Once the IDX connection is down, there's no point in trying to issue
more IOs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This let's us start every new IDX connection with clean seqnos.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like these were never used, ever since the driver was initially
added.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's good practice to not blindly trust what the HW offers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly define the cmd's struct to get rid of some casts and accesses
at magic offsets.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
card->info.unique_id is always 0 for IQD devices, so don't bother with
copying it into the 0-initialized cmd.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull HID subsystem fixes from Jiri Kosina:
- syzkaller-reported error handling fixes in various drivers, from
various people
- increase of HID report buffer size to 8K, which is apparently needed
by certain modern devices
- a few new device-ID-specific fixes / quirks
- battery charging status reporting fix in logitech-hidpp, from Filipe
Laíns
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: hid-bigbenff: fix race condition for scheduled work during removal
HID: hid-bigbenff: call hid_hw_stop() in case of error
HID: hid-bigbenff: fix general protection fault caused by double kfree
HID: i2c-hid: add Trekstor Surfbook E11B to descriptor override
HID: alps: Fix an error handling path in 'alps_input_configured()'
HID: hiddev: Fix race in in hiddev_disconnect()
HID: core: increase HID report buffer size to 8KiB
HID: core: fix off-by-one memset in hid_report_raw_event()
HID: apple: Add support for recent firmware on Magic Keyboards
HID: ite: Only bind to keyboard USB interface on Acer SW5-012 keyboard dock
HID: logitech-hidpp: BatteryVoltage: only read chargeStatus if extPower is active
Follow the pattern used with other *_show_fdinfo functions and only
define unix_show_fdinfo and set it in proto_ops if CONFIG_PROCFS
is set.
Fixes: 3c32da19a8 ("unix: Show number of pending scm files of receive queue in fdinfo")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
selftests: updates for mlxsw driver test
This patchset contains tweaks to the existing tests and is also adding
couple of new ones, namely tests for shared buffer and red offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale test for Spectrum-2 should be invoked for Spectrum-2 and
Spectrum-3. Add the appropriate device ID.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the test inserts X /32 routes and for each route it is
testing that a packet sent from the first host is received by the second
host, which is very time-consuming.
Instead only validate the offload flag of each route and get the same result.
Wait between the creation of the routes and the offload validation in
order to make sure that all the routes were successfully offloaded.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding a given number of flower rules for different IPv6
addresses, the test generates traffic and ensures that each packet is
received, which is time-consuming.
Instead, test the offload indication of the tc flower rules and reduce
the running time by half.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test the max shared buffer occupancy for port's pool and port's TC's (using
different types of packets).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlxsw lib for common defines, helpers etc.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two devlink port helpers:
* devlink port get by netdev
* devlink cpu port get
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sanity check for devlink info command.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test physical ports' shared buffer configuration options using random
values related to a specific configuration option. There are 3
configuration options: pool, TC bind and portpool.
Each sub-test, test a different configuration option and random the related
values as the follow:
* For pools, pool's size will be randomized.
* For TC bind, pool number and threshold will be randomized.
* For portpools, threshold will be randomized.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rtnetlink test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blackhole routes test uses offload indication checks.
Use busywait helper and wait until the routes offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test checks that packets are trapped when they should egress a
router interface (RIF) that has become disabled. This is a temporary
state in a RIF's deletion sequence.
Currently, the test deletes the RIF by flushing all the IP addresses
configured on the associated netdev (br0). However, this is racy, as
this also flushes all the routes pointing to the netdev and if the
routes are deleted from the device before the RIF is disabled, then no
packets will try to egress the disabled RIF and the trap will not be
triggered.
Instead, trigger the deletion of the RIF by unlinking the mlxsw port
from the bridge that is backing the RIF. Unlike before, this will not
cause the kernel to delete the routes pointing to the bridge.
Note that due to current mlxsw locking scheme the RIF is always deleted
first, but this is going to change.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have multiple mirror actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have redirect rule on egress-bound block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests that below the queue minimum length, there is no dropping /
marking, and above max, everything is dropped / marked.
The test is structured as a core file with topology and test code, and
three wrappers: one for RED used as a root Qdisc, and two for
testing (W)RED under PRIO and ETS.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract a helper __start_traffic() configurable by protocol type. Allow
passing through extra mausezahn arguments. Add a wrapper,
start_tcp_traffic().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo bin says:
====================
hinic: BugFixes
the bug fixed in patch #2 has been present since the first commit.
the bugs fixed in patch #1 and patch #3 have been present since the
following commits:
patch #1: 352f58b0d9 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
patch #3: 421e952628 ("hinic: add rss support")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
should use real receive queue number to configure hw rss
indirect table rather than maximal queue number
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a reserved field is used to signify prime physical function index
in the latest firmware version, so we must assign a value to it
correctly
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
can not use a local variable as an input parameter of
irq_set_affinity_hint
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl5U9RsACgkQF0NaE2wM
fljetAgAkIzf4eaENcrU8LUOjR7p66a6IIBLA5WAlSc2CvmfHrI6fJgxUWHZKxZp
0NhzoNiYo0zPkrPpjabpWLwyiIAIDR3RA7B+dOuxCW0AieLuPV6ltg3ytXukeGvo
ZOVXEVgorG6Kx4oNvCKqrUVPICU+SErSRmREVggLWi4iM1cQzUxcMIBJEw8SgHEV
mDT5igcfSqWWxU8rF6zGY0zV+l+pN12gf7EfmKnJ6E0oCWNZ6VHbmyHaVxIS76C7
9aiNW5+ATeCPEYvXseAaOSCbJWOU0wlxrskpHSN2yBgGHTGipEEFZF5rAj8QbeYH
9UPqvmgKFLZqQ3aCqAK3jltm8ojyRA==
=rH5d
-----END PGP SIGNATURE-----
Merge tag 'docs-5.6-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A pair of docs-build fixes"
* tag 'docs-5.6-fixes' of git://git.lwn.net/linux:
docs: Fix empty parallelism argument
docs: remove MPX from the x86 toc
-----BEGIN PGP SIGNATURE-----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=DyVs
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20200226' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two fixes for problems found by syzbot:
- Moving audit filter structure fields into a union caused some
problems in the code which populates that filter structure.
We keep the union (that idea is a good one), but we are fixing the
code so that it doesn't needlessly set fields in the union and mess
up the error handling.
- The audit_receive_msg() function wasn't validating user input as
well as it should in all cases, we add the necessary checks"
* tag 'audit-pr-20200226' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: always check the netlink payload length in audit_receive_msg()
audit: fix error handling in audit_data_to_entry()
Russell King says:
====================
VLANs, DSA switches and multiple bridges
This is a repost of the previously posted RFC back in December, which
did not get fully reviewed. I've dropped the RFC tag this time as no
one really found anything too problematical in the RFC posting.
I've been trying to configure DSA for VLANs and not having much success.
The setup is quite simple:
- The main network is untagged
- The wifi network is a vlan tagged with id $VN running over the main
network.
I have an Armada 388 Clearfog with a PCIe wifi card which I'm trying to
setup to provide wifi access to the vlan $VN network, while the switch
is also part of the main network.
However, I'm encountering problems:
1) vlan support in DSA has a different behaviour from the Linux
software bridge implementation.
# bridge vlan
port vlan ids
lan1 1 PVID Egress Untagged
...
shows the default setup - the bridge ports are all configured for
vlan 1, untagged egress, and vlan 1 as the port vid. Issuing:
# ip li set dev br0 type bridge vlan_filtering 1
with no other vlan configuration commands on a Linux software bridge
continues to allow untagged traffic to flow across the bridge.
This difference in behaviour is because the MV88E6xxx VTU is
completely empty - because net/dsa ignores all vlan settings for
a port if br_vlan_enabled(dp->bridge_dev) is false - this reflects
the vlan filtering state of the bridge, not whether the bridge is
vlan aware.
What this means is that attempting to configure the bridge port
vlans before enabling vlan filtering works for Linux software
bridges, but fails for DSA bridges.
2) Assuming the above is sorted, we move on to the next issue, which
is altogether more weird. Let's take a setup where we have a
DSA bridge with lan1..6 in a bridge device, br0, with vlan
filtering enabled. lan1 is the upstream port, lan2 is a downstream
port that also wants to see traffic on vlan id $VN.
Both lan1 and lan2 are configured for that:
# bridge vlan add vid $VN dev lan1
# bridge vlan add vid $VN dev lan2
# ip li set br0 type bridge vlan_filtering 1
Untagged traffic can now pass between all the six lan ports, and
vlan $VN between lan1 and lan2 only. The MV88E6xxx 8021q_mode
debugfs file shows all lan ports are in mode "secure" - this is
important! /sys/class/net/br0/bridge/vlan_filtering contains 1.
tcpdumping from another machine on lan4 shows that no $VN traffic
reaches it. Everything seems to be working correctly...
In order to further bridge vlan $VN traffic to hostapd's wifi
interface, things get a little more complex - we can't add hostapd's
wifi interface to br0 directly, because hostapd will bring up the
wifi interface and leak the main, untagged traffic onto the wifi.
(hostapd does have vlan support, but only as a dynamic per-client
thing, and there's no hooks I can see to allow script-based config
of the network setup before hostapd up's the wifi interface.)
So, what I tried was:
# ip li add link br0 name br0.$VN type vlan id $VN
# bridge vlan add vid $VN dev br0 self
# ip li set dev br0.$VN up
So far so good, we get a vlan interface on top of the bridge, and
tcpdumping it shows we get traffic. The 8021q_mode file has not
changed state. Everything still seems to be correct.
# bridge addbr br1
Still nothing has changed.
# bridge addif br1 br0.$VN
And now the 8021q_mode debugfs file shows that all ports are now in
"disabled" mode, but /sys/class/net/br0/bridge/vlan_filtering still
contains '1'. In other words, br0 still thinks vlan filtering is
enabled, but the hardware has had vlan filtering disabled.
Adding some stack traces to an appropriate point indicates that this
is because __switchdev_handle_port_attr_set() recurses down through
the tree of interfaces, skipping over the vlan interface, applying
br1's configuration to br0's ports.
This surely can not be right - surely
__switchdev_handle_port_attr_set() and similar should stop recursing
down through another master bridge device? There are probably other
network device classes that switchdev shouldn't recurse down too.
I've considered whether switchdev is the right level to do it, and
I think it is - as we want the check/set callbacks to be called for
the top level device even if it is a master bridge device, but we
don't want to recurse through a lower master bridge device.
v2: dropped patch 3, since that has an outstanding issue, and my
question on it has not been answered. Otherwise, these are the
same patches. Maybe we can move forward with just these two?
v3: include DSA ports in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting VLANs on DSA switches, the VLAN is added to both the port
concerned as well as the CPU port by dsa_slave_vlan_add(), as well as
any DSA ports. If multiple ports are configured with the same VLAN ID,
this triggers a warning on the CPU and DSA ports.
Avoid this warning for CPU and DSA ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring a tree of independent bridges, propagating changes
from the upper bridge across a bridge master to the lower bridge
ports brings surprises.
For example, a lower bridge may have vlan filtering enabled. It
may have a vlan interface attached to the bridge master, which may
then be incorporated into another bridge. As soon as the lower
bridge vlan interface is attached to the upper bridge, the lower
bridge has vlan filtering disabled.
This occurs because switchdev recursively applies its changes to
all lower devices no matter what.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In smc_ib_remove_dev() check if the provided ib device was actually
initialized for SMC before.
Reported-by: syzbot+84484ccebdd4e5451d91@syzkaller.appspotmail.com
Fixes: a4cf0443c4 ("smc: introduce SMC as an IB-client")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.
Fixes: 481a7d154c ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware paths for the VSC8584 PHYs not not contain the leading
'microchip/' directory, as used in linux-firmware, resulting in an
error when probing the driver. This patch fixes it.
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callers only expect NULL pointers, so returning an error pointer
will lead to an Oops.
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a missing shift for the media operation mode selection.
This does not fix the driver as the current operation mode (copper) has
a value of 0, but this wouldn't work for other modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit we revert the part of
commit 1a63443afd ("net/amazon: Ensure that driver version is aligned to the linux kernel"),
which breaks the interface between the ENA driver and FW.
We also replace the use of DRIVER_VERSION with DRIVER_GENERATION
when we bring back the deleted constants that are used in interface with
ENA device FW.
This commit does not change the driver version reported to the user via
ethtool, which remains the kernel version.
Fixes: 1a63443afd ("net/amazon: Ensure that driver version is aligned to the linux kernel")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
mptcp: update mptcp ack sequence outside of recv path
This series moves mptcp-level ack sequence update outside of the recvmsg path.
Current approach has two problems:
1. There is delay between arrival of new data and the time we can ack
this data.
2. If userspace doesn't call recv for some time, mptcp ack_seq is not
updated at all, even if this data is queued in the subflow socket
receive queue.
Move skbs from the subflow socket receive queue to the mptcp-level
receive queue, updating the mptcp-level ack sequence and have recv
take skbs from the mptcp-level receive queue.
The first place where we will attempt to update the mptcp level acks
is from the subflows' data_ready callback, even before we make userspace
aware of new data.
Because of possible deadlock (we need to take the mptcp socket lock
while already holding the subflow sockets lock), we may still need to
defer the mptcp-level ack update. In such case, this work will be either
done from work queue or recv path, depending on which runs sooner.
In order to avoid pointless scheduling of the work queue, work
will be queued from the mptcp sockets lock release callback.
This allows to detect when the socket owner did drain the subflow
socket receive queue.
Please see individual patches for more information.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't schedule the work queue right away, instead defer this
to the lock release callback.
This has the advantage that it will give recv path a chance to
complete -- this might have moved all pending packets from the
subflow to the mptcp receive queue, which allows to avoid the
schedule_work().
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't lock_sock() the mptcp socket from the subflow data_ready callback,
it would result in ABBA deadlock with the subflow socket lock.
We can however grab the spinlock: if that succeeds and the mptcp socket
is not owned at the moment, we can process the new skbs right away
without deferring this to the work queue.
This avoids the schedule_work and hence the small delay until the
work item is processed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only used to discard stale data from the subflow, so move
it where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If userspace never drains the receive buffers we must stop draining
the subflow socket(s) at some point.
This adds the needed rmem accouting for this.
If the threshold is reached, we stop draining the subflows.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If userspace is not reading data, all the mptcp-level acks contain the
ack_seq from the last time userspace read data rather than the most
recent in-sequence value.
This causes pointless retransmissions for data that is already queued.
The reason for this is that all the mptcp protocol level processing
happens at mptcp_recv time.
This adds work queue to move skbs from the subflow sockets receive
queue on the mptcp socket receive queue (which was not used so far).
This allows us to announce the correct mptcp ack sequence in a timely
fashion, even when the application does not call recv() on the mptcp socket
for some time.
We still wake userspace tasks waiting for POLLIN immediately:
If the mptcp level receive queue is empty (because the work queue is
still pending) it can be filled from in-sequence subflow sockets at
recv time without a need to wait for the worker.
The skb_orphan when moving skbs from subflow to mptcp level is needed,
because the destructor (sock_rfree) relies on skb->sk (ssk!) lock
being taken.
A followup patch will add needed rmem accouting for the moved skbs.
Other problem: In case application behaves as expected, and calls
recv() as soon as mptcp socket becomes readable, the work queue will
only waste cpu cycles. This will also be addressed in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be extended with functionality in followup patches.
Initial user is moving skbs from subflows receive queue to
the mptcp-level receive queue.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
allows us to schedule the work queue to drain the ssk receive queue in
a followup patch.
This is needed to avoid sending all-to-pessimistic mptcp-level
acknowledgements. At this time, the ack_seq is what was last read by
userspace instead of the highest in-sequence number queued for reading.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Small driver update
This patchset contains couple of patches not related to each other. They
are small optimization and extension changes to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
