The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
The WinSystems WS16C48 provides the following registers:
Offset 0x0-0x5: Port 0-5 I/O
Offset 0x6: Int_Pending
Offset 0x7: Page/Lock
Offset 0x8-0xA (Page 1): Pol_0-Pol_2
Offset 0x8-0xA (Page 2): Enab_0-Enab_2
Offset 0x8-0xA (Page 3): Int_ID0-Int_ID2
Port 0-5 I/O provides access to 48 lines of digital I/O across six
registers, each bit position corresponding to the respective line.
Writing a 1 to a respective bit position causes that output pin to sink
current, while writing a 0 to the same bit position causes that output
pin to go to a high-impedance state and allows it to be used an input.
Reads on a port report the inverted state (0 = high, 1 = low) of an I/O
pin when used in input mode. Interrupts are supported on Port 0-2.
Int_Pending is a read-only register that reports the combined state of
the INT_ID0 through INT_ID2 registers; an interrupt pending is indicated
when any of the low three bits are set.
The Page/Lock register provides the following bits:
Bit 0-5: Port 0-5 I/O Lock
Bit 6-7: Page 0-3 Selection
For Bits 0-5, writing a 1 to a respective bit position locks the output
state of the corresponding I/O port. Writing the page number to Bits 6-7
selects that respective register page for use.
Pol_0-Pol_2 are accessible when Page 1 is selected. Writing a 1 to a
respective bit position selects the rising edge detection interrupts for
that input line, while writing a 0 to the same bit position selects the
falling edge detection interrupts.
Enab_0-Enab_2 are accessible when Page 2 is selected. Writing a 1 to a
respective bit position enables interrupts for that input line, while
writing a 0 to that same bit position clears and disables interrupts for
that input line.
Int_ID0-Int_ID2 are accessible when Page 3 is selected. A respective bit
when read as a 1 indicates that an edge of the polarity set in the
corresponding polarity register was detected for the corresponding input
line. Writing any value to this register clears all pending interrupts
for the register.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/f59de81e80f7198bcfa9a15615c459c38b5d0e08.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
For the PCIe-IDIO-24 series of devices, the following BARs are
available:
BAR[0]: memory mapped PEX8311
BAR[1]: I/O mapped PEX8311
BAR[2]: I/O mapped card registers
There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS
lines (which may be configured for either output or input). The GPIO
lines are exposed by the following card registers:
Base +0x0-0x2 (Read/Write): FET Outputs
Base +0xB (Read/Write): TTL/CMOS
Base +0x4-0x6 (Read): Isolated Inputs
Base +0x7 (Read): TTL/CMOS
In order for the device to support interrupts, the PLX PEX8311 internal
PCI wire interrupt and local interrupt input must first be enabled.
The following card registers for Change-Of-State may be used:
Base +0x8-0xA (Read): COS Status Inputs
Base +0x8-0xA (Write): COS Clear Inputs
Base +0xB (Read): COS Status TTL/CMOS
Base +0xB (Write): COS Clear TTL/CMOS
Base +0xE (Read/Write): COS Enable
The COS Enable register is used to enable/disable interrupts and
configure the interrupt levels; each bit maps to a group of eight inputs
as described below:
Bit 0: IRQ EN Rising Edge IN0-7
Bit 1: IRQ EN Rising Edge IN8-15
Bit 2: IRQ EN Rising Edge IN16-23
Bit 3: IRQ EN Rising Edge TTL0-7
Bit 4: IRQ EN Falling Edge IN0-7
Bit 5: IRQ EN Falling Edge IN8-15
Bit 6: IRQ EN Falling Edge IN16-23
Bit 7: IRQ EN Falling Edge TTL0-7
An interrupt is asserted when a change-of-state matching the interrupt
level configuration respective for a particular group of eight inputs
with enabled COS is detected.
The COS Status registers may be read to determine which inputs have
changed; if interrupts were enabled, an IRQ will be generated for the
set bits in these registers. Writing the value read from the COS Status
register back to the respective COS Clear register will clear just those
interrupts.
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
All idio-16 library consumers have migrated to the new interface
leveraging the gpio-regmap API. Legacy interface functions and code are
removed as no longer needed.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/651cff1cc3eb57b455a8048121cf6a4d4367f018.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the pci-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/5ba5405c64aca984d5cf3bdbdffa04c325e5a147.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the 104-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1f24a1f18c9a9daa4983713e0a5b53e838d624a8.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
By leveraging the regmap API, the idio-16 library is reduced to simply a
devm_idio_16_regmap_register() function and a configuration structure
struct idio_16_regmap_config.
Legacy functions and code will be removed once all consumers have
migrated to the new idio-16 library interface.
For IDIO-16 devices we have the following IRQ registers:
Base Address +1 (Write): Clear Interrupt
Base Address +2 (Read): Enable Interrupt
Base Address +2 (Write): Disable Interrupt
An interrupt is asserted whenever a change-of-state is detected on any
of the inputs. Any write to 0x2 will disable interrupts, while any read
will enable interrupts. Interrupts are cleared by a write to 0x1.
For 104-IDIO-16 devices, there is no IRQ status register, so software
has to assume that if an interrupt is raised then it was for the
104-IDIO-16 device.
For PCI-IDIO-16 devices, there is an additional IRQ register:
Base Address +6 (Read): Interrupt Status
Interrupt status can be read from 0x6 where bit 2 set indicates that an
IRQ has been generated.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b45081958ab53dfa697f4a8b15f1bfba46718068.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When comparing strings passed to us from configfs, we can pass the page
argument directly to sysfs_streq() and avoid manual string trimming.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here, and __maybe_unused can also be removed.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here, and __maybe_unused can also be removed.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use CONFIG_OF
and of_match_ptr() here, we remove them all.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
CONFIG_OF and of_match_ptr() here, so we remove them all.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here. We remove both CONFIG_OF and of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that IRQ 0
is invalid"), there is no possible for platform_get_irq() to return 0.
And the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Simulated chips use a mutex for synchronization in driver callbacks so
they must not be called from interrupt context. Set the can_sleep field
of the GPIO chip to true to force users to only use threaded irqs.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call is not required because no counterpart
platform_get_drvdata() call is present to leverage the private data of
the driver.
Since the private data is confined to this driver file, external access
is not feasible.
The use of this function appears redundant in the current context of the
driver's implementation.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call, to access the private data of the driver.
Also, the private data is defined in this driver, so there is no risk of
it being accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() call was never used, ever since the driver was
originally added.
It looks like this copy+paste left-over. Possibly the author copied from a
driver that had this line, but also had a remove hook.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() isn't needed for anything. The function is a
simple setter that doesn't change anything in the code. That is because
there isn't a get function and since it has no dependencies it can be
removed.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() was needed when the driver had an explicit
remove function.
That function got removed a while back, so we don't need to keep a pointer
(on 'dev->driver_data') for the private data of the driver anymore.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() was needed when the driver had an explicit
remove function.
That function got removed a while back, so we don't need to keep a pointer
(on 'dev->driver_data') for the private data of the driver anymore.
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to call the dev_err_probe() function directly to print
a custom message when handling an error from platform_get_irq() function as
it is going to display an appropriate error message in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The DS4520 is a 9-bit nonvolatile (NV) I/O expander.
It offers users a digitally programmable alternative
to hardware jumpers and mechanical switches that are
being used to control digital logic node.
Signed-off-by: Okan Sahin <okan.sahin@analog.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to call the dev_err_probe() function directly to print
a custom message when handling an error from platform_get_irq() function as
it is going to display an appropriate error message in case of a failure.
And the code to handle bank->irq = 0 is redundant because
platform_get_irq() do not return 0.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The 104-DIO-48E features an 8254 Counter/Timer chip providing three
counter/timers which can be used for frequency measurement, frequency
output, pulse width modulation, pulse width measurement, event count,
etc. The counter/timers use the same addresses as PPI 0 (addresses 0x0
to 0x3), so a raw_spinlock_t is used to synchronize operations between
the two regmap mappings to prevent clobbering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Driver is so simple, yet there was a room for mistakes.
Reduce their appearance in the future by enabling COMPILE_TEST
option.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Replace the GPLv2 boilerplate text with a nice and short
SPDX header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We have a temporary variable to keep pointer to struct device.
Utilise it inside the ->probe() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is nothing in the driver that requires OF APIs,
make the driver OF independent.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Fix English spelling and grammar in the comments.
While at it, fix the MODULE_AUTHOR() email address format.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/r/65b4ac1a-1128-6e2a-92c0-9bbcca4b760a@infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add missing platform_device.h that used to be implied by of_device.h.
While at it, sort headers alphabetically for better maintenance.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: e91d0f05e6 ("gpio: Explicitly include correct DT includes")
Closes: https://lore.kernel.org/r/65b4ac1a-1128-6e2a-92c0-9bbcca4b760a@infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This can reduce the kernel image size in multiplatform configurations.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Do not parse the devicetree again when the data is already available
from the IRQ subsystem. This follows the example of the ThunderX and
X-Gene GPIO drivers. The ngpio check is needed to avoid a possible
out-of-bounds read.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
of_irq_count(), or eqivalently platform_irq_count(), simply looks up
successively-numbered IRQs until that fails. Since this driver needs to
look up each IRQ anyway to get its virq number, use that existing loop
to count the IRQs at the same time.
The check against SIFIVE_GPIO_MAX functioned as a bounds check for
chip->irq_number. That is now handled by the loop condition.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to convert dev->of_node back to a fwnode_handle.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
If CONFIG_PM=n (e.g. m68k/allmodconfig):
drivers/gpio/gpio-mxc.c:612:12: error: ‘mxc_gpio_runtime_resume’ defined but not used [-Werror=unused-function]
612 | static int mxc_gpio_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpio/gpio-mxc.c:602:12: error: ‘mxc_gpio_runtime_suspend’ defined but not used [-Werror=unused-function]
602 | static int mxc_gpio_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using the non-SET *_PM_OPS to configure the dev_pm_ops
callbacks, and by wrapping the driver.pm initializer insider pm_ptr().
As NOIRQ_SYSTEM_SLEEP_PM_OPS() uses pm_sleep_ptr() internally, the
__maybe_unused annotations for the noirq callbacks are no longer needed,
and can be removed.
Fixes: 3283d820dc ("gpio: mxc: add runtime pm support")
Reported-by: noreply@ellerman.id.au
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
While here update copyright and module author.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Uwe Kleine-König pointed out we still have one resource leak in the mvebu
driver triggered on driver detach. Let's address it with a custom devm
action.
Fixes: 812d47889a ("gpio/mvebu: Use irq_domain_add_linear")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This allows to get rid of a call to pwmchip_remove() in the error path. There
is no .remove function for this driver, so this change fixes a resource leak
when a gpio-mvebu device is unbound.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The pdev member is assigned and not used, drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() call was never used, ever since the driver was
originally added.
It looks like this copy+paste left-over. Possibly the author copied from a
driver that had this line, but also had a remove hook.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is nothing in the driver that requires OF APIs,
make the driver OF independent.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make tps68470_gpio_output() call tps68470_gpio_set() for output-only pins
too, so that the initial value passed to gpiod_direction_output() is
honored for these pins too.
Fixes: 275b13a655 ("gpio: Add support for TPS68470 GPIOs")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
bgpio_init() uses "sz" argument to populate ngpio, which is not
accurate. Instead, read the "ngpios" property from the DT and if it
doesn't exist, use the "sz" argument. With this change, drivers no
longer need to overwrite the ngpio variable after calling bgpio_init().
If the "ngpios" property is specified, bgpio_bits is calculated
as the round up value of ngpio. At the moment, the only requirement
specified is that the round up value must be a multiple of 8 but
it should also be a power of 2 because we provide accessors based
on the bank size in bgpio_setup_accessors().
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
After adding the missing notifier.h header, let's order all includes
alphabetically.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It was supposed to say 'for' not 'fo'.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Each pin drives a separate interrupt in the parent IRQ domain, so there
is no need to set IRQCHIP_MASK_ON_SUSPEND.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Replace open coded variant of gpiochip_irqchip_add_allocated_domain()
in gpiochip_add_irqchip().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The gpiochip_irqchip_add_allocated_domain() can be used
in another place in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Check domain for being an error pointer before assigning it to
the GPIO IRQ chip domain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
As a preparatory patch and for the sake of consistency,
factor out gpiochip_simple_create_domain().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
As a preparatory patch and for the sake of consistency, make
gpiochip_hierarchy_add_domain() return IRQ domain. While at it,
rename it to gpiochip_hierarchy_create_domain() to show
the change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Ideally we should not touch data in the given GPIO chip structure.
Let's become closer to it by avoiding altering fwnode member.
The GPIO library must use fwnode from GPIO device and the drivers
might use one from GPIO chip in case they initialized it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
GPIO library should rely only on the GPIO device's fwnode.
Hence, replace GPIO chip fwnode usage by respective handle
of the GPIO device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
GPIO library should rely only on the GPIO device's fwnode.
Hence, replace GPIO chip fwnode usage by respective OF node
of the GPIO device.
JFYI, this is partial revert of 8afe825502 ("gpiolib: of:
Prepare of_gpiochip_add() / of_gpiochip_remove() for fwnode").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add runtime PM support and allow the GPIO controller to enter
into runtime suspend automatically when not in use to save power.
However, it will automatically resume and enable clocks when a
GPIO or IRQ is requested.
While putting the GPIO module itself into power saving mode may not
have an obvious impact on current dissipation, the function is necessary
because the GPIO module disables its clock when idle. This enables the
system an opportunity to power off the parent subsystem, and this conserves
more power. The typical i.MX8 SoC features up to 8 GPIO controllers, but
most of the controllers often remain unused.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
gpiolib.h uses notifiers but doesn't include <linux/notifier.h>.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
No core changes this time.
New drivers:
- Tegra234 support.
- Qualcomm IPQ5018 support.
- Intel Meteor Lake-S support.
- Qualcomm SDX75 subdriver.
- Qualcomm SPMI-based PM8953 support.
Improvements:
- Fix up support for GPIO3 on the AXP209.
- Push-pull drive configuration support for the AT91 PIO4.
- Fix misc non-urgent bugs in the AMD driver.
- Misc non-urgent improved error handling.
- Misc janitorial and minor improvements.
-----BEGIN PGP SIGNATURE-----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=MMUo
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time
New drivers:
- Tegra234 support
- Qualcomm IPQ5018 support
- Intel Meteor Lake-S support
- Qualcomm SDX75 subdriver
- Qualcomm SPMI-based PM8953 support
Improvements:
- Fix up support for GPIO3 on the AXP209
- Push-pull drive configuration support for the AT91 PIO4
- Fix misc non-urgent bugs in the AMD driver
- Misc non-urgent improved error handling
- Misc janitorial and minor improvements"
* tag 'pinctrl-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: cherryview: Drop goto label
pinctrl: baytrail: invert if condition
pinctrl: baytrail: add warning for BYT_VAL_REG retrieval failure
pinctrl: baytrail: reduce scope of spinlock in ->dbg_show() hook
pinctrl: tegra: avoid duplicate field initializers
dt-bindings: pinctrl: qcom,sdx65-tlmm: add pcie_clkreq function
pinctrl: mlxbf3: remove broken Kconfig 'select'
pinctrl: spear: Remove unused of_gpio.h inclusion
pinctrl: lantiq: Remove unused of_gpio.h inclusion
pinctrl: at91-pio4: check return value of devm_kasprintf()
pinctrl: microchip-sgpio: check return value of devm_kasprintf()
pinctrl: freescale: Fix a memory out of bounds when num_configs is 1
pinctrl: intel: refine ->irq_set_type() hook
pinctrl: intel: refine ->set_mux() hook
pinctrl: baytrail: Use str_hi_lo() helper
lib/string_choices: Add str_high_low() helper
lib/string_helpers: Split out string_choices.h
lib/string_helpers: Add missing header files to MAINTAINERS database
pinctrl: npcm7xx: Add missing check for ioremap
pinctrl:sunplus: Add check for kmalloc
...
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been converted in
the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block
-----BEGIN PGP SIGNATURE-----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=3KNJ
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have two new drivers, some improvements to the core code, lots of
different updates to existing GPIO drivers and some dt-bindings on
top.
There's nothing controversial in here and almost everything has been
in next for more than a week (95% a lot longer than this). The only
thing that has spent less time in next is a new driver so no risk of
regressions.
The single merge pulls in changes that remove all usage of global GPIO
numbers from arch/arm/mach-omap.
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers:
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down
delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been
converted in the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block"
* tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (58 commits)
of: unittest: drop assertions for GPIO hog messages
gpiolib: Drop unused domain_ops memeber of GPIO IRQ chip
gpio: synq: remove unused zynq_gpio_irq_reqres/zynq_gpio_irq_relres
dt-bindings: gpio: gpio-vf610: Add parsing of hogs
gpio: lpc18xx: Remove unused of_gpio.h inclusion
gpio: xra1403: Remove unused of_gpio.h inclusion
gpio: mpc8xxx: Remove unused of_gpio.h inclusion
dt-bindings: gpio: Add Cirrus EP93xx
gpio: mpc8xxx: latch GPIOs state on module load when configured as output
selftests: gpio: gpio-sim: Use same variable name for sysfs pathname
gpio: mlxbf3: Add gpio driver support
gpio: delay: Remove duplicative functionality
gpio: aggregator: Set up a parser of delay line parameters
gpio: aggregator: Support delay for setting up individual GPIOs
gpio: aggregator: Remove CONFIG_OF and of_match_ptr() protections
dt-bindings: gpio: pca9570: add gpio-line-names property
gpiolib: remove unused gpio_cansleep()
gpio: tps65219: add GPIO support for TPS65219 PMIC
gpio: zynq: fix zynqmp_gpio not an immutable chip warning
gpio: davinci: make davinci_gpio_dev_pm_ops static
...
Another busy release for regmap with the second half fo the maple tree
register cache implementation, there's some smaller optimisations that
could be done but this should now be able to replace the rbtree cache
for most devices.
We also had a followup from Aidan MacDonald's refactoring of some of the
regmap-irq interfaces, the conversion is complete so the old interfaces
are removed. This means that even with the new features for the maple
tree cache we'd have a nice negative diffstat were it not for the
addition of a bunch more KUnit coverage.
There's one GPIO patch in here, it was a dependency for a cleanup of an
API in the regmap-irq code for which the gpio-104-dio-48e driver was the
only user.
Highlights:
- The maple tree cache can now load in default values more efficiently,
and is capabale of syncing multiple registers in a single write
during cache sync.
- More KUnit coverage, including some coverage for raw I/O and a dummy
RAM backed cache to support it.
- Removal of several old interfaces in regmap-irq now all the users
have been modernised.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmSZj0cACgkQJNaLcl1U
h9BNdAf+Kjw+WbqDj/glPTAfrth5aPOyheq9stklzY3mE0E+AxAsHd2PrvYwn1Rt
jiAb96CqsVNP3WFVj6vmM/kfonE7xiBzPng2QtIWKJjxM/PYyLJZkElF6VqZz4cz
ftS4GMAWJadOvIMZgtCFOOujTaBoN0ik2ryZYofVvI8e98W89ifLvCv4aRiJ3Qn8
2R4Wk37JvZtIc2q5kaZ+wo+JIXVijlt7gU+9ZMT7BvJu1ot/KXY3Q3npfSK2Bv5u
qDkMWNZoy9kNd035E8rXt2OTzMlxgUu766wpg3YGU2Hqt15N0n5rpgLc2uB24niG
0yiCYbA2NT5J6+P+/VsE/VTBmJwK8w==
=E+Tk
-----END PGP SIGNATURE-----
Merge tag 'regmap-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Another busy release for regmap with the second half of the maple tree
register cache implementation, there's some smaller optimisations that
could be done but this should now be able to replace the rbtree cache
for most devices.
We also had a followup from Aidan MacDonald's refactoring of some of
the regmap-irq interfaces, the conversion is complete so the old
interfaces are removed. This means that even with the new features for
the maple tree cache we'd have a nice negative diffstat were it not
for the addition of a bunch more KUnit coverage.
There's one GPIO patch in here, it was a dependency for a cleanup of
an API in the regmap-irq code for which the gpio-104-dio-48e driver
was the only user.
Highlights:
- The maple tree cache can now load in default values more
efficiently, and is capabale of syncing multiple registers
in a single write during cache sync
- More KUnit coverage, including some coverage for raw I/O
and a dummy RAM backed cache to support it
- Removal of several old interfaces in regmap-irq now all
users have been modernised"
* tag 'regmap-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (23 commits)
regmap: Allow reads from write only registers with the flat cache
regmap: Drop early readability check
regmap: Check for register readability before checking cache during read
regmap: Add test to make sure we don't sync to read only registers
regmap: Add a test case for write only registers
regmap: Add test that writes to write only registers are prevented
regmap: Add debugfs file for forcing field writes
regmap: Don't check for changes in regcache_set_val()
regmap: maple: Implement block sync for the maple tree cache
regmap: Provide basic KUnit coverage for the raw register I/O
regmap: Provide a ram backed regmap with raw support
regmap: Add missing cache_only checks
regmap: regmap-irq: Move handle_post_irq to before pm_runtime_put
regmap: Load register defaults in blocks rather than register by register
regmap: mmio: Allow passing an empty config->reg_stride
regmap-irq: Drop backward compatibility for inverted mask/unmask
regmap-irq: Minor adjustments to .handle_mask_sync()
regmap-irq: Remove support for not_fixed_stride
regmap-irq: Remove type registers
regmap-irq: Remove virtual registers
...
It seems there is no driver that requires custom IRQ chip
domain options. Drop the member and respective code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Up until commit 6a45b0e258 ("gpiolib: Introduce
gpiochip_irqchip_add_domain()") all irq_domains were allocated
by gpiolib itself and thus gpiolib also takes care of freeing it.
With gpiochip_irqchip_add_domain() a user of gpiolib can associate an
irq_domain with the gpio_chip. This irq_domain is not managed by
gpiolib and therefore must not be freed by gpiolib.
Fixes: 6a45b0e258 ("gpiolib: Introduce gpiochip_irqchip_add_domain()")
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver now uses the generic request/release callbacks, so the custom
ones are no longer called. When building with -Woverride-init, gcc produces
a warning about the duplicate entries:
In file included from drivers/gpio/gpio-zynq.c:10:
include/linux/gpio/driver.h:621:43: error: initialized field overwritten [-Werror=override-init]
621 | .irq_request_resources = gpiochip_irq_reqres, \
| ^~~~~~~~~~~~~~~~~~~
drivers/gpio/gpio-zynq.c:611:9: note: in expansion of macro 'GPIOCHIP_IRQ_RESOURCE_HELPERS'
611 | GPIOCHIP_IRQ_RESOURCE_HELPERS,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/gpio/driver.h:621:43: note: (near initialization for 'zynq_gpio_level_irqchip.irq_request_resources')
621 | .irq_request_resources = gpiochip_irq_reqres, \
| ^~~~~~~~~~~~~~~~~~~
drivers/gpio/gpio-zynq.c:625:9: note: in expansion of macro 'GPIOCHIP_IRQ_RESOURCE_HELPERS'
625 | GPIOCHIP_IRQ_RESOURCE_HELPERS,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/gpio/driver.h:622:43: error: initialized field overwritten [-Werror=override-init]
622 | .irq_release_resources = gpiochip_irq_relres
| ^~~~~~~~~~~~~~~~~~~
Removing the old ones has no effect on the driver but avoids the warnings.
Fixes: f569143935 ("gpio: zynq: fix zynqmp_gpio not an immutable chip warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
of_gpio.h shouldn't be used in GPIO drivers. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
of_gpio.h shouldn't be used in GPIO drivers. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
of_gpio.h shouldn't be used in GPIO drivers. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Qoriq and related devices allow reading out state of GPIO set as output.
However, currently on driver's init, all outputs are configured as driven
low. So, any changes to GPIO confiuration will drive all pins (configured
as output) as output-low.
This patch latches state of output GPIOs before any GPIO configuration
takes place. This preserves any output settings done prior to loading
the driver (for example, by u-boot).
Signed-off-by: Michal Smulski <michal.smulski@ooma.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the BlueField-3 SoC GPIO driver.
This driver configures and handles GPIO interrupts. It also enables a user
to manipulate certain GPIO pins via libgpiod tools or other kernel drivers.
The usables pins are defined via the "gpio-reserved-ranges" property.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that GPIO aggregator supports a delay line, drop the duplicative
functionality, i.e. the entire gpio-delay driver.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The aggregator mode can also handle properties of the platform,
that do not belong to the GPIO controller itself. One of such
a property is a signal delay line. Set up a parser to support it.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In some cases the GPIO may require an additional delay after setting
its value. Add support for that into the GPIO forwarder code.
This will be fully enabled for use in the following changes.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
They stop the driver being used with ACPI PRP0001 and are something
I want to avoid being cut and paste into new drivers. Also include
mod_devicetable.h as we struct of_device_id is defined in there.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add the missing check for platform_get_irq() and return error code
if it fails.
The returned error code will be dealed with in
builtin_platform_driver(sifive_gpio_driver) and the driver will not
be registered.
Fixes: f52d6d8b43 ("gpio: sifive: To get gpio irq offset from device tree data")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for TPS65219 PMICs GPIO interface.
3 GPIO pins:
- GPIO0 only is IO but input mode reserved for MULTI_DEVICE_ENABLE usage.
- GPIO1 and GPIO2 are Output only and referred as GPO1 and GPO2 in spec.
GPIO0 is statically configured as input or output prior to Linux boot.
it is used for MULTI_DEVICE_ENABLE function.
This setting is statically configured by NVM.
GPIO0 can't be used as a generic GPIO (specification Table 8-34).
It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when MULTI_DEVICE_EN=1.
Datasheet describes specific usage for non standard GPIO.
Datasheet: https://www.ti.com/lit/ds/symlink/tps65219.pdf
Co-developed-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with
GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not
added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return
-EPROBE_DEFER.
Fixes: 5467801f1f ("gpio: Restrict usage of GPIO chip irq members before initialization")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make the struct irq_chip const and flag it as IRQCHIP_IMMUTABLE,
call gpiochip_disable_irq() in the .irq_mask() callback and
gpiochip_enable_irq() in the .irq_unmask() callback to fix
"gpio gpiochip1: (zynqmp_gpio): not an immutable chip" warning.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This patch fixes the following sprse warnings:
drivers/gpio/gpio-davinci.c:695:1: sparse: warning: symbol 'davinci_gpio_dev_pm_ops' was not declared. Should it be static?
No functional change intended.
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmSGPiIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGxWcH/AoUClfYYbYZYaoI
spQiFQiZEdniE3W/36GKtfJok4ur1Aogb/q99KvfQxFGkH+aLbTgXxJlTqrlmfWk
Kj4uVUecQl2OHOuEM6AVFyK6S4xdTjWS7TKMGIVe4LDQCAsFidgcYbcVrAhQ+s1s
eAOhlfrKMzVgRQ0KsJkn60SoSbVP6RyRfu+QQu24GfNtD8SzN8y0adB1PYXGVWmr
WW8+MqfZ1WIkn+NWW5bn3AEz8AYjQC66EvcWhlAWmyyBuUjIoNhpIgPHp6Vm7s+a
oPvw/VXwDX8NzpN0XYI+eVpsgClWtJ+HUcCSeuExTxrWu7Bewp6MMLeCjvi/lPpe
zKRDgnw=
=hx4k
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmSHIsUACgkQJNaLcl1U
h9AbDQf+OnspdI5uW+X7ObBdB7KvPAXzDd7rMsXOTdp13bciSmaOzl74f0jPNWYU
GVo3a84eIU0YsdBP7M9+42vyUDQctgoBa7yyxZ+hW8gZQbXwgOZGmvWMncankm9n
hTlUbuLiowPzzjLERMDS0T2iJF0aFG7eB8Xghk/Su38HOCJI6fBx7sQlvt+aFK6J
/WzUuAqHng+6T7FHqxerGz/XIfvnRdS8qC9FZ7ySurmopn2AGY4YlifSGmSlPuFt
MM+nGNTOYn8scBAPRQlVCOwv7XOg6XqEvP5UNe8KpKN1rHfgP/B0X3ZbyE58bpPI
lqZzTXmY/dWD27FUc+3779EGLZ+L8w==
=PyzM
-----END PGP SIGNATURE-----
regmap: Merge up v6.4-rc6
The fix for maple tree RCU locking on sync is a dependency for the
block sync code for the maple tree.
Since the legacy exporting is gone with 2f804aca48 ("gpiolib:
Kill unused GPIOF_EXPORT and Co") there is no need to unexport
GPIO on freeing. Remove that call.
Note, the other users of this functionality do that explicitly,
except one SH and one OMAP boardfile which don't free GPIO anyways,
so it is safe to drop the call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When the PMC device is disabled, probing of the Tegra186 GPIO driver
fails because the IRQ domain that is registered by the PMC driver is
not found. The PMC IRQ domain is only used for wake-up and does not
impact GPIO functionality in general. Therefore, if the PMC device is
disabled, skip looking up the PMC IRQ domain to allow the GPIO driver
to be probed.
Signed-off-by: Manish Bhardwaj <mbhardwaj@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230607113104.11761-1-pshete@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The user-space policy of the gpio-sim is that configuration for lines
with offsets outside the bounds of the corresponding bank is ignored,
but gpio-sim is still using that configuration when constructing the
sim. In the case of named lines this results in temporarily allocating
space for names that are not used, and for hogs results in errors being
logged when the gpio-sim attempts to register the out of range hog with
gpiolib:
gpiochip_machine_hog: unable to get GPIO desc: -22
Add checks to filter out any line configuration outside the bounds
of the bank when constructing the sim.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Drivers should be silent when they work correctly. There's no reason to
emit info messages when GPIO lines are hogged. Demote the message to
debug.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Suggested-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When constructing the sim, gpio-sim constructs an array of named lines,
sized based on the largest offset of any named line, and then initializes
that array with the names of all lines, including unnamed hogs with higher
offsets. In doing so it writes NULLs beyond the extent of the array.
Add a check that only named lines are used to initialize the array.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Kent Gibson<warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver implements a GPIO enable/disable delay. It supports a list
of GPIO outputs, which ramp-up/ramp-down delay can be specified at
consumer location.
The main purpose is to address external, passive delays upon line
voltage changes.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that the of_gpiochip_add() doesn't use valid mask, we may
unify GPIO valid mask allocation and initialization. With this
it makes a symmetry to the similar which we done for IRQ chip.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is a common API to allocate a mask, but more than one duplicative
counterparts. Consolidate the latter into a single common API beneath.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no use of the GPIOF_OPEN_* in the kernel. Kill it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no use of the GPIOF_EXPORT in the kernel. Kill it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
arch/arm/mach-omap[12].
The patches have been reviewed and tested by everyone
who showed interest which was one person that tested
on OSK1 and Nokia 770, and we smoked out the bugs and
also addressed all review comments.
Any remaining problems can certainly be fixed in-tree.
-----BEGIN PGP SIGNATURE-----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=fMmV
-----END PGP SIGNATURE-----
Merge tag 'gpio-omap-descriptors-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into gpio/for-next
This removes all usage of global GPIO numbers from
arch/arm/mach-omap[12].
The patches have been reviewed and tested by everyone
who showed interest which was one person that tested
on OSK1 and Nokia 770, and we smoked out the bugs and
also addressed all review comments.
Any remaining problems can certainly be fixed in-tree.
This change checks if we have the necessary permission to
access the GPIO. For devices that have support for virtualisation
we need to check both the TEGRA186_GPIO_VM_REG and the
TEGRA186_GPIO_SCR_REG registers. For device that do not have
virtualisation support for GPIOs we only need to check the
TEGRA186_GPIO_SCR_REG register.
Signed-off-by: Manish Bhardwaj <mbhardwaj@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The TWL4030 GPIO driver has a custom platform data .set_up()
callback to call back into the platform and do misc stuff such
as hog and export a GPIO for WLAN PWR on a specific OMAP3 board.
Avoid all the kludgery in the platform data and the boardfile
and just put the quirks right into the driver. Make it
conditional on OMAP3.
I think the exported GPIO is used by some kind of userspace
so ordinary DTS hogs will probably not work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In fact the device with chip id 0xD283 is called NCT6126D, and that is
the chip id the Nuvoton code was written for. Correct that name to avoid
confusion, because a NCT6116D in fact exists as well but has another
chip id, and is currently not supported.
The look at the spec also revealed that GPIO group7 in fact has 8 pins,
so correct the pin count in that group as well.
Fixes: d0918a84af ("gpio-f7188x: Add GPIO support for Nuvoton NCT6116")
Reported-by: Xing Tong Wu <xingtong.wu@siemens.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Utilize a temporary variable to calculate number of ctx from ngpio
inside ->probe() implementation.
While at it, include math.h for using DIV_ROUND_UP().
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
sa1100_init_gpio() is declared in a machine specific header so it
can be called from platform code, but the definition is in the device
driver, which causes a warning:
drivers/gpio/gpio-sa1100.c:310:13: error: no previous prototype for 'sa1100_init_gpio' [-Werror=missing-prototypes]
It's already possible to include mach/generic.h from drivers, so add
this one here as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip_add() function to handle removal for us.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
If static allocation and dynamic allocation GPIOs are present,
dynamic allocation pollutes the numberspace for static allocation,
causing static allocation to fail.
Enforce dynamic allocation above GPIO_DYNAMIC_BASE.
Seen on a GTA04 when omap-gpio (static) and twl-gpio (dynamic)
raced:
[some successful registrations of omap_gpio instances]
[ 2.553833] twl4030_gpio twl4030-gpio: gpio (irq 145) chaining IRQs 161..178
[ 2.561401] gpiochip_find_base: found new base at 160
[ 2.564392] gpio gpiochip5: (twl4030): added GPIO chardev (254:5)
[ 2.564544] gpio gpiochip5: registered GPIOs 160 to 177 on twl4030
[...]
[ 2.692169] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[ 2.697357] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[ 2.703643] gpiochip_find_base: found new base at 178
[ 2.704376] gpio gpiochip6: (omap-gpmc): added GPIO chardev (254:6)
[ 2.704589] gpio gpiochip6: registered GPIOs 178 to 181 on omap-gpmc
[...]
[ 2.840393] gpio gpiochip7: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 2.849365] gpio gpiochip7: (gpio-160-191): GPIO integer space overlap, cannot add chip
[ 2.857513] gpiochip_add_data_with_key: GPIOs 160..191 (gpio-160-191) failed to register, -16
[ 2.866149] omap_gpio 48310000.gpio: error -EBUSY: Could not register gpio chip
On that device it is fixed invasively by
commit 92bf78b33b ("gpio: omap: use dynamic allocation of base")
but let's also fix that for devices where there is still
a mixture of static and dynamic allocation.
Fixes: 7b61212f2a ("gpiolib: Get rid of ARCH_NR_GPIOS")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: <christophe.leroy@csgroup.eu>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
While here update copyright and module author.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
While here update copyright and module author.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver's debugfs files have had a read operation since commit
2a9e27408e ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert platform_get_resource(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Drop kerneldoc annotation from regular comment to fix:
gpio-davinci.c:716: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove the map parameter from the struct regmap_irq_chip callback
handle_mask_sync() because it can be passed via the irq_drv_data
parameter instead. The gpio-104-dio-48e driver is the only consumer of
this callback and is thus updated accordingly.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com
Link: https://lore.kernel.org/r/1f44fb0fbcd3dccea3371215b00f1b9a956c1a12.1679323449.git.william.gray@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
A private data structure struct dio48e_gpio is introduced to facilitate
passage of the regmap and IRQ mask state for the device to the callback
dio48e_handle_mask_sync(). This is in preparation for the removal of the
handle_mask_sync() map parameter in a subsequent patch.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com
Link: https://lore.kernel.org/r/ca710d14a710fee44f7911f2a84b6a55570561ee.1679323449.git.william.gray@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
The changes for the hte/timestamp subsystem include the following:
- Add Tegra234 HTE provider and relevant DT bindings
- Update MAINTAINERS file for the HTE subsystem
-----BEGIN PGP SIGNATURE-----
iIgEABYIADAWIQT4slW2T0Q/rXAa29f4pUxhzZTZKAUCZErbLBIcZGlwZW5wQG52
aWRpYS5jb20ACgkQ+KVMYc2U2SiW0QEAt3bPgopjIMzaInOguZthR1pHCuKtyK7F
u4aJAyHv7tIA/jtsFJuFO4LmiwA/IsNits5l7F36oaB94/cQGuRH1M8E
=opcL
-----END PGP SIGNATURE-----
Merge tag 'for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pateldipen1984/linux
Pull hardware timestamp engine updates from Dipen Patel:
"The changes for the hte subsystem include:
- Add Tegra234 HTE provider and relevant DT bindings
- Update MAINTAINERS file for the HTE subsystem"
* tag 'for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pateldipen1984/linux:
hte: tegra-194: Use proper includes
hte: Use device_match_of_node()
hte: tegra-194: Fix off by one in tegra_hte_map_to_line_id()
hte: tegra: fix 'struct of_device_id' build error
hte: Use of_property_present() for testing DT property presence
gpio: tegra186: Add Tegra234 hte support
hte: handle nvidia,gpio-controller property
hte: Deprecate nvidia,slices property
hte: Add Tegra234 provider
hte: Re-phrase tegra API document
arm64: tegra: Add Tegra234 GTE nodes
dt-bindings: timestamp: Deprecate nvidia,slices property
dt-bindings: timestamp: Add Tegra234 support
MAINTAINERS: Add HTE/timestamp subsystem details
- Add support for Renesas RZ/G2L MTU3
- New Device Support
- Add support for Lenovo Yoga Book X90F to Intel CHT WC
- Add support for MAX5970 and MAX5978 to Simple MFD (I2C)
- Add support for Meteor Lake PCH-S LPSS PCI to Intel LPSS PCI
- Add support for AXP15060 PMIC to X-Powers PMIC collection
- Remove Device Support
- Remove support for Samsung 5M8751 and S5M8763 PMIC devices
- New Functionality
- Convert deprecated QCOM IRQ Chip to config registers
- Add support for 32-bit address spaces to Renesas SMUs
- Fix-ups
- Make use of APIs / MACROs designed to simplify and demystify
- Add / improve Device Tree bindings
- Memory saving struct layout optimisations
- Remove old / deprecated functionality
- Factor out unassigned register addresses from ranges
- Trivial: Spelling fixes, renames and coding style fixes
- Rid 'defined but not used' warnings
- Remove ineffective casts and pointer stubs
- Bug Fixes
- Fix incorrectly non-inverted mask/unmask IRQs on QCOM platforms
- Remove MODULE_*() helpers from non-tristate drivers
- Do not attempt to use out-of-range memory addresses associated with io_base
- Provide missing export helpers
- Fix remap bulk read optimisation fallout
- Fix memory leak issues in error paths
-----BEGIN PGP SIGNATURE-----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=EBtX
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Renesas RZ/G2L MTU3
New Device Support:
- Add support for Lenovo Yoga Book X90F to Intel CHT WC
- Add support for MAX5970 and MAX5978 to Simple MFD (I2C)
- Add support for Meteor Lake PCH-S LPSS PCI to Intel LPSS PCI
- Add support for AXP15060 PMIC to X-Powers PMIC collection
Remove Device Support:
- Remove support for Samsung 5M8751 and S5M8763 PMIC devices
New Functionality:
- Convert deprecated QCOM IRQ Chip to config registers
- Add support for 32-bit address spaces to Renesas SMUs
Fix-ups:
- Make use of APIs / MACROs designed to simplify and demystify
- Add / improve Device Tree bindings
- Memory saving struct layout optimisations
- Remove old / deprecated functionality
- Factor out unassigned register addresses from ranges
- Trivial: Spelling fixes, renames and coding style fixes
- Rid 'defined but not used' warnings
- Remove ineffective casts and pointer stubs
Bug Fixes:
- Fix incorrectly non-inverted mask/unmask IRQs on QCOM platforms
- Remove MODULE_*() helpers from non-tristate drivers
- Do not attempt to use out-of-range memory addresses associated with io_base
- Provide missing export helpers
- Fix remap bulk read optimisation fallout
- Fix memory leak issues in error paths"
* tag 'mfd-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (88 commits)
dt-bindings: mfd: ti,j721e-system-controller: Add SoC chip ID
leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver
dt-bindings: mfd: qcom,spmi-pmic: Document flash LED controller
dt-bindings: mfd: x-powers,axp152: Document the AXP15060 variant
mfd: axp20x: Add support for AXP15060 PMIC
dt-bindings: mfd: x-powers,axp152: Document the AXP313a variant
counter: rz-mtu3-cnt: Unlock on error in rz_mtu3_count_ceiling_write()
dt-bindings: mfd: dlg,da9063: Document voltage monitoring
dt-bindings: mfd: stm32: Remove unnecessary blank lines
dt-bindings: mfd: qcom,spmi-pmic: Use generic ADC node name in examples
dt-bindings: mfd: syscon: Add nuvoton,ma35d1-sys compatible
MAINTAINERS: Add entries for Renesas RZ/G2L MTU3a counter driver
counter: Add Renesas RZ/G2L MTU3a counter driver
Documentation: ABI: sysfs-bus-counter: add cascade_counts_enable and external_input_phase_clock_select
mfd: Add Renesas RZ/G2L MTU3a core driver
dt-bindings: timer: Document RZ/G2L MTU3a bindings
mfd: rsmu_i2c: Convert to i2c's .probe_new() again
mfd: intel-lpss: Add Intel Meteor Lake PCH-S LPSS PCI IDs
mfd: dln2: Fix memory leak in dln2_probe()
mfd: axp20x: Fix axp288 writable-ranges
...
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
To enable timestamp support for the Tegra234, has_gte variable needs
to be set true.
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patch implements the GPIO function of Intel USB-I2C/GPIO/SPI adapter
device named "La Jolla Cove Adapter" (LJCA). It communicate with LJCA
GPIO module with specific protocol through interfaces exported by LJCA USB
driver.
Signed-off-by: Ye Xiang <xiang.ye@intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230225140118.2037220-3-xiang.ye@intel.com
New drivers:
- add a driver for the Loongson GPIO controller
- add a driver for the fxl6408 I2C GPIO expander
- add a GPIO module containing code common for Intel Elkhart Lake and
Merrifield platforms
- add a driver for the Intel Elkhart Lake platform reusing the code from
the intel tangier library
GPIOLIB core:
- GPIO ACPI improvements
- simplify gpiochip_add_data_with_keys() fwnode handling
- cleanup header inclusions (remove unneeded ones, order the rest
alphabetically)
- remove duplicate code (reuse krealloc() instead of open-coding it, drop
a duplicated check in gpiod_find_and_request())
- reshuffle the code to remove unnecessary forward declarations
- coding style cleanups and improvements
- add a helper for accessing device fwnodes
- small updates in docs
Driver improvements:
- convert all remaining GPIO irqchip drivers to using immutable irqchips
- drop unnecessary of_match_ptr() macro expansions
- shrink the code in gpio-merrifield significantly by reusing the code from
gpio-tangier + minor tweaks to the driver code
- remove MODULE_LICENSE() from drivers that can only be built-in
- add device-tree support to gpio-loongson1
- use new regmap features in gpio-104-dio-48e and gpio-pcie-idio-24
- minor tweaks and fixes to gpio-xra1403, gpio-sim, gpio-tegra194, gpio-omap,
gpio-aspeed, gpio-raspberrypi-exp
- shrink code in gpio-ich and gpio-pxa
- Kconfig tweak for gpio-pmic-eic-sprd
-----BEGIN PGP SIGNATURE-----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=X+sP
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have some new drivers, significant refactoring of existing intel
platforms, lots of improvements all around, mass conversion to using
immutable irqchips by drivers that had not been converted individually
yet and some changes in the core library code.
Summary:
New drivers:
- add a driver for the Loongson GPIO controller
- add a driver for the fxl6408 I2C GPIO expander
- add a GPIO module containing code common for Intel Elkhart Lake and
Merrifield platforms
- add a driver for the Intel Elkhart Lake platform reusing the code
from the intel tangier library
GPIOLIB core:
- GPIO ACPI improvements
- simplify gpiochip_add_data_with_keys() fwnode handling
- cleanup header inclusions (remove unneeded ones, order the rest
alphabetically)
- remove duplicate code (reuse krealloc() instead of open-coding it,
drop a duplicated check in gpiod_find_and_request())
- reshuffle the code to remove unnecessary forward declarations
- coding style cleanups and improvements
- add a helper for accessing device fwnodes
- small updates in docs
Driver improvements:
- convert all remaining GPIO irqchip drivers to using immutable
irqchips
- drop unnecessary of_match_ptr() macro expansions
- shrink the code in gpio-merrifield significantly by reusing the
code from gpio-tangier + minor tweaks to the driver code
- remove MODULE_LICENSE() from drivers that can only be built-in
- add device-tree support to gpio-loongson1
- use new regmap features in gpio-104-dio-48e and gpio-pcie-idio-24
- minor tweaks and fixes to gpio-xra1403, gpio-sim, gpio-tegra194,
gpio-omap, gpio-aspeed, gpio-raspberrypi-exp
- shrink code in gpio-ich and gpio-pxa
- Kconfig tweak for gpio-pmic-eic-sprd"
* tag 'gpio-updates-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (99 commits)
gpio: gpiolib: Simplify gpiochip_add_data_with_key() fwnode
gpiolib: Add gpiochip_set_data() helper
gpiolib: Move gpiochip_get_data() higher in the code
gpiolib: Check array_info for NULL only once in gpiod_get_array()
gpiolib: Replace open coded krealloc()
gpiolib: acpi: Add a ignore wakeup quirk for Clevo NL5xNU
gpiolib: acpi: Move ACPI device NULL check to acpi_get_driver_gpio_data()
gpiolib: acpi: use the fwnode in acpi_gpiochip_find()
gpio: mm-lantiq: Fix typo in the newly added header filename
sh: mach-x3proto: Add missing #include <linux/gpio/driver.h>
powerpc/40x: Add missing select OF_GPIO_MM_GPIOCHIP
gpio: xlp: Convert to immutable irq_chip
gpio: xilinx: Convert to immutable irq_chip
gpio: xgs-iproc: Convert to immutable irq_chip
gpio: visconti: Convert to immutable irq_chip
gpio: tqmx86: Convert to immutable irq_chip
gpio: thunderx: Convert to immutable irq_chip
gpio: stmpe: Convert to immutable irq_chip
gpio: siox: Convert to immutable irq_chip
gpio: rda: Convert to immutable irq_chip
...
The code defaulting to the parents fwnode if no fwnode was assigned
is unnecessarily convoluted, probably due to refactoring. Simplify
it and make it more human-readable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The idi48 regmap can be used in an interrupt context by regmap-irq. To
prevent a deadlock, enable use_raw_spinlock for idi48_regmap_config.
Fixes: e28432a773 ("gpio: 104-idi-48: Migrate to the regmap-irq API")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The dio48e regmap can be used in an interrupt context by regmap-irq. To
prevent a deadlock, enable use_raw_spinlock for dio48e_regmap_config.
Fixes: 2f7e845f51 ("gpio: 104-dio-48e: Migrate to the regmap-irq API")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
- fix irq handling in gpio-davinci
- fix Kconfig dependencies for gpio-regmap
-----BEGIN PGP SIGNATURE-----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=ZM6C
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix irq handling in gpio-davinci
- fix Kconfig dependencies for gpio-regmap
* tag 'gpio-fixes-for-v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: davinci: Add irq chip flag to skip set wake
gpio: davinci: Do not clear the bank intr enable bit in save_context
gpio: GPIO_REGMAP: select REGMAP instead of depending on it
* Fixed suspend issue on Clevo NL5xNU
* Split a new Intel Tangier (library) driver for current and new platforms
* Introduced a new driver for Intel Elkhart Lake PSE GPIO (see also above)
* Contained a few fixes for the previous of_gpio.h cleanup
* Miscellaneous cleanups here and there
The following is an automated git shortlog grouped by driver:
elkhartlake:
- Introduce Intel Elkhart Lake PSE GPIO
gpiolib:
- acpi: Add a ignore wakeup quirk for Clevo NL5xNU
- acpi: Move ACPI device NULL check to acpi_get_driver_gpio_data()
- acpi: use the fwnode in acpi_gpiochip_find()
ich:
- Use devm_gpiochip_add_data() to simplify remove path
merrifield:
- Utilise temporary variable for struct device
- Use dev_err_probe()
- Adapt to Intel Tangier GPIO driver
mips:
- ar7: include linux/gpio/driver.h
mm-lantiq:
- Fix typo in the newly added header filename
powerpc/40x:
- Add missing select OF_GPIO_MM_GPIOCHIP
sh:
- mach-x3proto: Add missing #include <linux/gpio/driver.h>
tangier:
- Introduce Intel Tangier GPIO driver
-----BEGIN PGP SIGNATURE-----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=yI78
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.4-2
* Fixed suspend issue on Clevo NL5xNU
* Split a new Intel Tangier (library) driver for current and new platforms
* Introduced a new driver for Intel Elkhart Lake PSE GPIO (see also above)
* Contained a few fixes for the previous of_gpio.h cleanup
* Miscellaneous cleanups here and there
The following is an automated git shortlog grouped by driver:
elkhartlake:
- Introduce Intel Elkhart Lake PSE GPIO
gpiolib:
- acpi: Add a ignore wakeup quirk for Clevo NL5xNU
- acpi: Move ACPI device NULL check to acpi_get_driver_gpio_data()
- acpi: use the fwnode in acpi_gpiochip_find()
ich:
- Use devm_gpiochip_add_data() to simplify remove path
merrifield:
- Utilise temporary variable for struct device
- Use dev_err_probe()
- Adapt to Intel Tangier GPIO driver
mips:
- ar7: include linux/gpio/driver.h
mm-lantiq:
- Fix typo in the newly added header filename
powerpc/40x:
- Add missing select OF_GPIO_MM_GPIOCHIP
sh:
- mach-x3proto: Add missing #include <linux/gpio/driver.h>
tangier:
- Introduce Intel Tangier GPIO driver
There are too many 'data' parameters here and there.
For the better maintenance keep access GPIO device data
via getter and setter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Move gpiochip_get_data() higher in the code as a preparation
for further refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add the IRQCHIP_SKIP_SET_WAKE flag since there are no special IRQ Wake
bits that can be set to enable wakeup IRQ.
Fixes: 3d9edf09d4 ("[ARM] 4457/2: davinci: GPIO support")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The interrupt enable bits might be set if we want to use the GPIO as
wakeup source. Clearing this will mean disabling of interrupts in the GPIO
banks that we may want to wakeup from.
Thus remove the line that was clearing this bit from the driver's save
context function.
Cc: Devarsh Thakkar <devarsht@ti.com>
Fixes: 0651a73092 ("gpio: davinci: Add support for system suspend/resume PM")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some classes (i.e. gpio), want to know if they have been registered or
not, and poke around in the class's internal structures to try to figure
this out. Because this is not really a good idea, provide a function
for classes to call to try to figure this out.
Note, this is racy as the state of the class could change at any moment
in time after the call is made, but as usually a class only wants to
know if it has been registered yet or not, it should be fairly safe to
use, and is just as safe as the previous "poke at the class internals"
check was.
Move the gpiolib code to use this function as proof that it works
properly.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230331093318.82288-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpiod_get_array() has a long if-else-if branching where each of them
tests for the same variable to be not NULL. Instead, check for NULL
before even going to that flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
gpiod_get_array() does a new allocation in some cases, followed
by copying previously allocated placeholder for the descriptors.
Replace that with krealloc(__GFP_ZERO), since it was kzalloc()
originally.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
struct class should never be modified in a sysfs callback as there is
nothing in the structure to modify, and frankly, the structure is almost
never used in a sysfs callback, so mark it as constant to allow struct
class to be moved to read-only memory.
While we are touching all class sysfs callbacks also mark the attribute
as constant as it can not be modified. The bonding code still uses this
structure so it can not be removed from the function callbacks.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steve French <sfrench@samba.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-cifs@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230325084537.3622280-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xNU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
This patch is analoge to a very similar patch for NL5xRU, just the DMI
string changed.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's logical to check ACPI device for NULL inside
acpi_get_driver_gpio_data() instead of requiring that
in each caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
While trying to set up an SSDT override for a USB-2-I2C chip [0],
I realized that the function acpi_gpiochip_find() was using the parent
of the gpio_chip to do the ACPI matching.
This works fine on my Ice Lake laptop because AFAICT, the DSDT presents
the PCI device INT3455 as the "Device (GPI0)", but is in fact handled
by the pinctrl driver in Linux.
The pinctrl driver then creates a gpio_chip device. This means that the
gc->parent device in that case is the GPI0 device from ACPI and everything
works.
However, in the hid-cp2112 case, the parent is the USB device, and the
gpio_chip is directly under that USB device. Which means that in this case
gc->parent points at the USB device, and so we can not do an ACPI match
towards the GPIO device.
I think it is safe to resolve the ACPI matching through the fwnode
because when we call gpiochip_add_data(), the first thing it does is
setting a proper gc->fwnode: if it is not there, it borrows the fwnode
of the parent.
So in my Ice Lake case, gc->fwnode is the one from the parent, meaning
that the ACPI handle we will get is the one from the GPI0 in the DSDT
(the pincrtl one). And in the hid-cp2112 case, we get the actual
fwnode from the gpiochip we created in the HID device, making it working.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/linux-input/20230227140758.1575-1-kaehndan@gmail.com/T/#m592f18081ef3b95b618694a612ff864420c5aaf3 [0]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The header with legacy struct of_mmio_gpio_chip and accompanying
APIs is called legacy-of-mm-gpiochip.h. Remove repetitive '.h'
at the end.
Fixes: a99cc66807 ("gpiolib: split of_mm_gpio_chip out of linux/of_gpio.h")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Convert the driver to immutable irq-chip with a bit of
intuition.
In this case the driver uses .mask_ack() and .unmask()
and since I have a vague idea about the semantics of
.mask_ack() I added .irq_enable() to the existing .irq_disable()
and called into the gpiolib core from those callbacks
instead of mask/unmask.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
The driver is for a hierarchical chip so some extra care
needs to be taken to introduce two new callbacks.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Whereas in most cases we put the gpiochip_[enable|disable]_irq()
calls in the .irq_mask() and .irq_unmask() callbacks, here
we need to put them in the .irq_enable() and .irq_disable()
callbacks, as this driver uses both .irq_mask() and
.irq_mask_ack().
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
In this case I had to figure out a way to get to the
struct gpio_chip that would work even when the irq_chip
is not part of the driver state container. I did this by
just doing what most other GPIO drivers do and pass
the state struct as data to devm_gpiochip_add_data()
and rewrite accordingly.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This patch introduces and allocates ls1x_gpio_chip struct containing
gpio_chip and reg_base to avoid global gpio_reg_base.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use SPDX-License-Identifier instead of the license text.
The current author name is unofficial, change it to my real name.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The 104-DIO-48E lacks an IRQ status register. Rather than use the Clear
Interrupt register as the status register, set the no_status flag to
true and thus avoid such a hack.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
clang with W=1 reports
drivers/gpio/gpio-pxa.c:174:19: error: unused function
'gpio_is_pxa_type' [-Werror,-Wunused-function]
static inline int gpio_is_pxa_type(int type)
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add minimal driver for Fairchild FXL6408 8-bit I2C-controlled GPIO expander
using the generic regmap based GPIO driver (GPIO_REGMAP).
The driver implements setting the GPIO direction, reading inputs
and writing outputs.
In addition to that the FXL6408 has the following functionalities:
- allows to monitor input ports for data transitions with an interrupt pin
- all inputs can be configured with pull-up or pull-down resistors
Datasheet: https://www.onsemi.com/download/data-sheet/pdf/fxl6408-d.pdf
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Co-developed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[Bartosz: order includes alphabetically]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The SPDX License Identifier line renders the GPL boilerplate text
superfluous, so let's remove it.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
IRQ framework provides special type and getter to transform
the Linux IRQ to the hardware pin. Use that type and getter
function instead of direct access.
While at it, amend an indentation in a couple of places.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The gpiod_find_by_fwnode() already checks for NULL and returns
correct error code in case fwnode is invalid. Drop the respective
check and assignment in the gpiod_find_and_request().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The functions that operates on the same device object would
have the same namespace for better code understanding and
maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The devprop prefix in the devprop_gpiochip_set_names() adds confusion.
Get rid of it.
Note we have more than one function in the same module that handles
one or more device properties. This change will unify the naming schema
for all of them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/gpio/gpio-raspberrypi-exp.c:237:34: error: ‘rpi_exp_gpio_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/gpio/gpio-xra1403.c:198:34: error: ‘xra1403_spi_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-sama5d2-piobu.c:230:34: error: ‘sama5d2_piobu_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-sifive.c:263:34: error: ‘sifive_gpio_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-visconti.c:187:34: error: ‘visconti_gpio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-rcar.c:435:34: error: ‘gpio_rcar_of_table’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-altera.c:324:34: error: ‘altera_gpio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-ftgpio010.c:336:34: error: ‘ftgpio_gpio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Run the steps to deactivate device in the reserved order to what
it has been done in gpio_sim_device_activate_unlocked().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove .owner field if calls are used which set it automatically.
./drivers/gpio/gpio-loongson-64bit.c:225:3-8: No need to set .owner here. The core will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4450
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
This driver require some special care: .irq_ack() was copied
from dummy_irq_chip where it was defined as noop. This only
makes sense if using handle_edge_irq() that will unconditionally
call .irq_ack() to avoid a crash, but this driver is not ever
using handle_edge_irq() so just avoid assigning .irq_ack().
A separate chip had to be created for the non-wakeup instance.
Cc: Marc Zyngier <maz@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The OMAP1 at one point was using static irqs but that time is gone,
OMAP1 uses sparse irqs like all other multiplatform targets so this
static allocation of descriptors should just go.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
This conversion follows the pattern of the gpio-ixp4xx
hierarchical GPIO interrupt driver.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Tested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
The IRQ chip was unnamed which seems unwise, so we just
assign the name "HISI-GPIO".
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver was implemented in a way that made the irqchip optional, if a
irq was not present in the device tree. However, all of the device trees
have always had an irq, so the optional-ness has never been used.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the driver to immutable irq-chip with a bit of
intuition.
Cc: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is nothing specific about gpio_bus_match(), so we may
simply move it to the top of the file and get rid of forward
declaration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
GPIO device's fwnode should be accessed via dev_fwnode().
Make sure that gpiochip_setup_dev() follows that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* Remove some of the legacy APIs that are not used anymore
* Clean up headers in the GPIO library and drivers
The following is an automated git shortlog grouped by driver:
aggregator:
- Add missing header(s)
ARM:
- s3c64xx: Use the right include
- orion/gpio: Use the right include
gpiolib:
- Clean up headers
- Group forward declarations in consumer.h
- Deduplicate forward declarations in consumer.h
- Drop unused forward declaration from driver.h
- split of_mm_gpio_chip out of linux/of_gpio.h
- split linux/gpio/driver.h out of linux/gpio.h
- remove legacy gpio_export()
- remove gpio_set_debounce()
- remove asm-generic/gpio.h
- coldfire: remove custom asm/gpio.h
- remove empty asm/gpio.h files
- Make the legacy <linux/gpio.h> consumer-only
hte:
- tegra-194: Use proper includes
reg:
- Add missing header(s)
regmap:
- Add missing header(s)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAmQHHfQACgkQb7wzTHR8
rCim7A//Rar7oFB82nHriufTxWV0CjQzu2xJw3p0liIyA7iWydEVpparfM7Mqv0z
3Z/03vG1H12M8wQ4jFyPfxcT1UPLaQSRCBl7omEWupFHvyUEIz+/Xxt9BY9RAKno
ZK2Ty0YR00MlXZOPosd+Hv9jwWJMw2mrwQy4mStn8jCCeblF675ad6dfzVuPlsaY
kKdZslUT48NcCQZolQaz6V0ygy6O2JUabkuh9uJSYG0/ZN4UZzCYtvhfcvXgVTNJ
IQz2Fl4g1mR/r1JU8upVW0WR78LEKIcyUHD+ARD4oCXPdjSTp8k25UExyn121k7L
qxSAIlJKEg0s0/0hwVOsuyhnYrJXXgivkOGXbnDp27Su8pGejHS0WGn4LMxTa2SV
A1OaxrfxAy57lBv3j4bfEWTxQB1Nxo22EA2ejm5Jd0JxB6cQ2NlJqlwE+StYYSkg
8sFp/rim/mcNO3r3BLa/WliOp+TWtVFAsVCSf9uxVQmtUBnoHte+GGiyVZZuSNyS
fS8F5xURJQwempT1T0LUr6Ex5s4okJc9D+wEpatK9IpSszBgFOdb/U335+noRChF
pLkQsAOZa5GTGQbHYkAUBJY90gd8KN+63sJNBgcpo1HxifCrSfjrSw8T3tJhUAH/
ppI1R3KLhFQzl8jB/3EDN+eNWvtMPqAc19JEsfOuG9ytGBj/wX0=
=DBx5
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.4-1
* Remove some of the legacy APIs that are not used anymore
* Clean up headers in the GPIO library and drivers
The following is an automated git shortlog grouped by driver:
aggregator:
- Add missing header(s)
ARM:
- s3c64xx: Use the right include
- orion/gpio: Use the right include
gpiolib:
- Clean up headers
- Group forward declarations in consumer.h
- Deduplicate forward declarations in consumer.h
- Drop unused forward declaration from driver.h
- split of_mm_gpio_chip out of linux/of_gpio.h
- split linux/gpio/driver.h out of linux/gpio.h
- remove legacy gpio_export()
- remove gpio_set_debounce()
- remove asm-generic/gpio.h
- coldfire: remove custom asm/gpio.h
- remove empty asm/gpio.h files
- Make the legacy <linux/gpio.h> consumer-only
hte:
- tegra-194: Use proper includes
reg:
- Add missing header(s)
regmap:
- Add missing header(s)
