DDR3 SDRAM Standard (JESD79-3F) defines some standard speed bins for
DDR3 memories. The rk3399_dmc driver allows you to pass these values via
the device tree. For that purpose the devfreq/rk3399_dmc.txt binding
refers to a ddr.h file which does not exist. This patch adds the missing
defines in a include file called rk3399-ddr.h with the definition of
standard speed bins according to the ARM Trusted Firmware (ATF).
Fixes: c1ceb8f7c1 (Documentation: bindings: add dt documentation for rk3399 dmc)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit f5a4670de9 ("clk: imx: Add new clo01 and clo2 controlled
by CCOSR") introduced the CLK_CLKO definitions, but didn't put them
at the end of the list, which may cause dtb breakage when running an old
dtb with a newer kernel.
In order to avoid that, simply add the new CLK_CKO clock definitions
at the end of the list.
Fixes: f5a4670de9 ("clk: imx: Add new clo01 and clo2 controlled by CCOSR")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-qcom-sdm845:
clk: qcom: Export clk_fabia_pll_configure()
clk: qcom: Add video clock controller driver for SDM845
dt-bindings: clock: Introduce QCOM Video clock bindings
clk: qcom: Add Global Clock controller (GCC) driver for SDM845
clk: qcom: Add DT bindings for SDM845 gcc clock controller
clk: qcom: Configure the RCGs to a safe source as needed
clk: qcom: Add support for BRANCH_HALT_SKIP flag for branch clocks
clk: qcom: Simplify gdsc status checking logic
clk: qcom: gdsc: Add support to poll CFG register to check GDSC state
clk: qcom: gdsc: Add support to poll for higher timeout value
clk: qcom: gdsc: Add support to reset AON and block reset logic
clk: qcom: Add support for controlling Fabia PLL
clk: qcom: Clear hardware clock control bit of RCG
Also fixup the Kconfig mess where SDM845 GCC has msm8998 in the
description and also the video Kconfig says things slightly differently
from the GCC one so just make it the same.
* clk-match-string:
clk: use match_string() helper
clk: bcm2835: use match_string() helper
* clk-ingenic:
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
* clk-si544-round-fix:
clk-si544: Properly round requested frequency to nearest match
* clk-bcm-stingray:
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
* clk-imx7d:
clk: imx7d: reset parent for mipi csi root
clk: imx7d: fix mipi dphy div parent
* clk-hisi-stub:
clk/driver/hisi: Consolidate the Kconfig for the CLOCK_STUB
* clk-mvebu:
clk: mvebu: use correct bit for 98DX3236 NAND
* clk-imx6-epit:
clk: imx6: add EPIT clock support
* clk-debugfs-simple:
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
* clk-qcom-rpmh:
dt-bindings: clock: Introduce QCOM RPMh clock bindings
* clk-npcm7xx:
clk: npcm7xx: fix return value check in npcm7xx_clk_init()
clk: npcm7xx: add clock controller
dt-binding: clk: npcm750: Add binding for Nuvoton NPCM7XX Clock
* clk-of-parent-count:
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
soc/tegra: pmc: Use of_clk_get_parent_count() instead of open coding
soc: rockchip: power-domain: Use of_clk_get_parent_count() instead of open coding
ARM: timer-sp: Use of_clk_get_parent_count() instead of open coding
clk: Extract OF clock helpers in <linux/of_clk.h>
* clk-qcom-rcg-fix:
clk: qcom: Base rcg parent rate off plan frequency
Update Stingray clock binding document to add additional clock entries
with names matching the latest ASIC datasheet. Also modify a few existing
entries to make their naming more consistent with the rest of the entries
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add EPIT clock support to the i.MX6Q clocking infrastructure.
Signed-off-by: Colin Didier <colin.didier@devialet.com>
Signed-off-by: Clément Peron <clement.peron@devialet.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a 24MHz fixed clock.
This clock will be used for certain devices, e.g. pwm.
Signed-off-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Correct enet clock gates as below:
CCGR6: IMX7D_ENET_AXI_ROOT_CLK (enet1 and enet2 bus clocks)
CCGR112: IMX7D_ENET1_TIME_ROOT_CLK, IMX7D_ENET1_IPG_ROOT_CLK
CCGR113: IMX7D_ENET2_TIME_ROOT_CLK, IMX7D_ENET2_IPG_ROOT_CLK
Just rename unused IMX7D_ENETx_REF_ROOT_CLK for
IMX7D_ENETx_IPG_ROOT_CLK instead of adding new clocks.
Based on Andy Duan's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for video clock controller for
Qualcomm Technology Inc's SoCs.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Just add binding for a required clock referenced by Mali-450 on MT7623
or MT2701 SoC.
Cc: devicetree@vger.kernel.org
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The hdmitx_dig_cts clock signal is not a child of clk26m,
and the actual output of the PLL block is derived from
the tvdpll via a configurable PLL post-divider.
It is used as the PLL reference input to the HDMI PHY module.
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Signed-off-by: Chunhui Dai <chunhui.dai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are two USB3 host controllers on Hi3798CV200 SoC.
This commit adds missing clocks for them.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This commit fixes incorrect setting of reset bits for PCI/VGA and
PECI modules.
1. Reset bit for PCI/VGA is 8.
2. PECI reset bit is missing so added bit 10 as its reset bit.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ast2500 has an additional reset register that contains resets not
present in the ast2400. This enables support for this register, and adds
the one reset line that is controlled by it.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add dt-bindings headers for the Meson-AXG's AO clock and
reset controller.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add compatible string and the include file for gcc clock
controller for SDM845.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has lvds2 (analog clock2), an I/O clock like lvds1.
And this lvds2, along with lvds1, can be used to provide
external clock source to the internal pll, such as pll4_audio
and pll5_video.
This patch mainly adds the lvds2 to the clock tree and fix its
relationship with pll accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The H6 has clock/reset controls in PRCM part, like old SoCs such as H3
and A64. However, the PRCM CCU is rearranged; the register arragement
is now similar to the main CCU of H6, and the PRCM now has two APB
buses to control -- one is clocked from AHB clock derivde from AR100
clock, the other is clocked from the same mux with AR100 clock.
Therefore a new driver is written for it.
As there's no official document about the PRCM in H6, all the information
are indirectly collected from BSP and parts of the document, and the
information source is noted as comments in the driver's source code. If
reliable information is provided furtherly, the driver needs to be
rechecked.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add RPMh clock device bindings for Qualcomm Technology Inc's SoCs. These
devices would be used for communicating resource state requests to control
the clocks managed by RPMh.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Export the NAND clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This patch adds all R-Car E3 Clock Pulse Generator Core Clock Outputs.
Note that internal CPG clocks (S0, S1, S2, S3, SDSRC, POST3) are not
included, as they are used as internal clock sources only, and never
referenced from DT.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the global clock controller found on MSM8998
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Specify regs for alpha_plls, fix white spaces and add binding]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add all RZ/G1C Clock Pulse Generator Core Clock Outputs, as listed in
Table 7.2 ("List of Clocks [RZ/G1C]") of the RZ/G1C Hardware User's
Manual.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
[geert: Use consecutive numbering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----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=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
It's recommended to use only clk_sys_dbg clock instead to activate
debug IP.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds tzc2 clock and rename tzc clock into tzc1
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-davinci:
clk: davinci: Remove redundant dev_err calls
clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks
clk: davinci: New driver for TI DA8XX CFGCHIP clocks
dt-bindings: clock: Add bindings for DA8XX CFGCHIP clocks
clk: davinci: Add platform information for TI DM646x PSC
clk: davinci: Add platform information for TI DM644x PSC
clk: davinci: Add platform information for TI DM365 PSC
clk: davinci: Add platform information for TI DM355 PSC
clk: davinci: Add platform information for TI DA850 PSC
clk: davinci: Add platform information for TI DA830 PSC
clk: davinci: New driver for davinci PSC clocks
dt-bindings: clock: New bindings for TI Davinci PSC
clk: davinci: Add platform information for TI DM646x PLL
clk: davinci: Add platform information for TI DM644x PLL
clk: davinci: Add platform information for TI DM365 PLL
clk: davinci: Add platform information for TI DM355 PLL
clk: davinci: Add platform information for TI DA850 PLL
clk: davinci: Add platform information for TI DA830 PLL
clk: davinci: New driver for davinci PLL clocks
dt-bindings: clock: Add new bindings for TI Davinci PLL clocks
* clk-si544:
clk: Add driver for the si544 clock generator chip
* clk-rockchip:
clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
clk: rockchip: Fix error return in phase clock registration
clk: rockchip: Correct the behaviour of restoring cached phase
clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
clk: rockchip: Add 1.6GHz PLL rate for rk3399
clk: rockchip: Restore the clock phase after the rate was changed
clk: rockchip: Prevent calculating mmc phase if clock rate is zero
clk: rockchip: Free the memory on the error path
clk: rockchip: document hdmi_phy external input for rk3328
clk: rockchip: add flags for rk3328 dclk_lcdc
clk: rockchip: remove ignore_unused flag from rk3328 vio_h2p clocks
clk: rockchip: protect all remaining rk3328 interconnect clocks
clk: rockchip: export sclk_hdmi_sfc on rk3328
clk: rockchip: remove HCLK_VIO from rk3328 dt header
clk: rockchip: fix hclk_vio_niu on rk3328
* clk-uniphier:
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: uniphier: add ethernet clock control support for PXs3
clk: uniphier: add Pro4/Pro5/PXs2 audio system clock
* clk-ti-flag-fix:
clk: ti: fix flag space conflict with clkctrl clocks
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
* clk-mvebu:
clk: mvebu: armada-38x: add support for missing clocks
clk: mvebu: cp110: Fix clock tree representation
* clk-phase:
clk: Don't show the incorrect clock phase
clk: update cached phase to respect the fact when setting phase
* clk-nxp:
clk: lpc32xx: Set name of regmap_config
* clk-mtk2712:
clk: mediatek: update clock driver of MT2712
dt-bindings: clock: add clocks for MT2712
* clk-qcom-rpmcc:
clk: qcom: rpmcc: Add support to XO buffered clocks
Document that Stratix10 clock bindings, and add the clock header file. The
clock header is an enumeration of all the different clocks on the Stratix10
platform.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.
-----BEGIN PGP SIGNATURE-----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=u8uZ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "arm64: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:
Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.
* tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable AHCI on Jetson TX1
arm64: tegra: Add SATA node for Tegra210
arm64: tegra: Add device tree for the Tegra194 P2972-0000 board
arm64: tegra: Add Tegra194 chip device tree
* Nuvoton NPCM7XX Clock Controller
Nuvoton Poleg BMC NPCM7XX contains an integrated clock controller, which
generates and supplies clocks to all modules within the BMC.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Allwinner H6 CCU has a "HDMI Slow Clock", which is currently missing
in the ccu-sun50i-h6 driver.
Add this missing clock to the driver.
Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
XO is onchip buffer clock to generate 19.2MHz.
This patch adds support to 5 XO buffer clocks found on PMIC8921,
these buffer clocks can be controlled from external pin or in
manual mode.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
add new clocks according to ECO design change
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
