This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch merges the prepare data functions.
This allows to define a single access to prepare data service.
This prepares integration for mmci host ops.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-Introduces dma_priv pointer to define specific
needs for each dma engine. This patch is needed to prepare
sdmmc variant with internal dma which not use dmaengine API.
-Moves next cookie to mmci host structure to share same cookie
management between all variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch creates a common mmci_dma_setup/release which calls
dma_setup/release callbacks of mmci_host_ops and manages
common features like use_dma... If there is a fallbacks to
pio mode, dma functions must check use_dma.
error management:
-mmci_dmae_setup fail if Tx and Rx dma channels are not defined
-qcom_dma_setup fail if one of both dma channels is not defined,
Qcom has no specific resource to release, just mmci dmae resource.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on TI's AM654 devices.
Therefore, add a new compatible, AM654 specific quirks
and a new AM654 specific set_clock function which
configures the PHY in a sane way.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the driver passes platform data as a global structure
and uses the .data of of_device_id to pass the soc_ctl_map. To
make the implementation more flexible add a single data structure
that incorporates both of the above and pass it in the .data of
of_device_id.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new compatible to use the host controller driver with the
MMC PHY on TI's AM654 SOCs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when gate MSDC0_HCLK, access register will hang, even the MSDC driver
will never accessing register after HCLK was gated, but for safety, need
gate the bus_clk(which used to access register) too.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On MT2712 MSDC0/3, HCLK/bus-clk need gate/ungate together,
or will hang when access MSDC register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "fall-through:"
comment with a proper "fall through", which is what GCC is
expecting to find.
Addresses-Coverity-ID: 1373880 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the
"deliberate fall-through" comment with a proper "fall through"
at the bottom of the case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 1373887 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384
fix checkpatch --strict issues:
-CHECK: Avoid using bool structure members because of possible alignment
issues - see: https://lkml.org/lkml/2017/11/21/384
-WARNING: Avoid using bool as bitfield. Prefer bool bitfields as
unsigned int or u<8|16|32>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the dma_inprogress into mmci dma interfaces.
This allows to simplify and prepare the next dma callbacks
for mmci host ops. dma_inprogress is called in mmci_dma_data_error
and mmci_dma_finalize.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the management of dma map/unmap into
mmci dma interfaces. This allows to simplify and prepare the next dma
callbacks for mmci host ops.
mmci_dma_unmap was called in mmci_data_irq & mmci_cmd_irq functions
and can be integrated in mmci_dma_data_error.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r8a7744 SoC. Renesas RZ/G1N (R8A7744) MMCIF is identical
to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r8a7744 SoC. Renesas RZ/G1N (R8A7744) SDHI is identical
to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The OMAP HSMMC driver has some elaborate and hairy handling for
passing GPIO card detect and write protect lines from a boardfile
into the driver: the machine defines a struct omap2_hsmmc_info
that is copied into struct omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() in arch/arm/mach-omap2/hsmmc.c.
However the .gpio_cd and .gpio_wp fields are not copied from
omap2_hsmmc_info to omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() so they remain unused. The only platform
defining omap2_hsmmc_info also define both to -1, unused.
It turn out there are no boardfiles passing any valid GPIO
lines into the OMAP HSMMC driver at all. And since we are not
going to add any more OMAP2 boardfiles, we can delete this
card detect and write protect handling altogether.
This seems to also fix a bug: the card detect callback
mmc_gpio_get_cd() in the slot GPIO core needs to be called
by drivers utilizing slot GPIO. It appears the the boardfile
quirks were not doing this right, so this would only get
called for boardfiles, i.e. since no boardfile was using it,
never.
Just assign mmc_gpio_get_cd() unconditionally to omap_hsmmc_ops
.get_cd() so card detects from the device tree works.
AFAICT card detect with GPIO lines assigned from
mmc_of_parse() are not working at the moment, but that is
no regression since it probably never worked.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cover detection appears to be a feature protecting the SD
card on mobile phones with a slide-cover, such as some Nokia
phones. The idea seems to be to not allow access to the
SD card when the cover is open.
It is only usable with platform data from board files, but
no board file in the kernel is using it, yet it takes up
a sizeable chunk of code in the OMAP HSMMC driver.
Since we do not add new board files for the OMAPs any target
that need this should anyway reimplement it properly using
the device tree, so delete this legacy code.
The driver is marked as orphan in MAINTAINERS by the way.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sd8686 "libertas" SDIO adapter's power is controlled with WLAN_RST
and WLAN_PD pins -- pretty much the same way as sd8787. Allow building
the power sequencing driver along with the libertas Wi-Fi driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
If the retrieveal is successful, we also request the IRQ.
As a result the private subdriver data can be removed
entirely.
Cc: Weijun Yang <york.yang@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform data for the PXAv3 driver allows passing a card
detect GPIO, but this code is not used in the kernel.
In order to not encourage the use of the old global GPIO
numberspace we need to remove this.
Card detect (and write protect) GPIO can easily be added into
the driver using machine descriptor tables instead, and the
descriptor-based (gpiod) variants of the slot GPIO APIs.
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).
Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If hosts provides ops->adma_write_desc, we should not fall back to the
general sdhci_adma_write_desc().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.
renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
longer than device claims to support [len=126976] [max=65536]
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
and added comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC controller is also a new timing mode controller, but it doesn't
have the timing mode switch. It does however have signal delay and
calibration controls, typical of Allwinner MMC controllers that support
the new timing mode.
Enable the new timing mode setting for the A64 eMMC controller. This
also enables MMC HS-DDR modes, which gives higher throughput for eMMC
chips that support it, and can deliver such throughput.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer sunxi mmc controller variants support what they call the "new
timing mode". Support for this was implemented in two ways, according
to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc
controllers had switches to select which mode was used. Both switches
had to be set to the same setting. This variant was denoted with the
.has_timings_switch field in the sunxi_mmc_cfg structure. This hardware
is only seen on the A83T.
The second type did away with the old timing mode. The clock controller
no longer had the mode selection or clock delay setting bits. In some
cases the mmc controller retained its mode selection bit, but this
always needed to be set to the new mode, or instabilities would occur.
In a few cases, such as the A64 and H6 eMMC controller, the mode
selection bit is gone, but the controller still behaves like the new
timing mode, requiring the module clock to be double the card clock
in DDR transfer modes. This variant is denoted with the
.needs_new_timings field.
This patch adds more comments explaining the two fields, as well as
the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify
its meaning.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When Host Version 4 Enable is set to 1, SDMA uses ADMA System Address
register (05Fh-058h) instead of using register (000h-004h) to indicate
its system address of data location. The register (000h-004h) is
re-assigned to 32-bit Block Count and Auto CMD23 argument, so then SDMA
may use Auto CMD23.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.
This patch add this new mode support.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.
Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.
For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the SD host controller specification version 4.10, when
Host Version 4 is enabled, SDMA uses ADMA System Address register
(05Fh-058h) instead of using SDMA System Address register to
support both 32-bit and 64-bit addressing.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode. This patch introduced an interface to enable
v4 mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix inconsistent IS_ERR and PTR_ERR in tegra_sdhci_init_pinctrl_info,
the proper pointer to be passed as argument is 'pinctrl_state_1v8'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rerun the pad calibration procedure before sdhci_request() if
the 100 ms recalibration interval has been exceeded.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement HS400 specific delay line calibration procedure. This is a
Tegra specific procedure and has to be performed regardless whether
enhanced strobe or HS400 tuning is used.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse and program the HS400 DQS trim value from DT. Program a fallback
value in case the property is missing.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement tegra210_sdhci_writew() to disable card clock and issue a
reset when the tuning command is sent. This is done to prevent an
intermittent hang with around 10 % failure rate during tuning.
Add tegra186_sdhci_ops because this workaround is specific to Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tegra_sdhci_writew() defers the write to SDHCI_TRANSFER_MODE until
SDHCI_COMMAND is written. This is not necessary on Tegra210 and Tegra186
and it breaks read-modify-write operations on SDHCI_TRANSFER_MODE
because writes to SDHCI_TRANSFER_MODE aren't visible until SDHCI_COMMAND
has been written to. This results in tuning failures on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new sdhci_ops struct for Tegra210 and Tegra186 which doesn't
set the custom tuning callback used on previous SoC generations.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
