elantech_init() calls elantech_set_absolute_mode which sets the driver in
an absolute mode. When after this the elantech_init fails, it is best to
turn the ps/2 mouse emulation mode back on by calling psmouse_reset() so
that it can work as a regular mouse.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we fail to match data returned by E7 and EC reports we state that we
found "Unknown ALPS touchpad" whereas it is most likely it is not ALPS
touchpad at all. Change wording a bit and reduce the message to debug so
that it does not litter users logs and confuse them.
Reported-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f8ec894945 allowed external callers
use slot dropping logic, unfortunately it also broke external users of
input_mt_is_used() as we stopped incrementing frame count unless input
device was set up to automatically drop unused slots.
Fixes: f8ec894945 ("Input: MT - make slot cleanup callable outside
mt_sync_frame()")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=83081
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the TI drv260x haptics/vibrator driver. This device uses the input
force feedback to produce a wave form to driver an ERM or LRA actuator
device.
The initial driver supports the devices real time playback mode. But the
device has additional wave patterns in ROM. This functionality will be
added in future patchsets.
Product data sheet is located here: http://www.ti.com/product/drv2605
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
kbd_res is used only when CONFIG_PCI is defined; condition its declaration as
well. This fixes the following compilation warning:
drivers/input/serio/i8042-sparcio.h:20:25: warning: ‘kbd_res’ defined but not used [-Wunused-variable]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Second round of updates for the input subsystem. Mostly small fixups
to the code merged in the first round (atmel_mxt_ts, wacom) but also a
smallish patch to xbox driver to support Xbox One controllers and a
patch to better handle Synaptics profile sensors found in Cr-48
Chromebooks that should not affect any other devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: edt-ft5x06 - remove superfluous assignment
Input: xpad - add support for Xbox One controllers
Input: atmel_mxt_ts - fix a few issues reported by Coverity
Input: atmel_mxt_ts - split config update a bit
Input: atmel_mxt_ts - simplify mxt_initialize a bit
Input: joystick - use get_cycles on ARMv8
Input: wacom - fix compiler warning if !CONFIG_PM
Input: cap1106 - allow changing key mapping from userspace
Input: synaptics - use firmware data for Cr-48
Input: synaptics - properly initialize slots for semi-MT
Input: MT - make slot cleanup callable outside mt_sync_frame()
Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AA
Somehow we ended up with a duplicate line in edt_ft5x06_register_write()
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers require an initialization message to start sending
data, so xpad_init_output becomes a required function. The Xbox One
controller does not have LEDs like the Xbox 360 controller, so that
functionality is not implemented. The format of messages controlling rumble
is currently undocumented, so rumble support is not yet implemented.
Note that Xbox One controller advertises three interfaces with the same
interface class, subclass and protocol, so we have to also match against
interface number.
Signed-off-by: Ted Mielczarek <ted@mielczarek.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This should fix the following issues reported by Coverity:
*** CID 1230625: Logically dead code (DEADCODE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1692 in mxt_initialize()
*** CID 1230627: Missing break in switch (MISSING_BREAK)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1436 in mxt_get_object_table()
*** CID 1230629: Out-of-bounds write (OVERRUN)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1267 in mxt_update_cfg()
*** CID 1230632: Unused pointer value (UNUSED_VALUE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1211 in mxt_update_cfg()
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's split config update code a bit so it is hopefully a bit easier to
read. Also, the firmware update callback should be the entity releasing
firmware blob, not lower layers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
I think having control flow with 2 goto/labels/flags is quite hard to read,
this version is a bit more readable IMO.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
As with ARM the ARMv8 architecture provides a cycle counter which can be
used to provide a high resolution time for the joystick driver and
silence the build warning that results from not having a precise timer
on ARMv8, making allmodconfig and allyesconfig quieter.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
Wire up support for EVIOC{G|S}KEYCODE to allow users change key mappings
from userspace.
Reviewed-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The profile sensor clickpad in a Cr-48 Chromebook does a reasonable job
of tracking individual fingers. This tracking isn't perfect, but,
experiments show that it works better than just passing "semi-mt" data
to userspace, and making userspace try to deduce where the fingers are
given a bounding box.
This patch tries to report correct two-finger positions instead of the
{(min_x, min_y), (max_x, max_y)} for profile sensor clickpads on Cr-48
chromebooks. Note that this device's firmware always reports the higher
(smaller y) finger in the "sgm" packet, and the lower (larger y) finger
in the "agm" packet. Thus, when a new finger arrives on the pad, the
kernel driver uses input core's contact tracking facilities to match
contacts with slots.
Inspired by patch by Daniel Kurtz <djkurtz@chromium.org> and Chung-yih
Wang <cywang@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Semi-MT devices are pointers too, so let's tell that to
input_mt_init_slots(), as well as let it set up the devices as semi-MT,
instead of us doing it manually.
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some semi-mt drivers use the slots in a manual way, but may still
want to call parts of the frame synchronization logic. This patch
makes input_mt_drop_unused callable from those drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
With this patch, we can press a key to wake up the VM after the VM executes
"echo freeze > /sys/power/state".
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull sparc updates from David Miller:
1) Add sparc RAM output to /proc/iomem, from Bob Picco.
2) Allow seeks on /dev/mdesc, from Khalid Aziz.
3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.
4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
not insert it into the TLB miss hash tables otherwise we'll
livelock. Based upon work by Christopher Alexander Tobias Schulze.
5) Fix BREAK detection in sunsab driver when no actual characters are
pending, from Christopher Alexander Tobias Schulze.
6) Because we have modules --> openfirmware --> vmalloc ordering of
virtual memory, the lazy VMAP TLB flusher can cons up an invocation
of flush_tlb_kernel_range() that covers the openfirmware address
range. Unfortunately this will flush out the firmware's locked TLB
mapping which causes all kinds of trouble. Just split up the flush
request if this happens, but in the long term the lazy VMAP flusher
should probably be made a little bit smarter.
Based upon work by Christopher Alexander Tobias Schulze.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
sparc64: Fix up merge thinko.
sparc: Add "install" target
arch/sparc/math-emu/math_32.c: drop stray break operator
sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
sparc64: Guard against flushing openfirmware mappings.
sunsab: Fix detection of BREAK on sunsab serial console
bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
sparc64: Do not insert non-valid PTEs into the TSB hash table.
sparc64: avoid code duplication in io_64.h
sparc64: reorder functions in io_64.h
sparc64: drop unused SLOW_DOWN_IO definitions
sparc64: remove macro indirection in io_64.h
sparc64: update IO access functions in PeeCeeI
sparcspkr: use sbus_*() primitives for IO
sparc: Add support for seek and shorter read to /dev/mdesc
sparc: use %s for unaligned panic
drivers/sbus/char: Micro-optimization in display7seg.c
display7seg: Introduce the use of the managed version of kzalloc
sparc64 - add mem to iomem resource
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
We can annotate the suspend/resume functions with '__maybe_unused' and get
rid of the ifdef, which makes the code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This switches the driver to using managed resources to simplify error
handling and to do away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for querying the physical size from the touchpad for Rushmore
and v7 touchpads, and use that to tell userspace the device resolution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We can annonate the suspend/resume functions with '__maybe_unused' and get
rid of the ifdef, which makes the code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When a kernel has CONFIG_PM=y and CONFIG_PM_SLEEP=n the following warnings are
seen:
drivers/input/touchscreen/mcs5000_ts.c:252:12: warning: 'mcs5000_ts_suspend' defined but not used [-Wunused-function]
static int mcs5000_ts_suspend(struct device *dev)
^
drivers/input/touchscreen/mcs5000_ts.c:262:12: warning: 'mcs5000_ts_resume' defined but not used [-Wunused-function]
static int mcs5000_ts_resume(struct device *dev)
Protect the suspend/resume functions with CONFIG_PM_SLEEP in order to fix these
build warnings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input device must be released(input_free_device) when ads7846_probe_dt
fails. This fixes the same by releasing resources on failure.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By writing zero to both the active and idle cycle times the maXTouch device
is put into a deep sleep mode when it consumes minimal power. It is
unnecessary to change the configuration of any other objects (for example
to disable T9 touchscreen).
It is counterproductive to reset the chip on resume, it will result in a
long delay. However it is necessary to issue a calibrate command after the
chip has spent any time in deep sleep.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide device tree support and binding information. Also provide support
for a new chip "pixcir_tangoc".
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of the Pixcir touch controller support up to 5 simultaneous
fingers and hardware tracking IDs. Prepare the driver for that.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using the Type-B Multi-Touch protocol.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Such as found on the new Toshiba Portégé Z30-A and Z40-A.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
[hdegoede@redhat.com: Remove softbutton handling, this is done in userspace]
[hdegoede@redhat.com: Report INPUT_PROP_BUTTONPAD]
[hdegoede@redhat.com: Do not report fake PRESSURE, reporting BTN_TOUCH is
enough]
[hdegoede@redhat.com: Various cleanups / refactoring]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So that decode functions can return a failure when appropriate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we detect more then 2 fingers report 2 touches, rather then only
reporting the upper left corner of the bounding box.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all the semi-mt specific handling shared between the v3 and v4
handling code to a common helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For v3 protocol devices, use the more accurate single touch data when the
mt data contains only one finger. Note the mt data reporting a finger count
of 1 should never happen, but better safe then sorry.
This brings the v3 bitmap handling in line with what the v4 code does,
allowing to factor out the common bits into a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When there are 2 fingers on the pad we don't know which one is which, so
use input_mt_assign_slots to make sure the right set of coordinates ends
up in the right slot.
Besides ensuring things end up in the right slot, this also results in a
nice cleanup, since sync_frame also handles non mt position and btn_touch
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for switching the DIY mt handling to using
input_mt_assign_slots && input_mt_sync_frame.
struct alps_fields is quite large, so while making changes to almost all uses
of it lets put it in our priv data instead of on the stack.
Having it in our priv data also allows using it directly for storing values
which need to be cached, rather then having separate x, y, z, fingers, etc.
copies in our priv data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes 2 fingers at the same height or width on the touchpad getting
reported at different y / x coordinates.
Note num_bits is always at least 1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alps_process_bitmap was resetting the point bit-count as soon as it saw
2 0 bits in a row. This means that unless the high point actually is at
the end of the bitmap, it would always get its num_bits set to 0.
Instead reset num_bits to 0 on a 0->1 transition, so that with > 2 fingers
we only count the number of bits occupied by the highest finger.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out the identical code for getting the bitmap points for x and y into
a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rushmore models don't have the Y-axis data in the bitmap inverted. Since
we now have 2 different Y orientations, make the Y bitmap data processing
use a forward loop like the X bitmap data processing, unifying the 2,
and invert the data later, except on Rushmore.
So far no-one has noticed this because the synaptics driver only uses the
non mt coordinates (except on clickpads, and there are no alps clickpads
using process_bitmap).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
V3 models only report mt bitmap data when there are 2 or more fingers on
the touchpad. So always generate 2 positions in alps_process_bitmap, and
for v3 models only fall back to st data when there was no mt data in a
mt packet (which should never happen).
This fixes 2 finger scrolling not working when using 2 fingers close to
each other.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom.ko is now a full HID driver, we have to move it into the proper
subdirectory: drivers/hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
No Functional changes, just some reordering.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
pktlen is now overwritten by the driver directly by reading the hid
report descriptor. There is no need to declare it statically.
We also move down the position of the field in the struct so that
we can keep the current declaration of Wacom devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This may infer a small difference with the previous implementation
due to the DIV_ROUND_CLOSEST() in the hid implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
HID already parses the report descriptor, so use it instead of implementing
our own. The special case for Bamboo PT 3rd gen is also removed and
handled in the same way Intuos 5 is treated, by hardcoding it in the
driver. Last, the unit_exponent stored into the hid field already is
signed, so there is no need to handle a two's complement anymore.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removes one more need of usb and intf.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the HID device as the parent for the power device when dealing with
a wireless receiver.
Removes one more usb dependency and does not break user space.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wacom tablets can share different physical sensors on one physical device.
These are called siblings in the code. The current way of implementation
relies on the USB topology to be able to share data amongs those sensors.
We can replace the code to match a HID subsystem, without involving the USB
topology:
- the first probed sensor does not find any siblings in the list
wacom_udev_list, so it creates its own wacom_hdev_data with its own
struct hid_device
- the other sensor checks the current list of siblings in wacom_hdev_data,
and if there is a match, it associates itself to the matched device.
To be sure that we are not associating different sensors from different
physical devices, we also check for the phys path of the hid device which
contains the USB topology.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Matches the current behavior of the HID subsystem and removes one more
dependency over USB.
The current user space clients which relies on this to fetch the
LEDs path need an update. However, we already break them in the
kernel v3.11 for the Bluetooth Wacom devices. They are going to be fixed
soon.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removes one more dependency over USB, but requires some changes in
the user space to find the sysfs files correctly.
This patch breaks the user space. However, the number of program
accessing the LEDs is quite limited and we can easily patch them
to handle the new HID behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This removes an USB dependency and is more accurate: the computed pktlen
is the actual maximum size of the reports forwarded by the device.
Given that the pktlen is correctly computed/validated, we can store it now
in the features struct instead of having a special handling in the rest of
the code.
Likewise, this information is not mandatory anymore in the description
of devices in wacom_wac.c. They will be removed in a separate patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
HID core already retrieves the report descritor. There is no need
to ask ourself for one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wacom.ko was a plain USB driver for a HID device. The communications
from/to the devices can actually be replaced with the HID API.
At the USB level, the reports are exactly the same.
This will allow to use uhid virtual devices instead of true USB devices.
This step is necessary to implement regression tests.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All USB Wacom tablets are actually HID devices.
For historical reasons, they are handled as plain USB devices.
The current code makes more and more reference to the HID subsystem
like implementing its own HID report descriptor parser to handle new
devices.
From the user point of view, we can transparently switch from this state
to a driver handled in the HID subsystem and clean up a lot of USB specific
code in the wacom.ko driver.
The other benefit once the USB dependecies have been removed is that we can
use a tool like uhid to make regression tests and allow further cleanup or
new implementations without risking breaking current behaviors.
To match the current handling of devices in wacom_wac.c, we rely on the
hid_type set by usbhid. usbhid sets the hid_type to HID_TYPE_USBMOUSE when
it sees a USB boot mouse protocol declared and HID_TYPE_USBNONE when the
device is plain HID. There is thus a one to one matching between the list
of supported devices before and after the switch from USB to HID.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current wacom code redefines constants that are already in linux/hid.h
This patch includes the official implementation and use it accross the code.
There is a conflict with HID_USAGE and others at the same level:
- in the wacom.ko implementation, those are the #define regarding the
value of the field in the report descriptor
- in the hid.h, those are bitmask
So add HDESC_ in their current definition.
Also, the struct hid_descriptor slightly differs from the linux/hid.h
point of view, so mark it as custom for this driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Wireless Receiver should also behave in the same way than regular
USB devices.
To simplify the unregistering of the different devices,
wacom_unregister_inputs() is introduced.
For consistency, the function wacom_register_input() is renamed into
wacom_register_inputs().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely removed from pad devices. If it is not
here, xf86-input-wacom correctly generates ones for its internal
use.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely removed from the pad device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We rely on the return code of wacom_bpt*() to do the input_sync().
wacom_wac_irq() then properly sync the input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely dropped for pad input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, the pad events are sent through the stylus input device
for the Intuos/Cintiqs, and through the touch input device for the
Bamboos.
To differentiate the buttons pressed on the pad from the ones pressed
on the stylus, the Intuos/Cintiq uses MISC_SERIAL and ABS_MISC. This
lead to a multiplexing of the events into one device, which are then
splitted out in xf86-input-wacom. Bamboos are not using MISC events
because the pad is attached to the touch interface, and only BTN_TOUCH
is used for the finger (and DOUBLE_TAP, etc...). However, the user space
driver still splits out the pad from the touch interface in the same
way it does for the pro line devices.
The other problem we can see with this fact is that some of the Intuos
and Cintiq have a wheel, and the effective range of the reported values
is [0..71]. Unfortunately, the airbrush stylus also sends wheel events
(there is a small wheel on it), but in the range [0..1023]. From the user
space point of view it is kind of difficult to understand that because
the wheel on the pad are quite common, while the airbrush tool is not.
A solution to fix all of these problems is to split out the pad device
from the stylus/touch. This decision makes more sense because the pad is
not linked to the absolute position of the finger or pen, and usually, the
events from the pad are filtered out by the compositor, which then convert
them into actions or keyboard shortcuts.
For backward compatibility with current xf86-input-wacom, the pad devices
still present the ABS_X, ABS_Y and ABS_MISC events, but they can be
completely ignored in the new implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This field was not used for 9 years, it is time to assign it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 1b2faaf7e2.
The Intuos4 series presents a bug in which it hangs if it receives
a set feature command while switching to the enhanced mode.
This bug is triggered when plugging an Intuos 4 while having
a gnome user session up and running.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom_wac.h will be moving to drivers/hid. Since we only need 3 definitions
from it let's simply copy them over.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wire up open/close so we do not try to send events until someone uses them;
this also allows us to remove micro_ts_remove() and rely fully on managed
resources.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the touchscreen connected to the Atmel
microcontroller on the iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written by Alessandro
GARDICH, with the bulk of the code for the new input architecture rewritten
by Dmitry Atamonow, and the final polish by Linus Walleij.
Signed-off-by: Alessandro GARDICH <gremlin@gremlin.it>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc6' into next
Merge with mainline to bring in changes to MFD to allow merging
ipaq-micro-ts driver.
maXTouch chips allow the reading of multiple messages in a single I2C
transaction, which reduces bus overhead and improves performance/latency. The
number of messages available to be read is given by the value in the T44
object which is located directly before the T5 object.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is in preparation for support of the T44 message count object.
Also, cache T5 address to avoid lookup on every interrupt cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By storing the previous T6 status byte multiple debug output of the same
status can be suppressed (for example CFGERR).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The T5 object may have various sizes depending on the objects used on the
particular maXTouch chip and firmware version, therefore it can't be
hardcoded in the driver. Allocate a buffer on probe instead.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MXT device may be in bootloader mode on probe, due to:
1) APP CRC failure, either:
a) flash corruption
b) bad power or other intermittent problem while checking CRC
2) If the device has been reset 10 or more times without accessing comms
3) Warm probe, device was in bootloader mode already
This code attempts to recover from 1(b) and 3.
There is an additional complexity: we have to try two possible bootloader
addresses because the mapping is not one-to-one and we don't know the exact
model yet.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Later chips (for example mXT1664S) different mappings for bootloader
addresses. This means that we must look at the family ID to determine
which address to use.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On a warm probe, the device might be in a state where an flash operation was
not completed.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the bootloader on the touchscreen controller fails to initialise the
firmware image, it stays in bootloader mode and reports a failure. It is
possible to reflash a working firmware image from this state.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By validating the checksum, we can identify if the configuration is
corrupt. In addition, this patch writes the configuration in a short
series of block writes rather than as many individual values.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The existing implementation which encodes the configuration as a binary
blob in platform data is unsatisfactory since it requires a kernel
recompile for the configuration to be changed, and it doesn't deal well
with firmware changes that move values around on the chip.
Atmel define an ASCII format for the configuration which can be exported
from their tools. This patch implements a parser for that format which
loads the configuration via the firmware loader and sends it to the MXT
chip.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touchpads are pointers, so make sure to pass the correct values to
input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't
work.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful to initialise the input device later:
- Screen parameters may not be not known yet, for instance if waiting for
firmware loader to return.
- Device may be in bootloader mode on probe (but could still be recovered by
firmware download).
In addition, later devices have a different touchscreen object (T100) which
requires handling differently.
This also reduces the complexity of the probe function.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The maXTouch chips use the CHG line to generate status events in bootloader
mode, and during configuration download, before there is enough information
to configure the input device. Therefore set up the interrupt handler
earlier.
However, this introduces states where parts of the interrupt processing
must not run. Use data->object_table as a way to tell whether the chip
information is valid, and data->input_dev as a way to tell whether it is
valid to generate input report.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the monotonic timestamp with ktime_mono_to_real() in
evdev_events().
In evdev_queue_syn_dropped() we can call either ktime_get() or
ktime_get_real() depending on the clkid. No point in having two calls
for CLOCK_REALTIME.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The memory are mapped using of_ioremap() which is
an indication this is sbus memory.
Shift all uses of inb/outb to the sbus variants.
The inb/outb methods uses ASI_PHYS_BYPASS_EC_E_L,
whereas sbus_ variants uses ASI_PHYS_BYPASS_EC_E.
The difference is if the reads/writes are done in
native or little endian.
But for byte reads/writes there is no difference
so this does not matter for inb/outb - and this
driver only uses the byte variants.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ioctl is the counterpart to EVIOCGVERSION and returns the
uinput-version the kernel was compiled with.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This moves basic checks and setup from uinput_setup_device() into
uinput_validate_absbits() to make it easier to use. This way, we can call
it from other places without copying the boilerplate code.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.
As this is not always the case, the regulator is requested as optional.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Recent version of xf86-input-wacom no longer support directly accessing
serial tablets. Instead xf86-input-wacom now expects all wacom tablets to
be driven by the kernel and to show up as evdev devices.
This has caused old serial Wacom tablets to stop working for people who still
have such tablets. Julian Squires has written a serio input driver to fix this:
https://github.com/tokenrove/wacom-serial-iv
This is a cleaned up version of this driver with improved Graphire support
(I own an old Graphire myself).
Signed-off-by: Julian Squires <julian@cipht.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We attempt to remove noise from coordinates reported by devices in
input_handle_abs_event(), unfortunately, unless we were dropping the
event altogether, we were ignoring the adjusted value and were passing
on the original value instead.
Cc: stable@vger.kernel.org
Reviewed-by: Andrew de los Reyes <adlr@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch introduces the use of managed interfaces like devm_kzalloc,
devm_input_allocate_device, devm_request_threaded_irq etc. and does away
with the calls to free the allocated memory. The remove function is no
longer required and is completely done away with. Also, the labels in the
probe function are removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel
capacitive touch sensor.
For now, only the capacitive buttons are supported, and no specific
settings that can be tweaked for individual channels, except for the
device-wide sensitivity gain. The defaults seem to work just fine out of
the box, so I'll leave configurable parameters for someone who's in need
of them and who can actually measure the impact. All registers are
prepared, however. Many of them are just not used for now.
The implementation does not make any attempt to be compatible to platform
data driven boards, but fully depends on CONFIG_OF.
Power management functions are also left for volounteers with the ability
to actually test them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add #ifdef CONFIG_PM_SLEEP around keyscan_supend() and keyscan_resume() to
fix the following compiler warnings occuring if CONFIG_PM_SLEEP is unset:
+ /scratch/kisskb/src/drivers/input/keyboard/st-keyscan.c: warning: 'keyscan_resume' defined but not used [-Wunused-function]: => 235:12
+ /scratch/kisskb/src/drivers/input/keyboard/st-keyscan.c: warning: 'keyscan_suspend' defined but not used [-Wunused-function]: => 218:12
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lkml.org/lkml/2014/7/8/109
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acer Aspire needs to be added to nomux blacklist, otherwise the touchpad
misbehaves rather randomly.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we receive EC interrupts after the cros_ec driver has probed, but
before the cros_ec_keyb driver has probed, the cros_ec IRQ handler
will not run the cros_ec_keyb notifier and the EC will leave the IRQ
line asserted. The cros_ec IRQ handler then returns IRQ_HANDLED and
the resulting flood of interrupts causes the machine to hang.
Since the EC interrupt is currently only used for the keyboard, move
the setup and handling of the EC interrupt to the cros_ec_keyb driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the three wrapper functions that talk to the EC without passing all
the desired arguments and just use the underlying communication function
that passes everything in a struct intead.
This is internal code refactoring only. Nothing should change.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the attribute groups of the led-class to create the time attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In the hopes that people run new kernels on their devices, let's add a
warning message asking users to have their DTS file fixed.
The goal is that by Linux 4.0 we will be able to remove support for the
bogus version of our touchscreen's DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Historically we dealt with touch_max equals to 2 differently from
other MT devices. Now we use input_mt_*() to process all MT events,
as long as touch_max is greater than 1. So, there is no need to
take (touch_max == 2) as a special case any more.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A big update to the Atmel touchscreen driver, devm support for polled
input devices, several drivers have been converted to using managed
resources, and assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: synaptics - fix resolution for manually provided min/max
Input: atmel_mxt_ts - fix invalid return from mxt_get_bootloader_version
Input: max8997_haptic - add error handling for regulator and pwm
Input: elantech - don't set bit 1 of reg_10 when the no_hw_res quirk is set
Input: elantech - deal with clickpads reporting right button events
Input: edt-ft5x06 - fix an i2c write for M09 support
Input: omap-keypad - remove platform data support
ARM: OMAP2+: remove unused omap4-keypad file and code
Input: ab8500-ponkey - switch to using managed resources
Input: max8925_onkey - switch to using managed resources
Input: 88pm860x-ts - switch to using managed resources
Input: 88pm860x_onkey - switch to using managed resources
Input: intel-mid-touch - switch to using managed resources
Input: wacom - process outbound for newer Cintiqs
Input: wacom - set stylus_in_proximity when pen is in range
DTS: ARM: OMAP3-N900: Add tsc2005 support
Input: tsc2005 - add DT support
Input: add common DT binding for touchscreens
Input: jornada680_kbd - switch top using managed resources
Input: adp5520-keys - switch to using managed resources
...
commit 421e08c41f fixed the reported min/max for the X and Y axis,
but unfortunately, it broke the resolution of those same axis.
On the t540p, the resolution is the same regarding X and Y. It is not
a problem for xf86-input-synaptics because this driver is only interested
in the ratio between X and Y.
Unfortunately, xf86-input-cmt uses directly the resolution, and having a
null resolution leads to some divide by 0 errors, which are translated by
-infinity in the resulting coordinates.
Reported-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's start checking return value of regulator_enable and pwm_enable to
avoid errors. Fixes the following warning:
drivers/input/misc/max8997_haptic.c:185:19: warning: ignoring return value of ‘regulator_enable’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver sends 3 bytes instead of 2 when accessing a register on the M09
firmware, so writing to gain seems to overflow into the offset register.
Signed-off-by: Robert Woerle <robert@linuxdevelopment.de>
Acked-By: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Pull input subsystem fixes from Dmitry Torokhov:
"A couple of driver/build fixups and also redone quirk for Synaptics
touchpads on Lenovo boxes (now using PNP IDs instead of DMI data to
limit number of quirks)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - change min/max quirk table to pnp-id matching
Input: synaptics - add a matches_pnp_id helper function
Input: synaptics - T540p - unify with other LEN0034 models
Input: synaptics - add min/max quirk for the ThinkPad W540
Input: ambakmi - request a shared interrupt for AMBA KMI devices
Input: pxa27x-keypad - fix generating scancode
Input: atmel-wm97xx - only build for AVR32
Input: fix ps2/serio module dependency
This is unused since all users (OMAP4/5) are DT only.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.
The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify error
handling and allows us to get rid of da9034_touch_remove().
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix a typo error in MELFAS MCS-5000 controller driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix a typo error in mms114 touchscreen driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix a typo error in MELFAS 5000/5080 controller driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By reading the touchscreen configuration from the settings that the
maXTouch chip is actually using, we can remove some platform data.
The matrix size is not used for anything, and results in some rather
confusing code to re-read it because it may change when configuration
is downloaded, so don't print it out.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for simplifying the min/max quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.
This is a preparation patch for simplifying the quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Atmel supplies firmware files in ASCII HEX format (.enc) which must be
converted before they can be loaded by kernel driver. Try to detect
the error and print a friendly error message rather than feeding junk
to the bootloader.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By implementing a frame counter, print out fewer debug messages (the
firmware may contain hundreds of frames).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move bootloaders reads/writes into separate functions. Instead of switching
client->addr, define new field bootloader_addr in mxt_data. Implement
lookup calculation for bootloader addresses.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The configuration is stored in NVRAM on the maXTouch chip. When the device
is reset it reports a CRC of the stored configuration values. Therefore it
isn't necessary to send the configuration on each probe - we can check the
CRC matches and avoid a timeconsuming backup/reset cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The delay before the chip can be accessed after reset varies between
different chips in maXTouch family. Waiting for an interrupt and a T6
status message with the RESET bit set is a better behaviour.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rather than msleep for MXT_RESET_TIME and MXT_FWRESET_TIME during the
transition to bootloader mode and the transition back from app, wait for
the CHG assert to indicate that the transition is done.
This change replaces the msleep with a wait for completion that the
mxt_interrupt handler signals.
Also add CHG poll after last firmware frame - some bootloader versions will
assert the interrupt line after the final frame, in testing this meant that
the driver attempts to read the info block too early whilst the chip is
still resetting.
This improves firmware update time as we no longer wait longer than
necessary for each reset.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver should not immediately read bootloader status when in
Application Update Mode. The CHG line will assert when the device has made
a state transition and is ready to report a new status via i2c.
This change adds a wait for completion in mxt_check_bootloader, and changes
the mxt_interrupt handler to signal the completion.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These two object table entry fields are reported 1 less than their value.
When used, however, we always want the actual size and instances.
To keep the object size and instances 1-byte fields, and thus preserve
the object-table struct's 6-byte packed alignment, add some convenient
accessor functions that do the +1 every time these fields are accessed.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* The mapping of the GPIO numbers into the T19 status byte varies between
different maXTouch chips. Some have up to 7 GPIOs. Allowing a keycode array
of up to 8 items is simpler and more generic. So replace #define with
configurable number of keys which also allows the removal of is_tp.
* Rename platform data parameters to include "t19" to prevent confusion with
T15 key array.
* Probe aborts early on when pdata is NULL, so no need to check.
* Move "int i" to beginning of function (mixed declarations and code)
* Use API calls rather than __set_bit()
* Remove unused dev variable.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is not necessary to download these values to the maXTouch chip on every
probe, since they are stored in NVRAM. It makes life difficult when tuning
the device to keep them in sync with the config array/file, and requires a
new kernel build for minor tweaks.
These parameters only represent a tiny subset of the available
configuration options, tracking all of these options in platform data would
be a endless task. In addition, different versions of maXTouch chips may
have these values in different places or may not even have them at all.
Having these values also makes life more complex for device tree and other
platforms where having to define a static configuration isn't helpful.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve the suspend and resume handlers to allow the device
to wakeup the system from suspend.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the attb_read_val() platform hook. Instead, read the ATTB gpio
directly from the driver.
Fail if valid ATTB gpio is not provided by patform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce helper functions to configure power and interrupt registers.
Default to IDLE mode on probe as device supports auto wakeup to ACVIE mode
on detecting finger touch.
Configure interrupt mode and polarity on start up. Power down on device
closure or module removal.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_() and friends for allocating memory, input device
and IRQ.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In case allocation via usb_alloc_coherent() fails in ims_pcu_buffers_alloc(),
the function jumps to the exit path without initializing local variable
'error' that is used as return value. Detected by Coverity - CID 1016531.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the 0x4004, 0x5000, and 0x5002 sensors found
on what should be the Motion R12, Fujitsu Q704, and Fujitsu T904. These
tablets use a new report ID (3) for their touch packets and a slightly
different HID descriptor format, but are otherwise largely identical in
protocol to the "MTTPC" tablets.
Note:
* The R12 uses its 0x4004 sensor for touch input only. A pen interface
is not present in its HID descriptor, though its possible a 0x4004
may be used for pen input by other tablet PCs in the future.
* The 0x5002 sensor appears to use a new report ID (8) for its pen
packets. The other sensors continue to use the traditional report
ID (2).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A few cases of incorrectly using 'le16_to_cpup' instead of
'get_unaligned_le16' have been noticed and fixed.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTbTZoAAoJEHm+PkMAQRiGLssH/3Rv6e9rAkEw9Ey0ymwGsCvf
6DEAcSgaWEyYWEU+DmkEQ3hbiOyESHFOsWE4zA2F5WY0w2Xsr+wDCS+14WCN6NHT
6sxSYGj1hd+ni6GhlGxfRpUXtY59h7TKHaaHYKPIOsO4OWXVeD53trpq416kvqal
zWkFOWeiEyeJnNKv0z0+5QWTeFDjTd1YawWcK/8kFez1Y4BXBECTgKoJaEcvowfU
j7oQ0BJxtLlxFgCB84bZTUbGuyn1x9FiS7Z2w9JcqSkTLMabFjsbA15eZIV66N4s
boaxlRvyvelR09eiiYYqOLxUmeEi1wRqtAM3yln1Y5/MX+DAmf5/sylqKtC5eLg=
=ezkr
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc5' into next
Merge with Linux 3.15-rc5 to sync up Wacom and other changes.
If the debounce time is 0 our usage of ilog2() later on in this driver will
cause undefined behavior. If CONFIG_OF=n this fact is evident to the
compiler, and it emits a call to ____ilog2_NaN() which doesn't exist. Fix
this by setting a sane default for debounce and failing to probe if
debounce is 0 in the DT.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Win8 version of the Panasonic CF-H2 includes a new Wacom device.
The pen interface appears to use the same protocol as before, but the
touch interface has been tweaked to send Win8-compatible reports.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sun4i resisitive touchscreen controller also comes with a built-in
temperature sensor. This commit adds support for it.
This commit also introduces a new "ts-attached" device-tree property,
when this is not set, the input part of the driver won't register. This way
the internal temperature sensor can be used to measure the SoC temperature
independent of there actually being a touchscreen attached to the controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Note the sun4i-ts controller is capable of detecting a second touch, but
when a second touch is present then the accuracy becomes so bad the
reported touch location is not useable.
The original android driver contains some complicated heuristics using the
aprox. distance between the 2 touches to see if the user is making a pinch
open / close movement, and then reports emulated multi-touch events around
the last touch coordinate (as the dual-touch coordinates are worthless).
These kinds of heuristics are just asking for trouble (and don't belong in
the kernel). So this driver offers straight forward, reliable single touch
functionality only.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Managed resources are becoming more and more popular in drivers. Let's
implement managed polled input devices, to complement managed regular input
devices.
Similarly to managed regular input devices only one new call
devm_input_allocate_polled_device() is added and the rest of APIs is
modified to work with both managed and non-managed devices.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Polled device's attributes controlling polling rate and whether polling is
enabled are attached to input device. We should have device core
instantiate them for us, so that they are created by the time new device
notification is sent to userspace, instead of doing it ourselves
afterwards.
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace existing gpio resource handling in the driver with managed
resources, this ensures more consistent error values and simplifies error
paths.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch simplifies GPIO handling in the driver by using GPIO functions
based on descriptors. As a result this driver now can be used for boards
without DT support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the driver by using managed resources for memory allocation of
internal structure, input device allocation and irq request.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change some dev_dbg() invocations to dev_err() ones, because they
are supposed to output error messages.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
