepages callback will issue writeback requests with more than one
page aboard. Make existing end/check code be aware of this.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
There will be a .writepageS callback implementation which will need to
get a fuse_file out of a fuse_inode, thus make a helper for this.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Doing dput(parent) is not valid in RCU walk mode. In RCU mode it would
probably be okay to update the parent flags, but it's actually not
necessary most of the time...
So only set the FUSE_I_ADVISE_RDPLUS flag on the parent when the entry was
recently initialized by READDIRPLUS.
This is achieved by setting FUSE_I_INIT_RDPLUS on entries added by
READDIRPLUS and only dropping out of RCU mode if this flag is set.
FUSE_I_INIT_RDPLUS is cleared once the FUSE_I_ADVISE_RDPLUS flag is set in
the parent.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
If revalidate finds an invalid dentry in RCU walk mode, let the VFS deal
with it instead of calling check_submounts_and_drop() which is not prepared
for being called from RCU walk.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
A former patch introducing FUSE_I_SIZE_UNSTABLE flag provided detailed
description of races between ftruncate and anyone who can extend i_size:
> 1. As in the previous scenario fuse_dentry_revalidate() discovered that i_size
> changed (due to our own fuse_do_setattr()) and is going to call
> truncate_pagecache() for some 'new_size' it believes valid right now. But by
> the time that particular truncate_pagecache() is called ...
> 2. fuse_do_setattr() returns (either having called truncate_pagecache() or
> not -- it doesn't matter).
> 3. The file is extended either by write(2) or ftruncate(2) or fallocate(2).
> 4. mmap-ed write makes a page in the extended region dirty.
This patch adds necessary bits to fuse_file_fallocate() to protect from that
race.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
The patch fixes a race between mmap-ed write and fallocate(PUNCH_HOLE):
1) An user makes a page dirty via mmap-ed write.
2) The user performs fallocate(2) with mode == PUNCH_HOLE|KEEP_SIZE
and <offset, size> covering the page.
3) Before truncate_pagecache_range call from fuse_file_fallocate,
the page goes to write-back. The page is fully processed by fuse_writepage
(including end_page_writeback on the page), but fuse_flush_writepages did
nothing because fi->writectr < 0.
4) truncate_pagecache_range is called and fuse_file_fallocate is finishing
by calling fuse_release_nowrite. The latter triggers processing queued
write-back request which will write stale data to the hole soon.
Changed in v2 (thanks to Brian for suggestion):
- Do not truncate page cache until FUSE_FALLOCATE succeeded. Otherwise,
we can end up in returning -ENOTSUPP while user data is already punched
from page cache. Use filemap_write_and_wait_range() instead.
Changed in v3 (thanks to Miklos for suggestion):
- fuse_wait_on_writeback() is prone to livelocks; use fuse_set_nowrite()
instead. So far as we need a dirty-page barrier only, fuse_sync_writes()
should be enough.
- rebased to for-linus branch of fuse.git
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
truncate_pagecache() doesn't care about old size since commit
cedabed49b ("vfs: Fix vmtruncate() regression"). Let's drop it.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The feature prevents mistrusted filesystems (ie: FUSE mounts created by
unprivileged users) to grow a large number of dirty pages before
throttling. For such filesystems balance_dirty_pages always check bdi
counters against bdi limits. I.e. even if global "nr_dirty" is under
"freerun", it's not allowed to skip bdi checks. The only use case for now
is fuse: it sets bdi max_ratio to 1% by default and system administrators
are supposed to expect that this limit won't be exceeded.
The feature is on if a BDI is marked by BDI_CAP_STRICTLIMIT flag. A
filesystem may set the flag when it initializes its BDI.
The problematic scenario comes from the fact that nobody pays attention to
the NR_WRITEBACK_TEMP counter (i.e. number of pages under fuse
writeback). The implementation of fuse writeback releases original page
(by calling end_page_writeback) almost immediately. A fuse request queued
for real processing bears a copy of original page. Hence, if userspace
fuse daemon doesn't finalize write requests in timely manner, an
aggressive mmap writer can pollute virtually all memory by those temporary
fuse page copies. They are carefully accounted in NR_WRITEBACK_TEMP, but
nobody cares.
To make further explanations shorter, let me use "NR_WRITEBACK_TEMP
problem" as a shortcut for "a possibility of uncontrolled grow of amount
of RAM consumed by temporary pages allocated by kernel fuse to process
writeback".
The problem was very easy to reproduce. There is a trivial example
filesystem implementation in fuse userspace distribution: fusexmp_fh.c. I
added "sleep(1);" to the write methods, then recompiled and mounted it.
Then created a huge file on the mount point and run a simple program which
mmap-ed the file to a memory region, then wrote a data to the region. An
hour later I observed almost all RAM consumed by fuse writeback. Since
then some unrelated changes in kernel fuse made it more difficult to
reproduce, but it is still possible now.
Putting this theoretical happens-in-the-lab thing aside, there is another
thing that really hurts real world (FUSE) users. This is write-through
page cache policy FUSE currently uses. I.e. handling write(2), kernel
fuse populates page cache and flushes user data to the server
synchronously. This is excessively suboptimal. Pavel Emelyanov's patches
("writeback cache policy") solve the problem, but they also make resolving
NR_WRITEBACK_TEMP problem absolutely necessary. Otherwise, simply copying
a huge file to a fuse mount would result in memory starvation. Miklos,
the maintainer of FUSE, believes strictlimit feature the way to go.
And eventually putting FUSE topics aside, there is one more use-case for
strictlimit feature. Using a slow USB stick (mass storage) in a machine
with huge amount of RAM installed is a well-known pain. Let's make simple
computations. Assuming 64GB of RAM installed, existing implementation of
balance_dirty_pages will start throttling only after 9.6GB of RAM becomes
dirty (freerun == 15% of total RAM). So, the command "cp 9GB_file
/media/my-usb-storage/" may return in a few seconds, but subsequent
"umount /media/my-usb-storage/" will take more than two hours if effective
throughput of the storage is, to say, 1MB/sec.
After inclusion of strictlimit feature, it will be trivial to add a knob
(e.g. /sys/devices/virtual/bdi/x:y/strictlimit) to enable it on demand.
Manually or via udev rule. May be I'm wrong, but it seems to be quite a
natural desire to limit the amount of dirty memory for some devices we are
not fully trust (in the sense of sustainable throughput).
[akpm@linux-foundation.org: fix warning in page-writeback.c]
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull fuse bugfixes from Miklos Szeredi:
"Just a bunch of bugfixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use list_for_each_entry() for list traversing
fuse: readdir: check for slash in names
fuse: hotfix truncate_pagecache() issue
fuse: invalidate inode attributes on xattr modification
fuse: postpone end_page_writeback() in fuse_writepage_locked()
Drop a subtree when we find that it has moved or been delated. This can be
done as long as there are no submounts under this location.
If the directory was moved and we come across the same directory in a
future lookup it will be reconnected by d_materialise_unique().
Signed-off-by: Anand Avati <avati@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
On errors unrelated to the filesystem's state (ENOMEM, ENOTCONN) return the
error itself from ->d_revalidate() insted of returning zero (invalid).
Also make a common label for invalidating the dentry. This will be used by
the next patch.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use d_materialise_unique() instead of d_splice_alias(). This allows dentry
subtrees to be moved to a new place if there moved, even if something is
referencing a dentry in the subtree (open fd, cwd, etc..).
This will also allow us to drop a subtree if it is found to be replaced by
something else. In this case the disconnected subtree can later be
reconnected to its new location.
d_materialise_unique() ensures that a directory entry only ever has one
alias. We keep fc->inst_mutex around the calls for d_materialise_unique()
on directories to prevent a race with mkdir "stealing" the inode.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Userspace can add names containing a slash character to the directory
listing. Don't allow this as it could cause all sorts of trouble.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
The way how fuse calls truncate_pagecache() from fuse_change_attributes()
is completely wrong. Because, w/o i_mutex held, we never sure whether
'oldsize' and 'attr->size' are valid by the time of execution of
truncate_pagecache(inode, oldsize, attr->size). In fact, as soon as we
released fc->lock in the middle of fuse_change_attributes(), we completely
loose control of actions which may happen with given inode until we reach
truncate_pagecache. The list of potentially dangerous actions includes
mmap-ed reads and writes, ftruncate(2) and write(2) extending file size.
The typical outcome of doing truncate_pagecache() with outdated arguments
is data corruption from user point of view. This is (in some sense)
acceptable in cases when the issue is triggered by a change of the file on
the server (i.e. externally wrt fuse operation), but it is absolutely
intolerable in scenarios when a single fuse client modifies a file without
any external intervention. A real life case I discovered by fsx-linux
looked like this:
1. Shrinking ftruncate(2) comes to fuse_do_setattr(). The latter sends
FUSE_SETATTR to the server synchronously, but before getting fc->lock ...
2. fuse_dentry_revalidate() is asynchronously called. It sends FUSE_LOOKUP
to the server synchronously, then calls fuse_change_attributes(). The
latter updates i_size, releases fc->lock, but before comparing oldsize vs
attr->size..
3. fuse_do_setattr() from the first step proceeds by acquiring fc->lock and
updating attributes and i_size, but now oldsize is equal to
outarg.attr.size because i_size has just been updated (step 2). Hence,
fuse_do_setattr() returns w/o calling truncate_pagecache().
4. As soon as ftruncate(2) completes, the user extends file size by
write(2) making a hole in the middle of file, then reads data from the hole
either by read(2) or mmap-ed read. The user expects to get zero data from
the hole, but gets stale data because truncate_pagecache() is not executed
yet.
The scenario above illustrates one side of the problem: not truncating the
page cache even though we should. Another side corresponds to truncating
page cache too late, when the state of inode changed significantly.
Theoretically, the following is possible:
1. As in the previous scenario fuse_dentry_revalidate() discovered that
i_size changed (due to our own fuse_do_setattr()) and is going to call
truncate_pagecache() for some 'new_size' it believes valid right now. But
by the time that particular truncate_pagecache() is called ...
2. fuse_do_setattr() returns (either having called truncate_pagecache() or
not -- it doesn't matter).
3. The file is extended either by write(2) or ftruncate(2) or fallocate(2).
4. mmap-ed write makes a page in the extended region dirty.
The result will be the lost of data user wrote on the fourth step.
The patch is a hotfix resolving the issue in a simplistic way: let's skip
dangerous i_size update and truncate_pagecache if an operation changing
file size is in progress. This simplistic approach looks correct for the
cases w/o external changes. And to handle them properly, more sophisticated
and intrusive techniques (e.g. NFS-like one) would be required. I'd like to
postpone it until the issue is well discussed on the mailing list(s).
Changed in v2:
- improved patch description to cover both sides of the issue.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Calls like setxattr and removexattr result in updation of ctime.
Therefore invalidate inode attributes to force a refresh.
Signed-off-by: Anand Avati <avati@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
The patch fixes a race between ftruncate(2), mmap-ed write and write(2):
1) An user makes a page dirty via mmap-ed write.
2) The user performs shrinking truncate(2) intended to purge the page.
3) Before fuse_do_setattr calls truncate_pagecache, the page goes to
writeback. fuse_writepage_locked fills FUSE_WRITE request and releases
the original page by end_page_writeback.
4) fuse_do_setattr() completes and successfully returns. Since now, i_mutex
is free.
5) Ordinary write(2) extends i_size back to cover the page. Note that
fuse_send_write_pages do wait for fuse writeback, but for another
page->index.
6) fuse_writepage_locked proceeds by queueing FUSE_WRITE request.
fuse_send_writepage is supposed to crop inarg->size of the request,
but it doesn't because i_size has already been extended back.
Moving end_page_writeback to the end of fuse_writepage_locked fixes the
race because now the fact that truncate_pagecache is successfully returned
infers that fuse_writepage_locked has already called end_page_writeback.
And this, in turn, infers that fuse_flush_writepages has already called
fuse_send_writepage, and the latter used valid (shrunk) i_size. write(2)
could not extend it because of i_mutex held by ftruncate(2).
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the cuse class code to use the
correct field.
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuse does instantiation slightly differently from NFS/CIFS which use
d_materialise_unique().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org
Add sanity checks before adding or updating an entry with data received
from readdirplus.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org
In case d_lookup() returns a dentry with d_inode == NULL, the dentry is not
returned with dput(). This results in triggering a BUG() in
shrink_dcache_for_umount_subtree():
BUG: Dentry ...{i=0,n=...} still in use (1) [unmount of fuse fuse]
[SzM: need to d_drop() as well]
Reported-by: Justin Clift <jclift@redhat.com>
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Brian Foster <bfoster@redhat.com>
Tested-by: Niels de Vos <ndevos@redhat.com>
CC: stable@vger.kernel.org
The global variable num_physpages is scheduled to be removed, so use
totalram_pages instead of num_physpages at runtime.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull second set of VFS changes from Al Viro:
"Assorted f_pos race fixes, making do_splice_direct() safe to call with
i_mutex on parent, O_TMPFILE support, Jeff's locks.c series,
->d_hash/->d_compare calling conventions changes from Linus, misc
stuff all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
Document ->tmpfile()
ext4: ->tmpfile() support
vfs: export lseek_execute() to modules
lseek_execute() doesn't need an inode passed to it
block_dev: switch to fixed_size_llseek()
cpqphp_sysfs: switch to fixed_size_llseek()
tile-srom: switch to fixed_size_llseek()
proc_powerpc: switch to fixed_size_llseek()
ubi/cdev: switch to fixed_size_llseek()
pci/proc: switch to fixed_size_llseek()
isapnp: switch to fixed_size_llseek()
lpfc: switch to fixed_size_llseek()
locks: give the blocked_hash its own spinlock
locks: add a new "lm_owner_key" lock operation
locks: turn the blocked_list into a hashtable
locks: convert fl_link to a hlist_node
locks: avoid taking global lock if possible when waking up blocked waiters
locks: protect most of the file_lock handling with i_lock
locks: encapsulate the fl_link list handling
locks: make "added" in __posix_lock_file a bool
...
Pull VFS patches (part 1) from Al Viro:
"The major change in this pile is ->readdir() replacement with
->iterate(), dealing with ->f_pos races in ->readdir() instances for
good.
There's a lot more, but I'd prefer to split the pull request into
several stages and this is the first obvious cutoff point."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (67 commits)
[readdir] constify ->actor
[readdir] ->readdir() is gone
[readdir] convert ecryptfs
[readdir] convert coda
[readdir] convert ocfs2
[readdir] convert fatfs
[readdir] convert xfs
[readdir] convert btrfs
[readdir] convert hostfs
[readdir] convert afs
[readdir] convert ncpfs
[readdir] convert hfsplus
[readdir] convert hfs
[readdir] convert befs
[readdir] convert cifs
[readdir] convert freevxfs
[readdir] convert fuse
[readdir] convert hpfs
reiserfs: switch reiserfs_readdir_dentry to inode
reiserfs: is_privroot_deh() needs only directory inode, actually
...
Changing size of a file on server and local update (fuse_write_update_size)
should be always protected by inode->i_mutex. Otherwise a race like this is
possible:
1. Process 'A' calls fallocate(2) to extend file (~FALLOC_FL_KEEP_SIZE).
fuse_file_fallocate() sends FUSE_FALLOCATE request to the server.
2. Process 'B' calls ftruncate(2) shrinking the file. fuse_do_setattr()
sends shrinking FUSE_SETATTR request to the server and updates local i_size
by i_size_write(inode, outarg.attr.size).
3. Process 'A' resumes execution of fuse_file_fallocate() and calls
fuse_write_update_size(inode, offset + length). But 'offset + length' was
obsoleted by ftruncate from previous step.
Changed in v2 (thanks Brian and Anand for suggestions):
- made relation between mutex_lock() and fuse_set_nowrite(inode) more
explicit and clear.
- updated patch description to use ftruncate(2) in example
Signed-off-by: Maxim V. Patlasov <MPatlasov@parallels.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The bug was introduced with async_dio feature: trying to optimize short reads,
we cut number-of-bytes-to-read to i_size boundary. Hence the following example:
truncate --size=300 /mnt/file
dd if=/mnt/file of=/dev/null iflag=direct
led to FUSE_READ request of 300 bytes size. This turned out to be problem
for userspace fuse implementations who rely on assumption that kernel fuse
does not change alignment of request from client FS.
The patch turns off the optimization if async_dio is disabled. And, if it's
enabled, the patch fixes adjustment of number-of-bytes-to-read to preserve
alignment.
Note, that we cannot throw out short read optimization entirely because
otherwise a direct read of a huge size issued on a tiny file would generate
a huge amount of fuse requests and most of them would be ACKed by userspace
with zero bytes read.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
If request submission fails for an async request (i.e.,
get_user_pages() returns -ERESTARTSYS), we currently skip the
-EIOCBQUEUED return and drop into wait_for_sync_kiocb() forever.
Avoid this by always returning -EIOCBQUEUED for async requests. If
an error occurs, the error is passed into fuse_aio_complete(),
returned via aio_complete() and thus propagated to userspace via
io_getevents().
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix bug introduced by commit 4582a4ab2a "FUSE: Adapt readdirplus to application
usage patterns".
We need to check for a positive dentry; negative dentries are not added by
readdirplus. Secondly we need to advise the use of readdirplus on the *parent*,
otherwise the whole thing is useless. Thirdly all this is only relevant if
"readdirplus_auto" mode is selected by the filesystem.
We advise the use of readdirplus only if the dentry was still valid. If we had
to redo the lookup then there was no use in doing the -plus version.
Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Feng Shuo <steve.shuo.feng@gmail.com>
CC: stable@vger.kernel.org
An fallocate request without FALLOC_FL_KEEP_SIZE set can extend the
size of a file. Update the inode size after a successful fallocate.
Also invalidate the inode attributes after a successful fallocate
to ensure we pick up the latest attribute values (i.e., i_blocks).
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
fuse supports hole punch via the fallocate() FALLOC_FL_PUNCH_HOLE
interface. When a hole punch is passed through, the page cache
is not cleared and thus allows reading stale data from the cache.
This is easily demonstrable (using FOPEN_KEEP_CACHE) by reading a
smallish random data file into cache, punching a hole and creating
a copy of the file. Drop caches or remount and observe that the
original file no longer matches the file copied after the hole
punch. The original file contains a zeroed range and the latter
file contains stale data.
Protect against writepage requests in progress and punch out the
associated page cache range after a successful client fs hole
punch.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Commit 8b41e671 introduced explicit background checking for fuse_req
structures with BUG_ON() checks for the appropriate type of request in
in the associated send functions. Commit bcba24cc introduced the ability
to send dio requests as background requests but does not update the
request allocation based on the type of I/O request. As a result, a
BUG_ON() triggers in the fuse_request_send_background() background path if
an async I/O is sent.
Allocate a request based on the async state of the fuse_io_priv to avoid
the BUG.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Merge more incoming from Andrew Morton:
- Various fixes which were stalled or which I picked up recently
- A large rotorooting of the AIO code. Allegedly to improve
performance but I don't really have good performance numbers (I might
have lost the email) and I can't raise Kent today. I held this out
of 3.9 and we could give it another cycle if it's all too late/scary.
I ended up taking only the first two thirds of the AIO rotorooting. I
left the percpu parts and the batch completion for later. - Linus
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (33 commits)
aio: don't include aio.h in sched.h
aio: kill ki_retry
aio: kill ki_key
aio: give shared kioctx fields their own cachelines
aio: kill struct aio_ring_info
aio: kill batch allocation
aio: change reqs_active to include unreaped completions
aio: use cancellation list lazily
aio: use flush_dcache_page()
aio: make aio_read_evt() more efficient, convert to hrtimers
wait: add wait_event_hrtimeout()
aio: refcounting cleanup
aio: make aio_put_req() lockless
aio: do fget() after aio_get_req()
aio: dprintk() -> pr_debug()
aio: move private stuff out of aio.h
aio: add kiocb_cancel()
aio: kill return value of aio_complete()
char: add aio_{read,write} to /dev/{null,zero}
aio: remove retry-based AIO
...
Pull fuse updates from Miklos Szeredi:
"This contains two patchsets from Maxim Patlasov.
The first reworks the request throttling so that only async requests
are throttled. Wakeup of waiting async requests is also optimized.
The second series adds support for async processing of direct IO which
optimizes direct IO and enables the use of the AIO userspace
interface."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: add flag to turn on async direct IO
fuse: truncate file if async dio failed
fuse: optimize short direct reads
fuse: enable asynchronous processing direct IO
fuse: make fuse_direct_io() aware about AIO
fuse: add support of async IO
fuse: move fuse_release_user_pages() up
fuse: optimize wake_up
fuse: implement exclusive wakeup for blocked_waitq
fuse: skip blocking on allocations of synchronous requests
fuse: add flag fc->initialized
fuse: make request allocations for background processing explicit
Without async DIO write requests to a single file were always serialized.
With async DIO that's no longer the case.
So don't turn on async DIO by default for fear of breaking backward
compatibility.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch improves error handling in fuse_direct_IO(): if we successfully
submitted several fuse requests on behalf of synchronous direct write
extending file and some of them failed, let's try to do our best to clean-up.
Changed in v2: reuse fuse_do_setattr(). Thanks to Brian for suggestion.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
If user requested direct read beyond EOF, we can skip sending fuse requests
for positions beyond EOF because userspace would ACK them with zero bytes read
anyway. We can trust to i_size in fuse_direct_IO for such cases because it's
called from fuse_file_aio_read() and the latter updates fuse attributes
including i_size.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
In case of synchronous DIO request (i.e. read(2) or write(2) for a file
opened with O_DIRECT), the patch submits fuse requests asynchronously, but
waits for their completions before return from fuse_direct_IO().
In case of asynchronous DIO request (i.e. libaio io_submit() or a file opened
with O_DIRECT), the patch submits fuse requests asynchronously and return
-EIOCBQUEUED immediately.
The only special case is async DIO extending file. Here the patch falls back
to old behaviour because we can't return -EIOCBQUEUED and update i_size later,
without i_mutex hold. And we have no method to wait on real async I/O
requests.
The patch also clean __fuse_direct_write() up: it's better to update i_size
in its callers. Thanks Brian for suggestion.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch implements passing "struct fuse_io_priv *io" down the stack up to
fuse_send_read/write where it is used to submit request asynchronously.
io->async==0 designates synchronous processing.
Non-trivial part of the patch is changes in fuse_direct_io(): resources
like fuse requests and user pages cannot be released immediately in async
case.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch implements a framework to process an IO request asynchronously. The
idea is to associate several fuse requests with a single kiocb by means of
fuse_io_priv structure. The structure plays the same role for FUSE as 'struct
dio' for direct-io.c.
The framework is supposed to be used like this:
- someone (who wants to process an IO asynchronously) allocates fuse_io_priv
and initializes it setting 'async' field to non-zero value.
- as soon as fuse request is filled, it can be submitted (in non-blocking way)
by fuse_async_req_send()
- when all submitted requests are ACKed by userspace, io->reqs drops to zero
triggering aio_complete()
In case of IO initiated by libaio, aio_complete() will finish processing the
same way as in case of dio_complete() calling aio_complete(). But the
framework may be also used for internal FUSE use when initial IO request
was synchronous (from user perspective), but it's beneficial to process it
asynchronously. Then the caller should wait on kiocb explicitly and
aio_complete() will wake the caller up.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
fuse_release_user_pages() will be indirectly used by fuse_send_read/write
in future patches.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch solves thundering herd problem. So far as previous patches ensured
that only allocations for background may block, it's safe to wake up one
waiter. Whoever it is, it will wake up another one in request_end() afterwards.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
A task may have at most one synchronous request allocated. So these
requests need not be otherwise limited.
The patch re-works fuse_get_req() to follow this idea.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Existing flag fc->blocked is used to suspend request allocation both in case
of many background request submitted and period of time before init_reply
arrives from userspace. Next patch will skip blocking allocations of
synchronous request (disregarding fc->blocked). This is mostly OK, but
we still need to suspend allocations if init_reply is not arrived yet. The
patch introduces flag fc->initialized which will serve this purpose.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
There are two types of processing requests in FUSE: synchronous (via
fuse_request_send()) and asynchronous (via adding to fc->bg_queue).
Fortunately, the type of processing is always known in advance, at the time
of request allocation. This preparatory patch utilizes this fact making
fuse_get_req() aware about the type. Next patches will use it.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
it's used only as a flag to distinguish normal pipes/FIFOs from the
internal per-task one used by file-to-file splice. And pipe->files
would work just as well for that purpose...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Modify the request_module to prefix the file system type with "fs-"
and add aliases to all of the filesystems that can be built as modules
to match.
A common practice is to build all of the kernel code and leave code
that is not commonly needed as modules, with the result that many
users are exposed to any bug anywhere in the kernel.
Looking for filesystems with a fs- prefix limits the pool of possible
modules that can be loaded by mount to just filesystems trivially
making things safer with no real cost.
Using aliases means user space can control the policy of which
filesystem modules are auto-loaded by editing /etc/modprobe.d/*.conf
with blacklist and alias directives. Allowing simple, safe,
well understood work-arounds to known problematic software.
This also addresses a rare but unfortunate problem where the filesystem
name is not the same as it's module name and module auto-loading
would not work. While writing this patch I saw a handful of such
cases. The most significant being autofs that lives in the module
autofs4.
This is relevant to user namespaces because we can reach the request
module in get_fs_type() without having any special permissions, and
people get uncomfortable when a user specified string (in this case
the filesystem type) goes all of the way to request_module.
After having looked at this issue I don't think there is any
particular reason to perform any filtering or permission checks beyond
making it clear in the module request that we want a filesystem
module. The common pattern in the kernel is to call request_module()
without regards to the users permissions. In general all a filesystem
module does once loaded is call register_filesystem() and go to sleep.
Which means there is not much attack surface exposed by loading a
filesytem module unless the filesystem is mounted. In a user
namespace filesystems are not mounted unless .fs_flags = FS_USERNS_MOUNT,
which most filesystems do not set today.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
This patch is a follow up on below patch:
[PATCH] exportfs: add FILEID_INVALID to indicate invalid fid_type
commit: 216b6cbdcb
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Vivek Trivedi <t.vivek@samsung.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Sage Weil <sage@inktank.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For some filesystems (e.g. GlusterFS), the cost of performing a
normal readdir and readdirplus are identical. Since adaptively
using readdirplus has no benefit for those systems, give
users/filesystems the option to control adaptive readdirplus use.
v2 of this patch incorporates Miklos's suggestion to simplify the code,
as well as improving consistency of macro names and documentation.
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
commit 626cf23660 "poll: add poll_requested_events()..." enabled us to send the
requested events to the filesystem.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
drop_nlink() warns if nlink is already zero. This is triggerable by a buggy
userspace filesystem. The cure, I think, is worse than the disease so disable
the warning.
Reported-by: Tero Roponen <tero.roponen@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The all pointers within fuse_req must point to valid memory once
fuse_force_forget() returns.
This bug appeared in "fuse: implement NFS-like readdirplus support"
and was never in any official Linux release.
I tested the fuse_force_forget() code path by injecting to fake -ENOMEM and
verified the FORGET operation was called properly in userspace.
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Use the same adaptive readdirplus mechanism as NFS:
http://permalink.gmane.org/gmane.linux.nfs/49299
If the user space implementation wants to disable readdirplus
temporarily, it could just return ENOTSUPP. Then kernel will
recall it with readdir.
Signed-off-by: Feng Shuo <steve.shuo.feng@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Commit c69e8d9c0 added rcu lock to fuse/dir.c It was assuming
that 'task' is some other process but in fact this parameter always
equals to 'current'. Inline this parameter to make it more readable
and remove RCU lock as it is not needed when access current process
credentials.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
__fuse_direct_io() allocates fuse-requests by calling fuse_get_req(fc, n). The
patch calculates 'n' based on iov[] array. This is useful because allocating
FUSE_MAX_PAGES_PER_REQ page pointers and descriptors for each fuse request
would be waste of memory in case of iov-s of smaller size.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Let fuse_get_user_pages() pack as many iov-s to a single fuse_req as
possible. This is very beneficial in case of iov[] consisting of many
iov-s of relatively small sizes (e.g. PAGE_SIZE).
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch makes preliminary work for the next patch optimizing scatter-gather
direct IO. The idea is to allow fuse_get_user_pages() to pack as many iov-s
to each fuse request as possible. So, here we only rework all related
call-paths to carry iov[] from fuse_direct_IO() to fuse_get_user_pages().
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Previously, anyone who set flag 'argpages' only filled req->pages[] and set
per-request page_offset. This patch re-works all cases where argpages=1 to
fill req->page_descs[] properly.
Having req->page_descs[] filled properly allows to re-work fuse_copy_pages()
to copy page fragments described by req->page_descs[]. This will be useful
for next patches optimizing direct_IO.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The ability to save page pointers along with lengths and offsets in fuse_req
will be useful to cover several iovec-s with a single fuse_req.
Per-request page_offset is removed because anybody who need it can use
req->page_descs[0].offset instead.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
fuse_do_ioctl() already calculates the number of pages it's going to use. It is
stored in 'num_pages' variable. So the patch simply uses it for allocating
fuse_req.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch allocates as many page pointers in fuse_req as needed to cover
interval [pos .. pos+len-1]. Inline helper fuse_wr_pages() is introduced
to hide this cumbersome arithmetic.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch uses 'nr_pages' argument of fuse_readpages() as heuristics for the
number of page pointers to allocate.
This can be improved further by taking in consideration fc->max_read and gaps
between page indices, but it's not clear whether it's worthy or not.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch reworks fuse_retrieve() to allocate only so many page pointers
as needed. The core part of the patch is the following calculation:
num_pages = (num + offset + PAGE_SIZE - 1) >> PAGE_SHIFT;
(thanks Miklos for formula). All other changes are mostly shuffling lines.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch categorizes all fuse_get_req() invocations into two categories:
- fuse_get_req_nopages(fc) - when caller doesn't care about req->pages
- fuse_get_req(fc, n) - when caller need n page pointers (n > 0)
Adding fuse_get_req_nopages() helps to avoid numerous fuse_get_req(fc, 0)
scattered over code. Now it's clear from the first glance when a caller need
fuse_req with page pointers.
The patch doesn't make any logic changes. In multi-page case, it silly
allocates array of FUSE_MAX_PAGES_PER_REQ page pointers. This will be amended
by future patches.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The patch removes inline array of FUSE_MAX_PAGES_PER_REQ page pointers from
fuse_req. Instead of that, req->pages may now point either to small inline
array or to an array allocated dynamically.
This essentially means that all callers of fuse_request_alloc[_nofs] should
pass the number of pages needed explicitly.
The patch doesn't make any logic changes.
Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
This patch implements readdirplus support in FUSE, similar to NFS.
The payload returned in the readdirplus call contains
'fuse_entry_out' structure thereby providing all the necessary inputs
for 'faking' a lookup() operation on the spot.
If the dentry and inode already existed (for e.g. in a re-run of ls -l)
then just the inode attributes timeout and dentry timeout are refreshed.
With a simple client->network->server implementation of a FUSE based
filesystem, the following performance observations were made:
Test: Performing a filesystem crawl over 20,000 files with
sh# time ls -lR /mnt
Without readdirplus:
Run 1: 18.1s
Run 2: 16.0s
Run 3: 16.2s
With readdirplus:
Run 1: 4.1s
Run 2: 3.8s
Run 3: 3.8s
The performance improvement is significant as it avoided 20,000 upcalls
calls (lookup). Cache consistency is no worse than what already is.
Signed-off-by: Anand V. Avati <avati@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The variables mapping,index are initialized but never used
otherwise, so remove the unused variables.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix the following sparse warning:
fs/fuse/file.c:2249:6: warning: symbol 'fuse_file_fallocate' was not declared. Should it be static?
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Given that CUSE depends on FUSE, it only makes sense to move its
Kconfig entry into the FUSE Kconfig file. Also, add a few grammatical
and semantic touchups.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix the following compiler warnings:
fs/fuse/cuse.c: In function 'cuse_process_init_reply':
fs/fuse/cuse.c:288:24: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
fs/fuse/cuse.c:272:14: note: 'val' was declared here
fs/fuse/cuse.c:284:10: warning: 'key' may be used uninitialized in this function [-Wmaybe-uninitialized]
fs/fuse/cuse.c:272:8: note: 'key' was declared here
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Sysfs doesn't allow two devices with the same name, but we register a
sysfs entry for each cuse device without checking for name collisions.
This extends the registration to first check whether the name was already
registered.
To avoid race-conditions between the name-check and linking the device, we
need to protect the whole registration with a mutex.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
We need to check for name-collisions during cuse-device registration. To
avoid race-conditions, this needs to be protected during the whole device
registration. Therefore, replace the spinlocks by mutexes first so we can
safely extend the locked regions to include more expensive or sleeping
code paths.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Merge misc patches from Andrew Morton:
"Incoming:
- lots of misc stuff
- backlight tree updates
- lib/ updates
- Oleg's percpu-rwsem changes
- checkpatch
- rtc
- aoe
- more checkpoint/restart support
I still have a pile of MM stuff pending - Pekka should be merging
later today after which that is good to go. A number of other things
are twiddling thumbs awaiting maintainer merges."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
scatterlist: don't BUG when we can trivially return a proper error.
docs: update documentation about /proc/<pid>/fdinfo/<fd> fanotify output
fs, fanotify: add @mflags field to fanotify output
docs: add documentation about /proc/<pid>/fdinfo/<fd> output
fs, notify: add procfs fdinfo helper
fs, exportfs: add exportfs_encode_inode_fh() helper
fs, exportfs: escape nil dereference if no s_export_op present
fs, epoll: add procfs fdinfo helper
fs, eventfd: add procfs fdinfo helper
procfs: add ability to plug in auxiliary fdinfo providers
tools/testing/selftests/kcmp/kcmp_test.c: print reason for failure in kcmp_test
breakpoint selftests: print failure status instead of cause make error
kcmp selftests: print fail status instead of cause make error
kcmp selftests: make run_tests fix
mem-hotplug selftests: print failure status instead of cause make error
cpu-hotplug selftests: print failure status instead of cause make error
mqueue selftests: print failure status instead of cause make error
vm selftests: print failure status instead of cause make error
ubifs: use prandom_bytes
mtd: nandsim: use prandom_bytes
...
But the kernel decided to call it "origin" instead. Fix most of the
sites.
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kuid_t and kgid_t in struct fuse_conn and struct fuse_mount_data.
The connection between between a fuse filesystem and a fuse daemon is
established when a fuse filesystem is mounted and provided with a file
descriptor the fuse daemon created by opening /dev/fuse.
For now restrict the communication of uids and gids between the fuse
filesystem and the fuse daemon to the initial user namespace. Enforce
this by verifying the file descriptor passed to the mount of fuse was
opened in the initial user namespace. Ensuring the mount happens in
the initial user namespace is not necessary as mounts from non-initial
user namespaces are not yet allowed.
In fuse_req_init_context convert the currrent fsuid and fsgid into the
initial user namespace for the request that will be sent to the fuse
daemon.
In fuse_fill_attr convert the uid and gid passed from the fuse daemon
from the initial user namespace into kuids and kgids.
In iattr_to_fattr called from fuse_setattr convert kuids and kgids
into the uids and gids in the initial user namespace before passing
them to the fuse filesystem.
In fuse_change_attributes_common called from fuse_dentry_revalidate,
fuse_permission, fuse_geattr, and fuse_setattr, and fuse_iget convert
the uid and gid from the fuse daemon into a kuid and a kgid to store
on the fuse inode.
By default fuse mounts are restricted to task whose uid, suid, and
euid matches the fuse user_id and whose gid, sgid, and egid matches
the fuse group id. Convert the user_id and group_id mount options
into kuids and kgids at mount time, and use uid_eq and gid_eq to
compare the in fuse_allow_task.
Cc: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Move actual pte filling for non-linear file mappings into the new special
vma operation: ->remap_pages().
Filesystems must implement this method to get non-linear mapping support,
if it uses filemap_fault() then generic_file_remap_pages() can be used.
Now device drivers can implement this method and obtain nonlinear vma support.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com> #arch/tile
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason to call rcu_barrier() on every
deactivate_locked_super(). We only need to make sure that all delayed rcu
free inodes are flushed before we destroy related cache.
Removing rcu_barrier() from deactivate_locked_super() affects some fast
paths. E.g. on my machine exit_group() of a last process in IPC
namespace takes 0.07538s. rcu_barrier() takes 0.05188s of that time.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In some cases fuse_retrieve() would return a short byte count if offset was
non-zero. The data returned was correct, though.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
gcc 4.6.3 complains about uninitialized variables in fs/fuse/control.c:
CC fs/fuse/control.o
fs/fuse/control.c: In function 'fuse_conn_congestion_threshold_write':
fs/fuse/control.c:165:29: warning: 'val' may be used uninitialized in this function [-Wuninitialized]
fs/fuse/control.c: In function 'fuse_conn_max_background_write':
fs/fuse/control.c:128:23: warning: 'val' may be used uninitialized in this function [-Wuninitialized]
fuse_conn_limit_write() will always return non-zero unless the &val
is modified, so the warning is misleading. Let the compiler know
about it by marking 'val' with 'uninitialized_var'.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Luca Risolia reported that a CUSE daemon will continue to run even if
initialization of the emulated device failes for some reason (e.g. the device
number is already registered by another driver).
This patch disconnects the fuse device on error, which will make the userspace
CUSE daemon exit, albeit without indication about what the problem was.
Reported-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
fuse_conn_kill() removed fc->entry, called fuse_ctl_remove_conn() and
fuse_bdi_destroy(). None of which is appropriate for cuse cleanup.
The fuse_ctl_remove_conn() decrements the nlink on the control filesystem, which
is totally bogus. The others are harmless but unnecessary.
So move these out from fuse_conn_kill() to fuse_put_super() where they belong.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Pull vfs fixes from Miklos Szeredi.
This mainly fixes some confusion about whether the open 'mode' variable
passed around should contain the full file type (S_IFREG etc)
information or just the permission mode. In particular, the lack of
proper file type information had confused fuse.
* 'vfs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
vfs: fix propagation of atomic_open create error on negative dentry
fuse: check create mode in atomic open
vfs: pass right create mode to may_o_create()
vfs: atomic_open(): fix create mode usage
vfs: canonicalize create mode in build_open_flags()
Verify that the VFS is passing us a complete create mode with the S_IFREG to
atomic open.
Reported-by: Steve <steveamigauk@yahoo.co.uk>
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Commit 7572777eef attempted to verify that
the total iovec from the client doesn't overflow iov_length() but it
only checked the first element. The iovec could still overflow by
starting with a small element. The obvious fix is to check all the
elements.
The overflow case doesn't look dangerous to the kernel as the copy is
limited by the length after the overflow. This fix restores the
intention of returning an error instead of successfully copying less
than the iovec represented.
I found this by code inspection. I built it but don't have a test case.
I'm cc:ing stable because the initial commit did as well.
Signed-off-by: Zach Brown <zab@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: <stable@vger.kernel.org> [2.6.37+]
Convert check in fuse_file_aio_write() to using new freeze protection.
CC: fuse-devel@lists.sourceforge.net
CC: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add missing flags that userspace derived from the protocol version number. This
makes the protocol more flexible.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
A fuse-based network filesystem might allow for the inode
and/or file data to change unexpectedly. A local client
that opens and repeatedly reads a file might never pick
up on such changes and indefinitely return stale data.
Always invoke fuse_update_attributes() in the read path
to cause an attr revalidation when the attributes expire.
This leads to a page cache invalidation if necessary and
ensures fuse issues new read requests to the fuse client.
The original logic (reval only on reads beyond EOF) is
preserved unless the client specifies FUSE_AUTO_INVAL_DATA
on init.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
We currently invalidate the inode address space mapping
if the file size changes unexpectedly. In the case of a
fuse network filesystem, a portion of a file could be
overwritten remotely without changing the file size.
Compare the old mtime as well to detect this condition
and invalidate the mapping if the file has been updated.
The original logic (to ignore changes in mtime) is
preserved unless the client specifies FUSE_AUTO_INVAL_DATA
on init.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
boolean "does it have to be exclusive?" flag is passed instead;
Local filesystem should just ignore it - the object is guaranteed
not to be there yet.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Just the flags; only NFS cares even about that, but there are
legitimate uses for such argument. And getting rid of that
completely would require splitting ->lookup() into a couple
of methods (at least), so let's leave that alone for now...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Just pass struct file *. Methods are happier that way...
There's no need to return struct file * from finish_open() now,
so let it return int. Next: saner prototypes for parts in
namei.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Change of calling conventions:
old new
NULL 1
file 0
ERR_PTR(-ve) -ve
Caller *knows* that struct file *; no need to return it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and let finish_open() report having opened the file via that sucker.
Next step: don't modify od->filp at all.
[AV: FILE_CREATE was already used by cifs; Miklos' fix folded]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add an ->atomic_open implementation which replaces the atomic open+create
operation implemented via ->create. No functionality is changed.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Btrfs has to make sure we have space to allocate new blocks in order to modify
the inode, so updating time can fail. We've gotten around this by having our
own file_update_time but this is kind of a pain, and Christoph has indicated he
would like to make xfs do something different with atime updates. So introduce
->update_time, where we will deal with i_version an a/m/c time updates and
indicate which changes need to be made. The normal version just does what it
has always done, updates the time and marks the inode dirty, and then
filesystems can choose to do something different.
I've gone through all of the users of file_update_time and made them check for
errors with the exception of the fault code since it's complicated and I wasn't
quite sure what to do there, also Jan is going to be pushing the file time
updates into page_mkwrite for those who have it so that should satisfy btrfs and
make it not a big deal to check the file_update_time() return code in the
generic fault path. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
pass inode + parent's inode or NULL instead of dentry + bool saying
whether we want the parent or not.
NOTE: that needs ceph fix folded in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oLXf
-----END PGP SIGNATURE-----
Merge tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
Pull writeback tree from Wu Fengguang:
"Mainly from Jan Kara to avoid iput() in the flusher threads."
* tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Avoid iput() from flusher thread
vfs: Rename end_writeback() to clear_inode()
vfs: Move waiting for inode writeback from end_writeback() to evict_inode()
writeback: Refactor writeback_single_inode()
writeback: Remove wb->list_lock from writeback_single_inode()
writeback: Separate inode requeueing after writeback
writeback: Move I_DIRTY_PAGES handling
writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()
writeback: Move clearing of I_SYNC into inode_sync_complete()
writeback: initialize global_dirty_limit
fs: remove 8 bytes of padding from struct writeback_control on 64 bit builds
mm: page-writeback.c: local functions should not be exposed globally
Don't use inode->i_blkbits which might be stale, instead calculate the blksize
information from the freshly obtained attributes.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Now we store attr->ino at inode->i_ino, return attr->ino at the
first time and then return inode->i_ino if the attribute timeout
isn't expired. That's wrong on 32 bit platforms because attr->ino
is 64 bit and inode->i_ino is 32 bit in this case.
Fix this by saving 64 bit ino in fuse_inode structure and returning
it every time we call getattr. Also squash attr->ino into inode->i_ino
explicitly.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
After we moved inode_sync_wait() from end_writeback() it doesn't make sense
to call the function end_writeback() anymore. Rename it to clear_inode()
which well says what the function really does - set I_CLEAR flag.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
fallocate filesystem operation preallocates media space for the given file.
If fallocate returns success then any subsequent write to the given range
never fails with 'not enough space' error.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
This patch replaces the code for getting an number from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Pull fuse updates from Miklos Szeredi.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use flexible array in fuse.h
fuse: allow nanosecond granularity
fuse: O_DIRECT support for files
fuse: fix nlink after unlink
Derrik Pates reports that an utimensat with a NULL argument results in the
current time being sent from the kernel with 1 second granularity.
Reported-by: Derrik Pates <demon@now.ai>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Implement ->direct_IO() method in aops. The ->direct_IO() method combines
the existing fuse_direct_read/fuse_direct_write methods to implement
O_DIRECT functionality.
Reaching ->direct_IO() in the read path via generic_file_aio_read ensures
proper synchronization with page cache with its existing framework.
Reaching ->direct_IO() in the write path via fuse_file_aio_write is made
to come via generic_file_direct_write() which makes it play nice with
the page cache w.r.t other mmap pages etc.
On files marked 'direct_io' by the filesystem server, IO always follows
the fuse_direct_read/write path. There is no effect of fcntl(O_DIRECT)
and it always succeeds.
On files not marked with 'direct_io' by the filesystem server, the IO
path depends on O_DIRECT flag by the application. This can be passed
at the time of open() as well as via fcntl().
Note that asynchronous O_DIRECT iocb jobs are completed synchronously
always (this has been the case with FUSE even before this patch)
Signed-off-by: Anand Avati <avati@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Anand Avati reports that the following sequence of system calls fail on a fuse
filesystem:
create("filename") => 0
link("filename", "linkname") => 0
unlink("filename") => 0
link("linkname", "filename") => -ENOENT ### BUG ###
vfs_link() fails with ENOENT if i_nlink is zero, this is done to prevent
resurrecting already deleted files.
Fuse clears i_nlink on unlink even if there are other links pointing to the
file.
Reported-by: Anand Avati <avati@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
FUSE: Notifying the kernel of deletion.
fuse: support ioctl on directories
fuse: Use kcalloc instead of kzalloc to allocate array
fuse: llseek optimize SEEK_CUR and SEEK_SET
vfs_create() ignores everything outside of 16bit subset of its
mode argument; switching it to umode_t is obviously equivalent
and it's the only caller of the method
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
vfs_mkdir() gets int, but immediately drops everything that might not
fit into umode_t and that's the only caller of ->mkdir()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Seeing that just about every destructor got that INIT_LIST_HEAD() copied into
it, there is no point whatsoever keeping this INIT_LIST_HEAD in inode_init_once();
the cost of taking it into inode_init_always() will be negligible for pipes
and sockets and negative for everything else. Not to mention the removal of
boilerplate code from ->destroy_inode() instances...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allows a FUSE file-system to tell the kernel when a file or directory is
deleted. If the specified dentry has the specified inode number, the kernel will
unhash it.
The current 'fuse_notify_inval_entry' does not cause the kernel to clean up
directories that are in use properly, and as a result the users of those
directories see incorrect semantics from the file-system. The error condition
seen when 'fuse_notify_inval_entry' is used to notify of a deleted directory is
avoided when 'fuse_notify_delete' is used instead.
The following scenario demonstrates the difference:
1. User A chdirs into 'testdir' and starts reading 'testfile'.
2. User B rm -rf 'testdir'.
3. User B creates 'testdir'.
4. User C chdirs into 'testdir'.
If you run the above within the same machine on any file-system (including fuse
file-systems), there is no problem: user C is able to chdir into the new
testdir. The old testdir is removed from the dentry tree, but still open by user
A.
If operations 2 and 3 are performed via the network such that the fuse
file-system uses one of the notify functions to tell the kernel that the nodes
are gone, then the following error occurs for user C while user A holds the
original directory open:
muirj@empacher:~> ls /test/testdir
ls: cannot access /test/testdir: No such file or directory
The issue here is that the kernel still has a dentry for testdir, and so it is
requesting the attributes for the old directory, while the file-system is
responding that the directory no longer exists.
If on the other hand, if the file-system can notify the kernel that the
directory is deleted using the new 'fuse_notify_delete' function, then the above
ls will find the new directory as expected.
Signed-off-by: John Muir <john@jmuir.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Multiplexing filesystems may want to support ioctls on the underlying
files and directores (e.g. FS_IOC_{GET,SET}FLAGS).
Ioctl support on directories was missing so add it now.
Reported-by: Antonio SJ Musumeci <bile@landofbile.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Use generic_file_llseek() instead of open coding the seek function.
i_mutex protection is only necessary for SEEK_END (and SEEK_HOLE, SEEK_DATA), so
move SEEK_CUR and SEEK_SET out from under i_mutex.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix race between lseek(fd, 0, SEEK_CUR) and read/write. This was fixed in
generic code by commit 5b6f1eb97d (vfs: lseek(fd, 0, SEEK_CUR) race condition).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The test in fuse_file_llseek() "not SEEK_CUR or not SEEK_SET" always evaluates
to true.
This was introduced in 3.1 by commit 06222e49 (fs: handle SEEK_HOLE/SEEK_DATA
properly in all fs's that define their own llseek) and changed the behavior of
SEEK_CUR and SEEK_SET to always retrieve the file attributes. This is a
performance regression.
Fix the test so that it makes sense.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org
CC: Josef Bacik <josef@redhat.com>
CC: Al Viro <viro@zeniv.linux.org.uk>
Fix two bugs in fuse_retrieve():
- retrieving more than one page would yield repeated instances of the
first page
- if more than FUSE_MAX_PAGES_PER_REQ pages were requested than the
request page array would overflow
fuse_retrieve() was added in 2.6.36 and these bugs had been there since the
beginning.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Replace remaining direct i_nlink updates with a new set_nlink()
updater function.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some files were using the complete module.h infrastructure without
actually including the header at all. Fix them up in advance so
once the implicit presence is removed, we won't get failures like this:
CC [M] fs/nfsd/nfssvc.o
fs/nfsd/nfssvc.c: In function 'nfsd_create_serv':
fs/nfsd/nfssvc.c:335: error: 'THIS_MODULE' undeclared (first use in this function)
fs/nfsd/nfssvc.c:335: error: (Each undeclared identifier is reported only once
fs/nfsd/nfssvc.c:335: error: for each function it appears in.)
fs/nfsd/nfssvc.c: In function 'nfsd':
fs/nfsd/nfssvc.c:555: error: implicit declaration of function 'module_put_and_exit'
make[3]: *** [fs/nfsd/nfssvc.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 37fb3a30b4 ("fuse: fix flock") added in 3.1-rc4 caused flock() to
fail with ENOSYS with the kernel ABI version 7.16 or earlier.
Fix by falling back to testing FUSE_POSIX_LOCKS for ABI versions 7.16
and earlier.
Reported-by: Martin Ziegler <ziegler@email.mathematik.uni-freiburg.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Martin Ziegler <ziegler@email.mathematik.uni-freiburg.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
fuse: mark pages accessed when written to
fuse: delete dead .write_begin and .write_end aops
fuse: fix flock
fuse: fix non-ANSI void function notation
FUSE_NOTIFY_INVAL_ENTRY didn't check the length of the write so the
message processing could overrun and result in a "kernel BUG at
fs/fuse/dev.c:629!"
Reported-by: Han-Wen Nienhuys <hanwenn@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
As fuse does not use the page cache library functions when userspace
writes to a file, it did not benefit from 'c8236db mm: mark page
accessed before we write_end()' that made sure pages are properly
marked accessed when written to.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Ever since 'ea9b990 fuse: implement perform_write', the .write_begin
and .write_end aops have been dead code.
Their task - acquiring a page from the page cache, sending out a write
request and releasing the page again - is now done batch-wise to
maximize the number of pages send per userspace request.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Commit a9ff4f87 "fuse: support BSD locking semantics" overlooked a
number of issues with supporing flock locks over existing POSIX
locking infrastructure:
- it's not backward compatible, passing flock(2) calls to userspace
unconditionally (if userspace sets FUSE_POSIX_LOCKS)
- it doesn't cater for the fact that flock locks are automatically
unlocked on file release
- it doesn't take into account the fact that flock exclusive locks
(write locks) don't need an fd opened for write.
The last one invalidates the original premise of the patch that flock
locks can be emulated with POSIX locks.
This patch fixes the first two issues. The last one needs to be fixed
in userspace if the filesystem assumed that a write lock will happen
only on a file operned for write (as in the case of the current fuse
library).
Reported-by: Sebastian Pipping <webmaster@hartwork.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'for-3.1' of git://linux-nfs.org/~bfields/linux:
nfsd: don't break lease on CLAIM_DELEGATE_CUR
locks: rename lock-manager ops
nfsd4: update nfsv4.1 implementation notes
nfsd: turn on reply cache for NFSv4
nfsd4: call nfsd4_release_compoundargs from pc_release
nfsd41: Deny new lock before RECLAIM_COMPLETE done
fs: locks: remove init_once
nfsd41: check the size of request
nfsd41: error out when client sets maxreq_sz or maxresp_sz too small
nfsd4: fix file leak on open_downgrade
nfsd4: remember to put RW access on stateid destruction
NFSD: Added TEST_STATEID operation
NFSD: added FREE_STATEID operation
svcrpc: fix list-corrupting race on nfsd shutdown
rpc: allow autoloading of gss mechanisms
svcauth_unix.c: quiet sparse noise
svcsock.c: include sunrpc.h to quiet sparse noise
nfsd: Remove deprecated nfsctl system call and related code.
NFSD: allow OP_DESTROY_CLIENTID to be only op in COMPOUND
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers. Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2. For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This converts everybody to handle SEEK_HOLE/SEEK_DATA properly. In some cases
we just return -EINVAL, in others we do the normal generic thing, and in others
we're simply making sure that the properly due-dilligence is done. For example
in NFS/CIFS we need to make sure the file size is update properly for the
SEEK_HOLE and SEEK_DATA case, but since it calls the generic llseek stuff itself
that is all we have to do. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Both the filesystem and the lock manager can associate operations with a
lock. Confusingly, one of them (fl_release_private) actually has the
same name in both operation structures.
It would save some confusion to give the lock-manager ops different
names.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
its value depends only on inode and does not change; we might as
well store it in ->i_op->check_acl and be done with that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Caching "we have already removed suid/caps" was overenthusiastic as merged.
On network filesystems we might have had suid/caps set on another client,
silently picked by this client on revalidate, all of that *without* clearing
the S_NOSEC flag.
AFAICS, the only reasonably sane way to deal with that is
* new superblock flag; unless set, S_NOSEC is not going to be set.
* local block filesystems set it in their ->mount() (more accurately,
mount_bdev() does, so does btrfs ->mount(), users of mount_bdev() other than
local block ones clear it)
* if any network filesystem (or a cluster one) wants to use S_NOSEC,
it'll need to set MS_NOSEC in sb->s_flags *AND* take care to clear S_NOSEC when
inode attribute changes are picked from other clients.
It's not an earth-shattering hole (anybody that can set suid on another client
will almost certainly be able to write to the file before doing that anyway),
but it's a bug that needs fixing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix void function parameter list sparse warning:
fs/fuse/inode.c:74:44: warning: non-ANSI function declaration of function 'fuse_alloc_forget'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fuse has no problems with references to unlinked directories.
CC: Miklos Szeredi <miklos@szeredi.hu>
CC: fuse-devel@lists.sourceforge.net
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (25 commits)
cifs: remove unnecessary dentry_unhash on rmdir/rename_dir
ocfs2: remove unnecessary dentry_unhash on rmdir/rename_dir
exofs: remove unnecessary dentry_unhash on rmdir/rename_dir
nfs: remove unnecessary dentry_unhash on rmdir/rename_dir
ext2: remove unnecessary dentry_unhash on rmdir/rename_dir
ext3: remove unnecessary dentry_unhash on rmdir/rename_dir
ext4: remove unnecessary dentry_unhash on rmdir/rename_dir
btrfs: remove unnecessary dentry_unhash in rmdir/rename_dir
ceph: remove unnecessary dentry_unhash calls
vfs: clean up vfs_rename_other
vfs: clean up vfs_rename_dir
vfs: clean up vfs_rmdir
vfs: fix vfs_rename_dir for FS_RENAME_DOES_D_MOVE filesystems
libfs: drop unneeded dentry_unhash
vfs: update dentry_unhash() comment
vfs: push dentry_unhash on rename_dir into file systems
vfs: push dentry_unhash on rmdir into file systems
vfs: remove dget() from dentry_unhash()
vfs: dentry_unhash immediately prior to rmdir
vfs: Block mmapped writes while the fs is frozen
...
Only a few file systems need this. Start by pushing it down into each
rename method (except gfs2 and xfs) so that it can be dealt with on a
per-fs basis.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only a few file systems need this. Start by pushing it down into each
fs rmdir method (except gfs2 and xfs) so it can be dealt with on a per-fs
basis.
This does not change behavior for any in-tree file systems.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some cases (e.g. ecryptfs) can call ->dentry_revalidate with NULL
nameidata.
https://bugzilla.kernel.org/show_bug.cgi?id=34732
Tyler Hicks pointed out that this bug was introduced by commit
e7c0a16786 "fuse: make fuse_dentry_revalidate() RCU aware"
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
This function basically does:
remove_from_page_cache(old);
page_cache_release(old);
add_to_page_cache_locked(new);
Except it does this atomically, so there's no possibility for the "add" to
fail because of a race.
If memory cgroups are enabled, then the memory cgroup charge is also moved
from the old page to the new.
This function is currently used by fuse to move pages into the page cache
on read, instead of copying the page contents.
[minchan.kim@gmail.com: add freepage() hook to replace_page_cache_page()]
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only bail out of fuse_dentry_revalidate() on LOOKUP_RCU when blocking
is actually necessary.
CC: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Only bail out of fuse_permission() on IPERM_FLAG_RCU when blocking is
actually necessary.
CC: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
If a fuse dev connection is broken, wake up any
processes that are blocking, in a poll system call,
on one of the files in the now defunct filesystem.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reduce the size of struct fuse_request by removing cuse_init_out from
the request structure and allocating it dinamically instead.
CC: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
The exportfs encode handle function should return the minimum required
handle size. This helps user to find out the handle size by passing 0
handle size in the first step and then redoing to the call again with
the returned handle size value.
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit e1181ee6 "vfs: pass struct file to do_truncate on O_TRUNC
opens" broke the behavior of open(O_TRUNC|O_RDONLY) in fuse. Fuse
assumed that when called from open, a truncate() will be done, not an
ftruncate().
Fix by restoring the old behavior, based on the ATTR_OPEN flag.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Single threaded NTFS-3G could get stuck if a delayed RELEASE reply
triggered a DESTROY request via path_put().
Fix this by
a) making RELEASE requests synchronous, whenever possible, on fuseblk
filesystems
b) if not possible (triggered by an asynchronous read/write) then do
the path_put() in a separate thread with schedule_work().
Reported-by: Oliver Neukum <oneukum@suse.de>
Cc: stable@kernel.org
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix ioctl ABI
fuse: allow batching of FORGET requests
fuse: separate queue for FORGET requests
fuse: ioctl cleanup
Fix up trivial conflict in fs/fuse/inode.c due to RCU lookup having done
the RCU-freeing of the inode in fuse_destroy_inode().
Require filesystems be aware of .d_revalidate being called in rcu-walk
mode (nd->flags & LOOKUP_RCU). For now do a simple push down, returning
-ECHILD from all implementations.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Reduce some branches and memory accesses in dcache lookup by adding dentry
flags to indicate common d_ops are set, rather than having to check them.
This saves a pointer memory access (dentry->d_op) in common path lookup
situations, and saves another pointer load and branch in cases where we
have d_op but not the particular operation.
Patched with:
git grep -E '[.>]([[:space:]])*d_op([[:space:]])*=' | xargs sed -e 's/\([^\t ]*\)->d_op = \(.*\);/d_set_d_op(\1, \2);/' -e 's/\([^\t ]*\)\.d_op = \(.*\);/d_set_d_op(\&\1, \2);/' -i
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
RCU free the struct inode. This will allow:
- Subsequent store-free path walking patch. The inode must be consulted for
permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
to take i_lock no longer need to take sb_inode_list_lock to walk the list in
the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
page lock to follow page->mapping.
The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.
In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.
The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
In kernel ABI version 7.16 and later FUSE_IOCTL_RETRY reply from a
unrestricted IOCTL request shall return with an array of 'struct
fuse_ioctl_iovec' instead of 'struct iovec'. This fixes the ABI
ambiguity of 32bit vs. 64bit.
Reported-by: "ccmail111" <ccmail111@yahoo.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Tejun Heo <tj@kernel.org>
Terje Malmedal reports that a fuse filesystem with 32 million inodes
on a machine with lots of memory can take up to 30 minutes to process
FORGET requests when all those inodes are evicted from the icache.
To solve this, create a BATCH_FORGET request that allows up to about
8000 FORGET requests to be sent in a single message.
This request is only sent if userspace supports interface version 7.16
or later, otherwise fall back to sending individual FORGET messages.
Reported-by: Terje Malmedal <terje.malmedal@usit.uio.no>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Terje Malmedal reports that a fuse filesystem with 32 million inodes
on a machine with lots of memory can go unresponsive for up to 30
minutes when all those inodes are evicted from the icache.
The reason is that FORGET messages, sent when the inode is evicted,
are queued up together with regular filesystem requests, and while the
huge queue of FORGET messages are processed no other filesystem
operation can proceed.
Since a full fuse request structure is allocated for each inode, these
take up quite a bit of memory as well.
To solve these issues, create a slim 'fuse_forget_link' structure
containing just the minimum of information required to send the FORGET
request and chain these on a separate queue.
When userspace is asking for a request make sure that FORGET and
non-FORGET requests are selected fairly: for each 8 non-FORGET allow
16 FORGET requests. This will make sure FORGETs do not pile up, yet
other requests are also allowed to proceed while the queued FORGETs
are processed.
Reported-by: Terje Malmedal <terje.malmedal@usit.uio.no>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Verify that the total length of the iovec returned in FUSE_IOCTL_RETRY
doesn't overflow iov_length().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: <stable@kernel.org> [2.6.31+]
If a 32bit CUSE server is run on 64bit this results in EIO being
returned to the caller.
The reason is that FUSE_IOCTL_RETRY reply was defined to use 'struct
iovec', which is different on 32bit and 64bit archs.
Work around this by looking at the size of the reply to determine
which struct was used. This is only needed if CONFIG_COMPAT is
defined.
A more permanent fix for the interface will be to use the same struct
on both 32bit and 64bit.
Reported-by: "ccmail111" <ccmail111@yahoo.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: <stable@kernel.org> [2.6.31+]
The attribute cache for a file was not being cleared when a file is opened
with O_TRUNC.
If the filesystem's open operation truncates the file ("atomic_o_trunc"
feature flag is set) then the kernel should invalidate the cached st_mtime
and st_ctime attributes.
Also i_size should be explicitly be set to zero as it is used sometimes
without refreshing the cache.
Signed-off-by: Ken Sumrall <ksumrall@android.com>
Cc: Anfei <anfei.zhou@gmail.com>
Cc: "Anand V. Avati" <avati@gluster.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace iterated page_cache_release() with release_pages(), which is
faster and shorter.
Needs release_pages() to be exported to modules.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
split invalidate_inodes()
fs: skip I_FREEING inodes in writeback_sb_inodes
fs: fold invalidate_list into invalidate_inodes
fs: do not drop inode_lock in dispose_list
fs: inode split IO and LRU lists
fs: switch bdev inode bdi's correctly
fs: fix buffer invalidation in invalidate_list
fsnotify: use dget_parent
smbfs: use dget_parent
exportfs: use dget_parent
fs: use RCU read side protection in d_validate
fs: clean up dentry lru modification
fs: split __shrink_dcache_sb
fs: improve DCACHE_REFERENCED usage
fs: use percpu counter for nr_dentry and nr_dentry_unused
fs: simplify __d_free
fs: take dcache_lock inside __d_path
fs: do not assign default i_ino in new_inode
fs: introduce a per-cpu last_ino allocator
new helper: ihold()
...
Commit 7909b1c640 ("fuse: don't use atomic kmap") removed KM_USER0 usage
from fuse/dev.c. Switch KM_USER1 uses to KM_USER0 for clarity. Also
replace open coded clear_highpage().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After all that's what they are intended for.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of always assigning an increasing inode number in new_inode
move the call to assign it into those callers that actually need it.
For now callers that need it is estimated conservatively, that is
the call is added to all filesystems that do not assign an i_ino
by themselves. For a few more filesystems we can avoid assigning
any inode number given that they aren't user visible, and for others
it could be done lazily when an inode number is actually needed,
but that's left for later patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
fs/fuse/dev.c:1357: warning: ‘total_len’ may be used uninitialized in this
function
Initialize total_len to zero, else its value will be undefined.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Sparse doesn't understand lock annotations of the form
__releases(&foo->lock). Change them to __releases(foo->lock). Same
for __acquires().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
David Bartly reported that fuse can hang in fuse_get_req_nofail() when
the connection to the filesystem server is no longer active.
If bg_queue is not empty then flush_bg_queue() called from
request_end() can put more requests on to the pending queue. If this
happens while ending requests on the processing queue then those
background requests will be queued to the pending list and never
ended.
Another problem is that fuse_dev_release() didn't wake up processes
sleeping on blocked_waitq.
Solve this by:
a) flushing the background queue before calling end_requests() on the
pending and processing queues
b) setting blocked = 0 and waking up processes waiting on
blocked_waitq()
Thanks to David for an excellent bug report.
Reported-by: David Bartley <andareed@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
Make sure we check the truncate constraints early on in ->setattr by adding
those checks to inode_change_ok. Also clean up and document inode_change_ok
to make this obvious.
As a fallout we don't have to call inode_newsize_ok from simple_setsize and
simplify it down to a truncate_setsize which doesn't return an error. This
simplifies a lot of setattr implementations and means we use truncate_setsize
almost everywhere. Get rid of fat_setsize now that it's trivial and mark
ext2_setsize static to make the calling convention obvious.
Keep the inode_newsize_ok in vmtruncate for now as all callers need an
audit for its removal anyway.
Note: setattr code in ecryptfs doesn't call inode_change_ok at all and
needs a deeper audit, but that is left for later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make sure we call inode_change_ok before doing any changes in ->setattr,
and make sure to call it even if our fs wants to ignore normal UNIX
permissions, but use the ATTR_FORCE to skip those.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently MAY_ACCESS means that filesystems must check the permissions
right then and not rely on cached results or the results of future
operations on the object. This can be because of a call to sys_access() or
because of a call to chdir() which needs to check search without relying on
any future operations inside that dir. I plan to use MAY_ACCESS for other
purposes in the security system, so I split the MAY_ACCESS and the
MAY_CHDIR cases.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen D. Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Userspace filesystem can request data to be retrieved from the inode's
mapping. This request is synchronous and the retrieved data is queued
as a new request. If the write to the fuse device returns an error
then the retrieve request was not completed and a reply will not be
sent.
Only present pages are returned in the retrieve reply. Retrieving
stops when it finds a non-present page and only data prior to that is
returned.
This request doesn't change the dirty state of pages.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Userspace filesystem can request data to be stored in the inode's
mapping. This request is synchronous and has no reply. If the write
to the fuse device returns an error then the store request was not
fully completed (but may have updated some pages).
If the stored data overflows the current file size, then the size is
extended, similarly to a write(2) on the filesystem.
Pages which have been completely stored are marked uptodate.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Don't use atomic kmap for mapping userspace buffers in device
read/write/splice.
This is necessary because the next patch (adding store notify)
requires that caller of fuse_copy_page() may sleep between
invocations. The simplest way to ensure this is to change the atomic
kmaps to non-atomic ones.
Thankfully architectures where kmap() is not a no-op are going out of
fashion, so we can ignore the (probably negligible) performance impact
of this change.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
mm: export generic_pipe_buf_*() to modules
fuse: support splice() reading from fuse device
fuse: allow splice to move pages
mm: export remove_from_page_cache() to modules
mm: export lru_cache_add_*() to modules
fuse: support splice() writing to fuse device
fuse: get page reference for readpages
fuse: use get_user_pages_fast()
fuse: remove unneeded variable
This adds:
alias: devname:<name>
to some common kernel modules, which will allow the on-demand loading
of the kernel module when the device node is accessed.
Ideally all these modules would be compiled-in, but distros seems too
much in love with their modularization that we need to cover the common
cases with this new facility. It will allow us to remove a bunch of pretty
useless init scripts and modprobes from init scripts.
The static device node aliases will be carried in the module itself. The
program depmod will extract this information to a file in the module directory:
$ cat /lib/modules/2.6.34-00650-g537b60d-dirty/modules.devname
# Device nodes to trigger on-demand module loading.
microcode cpu/microcode c10:184
fuse fuse c10:229
ppp_generic ppp c108:0
tun net/tun c10:200
dm_mod mapper/control c10:235
Udev will pick up the depmod created file on startup and create all the
static device nodes which the kernel modules specify, so that these modules
get automatically loaded when the device node is accessed:
$ /sbin/udevd --debug
...
static_dev_create_from_modules: mknod '/dev/cpu/microcode' c10:184
static_dev_create_from_modules: mknod '/dev/fuse' c10:229
static_dev_create_from_modules: mknod '/dev/ppp' c108:0
static_dev_create_from_modules: mknod '/dev/net/tun' c10:200
static_dev_create_from_modules: mknod '/dev/mapper/control' c10:235
udev_rules_apply_static_dev_perms: chmod '/dev/net/tun' 0666
udev_rules_apply_static_dev_perms: chmod '/dev/fuse' 0666
A few device nodes are switched to statically allocated numbers, to allow
the static nodes to work. This might also useful for systems which still run
a plain static /dev, which is completely unsafe to use with any dynamic minor
numbers.
Note:
The devname aliases must be limited to the *common* and *single*instance*
device nodes, like the misc devices, and never be used for conceptually limited
systems like the loop devices, which should rather get fixed properly and get a
control node for losetup to talk to, instead of creating a random number of
device nodes in advance, regardless if they are ever used.
This facility is to hide the mess distros are creating with too modualized
kernels, and just to hide that these modules are not compiled-in, and not to
paper-over broken concepts. Thanks! :)
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Ian Kent <raven@themaw.net>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow userspace filesystem implementation to use splice() to read from
the fuse device.
The userspace filesystem can now transfer data coming from a WRITE
request to an arbitrary file descriptor (regular file, block device or
socket) without having to go through a userspace buffer.
The semantics of using splice() to read messages are:
1) with a single splice() call move the whole message from the fuse
device to a temporary pipe
2) read the header from the pipe and determine the message type
3a) if message is a WRITE then splice data from pipe to destination
3b) else read rest of message to userspace buffer
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
When splicing buffers to the fuse device with SPLICE_F_MOVE, try to
move pages from the pipe buffer into the page cache. This allows
populating the fuse filesystem's cache without ever touching the page
contents, i.e. zero copy read capability.
The following steps are performed when trying to move a page into the
page cache:
- buf->ops->confirm() to make sure the new page is uptodate
- buf->ops->steal() to try to remove the new page from it's previous place
- remove_from_page_cache() on the old page
- add_to_page_cache_locked() on the new page
If any of the above steps fail (non fatally) then the code falls back
to copying the page. In particular ->steal() will fail if there are
external references (other than the page cache and the pipe buffer) to
the page.
Also since the remove_from_page_cache() + add_to_page_cache_locked()
are non-atomic it is possible that the page cache is repopulated in
between the two and add_to_page_cache_locked() will fail. This could
be fixed by creating a new atomic replace_page_cache_page() function.
fuse_readpages_end() needed to be reworked so it works even if
page->mapping is NULL for some or all pages which can happen if the
add_to_page_cache_locked() failed.
A number of sanity checks were added to make sure the stolen pages
don't have weird flags set, etc... These could be moved into generic
splice/steal code.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Allow userspace filesystem implementation to use splice() to write to
the fuse device. The semantics of using splice() are:
1) buffer the message header and data in a temporary pipe
2) with a *single* splice() call move the message from the temporary pipe
to the fuse device
The READ reply message has the most interesting use for this, since
now the data from an arbitrary file descriptor (which could be a
regular file, a block device or a socket) can be tranferred into the
fuse device without having to go through a userspace buffer. It will
also allow zero copy moving of pages.
One caveat is that the protocol on the fuse device requires the length
of the whole message to be written into the header. But the length of
the data transferred into the temporary pipe may not be known in
advance. The current library implementation works around this by
using vmplice to write the header and modifying the header after
splicing the data into the pipe (error handling omitted):
struct fuse_out_header out;
iov.iov_base = &out;
iov.iov_len = sizeof(struct fuse_out_header);
vmsplice(pip[1], &iov, 1, 0);
len = splice(input_fd, input_offset, pip[1], NULL, len, 0);
/* retrospectively modify the header: */
out.len = len + sizeof(struct fuse_out_header);
splice(pip[0], NULL, fuse_chan_fd(req->ch), NULL, out.len, flags);
This works since vmsplice only saves a pointer to the data, it does
not copy the data itself.
Since pipes are currently limited to 16 pages and messages need to be
spliced atomically, the length of the data is limited to 15 pages (or
60kB for 4k pages).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acquire a page ref on pages in ->readpages() and release them when the
read has finished. Not acquiring a reference didn't seem to cause any
trouble since the page is locked and will not be kicked out of the
page cache during the read.
However the following patches will want to remove the page from the
cache so a separate ref is needed. Making the reference in req->pages
explicit also makes the code easier to understand.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Replace uses of get_user_pages() with get_user_pages_fast(). It looks
nicer and should be faster in most cases.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
"map" isn't needed any more after: 0bd87182d3 "fuse: fix kunmap in
fuse_ioctl_copy_user"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
gcc 4.4 warns about:
fs/fuse/dev.c: In function ‘fuse_notify_inval_entry’:
fs/fuse/dev.c:925: warning: the frame size of 1060 bytes is larger than 1024 bytes
The problem is we declare two structures and a large array on the stack,
I move the array alway from the stack and allocate memory for it dynamically.
Signed-off-by: Fang Wenqi <antonf@turbolinux.com.cn>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
