When processing a duplicate cookie-echo chunk, for case 'A' and 'B',
after sctp_process_init for the new asoc, if auth is enabled for the
cookie-ack chunk, the active key should also be initialized.
Otherwise, the cookie-ack chunk made later can not be set with auth
shkey properly, and a crash can even be caused by this, as after
Commit 1b1e0bc994 ("sctp: add refcnt support for sh_key"), sctp
needs to hold the shkey when making control chunks.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the bbr->idle_restart tracking was zeroing out the
bbr->idle_restart bit upon ACKs that did not SACK or ACK anything,
e.g. receiving incoming data or receiver window updates. In such
situations BBR would forget that this was a restart-from-idle
situation, and if the min_rtt had expired it would unnecessarily enter
PROBE_RTT (even though we were actually restarting from idle but had
merely forgotten that fact).
The fix is simple: we need to remember we are restarting from idle
until we receive a S/ACK for some data (a S/ACK for the first flight
of data we send as we are restarting).
This commit is a stable candidate for kernels back as far as 4.9.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
- connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
- connect port 2 (eth1) to linux Host 1 with vlan 1 configured
- ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.
Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.
To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 93c0d549c4c5a7382ad70de6b86610b7aae57406.
Unfortunately the padding will break 32 bit userspace.
Ouch. Need to add some compat code, revert for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware requires that the ttl value for an encapsulating ipv4 tunnel
header be included as an action field. Prior to the support of Geneve
tunnel encap (when ttl set was removed completely), ttl value was
extracted from the tunnel key. However, tests have shown that this can
still produce a ttl of 0.
Fix the issue by setting the namespace default value for each new tunnel.
Follow up patch for net-next will do a full route lookup.
Fixes: 3ca3059dc3 ("nfp: flower: compile Geneve encap actions")
Fixes: b27d6a95a7 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is reported that in some cases, write_space may be called in
do_tcp_sendpages, such that we recursively invoke do_tcp_sendpages again:
[ 660.468802] ? do_tcp_sendpages+0x8d/0x580
[ 660.468826] ? tls_push_sg+0x74/0x130 [tls]
[ 660.468852] ? tls_push_record+0x24a/0x390 [tls]
[ 660.468880] ? tls_write_space+0x6a/0x80 [tls]
...
tls_push_sg already does a loop over all sending sg's, so ignore
any tls_write_space notifications until we are done sending.
We then have to call the previous write_space to wake up
poll() waiters after we are done with the send loop.
Reported-by: Andre Tomt <andre@tomt.net>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is valid to have static routes where the nexthop
is an interface not an address such as tunnels.
For IPv4 it was possible to use ECMP on these routes
but not for IPv6.
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Cc: David Ahern <dsahern@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_get_rxnfc(), the object "info" is firstly copied from
user-space. If the FLOW_RSS flag is set in the member field flow_type of
"info" (and cmd is ETHTOOL_GRXFH), info needs to be copied again from
user-space because FLOW_RSS is newer and has new definition, as mentioned
in the comment. However, given that the user data resides in user-space, a
malicious user can race to change the data after the first copy. By doing
so, the user can inject inconsistent data. For example, in the second
copy, the FLOW_RSS flag could be cleared in the field flow_type of "info".
In the following execution, "info" will be used in the function
ops->get_rxnfc(). Such inconsistent data can potentially lead to unexpected
information leakage since ops->get_rxnfc() will prepare various types of
data according to flow_type, and the prepared data will be eventually
copied to user-space. This inconsistent data may also cause undefined
behaviors based on how ops->get_rxnfc() is implemented.
This patch simply re-verifies the flow_type field of "info" after the
second copy. If the value is not as expected, an error code will be
returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in mlx4_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a 32 bit hole just after type. It's best to
give it a name, this way compiler is forced to initialize
it with rest of the structure.
Reported-by: Kevin Easton <kevin@guarana.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in tx_fw_stat_gstrings text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in netdev_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set a bond slave's master to bridge via ioctl, we only check
the IFF_BRIDGE_PORT flag. Although we will find the slave's real master
at netdev_master_upper_dev_link() later, it already does some settings
and allocates some resources. It would be better to return as early
as possible.
v1 -> v2:
use netdev_master_upper_dev_get() instead of netdev_has_any_upper_dev()
to check if we have a master, because not all upper devs are masters,
e.g. vlan device.
Reported-by: syzbot+de73361ee4971b6e6f75@syzkaller.appspotmail.com
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: more ARFS fixes
A couple more bits of breakage in my recent ARFS and async filters work.
Patch #1 in particular fixes a bug that leads to memory trampling and
consequent crashes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Owing to a missing conditional, the result of rps_may_expire_flow() was
being ignored and filters were being removed even if we'd decided not to
expire them.
Fixes: f8d6203780 ("sfc: ARFS filter IDs")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx->type->filter_insert() returns an ID rather than the index that
efx->type->filter_async_insert() used to, which causes it to exceed
efx->type->max_rx_ip_filters on some EF10 configurations, leading to out-
of-bounds array writes.
So, in efx_filter_rfs_work(), convert this back into an index (which is
what the remove call in the expiry path expects, anyway).
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"./scripts/get_maintainer.pl -f" does not actually show us David as the
maintainer of drivers/net directories such as team, bonding, phy or dsa.
Adding him in an M: entry of NETWORKING DRIVERS fixes this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa4ixLAAoJEEg/ir3gV/o+PB0IAKlexiYEyID3N3cvG/I0m4Zh
yxIN4H8sUu3kz7dG6dkvpL5Oo5c43/huE+tspOYfFmydMWvOV+DakwqAhkE+KUfe
VIpF0cM7+T8Els8e7OzuT0Zu5ggeN1wU0uPRhAn1F592BH0ppXGBn8WIKTffYb8c
5XeB2JSZyw4yMgk1zurm4tVtFvHbYO7SAkLZZG5E0m7EeIujVWi1lTnhXNi9zdm/
48LoLZ/1Rmx0e/Qpey2fm9HEPRPTgCNSBLEsx2hIDiJG56YyWPH6+N7U9Acf2PaI
lKu2JMqLYe3du8hhPtCbPYH0i74af/LbNCQgXXgPstAI49v+MydlBcv2NX9J6NY=
=nw/Q
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-04-26
This pull request includes fixes for mlx5 core and netdev driver.
Please pull and let me know if there's any problems.
For -stable v4.12
net/mlx5e: TX, Use correct counter in dma_map error flow
For -stable v4.13
net/mlx5: Avoid cleaning flow steering table twice during error flow
For -stable v4.14
net/mlx5e: Allow offloading ipv4 header re-write for icmp
For -stable v4.15
net/mlx5e: DCBNL fix min inline header size for dscp
For -stable v4.16
net/mlx5: Fix mlx5_get_vector_affinity function
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A few fixes for 4.17 but nothing really special. The new ETSI WMM
parameter support for iwlwifi is not technically a bugfix but
important for regulatory compliance.
iwlwifi
* use new ETSI WMM parameters from regulatory database
* fix a regression with the older firmware API 31 (eg. 31.560484.0)
brcmfmac
* fix a double free in nvmam loading fails
rtlwifi
* yet another fix for ant_sel module parameter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJa4aIYAAoJEG4XJFUm622bOnMH/j7LR1jtny0B8MecnkIt82Ar
uRl/dChzygAsPf2siR5bED5BJPMGuZTl9KWo/XsVP9GSZ5bQewXWmkF+7FXmgP98
MJcxnHDVqhIDzNk5BUtAYQSjpucoZVAy/ueVYwiB526XYjRGCf+15Ie9po/AkBPI
Dd+uRhT0hKAJmnXFtSxtIpkN1E8oBHFiHVyi76HELO8y5eyTnUm4Wxxu0l6tl7D1
elaCK1uLaZm+s5CeyOuJwvYT/k7p5b0knLAyjWOAaTWbSyF02FjY7AIaKhjcJH2m
rOoni7vEa8INQFyK77HOi+d06fWxgSprfZ8dLMxurV12NPFpGzcX7a3tYFpquFE=
=lizT
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.17
A few fixes for 4.17 but nothing really special. The new ETSI WMM
parameter support for iwlwifi is not technically a bugfix but
important for regulatory compliance.
iwlwifi
* use new ETSI WMM parameters from regulatory database
* fix a regression with the older firmware API 31 (eg. 31.560484.0)
brcmfmac
* fix a double free in nvmam loading fails
rtlwifi
* yet another fix for ant_sel module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When IGMP snooping is enabled on a bridge, traffic forwarded by an MDB
entry should be sent to both ports member in the MDB's ports list and
mrouter ports.
In case a port needs to be removed from an MDB's ports list, but this
port is also configured as an mrouter port, then do not update the
device so that it will continue to forward traffic through that port.
Fix a copy-paste error that checked that IGMP snooping is enabled twice
instead of checking the port's mrouter state.
Fixes: ded711c87a ("mlxsw: spectrum_switchdev: Consider mrouter status for mdb changes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Colin King <colin.king@canonical.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a duplicate cookie-echo chunk, sctp moves the new
temp asoc's stream out/in into the old asoc, and later frees this
new temp asoc.
But now after this move, the new temp asoc's stream->outcnt is not
cleared while stream->out is set to NULL, which would cause a same
crash as the one fixed in Commit 79d0895140 ("sctp: fix error
path in sctp_stream_init") when freeing this asoc later.
This fix is to clear this outcnt in sctp_stream_update.
Fixes: f952be79ce ("sctp: introduce struct sctp_stream_out_ext")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sctp ipv6 socket also supports v4 addrs, it's possible to
compare two v4 addrs in pf v6 .cmp_addr, sctp_inet6_cmp_addr.
However after Commit 1071ec9d45 ("sctp: do not check port in
sctp_inet6_cmp_addr"), it no longer calls af1->cmp_addr, which
in this case is sctp_v4_cmp_addr, but calls __sctp_v6_cmp_addr
where it handles them as two v6 addrs. It would cause a out of
bounds crash.
syzbot found this crash when trying to bind two v4 addrs to a
v6 socket.
This patch fixes it by adding the process for two v4 addrs in
sctp_inet6_cmp_addr.
Fixes: 1071ec9d45 ("sctp: do not check port in sctp_inet6_cmp_addr")
Reported-by: syzbot+cd494c1dd681d4d93ebb@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding the DSA notifier, we will be sending DSA notifications with
info->master that is going to point to a particular net_device instance.
Our logic in bcm_sysport_map_queues() correctly disambiguates net_device
instances that are not covered by our own driver, but it will not make
sure that info->master points to a particular driver instance that we
are interested in. In a system where e.g: two or more SYSTEMPORT
instances are registered, this would lead in programming two or more
times the queue mapping, completely messing with the logic which does
the queue/port allocation and tracking.
Fix this by looking at the notifier_block pointer which is unique per
instance and allows us to go back to our driver private structure, and
in turn to the backing net_device instance.
Fixes: d156576362 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Script in_netns.sh is a utility function and not its own test so it
shouldn't be part of the TEST_PROGS. The in_netns.sh get used by
run_afpackettests.
To install in_netns.sh without being added to the main run_kselftest.sh
script use the TEST_GEN_PROGS_EXTENDED variable.
Fixes: 5ff9c1a3dd ("selftests: net: add in_netns.sh to TEST_PROGS")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCP repair sequence of operation is to first set the socket in
repair mode, then inject the TCP stats into the socket with repair
socket options, then call connect() to re-activate the socket. The
connect syscall simply returns and set state to ESTABLISHED
mode. As a result Fast Open is meaningless for TCP repair.
However allowing sendto() system call with MSG_FASTOPEN flag half-way
during the repair operation could unexpectedly cause data to be
sent, before the operation finishes changing the internal TCP stats
(e.g. MSS). This in turn triggers TCP warnings on inconsistent
packet accounting.
The fix is to simply disallow Fast Open operation once the socket
is in the repair mode.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier says:
====================
net: mvpp2: Fix hangs when starting some interfaces on 7k/8k
Armada 7K / 8K clock management has recently been reworked, see :
commit c7e92def1e ("clk: mvebu: cp110: Fix clock tree representation")
I have been experiencing overall system hangs on MacchiatoBin when starting
the eth1 interface since then. It turns out some clocks dependencies were
missing in the PPv2 and xmdio driver, the clock rework made this visible.
This is the V2 series, that adds support for the missing 'MG Core clock' in
mvpp2, and fixes an issue with the error path for the axi_clk.
Thanks to Gregory Clement for finding the root cause of this bug.
V2 : Remove all DT patches from this series, they will be merged through
the mvebu tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2.2 IP needs an additional clock named "MG Core clock".
This is required on Armada 7K and 8K.
This commit adds the required clock in mvpp2, making sure it's only
used on PPv2.2.
Fixes: c7e92def1e ("clk: mvebu: cp110: Fix clock tree representation")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When clk_prepare_enable fails for the axi_clk, the mg_clk isn't properly
cleaned up. Add another jump label to handle that case, and make sure we
jump to it in the later error cases.
Fixes: 4792ea04bc ("net: mvpp2: Fix clock resource by adding an optional bus clock")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For very very old generation of the management FW Ethernet port
information table may theoretically not be available. This in
turn will cause the nfp_port structures to not be allocated.
Make sure we don't crash the kernel when there is no eth_tbl:
RIP: 0010:nfp_net_pci_probe+0xf2/0xb40 [nfp]
...
Call Trace:
nfp_pci_probe+0x6de/0xab0 [nfp]
local_pci_probe+0x47/0xa0
work_for_cpu_fn+0x1a/0x30
process_one_work+0x1de/0x3e0
Found while working with broken/development version of management FW.
Fixes: a5950182c0 ("nfp: map mac_stats and vf_cfg BARs")
Fixes: 93da7d9660 ("nfp: provide nfp_port to of nfp_net_get_mac_addr()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36a50a989e ("tipc: fix infinite loop when dumping link monitor
summary") intended to fix a problem with user tool looping when max
number of bearers are enabled.
Unfortunately, the wrong version of the commit was posted, so the
problem was not solved at all.
This commit adds the missing part.
Fixes: 36a50a989e ("tipc: fix infinite loop when dumping link monitor summary")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a flow counter, the modify mask should be the action and
the flow counter. Otherwise the flow counter is not deleted and we'll
get a firmware warning when deleting the remaining destinations on the
same FTE.
It only happens in the presence of flow counter and multiple vport
destinations. If there is only one vport destination, there is no
need to update the FTE when deleting the only vport destination,
we just delete the FTE.
Fixes: ae05831424 ("net/mlx5: Add option to add fwd rule with counter")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After the cited commit, WQE RQ size is calculated based on sw_mtu but it
was not set for representors. This commit fixes that.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When we fail to initialize the RX root namespace, we need
to clean only that and not the entire flow steering.
Currently the code may try to clean the flow steering twice
on error witch leads to null pointer deference.
Make sure we clean correctly.
Fixes: fba53f7b57 ("net/mlx5: Introduce mlx5_flow_steering structure")
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case of a dma_mapping_error, do not use wi->num_dma
as a parameter for dma unmap function because it's yet
to be set, and holds an out-of-date value.
Use actual value (local variable num_dma) instead.
Fixes: 34802a42b3 ("net/mlx5e: Do not modify the TX SKB")
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding the vector offset when calling to mlx5_vector2eqn() is wrong.
This is because mlx5_vector2eqn() checks if EQ index is equal to vector number
and the fact that the internal completion vectors that mlx5 allocates
don't get an EQ index.
The second problem here is that using effective_affinity_mask gives the same
CPU for different vectors.
This leads to unmapped queues when calling it from blk_mq_rdma_map_queues().
This doesn't happen when using affinity_hint mask.
Fixes: 2572cf57d7 ("mlx5: fix mlx5_get_vector_affinity to start from completion vector 0")
Fixes: 05e0cc84e0 ("net/mlx5: Fix get vector affinity helper function")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
When the trust state is set to dscp and the netdev is down, the inline
header size is not updated. When netdev is up, the inline header size
stays at L2 instead of IP.
Fix this issue by updating the private parameter when the netdev is in
down so that when netdev is up, it picks up the right header size.
Fixes: fbcb127e89 ("net/mlx5e: Support DSCP trust state ...")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For ICMPv4, the checksum is calculated from the ICMP headers and data.
Since the ICMPv4 checksum doesn't cover the IP header, we can allow to
do L3 header re-write for this protocol.
Fixes: bdd66ac0ae ('net/mlx5e: Disallow TC offloading of unsupported match/action combinations')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Daniel Borkmann says:
====================
pull-request: bpf 2018-04-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix to clear the percpu metadata_dst that could otherwise carry
stale ip_tunnel_info, from William.
2) Fix that reduces the number of passes in x64 JIT with regards to
dead code sanitation to avoid risk of prog rejection, from Gianluca.
3) Several fixes of sockmap programs, besides others, fixing a double
page_put() in error path, missing refcount hold for pinned sockmap,
adding required -target bpf for clang in sample Makefile, from John.
4) Fix to disable preemption in __BPF_PROG_RUN_ARRAY() paths, from Roman.
5) Fix tools/bpf/ Makefile with regards to a lex/yacc build error
seen on older gcc-5, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build error found with Ubuntu shipped gcc-5
~/git/bpf/tools/bpf$ make all
Auto-detecting system features:
... libbfd: [ OFF ]
... disassembler-four-args: [ OFF ]
CC bpf_jit_disasm.o
LINK bpf_jit_disasm
CC bpf_dbg.o
/home/john/git/bpf/tools/bpf/bpf_dbg.c: In function ‘cmd_load’:
/home/john/git/bpf/tools/bpf/bpf_dbg.c:1077:13: warning: ‘cont’ may be used uninitialized in this function [-Wmaybe-uninitialized]
} else if (matches(subcmd, "pcap") == 0) {
^
LINK bpf_dbg
CC bpf_asm.o
make: *** No rule to make target `bpf_exp.yacc.o', needed by `bpf_asm'. Stop.
Fixes: 5a8997f207 ("tools: bpf: respect output directory during build")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The function rds_ib_setup_qp is calling rds_ib_get_client_data and
should correspondingly call rds_ib_dev_put. This call was lost in
the non-error path with the introduction of error handling done in
commit 3b12f73a5c ("rds: ib: add error handle")
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal CLC socket should exist till the SMC-socket is released.
Function tcp_listen_worker() releases the internal CLC socket of a
listen socket, if an smc_close_active() is called. This function
is called for the final release(), but it is called for shutdown
SHUT_RDWR as well. This opens a door for protection faults, if
socket calls using the internal CLC socket are called for a
shutdown listen socket.
With the changes of
commit 3d50206759 ("net/smc: simplify wait when closing listen socket")
there is no need anymore to release the internal CLC socket in
function tcp_listen_worker((). It is sufficient to release it in
smc_release().
Fixes: 127f497058 ("net/smc: release clcsock from tcp_listen_worker")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Reported-by: syzbot+9045fc589fcd196ef522@syzkaller.appspotmail.com
Reported-by: syzbot+28a2c86cf19c81d871fa@syzkaller.appspotmail.com
Reported-by: syzbot+9605e6cace1b5efd4a0a@syzkaller.appspotmail.com
Reported-by: syzbot+cf9012c597c8379d535c@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MDIO busses will error out when trying to read a phy address with no
phy present at that address. In that case, probing the bus will fail
because __mdiobus_register() is scanning the bus for all possible phys
addresses.
In case MII_PHYSID1 returns -EIO or -ENODEV, consider there is no phy at
this address and set the phy ID to 0xffffffff which is then properly
handled in get_phy_device().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2a5418a13f ("bpf: improve dead code sanitizing") replaced dead
code with a series of ja-1 instructions, for safety. That made JIT
compilation much more complex for some BPF programs. One instance of such
programs is, for example:
bool flag = false
...
/* A bunch of other code */
...
if (flag)
do_something()
In some cases llvm is not able to remove at compile time the code for
do_something(), so the generated BPF program ends up with a large amount
of dead instructions. In one specific real life example, there are two
series of ~500 and ~1000 dead instructions in the program. When the
verifier replaces them with a series of ja-1 instructions, it causes an
interesting behavior at JIT time.
During the first pass, since all the instructions are estimated at 64
bytes, the ja-1 instructions end up being translated as 5 bytes JMP
instructions (0xE9), since the jump offsets become increasingly large (>
127) as each instruction gets discovered to be 5 bytes instead of the
estimated 64.
Starting from the second pass, the first N instructions of the ja-1
sequence get translated into 2 bytes JMPs (0xEB) because the jump offsets
become <= 127 this time. In particular, N is defined as roughly 127 / (5
- 2) ~= 42. So, each further pass will make the subsequent N JMP
instructions shrink from 5 to 2 bytes, making the image shrink every time.
This means that in order to have the entire program converge, there need
to be, in the real example above, at least ~1000 / 42 ~= 24 passes just
for translating the dead code. If we add this number to the passes needed
to translate the other non dead code, it brings such program to 40+
passes, and JIT doesn't complete. Ultimately the userspace loader fails
because such BPF program was supposed to be part of a prog array owner
being JITed.
While it is certainly possible to try to refactor such programs to help
the compiler remove dead code, the behavior is not really intuitive and it
puts further burden on the BPF developer who is not expecting such
behavior. To make things worse, such programs are working just fine in all
the kernel releases prior to the ja-1 fix.
A possible approach to mitigate this behavior consists into noticing that
for ja-1 instructions we don't really need to rely on the estimated size
of the previous and current instructions, we know that a -1 BPF jump
offset can be safely translated into a 0xEB instruction with a jump offset
of -2.
Such fix brings the BPF program in the previous example to complete again
in ~9 passes.
Fixes: 2a5418a13f ("bpf: improve dead code sanitizing")
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The percpu metadata_dst might carry the stale ip_tunnel_info
and cause incorrect behavior. When mixing tests using ipv4/ipv6
bpf vxlan and geneve tunnel, the ipv6 tunnel info incorrectly uses
ipv4's src ip addr as its ipv6 src address, because the previous
tunnel info does not clean up. The patch zeros the fields in
ip_tunnel_info.
Signed-off-by: William Tu <u9012063@gmail.com>
Reported-by: Yifeng Sun <pkusunyifeng@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
