VSC8541 phys need a special reset sequence, which the driver doesn't
currentlny support. As a result enabling the reset via GPIO essentially
guarnteees that the device won't work correctly. We've been relying on
bootloaders to reset the device for years, with this revert we'll go
back to doing so until we can sort out how to get the reset sequence
into the kernel.
This reverts commit a0fa9d7270.
Fixes: a0fa9d7270 ("dts: phy: add GPIO number and active state used for phy reset")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The GEMGXL_RST line on HiFive Unleashed is pulled low and is
using GPIO number 12. Add these reset-gpio details to dt-node
using which the linux phylib can reset the phy.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
HiFive unleashed A00 board has VSC8541-01 ethernet phy, this device is
identified as a Revision B device as described in device identification
registers. In order to use this phy in the unmanaged mode, it requires
a specific reset sequence of logical 0-1-0-1 transition on the NRESET pin
as documented here [1].
Currently, the bootloader (fsbl or u-boot-spl) takes care of the phy reset.
If due to some reason the phy device hasn't received the reset by the prior
stages before the linux macb driver comes into the picture, the MACB mii
bus gets probed but the mdio scan fails and is not even able to read the
phy ID registers. It gives an error message:
"libphy: MACB_mii_bus: probed
mdio_bus 10090000.ethernet-ffffffff: MDIO device at address 0 is missing."
Thus adding the device OUI (Organizationally Unique Identifier) to the phy
device node helps to probe the phy device.
[1]: VSC8541-01 datasheet:
https://www.mouser.com/ds/2/523/Microsemi_VSC8541-01_Datasheet_10496_V40-1148034.pdf
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Do not track all compressed Image and loader.bin.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Let's remove all files under riscv boot dir by using archclean rule.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The Kendryte K210 SoC CLINT is compatible with Sifive clint v0
(sifive,clint0). Fix the Kendryte K210 device tree clint entry to be
inline with the sifive timer definition documented in
Documentation/devicetree/bindings/timer/sifive,clint.yaml.
The device tree clint entry is renamed similarly to u-boot device tree
definition to improve compatibility with u-boot defined device tree.
To ensure correct initialization, the interrup-cells attribute is added
and the interrupt-extended attribute definition fixed.
This fixes boot failures with Kendryte K210 SoC boards.
Note that the clock referenced is kept as K210_CLK_ACLK, which does not
necessarilly match the clint MTIME increment rate. This however does not
seem to cause any problem for now.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Add ARCH_HAS_KCOV and HAVE_GCC_PLUGINS to the riscv Kconfig.
Also disable instrumentation of some early boot code and vdso.
Boot-tested on QEMU's riscv64 virt machine.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The K210's bootloader does not provide a device tree. Give the ability
to providea builtin one with the SOC_KENDRYTE_K210_BUILTIN_DTB option.
If selected, this option result in the definition of a builtin DTB
entry in the k210 sysctl driver.
If defined, the builtin DTB entry points to the default k210.dts device
tree file and is keyed with the vendor ID 0x4B5, the arch ID
0xE59889E6A5A04149 ("Canaan AI" in UTF-8 coded Chinese) and the impl ID
0x4D41495832303030 ("MAIX200"). These values are reported by the SiPEED
MAIXDUINO board, the SiPEED MAIX Go board and the SiPEED Dan Dock board.
[Thanks to Damien for the K210 IDs]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This tag contains the patches I'd like to target for 5.7. It has a handful of
new features:
* Partial support for the Kendryte K210. There are still a few outstanding
issues that I have patches for, but I don't actually have a board to test
them so they're not included yet.
* SBI v0.2 support.
* Fixes to support for building with LLVM-based toolchains. The resulting
images are known not to boot yet.
This builds and boots for me. There is one merge conflict, it's just a Kconfig
merge issue. I can publish a resolved branch if you'd like.
I don't anticipate a part two, but I'll probably have something early in the
RCs to finish up the K210 support.
-----BEGIN PGP SIGNATURE-----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=P1DO
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains a handful of new features:
- Partial support for the Kendryte K210.
There are still a few outstanding issues that I have patches for,
but I don't actually have a board to test them so they're not
included yet.
- SBI v0.2 support.
- Fixes to support for building with LLVM-based toolchains. The
resulting images are known not to boot yet.
I don't anticipate a part two, but I'll probably have something early
in the RCs to finish up the K210 support"
* tag 'riscv-for-linus-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (38 commits)
riscv: create a loader.bin boot image for Kendryte SoC
riscv: Kendryte K210 default config
riscv: Add Kendryte K210 device tree
riscv: Select required drivers for Kendryte SOC
riscv: Add Kendryte K210 SoC support
riscv: Add SOC early init support
riscv: Unaligned load/store handling for M_MODE
RISC-V: Support cpu hotplug
RISC-V: Add supported for ordered booting method using HSM
RISC-V: Add SBI HSM extension definitions
RISC-V: Export SBI error to linux error mapping function
RISC-V: Add cpu_ops and modify default booting method
RISC-V: Move relocate and few other functions out of __init
RISC-V: Implement new SBI v0.2 extensions
RISC-V: Introduce a new config for SBI v0.1
RISC-V: Add SBI v0.2 extension definitions
RISC-V: Add basic support for SBI v0.2
RISC-V: Mark existing SBI as 0.1 SBI.
riscv: Use macro definition instead of magic number
riscv: Add support to dump the kernel page tables
...
Create the loader.bin bootable image file that can be loaded into
Kendryte K210 based boards using the kflash.py tool with the command:
kflash.py/kflash.py -t arch/riscv/boot/loader.bin
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Add a generic device tree for Kendryte K210 SoC based boards. This is
for now a very simple device tree describing the core elements of the
SoC. This is suitable (and tested) for the Kendryte KD233 development
board, the Sipeed MAIX M1 Dan Dock board and the Sipeed MAIXDUINO board.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Add the ability to reboot the HiFive Unleashed board via GPIO.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tell git to not track the compiled boot/loader and boot/loader.lds
files.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The Makefile addition for the flat image loader missed an obj prefix.
For most parallel builds this worked out fine, but with -j1 the dependency
wasn't fulfilled and thus fails:
arch/riscv/boot/loader.S: Assembler messages:
arch/riscv/boot/loader.S:7: Error: file not found: arch/riscv/boot/Image
Fixes: 405fe7aa0d ("riscv: provide a flat image loader")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This allows just loading the kernel at a pre-set address without
qemu going bonkers trying to map the ELF file.
Contains a contribution from Aurabindo Jayamohanan to reuse the
PAGE_OFFSET definition.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: fixed checkpatch issue; minor commit
message fix]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Add PDMA support to (arch/riscv/boot/dts/sifive/fu540-c000.dtsi)
Signed-off-by: Green Wan <green.wan@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Currently, there is only support for .gz compression type
for generating kernel Image.
Add support for other compression methods(lzma, lz4, lzo, bzip2)
that helps in generating a even smaller kernel image. Image.gz
will still be the default compressed image.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Add a default "stdout-path" to the kernel DTS file, as is present in many
of the board DTS files elsewhere in the kernel tree. With this line
present, earlyconsole can be enabled by simply passing "earlycon" on the
kernel command line. No specific device details are necessary, since the
kernel will use the stdout-path as the default.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The "clock-frequency" property of cpu nodes isn't required. Drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
U-Boot expects this alias to be in place in order to fix up the mac
address of the ethernet node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
On FU540-based systems, the "timebase-frequency" (RTCCLK) is sourced
from an external crystal located on the PCB. Thus the
timebase-frequency DT property should be defined by the board that
uses the SoC, not the SoC itself. Drop the superfluous
timebase-frequency property from the SoC DT data. (It's already
present in the board DT data.)
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
DT node for SiFive FU540-C000 GEMGXL Ethernet controller driver added
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Cc: Andrew Lunn <andrew@lunn.ch>
[paul.walmsley@sifive.com: changed "phy1" to "phy0" at Andrew Lunn's
suggestion]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
As per the convention for any SOC device with external connection,
define only device DT node in SOC DTSi file with status = "disabled"
and enable device in Board DTS file with status = "okay"
Reported-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Add initial board data for the SiFive HiFive Unleashed A00.
Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Add initial support for the SiFive FU540-C000 SoC. This is a 28nm SoC
based around the SiFive U54-MC core complex and a TileLink
interconnect.
This file is expected to grow as more device drivers are added to the
kernel.
This patch includes a fix to the QSPI memory map due to a
documentation bug, found by ShihPo Hung <shihpo.hung@sifive.com>, adds
entries for the I2C controller, and merges all DT changes that
formerly were made dynamically by the riscv-pk BBL proxy kernel.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: ShihPo Hung <shihpo.hung@sifive.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Similar to ARM64, add support for building DTB files from DT source
data for RISC-V boards.
This patch starts with the infrastructure needed for SiFive boards.
Boards from other vendors would add support here in a similar form.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
This patch extends Linux RISC-V build system to build and install:
Image - Flat uncompressed kernel image
Image.gz - Flat and GZip compressed kernel image
Quiet a few bootloaders (such as Uboot, UEFI, etc) are capable of
booting flat and compressed kernel images. In case of Uboot, booting
Image or Image.gz is achieved using bootm command.
The flat and uncompressed kernel image (i.e. Image) is very useful
in pre-silicon developent and testing because we can create back-door
HEX files for RAM on FPGAs from Image.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
