Add bindings for ACLK_CPU, HCLK_CPU, PCLK_CPU, ACLK_PERI, HCLK_PERI, PCLK_PERI.
We need this to init it's rate at boot time.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We need to get the accurate 533.25MHz for the DP display.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
control. While reading that clock is done the normal way from the
registers, setting it always requires some sort of special handling
to let the system survive this addition.
As the commit message explains, there are currently 3 handling-types
known. General SRAM-based code on rk3288 and before (which is waiting
essentially for the PIE support that is currently being worked on),
SCPI-based clk setting on the rk3368 through a coprocessor, which we
might support once the support for legacy scpi-variants has matured
and now on the rk3399 (and probably later) using a dcf controller that
is controlled from the arm-trusted-firmware and gets accessed through
firmware calls from the kernel. This is the variant we currently
support, but the clock type is made to support the other variants in
the future as well.
Apart from that slightly bigger chunk, we have a mix of PLL rates,
clock-ids and flags mainly for the rk3399.
And interestingly an iomap fix for the legacy gate driver, where I
hopefully could deter the submitter from actually using that in any
new works.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXzrz5AAoJEPOmecmc0R2B0NMH/0SGrQnrUsaq0cvjZPaq8jTD
nJDVIRw099HNM3QZCfy+FZbSsnmex93clX+Fn4UdehplrCZ8ExX1wpPkMwvFcPJF
M34YyFXx5MU9OmDsJXd1UlGRD/mH0L6hKnmfBQiPbK33ObXbr7LCC1L3go+oYABN
eHaOzO1KIcdoCQd6RlVAQHCsiDy8akUJ68P2uACHZ7VVgvGw2f3NdJhOKTD5lCuf
WH/MRo9X9bPDGHpFJIX+mZzZgYsMqUjyF/mYU/VMoH70w+YZTnfcbrYpJ0VkgBYd
aQF2B9VXhed9EQG3Gfu+jgsWoWLed9AJf83UP6eMsPTPLNQBqgzoDZwylbY1Szk=
=LjDG
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
The biggest addition is probably the special clock-type for ddr clock
control. While reading that clock is done the normal way from the
registers, setting it always requires some sort of special handling
to let the system survive this addition.
As the commit message explains, there are currently 3 handling-types
known. General SRAM-based code on rk3288 and before (which is waiting
essentially for the PIE support that is currently being worked on),
SCPI-based clk setting on the rk3368 through a coprocessor, which we
might support once the support for legacy scpi-variants has matured
and now on the rk3399 (and probably later) using a dcf controller that
is controlled from the arm-trusted-firmware and gets accessed through
firmware calls from the kernel. This is the variant we currently
support, but the clock type is made to support the other variants in
the future as well.
Apart from that slightly bigger chunk, we have a mix of PLL rates,
clock-ids and flags mainly for the rk3399.
And interestingly an iomap fix for the legacy gate driver, where I
hopefully could deter the submitter from actually using that in any
new works.
* tag 'v4.9-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: use the dclk_vop_frac clock ids on rk3399
clk: rockchip: drop CLK_SET_RATE_PARENT from rk3399 fractional dividers
clk: rockchip: add 2016M to big cpu clk rate table on rk3399
clk: rockchip: add rk3399 ddr clock support
clk: rockchip: add dclk_vop_frac ids for rk3399 vop
clk: rockchip: add new clock-type for the ddrclk
soc: rockchip: add header for ddr rate SIP interface
clk: rockchip: add SCLK_DDRC id for rk3399 ddrc
clk: rockchip: handle of_iomap failures in legacy clock driver
clk: rockchip: mark rk3399 hdcp_noc and vio_noc as critical
clk: rockchip: use general clock flag when registering pll
clk: rockchip: delete the CLK_IGNORE_UNUSED from aclk_pcie on rk3399
clk: rockchip: add 65MHz and 106.5MHz rates to rk3399 plls used for HDMI
Export the dclk_vop_frac out, so we can set the dclk_vop as the
child of dclk_vop_frac, and then we can start to take use of
the fractional dividers.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently the fractional divider clock time can't handle the
CLK_SET_RATE_PARENT flag. This is because, unlike normal dividers,
there is no clk_divider_bestdiv() function to try speeding up the parent
to see if it helps things.
Eventually someone could try to figure out how to make fractional
dividers able to use CLK_SET_RATE_PARENT, but until they do let's not
confuse the common clock framework (and anyone using it) by setting the
flag.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We would prefer the 2016M as 2.0G than 1992M which seems odd, adding
it to big cpu clk rate table then we can set 2016M in dts.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add ddrc clock setting, so we can do ddr frequency
scaling on rk3399 platform in future.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Changing the rate of the DDR clock needs special care, as the DDR
is of course in use and will react badly if the rate changes under it.
Over time different approaches to handle that were used.
Past SoCs like the rk3288 and before would store some code in SRAM
while the rk3368 used a SCPI variant and let a coprocessor handle that.
New rockchip platforms like the rk3399 have a dcf controller to do ddr
frequency scaling, and support for this controller will be implemented
in the arm-trusted-firmware.
This new clock-type should over time handle all these methods for
handling DDR rate changes, but right now it will concentrate on the
SIP interface used to talk to ARM trusted firmware.
The SIP interface counterpart was merged from pull-request #684 [0]
into the upstream arm-trusted-firmware codebase.
[0] https://github.com/ARM-software/arm-trusted-firmware/pull/684
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We don't have code to handle any of the noc clocks in rk3399 and they're
all just listed as critical clocks. Let's do the same for
aclk_emmc_noc.
Without this clock being marked as critical we have problems around
suspend/resume after commit 20c389e656 ("clk: rockchip: fix incorrect
aclk_emmc source gate bits on rk3399"). Before that change we were
presumably not actually gating any of these clocks because we were
setting the wrong gate.
Fixes: 20c389e656 ("clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Sorry to refer incorrect clock diagram, we double check it that the bits
configuration of the Xpll_aclk_perihp_src need to be fixed:
bit 1 - shows aclk_perihp_cpll_src_en
bit 0 - shows aclk_perihp_gpll_src_en
Through the testing that plug/unplug the USB ethernet cable on the RK3399 kevin board.
1. the hclk_host0 and hclk_host1 are endpoint clocks:
cpll --> G5[1] --> aclk_perihp_cpll_src --\ |--> hclk_host0
| --> ... ---> |
gpll --> G5[0] --> aclk_perihp_gpll_src --/ |--> hclk_host1
2. there is no clock below the cpll_aclk_perihp_src,
and the hclk_hostX are below the gpll_aclk_perihp_src:
pll_cpll 1 1 800000000 0 0
cpll 7 19 800000000 0 0
cpll_aclk_perihp_src 0 0 800000000 0 0
...
pll_gpll 1 1 594000000 0 0
gpll 10 10 594000000 0 0
gpll_aclk_perihp_src 2 2 594000000 0 0
hclk_perihp 5 5 74250000 0 0
hclk_host1_arb 2 2 74250000 0 0
hclk_host1 2 2 74250000 0 0
hclk_host0_arb 2 2 74250000 0 0
hclk_host0 2 2 74250000 0 0
3. by default, G5[0] and G5[1] are enabled:
localhost ~ # mem r 0xff760314
0x000003e0
4. close the G5[1] (aclk_perihp_cpll_src), and plug/unplug USB ethernet cable,
the DUT still works well:
localhost ~ # mem w 0xff760314 0xffff03e2
localhost ~ # mem r 0xff760314
0x000003e2
plug/unplug, the work statue is ok
5. close the G5[0] (aclk_perihp_gpll_src), , and plug/unplug USB ethernet cable,
the DUT will be crashed:
localhost ~ # mem w 0xff760314 0xffff03e1
localhost ~ # mem r 0xff760314
0x000003e1
plug/unplug, the DUT is crashed
Summary:
bit 1 - shows aclk_perihp_cpll_src_en
bit 0 - shows aclk_perihp_gpll_src_en
Fixes: 3bd14ae9da ("clk: rockchip: fix incorrect parent for rk3399's {c,g}pll_aclk_perihp_src")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
[here the clock-documentation in the manual was actually stating the wrong
bits and thus only Xing's testing above revealed the issue]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Dues to incorrect diagram, we need to fix incorrect bits for
(c/g)pll_aclk_emmc_src:
cpll_aclk_emmc_src --> G6[13]
gpll_aclk_emmc_src --> G6[12]
Fixes: 115510053e ("clk: rockchip: add clock controller for the RK3399")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The aclk_vio_noc should be put into critical list, as the interconnect
is not handled right now, but is required by VOP.
And the Type-C DP need these clocks: aclk_hdcp_noc, hclk_hdcp_noc,
pclk_hdcp_noc. Mark them as critical to avoid someone close them.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the general flags the pll list already contains to the clock init,
so that needed clock flags can be used for plls.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
We need to add more clocks for supporting more display resolution
for HDMI.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3228 clockids and a small fix for the not yet used spdif to
displayport clock on the rk3399.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXdbFVAAoJEPOmecmc0R2B2fEH/1Gm80XZsrXPrr0kZ2cO8Zcg
qUpOPJgZvEWJdG1EGzU34VAEAZP0y8sth46iypL+TP3UVf6Z9acZF2eeAbEvzdVY
pM6qb0eNLdrcV+aaKhAScxjEwg5kdLxc/kuwOr9XsZwE4Wqvsbmldw5O8qEU8DAP
fxdhi854hlanCVmTCfdjEpeRqv9JCejU27KttldqBC/0CwGaQwp0cUcp6Ggpv9pF
deHR5BGj2cwnPR2JmNsZ9U85kgf9/7jd4PD4UXNRG/ApuwpIb0/1ulr4YquqAcDW
OpdO6at9QmZItYS6byKNoAPKWoGXjmHYnjlENODQsCXoa6K8HkmDnxBtli6Iczw=
=6ikd
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
Placeholder for the rk3399 watchdog pclk, some newly exported
rk3228 clockids and a small fix for the not yet used spdif to
displayport clock on the rk3399.
* tag 'v4.8-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix incorrect rk3399 spdif-DPTX divider bits
clk: rockchip: export rk3228 MAC clocks
clk: rockchip: rename rk3228 sclk_macphy_50m to sclk_mac_extclk
clk: rockchip: export rk3228 audio clocks
clk: rockchip: include rk3228 downstream muxes into fractional dividers
clk: rockchip: fix incorrect rk3228 clock registers
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
clk: rockchip: add a dummy clock for the watchdog pclk on rk3399
The CLKSEL_CON32 bit_0 is controlled for spdif_8ch, not spdif_rec_dptx,
it should be bit_8, let's fix it.
Fixes: 115510053e ("clk: rockchip: add clock controller for the RK3399")
Reported-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch exports related MAC clocks for dts reference.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The sclk_macphy_50m is confusing, the sclk_mac_extclk describes
a external clock clearly.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch exports related i2s/spdif clocks for dts reference.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
During the initial conversion to the newly introduced combined fractional
dividers+muxes the rk3228 clocks were left out, so convert them now.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Due to copy and paste carelessly, RK3288_CLKxxx references are incorrect,
we need to fix them.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We should call iounmap to relase reg_base since it's not going
to be used any more if failing to init clk.
This was missing on the newly added rk3399 clock tree.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Like rk3288, the pclk supplying the watchdog is controlled via the
SGRF register area. Additionally the SGRF isn't even writable in
every boot mode.
But still the clock control is available and in the future someone
might want to use it. Therefore define a simple clock for the time
being so that the watchdog driver can read its rate.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It maybe due to a copy-paste error the error handing should be
cclk not clk when checking if the cpuclk registration succeeded.
Reported-by: Lin Huang <lin.huang@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This reverts commit 7a03fe6f48 ("clk: rockchip: reset init state
before mmc card initialization").
Though not totally obvious from the commit message nor from the source
code, that commit appears to be trying to reset the "_drv" MMC clocks to
90 degrees (note that the "_sample" MMC clocks have a shift of 0 so are
not touched).
The major problem here is that it doesn't properly reset things. The
phase is a two bit field and the commit only touches one of the two
bits. Thus the commit had the following affect:
- phase 0 => phase 90
- phase 90 => phase 90
- phase 180 => phase 270
- phase 270 => phase 270
Things get even weirder if you happen to have a bootloader that was
actually using delay elements (should be no reason to, but you never
know), since those are additional bits that weren't touched by the
original patch.
This is unlikely to be what we actually want. Checking on rk3288-veyron
devices, I can see that the bootloader leaves these clocks as:
- emmc: phase 180
- sdmmc: phase 90
- sdio0: phase 90
Thus on rk3288-veyron devices the commit we're reverting had the effect
of changing the eMMC clock to phase 270. This probably explains the
scattered reports I've heard of eMMC devices not working on some veyron
devices when using the upstream kernel.
The original commit was presumably made because previously the kernel
didn't touch the "_drv" phase at all and relied on whatever value was
there when the kernel started. If someone was using a bootloader that
touched the "_drv" phase then, indeed, we should have code in the kernel
to fix that. ...and also, to get ideal timings, we should also have the
kernel change the phase depending on the speed mode. In fact, that's
the subject of a recent patch I posted at
<https://patchwork.kernel.org/patch/9075141/>.
Ideally, we should take both the patch posted to dw_mmc and this
revert. Since those will likely go through different trees, here I
describe behavior with the combos:
1. Just this revert: likely will fix rk3288-veyron eMMC on some devices
+ other cases; might break someone with a strange bootloader that
sets the phase to 0 or one that uses delay elements (pretty
unpredicable what would happen in that case).
2. Just dw_mmc patch: fixes everyone. Effectly the dw_mmc patch will
totally override the broken patch and fix everything.
3. Both patches: fixes everyone. Once dw_mmc is initting properly then
any defaults from the clock code doesn't mattery.
Fixes: 7a03fe6f48 ("clk: rockchip: reset init state before mmc card initialization")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
[emmc and sdmmc still work on all current boards in mainline after this
revert, so they should take precedence over any out-of-tree board that
will hopefully again get fixed with the better upcoming dw_mmc change.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There was a typo, swapping 'c' <--> 'g'.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We never want to kill the GIC.
Noticed when making other clock fixups, and seeing the newly-constructed
clock tree try to disable cpll, where we had this parent structure:
aclk_gic <------\
|--- aclk_gic_pre <-- cpll <-- pll_cpll
aclk_gic_noc <--/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The flags element of clk_init_data was never initialized for mmc-
phase-clocks resulting in the element containing a random value
and thus possibly enabling unwanted clock flags.
Fixes: 89bf26cbc1 ("clk: rockchip: Add support for the mmc clock phases using the framework")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull rockchip clk updates from Heiko Stuebner:
Another small rk3399 fixup as well as simplifications around
our handling of the General-Register-Files syscon.
* tag 'v4.7-rockchip-clk4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: drop old_rate calculation on pll rate changes
clk: rockchip: simplify GRF handling in pll clocks
clk: rockchip: lookup General Register Files in rockchip_clk_init
clk: rockchip: fix the rk3399 sdmmc sample / drv name
Previously when everything happened in the set_rate callbacks itself we
needed the old_rate value for the possible rate rollback, so that made
it easy to also use it in the debug output.
Now with the param-handling being done in separate functions, reading and
recalculating the current pll rate only to use it in a debug message that
won't get displayed in regular cases anyway is quite a waste.
Therefore drop that value from the debug output. In the worst case that
previous rate will have been displayed on the rate change before.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the previous commit, the clock drivers now know at init time if the
GRF regmap is available. That means if it isn't available then, it also
won't become available later and we can therefore switch PLLs, that need
the GRF for the lock-status, to read-only mode - similar behaviour as the
aborting of rate changes we did before.
This saves some conditionals on every rate change and we can also drop
the rockchip_clk_get_grf function completely.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In the distant past syscons were initialized pretty late and weren't
available at the time the clock init ran. As the GRF is mainly needed
for PLL lock-status checking, we had this lazy init that tried to grab
the syscon on PLL rate changes and denied these changes if it was not
available.
These days syscons are available very early and recent addition to
rockchip clocks, like the PLL clk_init actually also rely on them
being available at that time, so there is no need to keep that lazy
init around, as it will also result in some more simplifications in
other parts of the clock-code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3399 clock table had a simple typo in it, calling the SDMMC sample
and drive clocks by the wrong name. Fix this minor typo.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXIogdAAoJEPOmecmc0R2BmToH/0D0OdIU6WuAxlfhz0cluLm8
bzZ5hwA4ZVv73QorGFIXA2B6Aq/GKV+2HcoqSKT+gMspgpi1o4TdPcknIEpVDQ9r
vWUXW0VBN04dGNlk0J9N2XAPWokdkHRuFentf/EZATrAPWSwIMsri7QiF2hw3MiA
yWKQKmJki8IJC6JPtisj9HORKyqAeoyxOn8vPHA5TUOYAD4YIbcY3BJ7xApJ2W5i
ikJAVu4agjMrHRJ1ALyI0m6ZeczbtMvpigl6fvMTyt/27BhHou2AhrOqSr5Wg04t
Sh++L/wY0ZHIo5HFw9voAu6EVb6NachxKvnG8cCvgV8BGofsrArIdXmJFEwQWOk=
=yN9B
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-clk3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk updates from Heiko Stuebner:
A spelling fix and a bunch of rk3399 clock fixes.
* tag 'v4.7-rockchip-clk3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix the rk3399 cifout clock
clk: rockchip: drop unnecessary CLK_IGNORE_UNUSED flags from rk3399
clk: rockchip: add some frequencies on the rk3399 PLL table
clk: rockchip: assign more necessary rk3399 clock ids
clk: rockchip: export some necessary rk3399 clock ids
clk: rockchip: rename rga clock-id on rk3399
clk: rockchip: add general gpu soft-reset on rk3399
clk: rockchip: fix the gate bit for i2c4 and i2c8 on rk3399
clk: rockchip: fix of spelling mistake on unsuccessful in pll clock type
The cifout clock is incorrect due to the manual error, we need to
fix it.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We don't need to many clocks enable after startup, to reduce some
power consumption.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch add some necessary frequencies for the RK3399 clock.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The gate bits of the i2c4 and i2c8 are incorrect due to the manual
error, we need to fix them.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
fix spelling mistake, unsucessful -> unsuccessful
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3399 header and also in the clock code itself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXFzXaAAoJEPOmecmc0R2BfoIH/jzxzuOFb7oMIEjWA1Dlv6ev
I9l63Pi5+/BGXMXkuvBCpyVKRk9T7jyAkQbvMuoo6ELOmEtn2AX4BC7Pq+xok7Xz
WZZQY/+nkYaAjJ6GscLpqWtNlhwCY0Ms/1WOp9DwTwcDztiTJaa9iQf5CELEJMhg
RfANV2DIi9mNh+Nx4JIQi2e01tN2EXUsSNH8NVKTqfZKR/hvb9KO3qQWQzGdgqPr
jNaAuVIq1iOIV0fBD7X8WJwQ2JqmrP7UsvIAXYk46E53jSk5RvnrGIvFp23pu0Jc
0a677jCpx09en6LLPXQOwgtx687hChP5HT466BXo241daJkX4isDKAx430p7hGY=
=99uY
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull some checkpatch silencers from Heiko Stuebner:
Fix quite some checkpatch warnings in the newly added
rk3399 header and also in the clock code itself.
* tag 'v4.7-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix checkpatch warning in core code
clk: rockchip: drop unnecessary header comment
clk: rockchip: reign in some overly long lines in the rk3399 controller
clk: rockchip: fix checkpatch errors in rk3399 dt-binding header
We seem to have accumulated a bunch of checkpatch warnings, with mainly
overlong lines and two unnecessary allocation error messages.
Most were introduced with the recent multi-controller-support but some
were quite a bit older.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The internal clk header did contain a comment indicating that some of the
defined registers were shared over multiple clock controller variants.
In recent times, it was simply extended all the time and stopped providing
any meaningful information, so drop it and it's overlong line.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We allow overlong lines in the array portitions describing the clock
trees to ease readability by having each element always at the same
position. But the rest of the code should honor the 80 char limit.
Fix the newly added rk3399 clock code to respect that.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Main change is probably the added support for the new rk3399 soc
and necessary infrastructure changes surrounding it.
The biggest chunk is probably that clock code is now able to
handle multiple clock providers in one system, as the rk3399
has two of those. A general one and another smaller one in a
separate power domain. The rk3399 also uses another new pll type.
Thankfully it just fits nicely into our current structure.
It also needs some parts like the cpuclk mux parameters to be
a bit more flexible and an new fractional divider subtype without
gate.
Apart from this big change we have some more fixes and removal
of forgotten variables.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXDHdWAAoJEPOmecmc0R2BrSAIAIf3g2D84lSEYPDfjLCPHKWQ
vdmBG/J53+OqFfk0IgYFPcgFfXsgXX0iv34WgtxDOQ1uF+uPDC1KQFlyNrg3E8Mu
7yUzHewphWumgtun/niThjhKTH+fRAZV4koo35KndXpsOXAy87uW+PZc+0f33ocD
FzF8mu3eQGsXNkZ3NM/BlLN38gfQVFLiiBNxg/yPmIGqI4VcWJPVUWr51nOURL78
5NozCjr1giUXPazat0IzsvGdO9szben7al2MixufnpkojjQkB+C8r2lxVXPSC7xH
EWHPj8WVS0eLYLPW6T3t27zvLNRuORzv5y7cHS8TMc4en1qFS5NJ56ruRv7SzNQ=
=kC1q
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk updates from Heiko Stuebner:
This is first big chunk of Rockchip clock-related changes for 4.7.
Main change is probably the added support for the new rk3399 soc
and necessary infrastructure changes surrounding it.
The biggest chunk is probably that clock code is now able to
handle multiple clock providers in one system, as the rk3399
has two of those. A general one and another smaller one in a
separate power domain. The rk3399 also uses another new pll type.
Thankfully it just fits nicely into our current structure.
It also needs some parts like the cpuclk mux parameters to be
a bit more flexible and an new fractional divider subtype without
gate.
Apart from this big change we have some more fixes and removal
of forgotten variables.
* tag 'v4.7-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: add clock controller for the RK3399
dt-bindings: add bindings for rk3399 clock controller
clk: rockchip: add dt-binding header for rk3399
clk: rockchip: release io resource when failing to init clk
clk: rockchip: remove redundant checking of device_node
clk: rockchip: fix warning reported by kernel-doc
clk: rockchip: remove mux_core_reg from rockchip_cpuclk_reg_data
clk: rockchip: add new pll-type for rk3399 and similar socs
clk: rockchip: Add support for multiple clock providers
clk: rockchip: allow varying mux parameters for cpuclk pll-sources
clk: rockchip: add a COMPOSITE_FRACMUX_NOGATE type
The rockchip_softrst_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the clock tree definition for the new RK3399 SoC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
