This patch adds new PCI and subsystem ID's that finally made the spec. It
also include a name change for one controller. I know there's a lot of
duplicat names but the fw folks wanted this for the different implementations.
Even though the same ASIC is used it may be embedded on some platforms,
standup card in others, and a mezzanine in other servers.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We seem to use both asm-offsets.* and asm_offsets.*
Signed-off-by: Michal K. K. Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update Documentation/usb/proc_usb_info.txt:
- remove some trailing whitespace
- add a blank line before each T: line to match current kernel
and to make the text more readable.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update i810fb documentation to describe new features and configuration
changes.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernel connector - new userspace <-> kernel space easy to use
communication module which implements easy to use bidirectional
message bus using netlink as it's backend. Connector was created to
eliminate complex skb handling both in send and receive message bus
direction.
Connector driver adds possibility to connect various agents using as
one of it's backends netlink based network. One must register
callback and identifier. When driver receives special netlink message
with appropriate identifier, appropriate callback will be called.
From the userspace point of view it's quite straightforward:
socket();
bind();
send();
recv();
But if kernelspace want to use full power of such connections, driver
writer must create special sockets, must know about struct sk_buff
handling... Connector allows any kernelspace agents to use netlink
based networking for inter-process communication in a significantly
easier way:
int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
void cn_netlink_send(struct cn_msg *msg, u32 __groups, int gfp_mask);
struct cb_id
{
__u32 idx;
__u32 val;
};
idx and val are unique identifiers which must be registered in
connector.h for in-kernel usage. void (*callback) (void *) - is a
callback function which will be called when message with above idx.val
will be received by connector core.
Using connector completely hides low-level transport layer from it's
users.
Connector uses new netlink ability to have many groups in one socket.
[ Incorporating many cleanups and fixes by myself and
Andrew Morton -DaveM ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch adds Documentation/scsi/scs_eh.txt. I've chosen plain
text over DocBook as most other scsi docs are in plain text and it's
more accessible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove S4BIOS support. It is pretty useless, and only ever worked for _me_
once. (I do not think anyone else ever tried it). It was in feature-removal
for a long time, and it should have been removed before.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the most trivial from Rusty's trivial patches:
- spelling fixes
- remove duplicate includes
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch fixes the following spelling errors in Documentation/
- double "the"
- Several misspellings of function/functionality
- infomation
- memeory
- Recieved
- wether
and possibly others which I forgot ;-)
Trailing whitespaces on the same line as the typo are also deleted.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update RCU documentation based on discussions and review of RCU-based tree
patches. Add an introductory whatisRCU.txt file.
Signed-off-by: <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the number of supported AoE slot addresses per AoE shelf
address to 16.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make data caching behavior selectable on a per-open basis instead of
per-mount. Compatibility for the old mount options 'kernel_cache' and
'direct_io' is retained in the userspace library (version 2.4.0-pre1 or
later).
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the FUSE device handling functions.
This contains the following files:
o dev.c
- fuse device operations (read, write, release, poll)
- registers misc device
- support for sending requests to userspace
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The URL for Documentation/sparse is wrong now that it is in git.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch brings the now out-of-date Documentation/filesystems/vfs.txt
back to life. Thanks to Carsten Otte, Trond Myklebust, and Anton
Altaparmakov for their help on updating this documentation.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are minor changes in command line options in kexec-tools for kdump.
This patch updates the documentation to reflect those changes.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Someone complained about the docs for vm_overcommit_memory being wrong.
This patch copies the text from the vm documentation into procfs.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Documentation for how the ISA DMA controller is handled in the kernel.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new document describing the major kernel trees and how to apply their
patches.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the hacking guide, before CONFIG_PREEMPT_RT goes in and it needs
rewriting again.
Changes include modernization of quotes, removal of most references to
bottom halves (some mention required because we still use bh in places to
mean softirq).
It would be nice to have a discussion of sparse and various annotations.
Please send patches straight to akpm.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (authored)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Coordinated Video Timings (CVT) is the latest standard approved by VESA
concerning video timings generation. It addresses the limitation of GTF which
is designed mainly for CRT displays. CRT's have a high blanking requirement
(as much as 25% of the horizontal frame length) which artificially increases
the pixelclock. Digital displays, on the other hand, needs to conserve the
pixelclock as much as possible. The GTF also does not take into account the
different aspect ratios in its calculation.
The new function added is fb_find_mode_cvt(). It is called by fb_find_mode()
if it recognizes a mode option string formatted for CVT. The format is:
<xres>x<yres>[M][R][-<bpp>][<at-sign><refresh>][i][m]
The 'M' tells the function to calculate using CVT. On it's own, it will
compute a timing for CRT displays at 60Hz. If the 'R' is specified, 'reduced
blanking' computation will be used, best for flatpanels. The 'i' and the 'm'
is for 'interlaced mode' and 'with margins' respectively.
To determine if CVT was used, check for dmesg for something like this:
CVT Mode - <pix>M<n>[-R], ie: .480M3-R (800x600 reduced blanking)
where: pix - product of xres and yres, in MB
M - is a CVT mode
n - the aspect ratio (3 - 4:3; 4 - 5:4; 9 - 16:9, 15:9; A - 16:10)
-R - reduced blanking
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a framebuffer driver for the Cyberblade/i1 graphics core.
Currently tridenfb claims to support the cyberblade/i1 graphics core. This
is of very limited truth. Even vesafb is faster and provides more working
modes and a much better quality of the video signal. There is a great
number of bugs in tridentfb ... but most often it is impossible to decide
if these bugs are real bugs or if fixing them for the cyberblade/i1 core
would break support for one of the other supported chips.
Tridentfb seems to be unmaintained,and documentation for most of the
supported chips is not available. So "fixing" cyberblade/i1 support inside
of tridentfb was not an option, it would have caused numerous
if(CYBERBLADEi1) else ... cases and would have rendered the code to be
almost unmaintainable.
A first version of this driver was published on 2005-07-31. A fix for a
bug reported by Jochen Hein was integrated as well as some changes
requested by Antonino A. Daplas.
A message has been added to tridentfb to inform current users of tridentfb
to switch to cyblafb if the cyberblade/i1 graphics core is detected.
This patch is one logical change, but because of the included documentation
it is bigger than 70kb. Therefore it is not sent to lkml and
linux-fbdev-devel,
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
OVERVIEW
V9FS is a distributed file system for Linux which provides an
implementation of the Plan 9 resource sharing protocol 9P. It can be
used to share all sorts of resources: static files, synthetic file servers
(such as /proc or /sys), devices, and application file servers (such as
FUSE).
BACKGROUND
Plan 9 (http://plan9.bell-labs.com/plan9) is a research operating
system and associated applications suite developed by the Computing
Science Research Center of AT&T Bell Laboratories (now a part of
Lucent Technologies), the same group that developed UNIX , C, and C++.
Plan 9 was initially released in 1993 to universities, and then made
generally available in 1995. Its core operating systems code laid the
foundation for the Inferno Operating System released as a product by
Lucent Bell-Labs in 1997. The Inferno venture was the only commercial
embodiment of Plan 9 and is currently maintained as a product by Vita
Nuova (http://www.vitanuova.com). After updated releases in 2000 and
2002, Plan 9 was open-sourced under the OSI approved Lucent Public
License in 2003.
The Plan 9 project was started by Ken Thompson and Rob Pike in 1985.
Their intent was to explore potential solutions to some of the
shortcomings of UNIX in the face of the widespread use of high-speed
networks to connect machines. In UNIX, networking was an afterthought
and UNIX clusters became little more than a network of stand-alone
systems. Plan 9 was designed from first principles as a seamless
distributed system with integrated secure network resource sharing.
Applications and services were architected in such a way as to allow
for implicit distribution across a cluster of systems. Configuring an
environment to use remote application components or services in place
of their local equivalent could be achieved with a few simple command
line instructions. For the most part, application implementations
operated independent of the location of their actual resources.
Commercial operating systems haven't changed much in the 20 years
since Plan 9 was conceived. Network and distributed systems support is
provided by a patchwork of middle-ware, with an endless number of
packages supplying pieces of the puzzle. Matters are complicated by
the use of different complicated protocols for individual services,
and separate implementations for kernel and application resources.
The V9FS project (http://v9fs.sourceforge.net) is an attempt to bring
Plan 9's unified approach to resource sharing to Linux and other
operating systems via support for the 9P2000 resource sharing
protocol.
V9FS HISTORY
V9FS was originally developed by Ron Minnich and Maya Gokhale at Los
Alamos National Labs (LANL) in 1997. In November of 2001, Greg Watson
setup a SourceForge project as a public repository for the code which
supported the Linux 2.4 kernel.
About a year ago, I picked up the initial attempt Ron Minnich had
made to provide 2.6 support and got the code integrated into a 2.6.5
kernel. I then went through a line-for-line re-write attempting to
clean-up the code while more closely following the Linux Kernel style
guidelines. I co-authored a paper with Ron Minnich on the V9FS Linux
support including performance comparisons to NFSv3 using Bonnie and
PostMark - this paper appeared at the USENIX/FREENIX 2005
conference in April 2005:
( http://www.usenix.org/events/usenix05/tech/freenix/hensbergen.html ).
CALL FOR PARTICIPATION/REQUEST FOR COMMENTS
Our 2.6 kernel support is stabilizing and we'd like to begin pursuing
its integration into the official kernel tree. We would appreciate any
review, comments, critiques, and additions from this community and are
actively seeking people to join our project and help us produce
something that would be acceptable and useful to the Linux community.
STATUS
The code is reasonably stable, although there are no doubt corner cases
our regression tests haven't discovered yet. It is in regular use by several
of the developers and has been tested on x86 and PowerPC
(32-bit and 64-bit) in both small and large (LANL cluster) deployments.
Our current regression tests include fsx, bonnie, and postmark.
It was our intention to keep things as simple as possible for this
release -- trying to focus on correctness within the core of the
protocol support versus a rich set of features. For example: a more
complete security model and cache layer are in the road map, but
excluded from this release. Additionally, we have removed support for
mmap operations at Al Viro's request.
PERFORMANCE
Detailed performance numbers and analysis are included in the FREENIX
paper, but we show comparable performance to NFSv3 for large file
operations based on the Bonnie benchmark, and superior performance for
many small file operations based on the PostMark benchmark. Somewhat
preliminary graphs (from the FREENIX paper) are available
(http://v9fs.sourceforge.net/perf/index.html).
RESOURCES
The source code is available in a few different forms:
tarballs: http://v9fs.sf.net
CVSweb: http://cvs.sourceforge.net/viewcvs.py/v9fs/linux-9p/
CVS: :pserver:anonymous@cvs.sourceforge.net:/cvsroot/v9fs/linux-9p
Git: rsync://v9fs.graverobber.org/v9fs (webgit: http://v9fs.graverobber.org)
9P: tcp!v9fs.graverobber.org!6564
The user-level server is available from either the Plan 9 distribution
or from http://v9fs.sf.net
Other support applications are still being developed, but preliminary
version can be downloaded from sourceforge.
Documentation on the protocol has historically been the Plan 9 Man
pages (http://plan9.bell-labs.com/sys/man/5/INDEX.html), but there is
an effort under way to write a more complete Internet-Draft style
specification (http://v9fs.sf.net/rfc).
There are a couple of mailing lists supporting v9fs, but the most used
is v9fs-developer@lists.sourceforge.net -- please direct/cc your
comments there so the other v9fs contibutors can participate in the
conversation. There is also an IRC channel: irc://freenode.net/#v9fs
This part of the patch contains Documentation, Makefiles, and configuration
file changes.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a set of primitives to do reference counting for objects that are looked
up without locks using RCU.
Signed-off-by: Ravikiran Thirumalai <kiran_th@gmail.com>
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- cx88-dvb has been incorrectly reporting the card name instead of frontend name
- Removes a bad PCI subsystem ID for saa713x Sabrent card
- Renames DVICO --> DViCO for bttv.
- #include <linux/config.h> no longer needed.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add saa713x card #65 Kworld V-Stream Studio TV Terminator
Signed-off-by: James R Webb <jrwebb@qwest.net>
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove $Id CVS logs for V4L files
- linux/version.h replaced by linux/utsname.h
- Add new Digimatrix card and LG TAPC Mini tuner for it
Signed-off-by: Hermann Pitton <hermann.pitton@onlinehome.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove $Id CVS logs for V4L files
- Added DVICO FusionHDTV 5 Lite card.
- Added Acorp Y878F.
- CodingStyle fixes.
- Added tuner_addr to bttv cards structure.
- linux/version.h replaced by linux/utsname.h on bttvp.h
- kernel module for acquiring RDS data from a SAA6588.
- Allow multiple open() and reading calls to /dev/radio on bttv-driver.c
- added i2c address for lgdt330x.
Signed-off-by: Hans J. Koch <koch@hjk-az.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove $Id CVS logs for V4L files
- Included newer cards.
- Added a new NEC protocol for ir based on pulse distance.
- Enable ATSC support for DViCO FusionHDTV5 Gold.
- Added tuner LG NTSC (TALN mini series).
- Fixed tea5767 autodetection.
- Resolve more tuner types.
- Commented debug function removed from mainstream.
- Remove comments from mainstream. Still on development tree.
- linux/version dependencies removed.
- BTSC Lang1 now is set to auto_stereo mode.
- New tuner standby API.
- i2c-core.c uses hexadecimal for the i2c address, so it should stay consistent.
Signed-off-by: Uli Luckas <luckas@musoft.de>
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Hermann Pitton <hermann.pitton@onlinehome.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated Documentation
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated documentation
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch aggregates all modifications in the -mm tree and adds
complete ringtone support.
The following features are supported:
- keyboard full support
- LCD full support
- LED full support
- dialtone full support
- ringtone full support
- audio playback via generic usb audio diver
- audio record via generic usb audio diver
For driver documentation see: Documentation/input/yealink.txt
For vendor documentation see: http://yealink.com
Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
