The firmware rt5677_elf_vad is an ELF binary obtained from
request_firmware(). Sections of the ELF are loaded to
the DSP via SPI. A model (e.g. en_us.mmap) can optionally be
loaded to the DSP at RT5677_MODEL_ADDR to overwrite the
baked-in model in rt5677_elf_vad.
Then we switch to DSP mode, load firmware, and let DSP run.
When a hotword is detected, an interrupt is fired and
rt5677_irq() is called. When 'DSP VAD Switch' is turned off,
the codec is set back to normal mode.
The kcontrol 'DSP VAD Switch' is automatically enabled/disabled
when the hotwording PCM stream is opened/closed.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Audmix support two substream, When two substream start
to run, the trigger function may be called by two substream
in same time, that the priv->tdms may be updated wrongly.
The expected priv->tdms is 0x3, but sometimes the
result is 0x2, or 0x1.
Fixes: be1df61cf0 ("ASoC: fsl: Add Audio Mixer CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1e706afe53fdd1fbbbc79277c48a98f8416ba873.1573458378.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Set L1SEN to make sure the system can enter S0ix, and restore it on
resume.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170916.26517-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add check to avoid possible NULL pointer dereference issue.
This issue was reported by static analysis tools, we didn't face this
issue but we can't rule it out either as a false positive.
Reported-by: Keqiao Zhang <keqiao.zhang@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170916.26517-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch switches from .txt base to .yaml base Document for FSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/878sp4jaqy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the example SOF amp widget topology, KASAN dumps this
when the AMP bytes kcontrol gets loaded:
[ 9.579548] BUG: KASAN: slab-out-of-bounds in
sof_control_load+0x8cc/0xac0 [snd_sof]
[ 9.588194] Write of size 40 at addr ffff8882314559dc by task
systemd-udevd/2411
Fix that by rejecting the topology if the bytes data size > max_size
Fixes: 311ce4fe76 ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145816.9367-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_unregister_component() is calling snd_soc_lookup_component()
under mutex_lock(). But, snd_soc_lookup_component() itself is using
mutex_lock(), thus it will be dead-lock.
This patch adds _nolocked version of it, and avoid dead-lock issue.
Fixes: ac6a4dd3e9f0("ASoC: soc-core: use snd_soc_lookup_component() at snd_soc_unregister_component()")
Reported-by: "kernelci.org bot" <bot@kernelci.org>"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87bltph4da.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SOF module load/unload tests show nasty recurring warnings:
WARNING: CPU: 5 PID: 1339 at sound/core/control.c:466
snd_ctl_remove+0xf0/0x100 [snd]
RIP: 0010:snd_ctl_remove+0xf0/0x100 [snd]
This regression was introduced by the removal of the call to
soc_remove_link_components() before soc_card_free() is invoked.
Go back to the initial order but only call
soc_remove_link_components() once.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Fixes: 5a4c9f054c ("ASoC: soc-core: snd_soc_unbind_card() cleanup")
GitHub issue: https://github.com/thesofproject/linux/issues/1424
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145801.9316-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the example SOF amp widget topology, KASAN dumps this
when the AMP bytes kcontrol gets loaded:
[ 9.579548] BUG: KASAN: slab-out-of-bounds in
sof_control_load+0x8cc/0xac0 [snd_sof]
[ 9.588194] Write of size 40 at addr ffff8882314559dc by task
systemd-udevd/2411
Fix that by rejecting the topology if the bytes data size > max_size
Fixes: 311ce4fe76 ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145816.9367-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dobj is used only when SND_SOC_TOPOLOGY was selected.
Let's enable it under SND_SOC_TOPOLOGY.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87o8xq251d.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc-core has some API which is used from topology, but it is doing
topology specific operation at soc-core.
soc-core should care about core things, and topology should care
about topology things, otherwise, it is very confusable.
For example topology type is not related to soc-core,
it is topology side issue.
This patch removes meaningless check from soc-core.
This patch keeps extra initialization/destruction at
snd_soc_add_dai_link() / snd_soc_remove_dai_link()
which were for topology.
From this patch, non-topology card can use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87pni6251h.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC has 2 functions.
snd_soc_register_dai() is used from topology
snd_soc_register_dais() is used from snd_soc_add_component()
In general, people think like _dai() is called from _dais()
with for loop. But in reality, these are very similar
but different implementation.
We shouldn't have duplicated and confusing implementation.
This patch calls snd_soc_register_dai() from snd_soc_register_dais()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87r22m251l.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC has 2 functions.
snd_soc_register_dai() is used from topology
snd_soc_register_dais() is used from snd_soc_add_component()
In general, people think like _dai() is called from _dais()
with for loop. But in reality, these are very similar
but different implementation.
We shouldn't have duplicated and confusing implementation.
snd_soc_register_dai() is now used from topology.
But to reduce duplicated code, it should be used from _dais(), too.
Because of topology side specific reason,
it is calling snd_soc_dapm_new_dai_widgets(),
but it is not needed _dais() side.
This patch factorizes snd_soc_register_dai() to
topology / _dais() common part, and topology specific part.
And do topology specific part at soc-topology.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87sgn2251p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC has 2 functions.
snd_soc_register_dai() is used from topology
snd_soc_register_dais() is used from snd_soc_add_component()
In general, people think like _dai() is called from _dais()
with for loop. But in reality, these are very similar
but different implementation.
We shouldn't have duplicated and confusing implementation.
snd_soc_register_dai() is now used from topology.
But to reduce duplicated code, it should be used from _dais(), too.
To prepare it, this patch adds missing parameter legacy_dai_naming
to snd_soc_register_dai().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87tv7i251u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and is difficult to debug.
This patch adds missing soc_del_dai() and snd_soc_unregister_dai().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87v9ry251z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves snd_soc_unregister_dais() next to
snd_soc_register_dais().
This is prepare for snd_soc_register_dais() cleanup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87woce2524.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves snd_soc_register_dai() next to
snd_soc_register_dais().
This is prepare for snd_soc_register_dais() cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87y2wu2528.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_unregister_component() is now finding component manually,
but we already have snd_soc_lookup_component() to find component;
Let's use existing function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87zhha252c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc-core has
snd_soc_add_component(), snd_soc_component_add(),
snd_soc_del_component(), snd_soc_component_del().
These are very confusing naming.
snd_soc_component_xxx() are called from snd_soc_xxx_component(),
and these are very small.
Let's merge these into snd_soc_xxx_component(), and
remove snd_soc_component_xxx().
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/871rum3jmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and is difficult to debug.
Now ALSA SoC has snd_soc_add_component(), but there is no paired
snd_soc_del_component(). Thus, snd_soc_unregister_component() is
calling cleanup function randomly. it is difficult to read.
This patch adds missing snd_soc_del_component_unlocked() and
balance up code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/8736f23jn4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_lookup_component() is using mix of continue and break
in the same loop. It is odd.
This patch cleanup it.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/874kzi3jn8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves snd_soc_lookup_component() to upper side.
This is prepare for snd_soc_unregister_component()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/875zjy3jnd.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
ALSA SoC has soc_bind_dai_link(), but its paired soc_unbind_dai_link()
is not implemented.
More confusable is that soc_remove_pcm_runtimes() which should be
soc_unbind_dai_link() is implemented without synchronised
to soc_bind_dai_link().
This patch cleanup this unbalance.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/877e4e3jni.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we focus to soc_bind_dai_link() at snd_soc_instantiate_card(),
we will notice very complex operation.
static int snd_soc_instantiate_card(...)
{
...
/*
* (1) Bind dai_link via card pre-linked dai_link
*
* Bind dai_link via card pre-linked.
* 1 dai_link will be 1 rtd, and connected to card.
* for_each_card_prelinks() is for card pre-linked dai_link.
*
* Image
*
* card
* - rtd(A)
* - rtd(A)
*/
for_each_card_prelinks(card, i, dai_link) {
ret = soc_bind_dai_link(card, dai_link);
...
}
...
/*
* (2) Connect card pre-linked dai_link to card list
*
* Connect all card pre-linked dai_link to *card list*.
* Here, (A) means from card pre-linked.
*
* Image
*
* card card list
* - rtd(A) - dai_link(A)
* - rtd(A) - dai_link(A)
* - ... - ...
*/
for_each_card_prelinks(card, i, dai_link) {
ret = snd_soc_add_dai_link(card, dai_link);
...
}
...
/*
* (3) Probe binded component
*
* Each rtd has many components.
* Here probes each rtd connected components.
* rtd(A) in Image is the probe target.
*
* During this component probe, topology may add new dai_link to
* *card list* by using snd_soc_add_dai_link() which is
* used at (2).
* Here, (B) means from topology
*
* Image
*
* card card list
* - rtd(A) - dai_link(A)
* - rtd(A) - dai_link(A)
* - ... - ...
* - dai_link(B)
* - dai_link(B)
*/
ret = soc_probe_link_components(card);
...
/*
* (4) Bind dai_link again
*
* Bind dai_link again for topology.
* Note, (1) used for_each_card_prelinks(),
* here is using for_each_card_links()
*
* This means from card list.
* As Image indicating, it has dai_link(A) (from card pre-link)
* and dai_link(B) (from topology).
* main target here is dai_link(B).
* soc_bind_dai_link() ignores already used
* dai_link (= dai_link(A))
*
* Image
*
* card card list
* - rtd(A) - dai_link(A)
* - rtd(A) - dai_link(A)
* - ... - ...
* - rtd(B) - dai_link(B)
* - rtd(B) - dai_link(B)
*/
for_each_card_links(card, dai_link) {
ret = soc_bind_dai_link(card, dai_link);
...
}
...
}
As you see above, it is doing very complex method.
The problem is binding dai_link via "card pre-linked" (= (1)) and
"topology added dai_link" (= (3)) are separated.
The code can be simple if we can bind dai_link when dai_link
is connected to *card list*.
This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/878sou3jnn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_is_dai_link_bound() check will be called both
*before* soc_bind_dai_link() (A), and
*under* soc_bind_dai_link() (B).
These are very verbose code. Let's remove one of them.
* static int soc_bind_dai_link(...)
{
...
(B) if (soc_is_dai_link_bound(...)) {
...
return 0;
}
...
}
static int snd_soc_instantiate_card(...)
{
...
for_each_card_links(...) {
(A) if (soc_is_dai_link_bound(...))
continue;
* ret = soc_bind_dai_link(...);
if (ret)
goto probe_end;
}
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87a79a3jns.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_init_dai_link() is needed to be called before soc_bind_dai_link().
int snd_soc_instantiate_card()
{
for_each_card_prelinks(...) {
(1) ret = soc_init_dai_link(...);
...
}
...
for_each_card_prelinks(...) {
(2) ret = soc_bind_dai_link(...);
...
}
...
for_each_card_links(...) {
...
(A) ret = soc_init_dai_link(...);
...
(B) ret = soc_bind_dai_link(...);
}
...
(1) is for (2), and (A) is for (B)
(1) and (2) are for card prelink dai_link.
(A) and (B) are for topology added dai_link.
soc_init_dai_link() is sanity check for dai_link, not initializing today.
Therefore, it is confusable naming. We can rename it as sanity_check.
And this check is for soc_bind_dai_link().
It can be more simple code if we can call it from soc_bind_dai_link().
This patch renames it to soc_dai_link_sanity_check(), and
call it from soc_bind_dai_link().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87d0e63joh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves soc_init_dai_link() next to soc_bind_dai_link().
This is prepare for soc_bind_dai_link() cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87eeym3joq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADAU7118 has an example where the codec has an i2c address of 14, and
the unit address set to 14 as well.
However, while the address is expressed in decimal, the unit-address is
supposed to be in hexadecimal, which ends up with two different addresses
that trigger a DTC warning. Fix this by setting the address to 0x14.
Cc: Nuno Sá <nuno.sa@analog.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 969d49b2cd ("dt-bindings: asoc: Add ADAU7118 documentation")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105105615.21391-1-maxime@cerno.tech
Signed-off-by: Mark Brown <broonie@kernel.org>
Set trigger order for FE DAI links to SND_SOC_DPCM_TRIGGER_POST
to trigger the BE DAI's before the FE DAI's. This prevents the
xruns seen on playback pipelines using the link DMA.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191104224812.3393-3-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the trigger orders SND_SOC_DPCM_TRIGGER_PRE/POST
determine the order in which FE DAI and BE DAI are triggered.
In the case of SND_SOC_DPCM_TRIGGER_PRE, the FE DAI is
triggered before the BE DAI and in the case of
SND_SOC_DPCM_TRIGGER_POST, the BE DAI is triggered before
the FE DAI. And this order remains the same irrespective of the
trigger command.
In the case of the SOF driver, during playback, the FW
expects the BE DAI to be triggered before the FE DAI during
the START trigger. The BE DAI trigger handles the starting of
Link DMA and so it must be started before the FE DAI is started
to prevent xruns during pause/release. This can be addressed
by setting the trigger order for the FE dai link to
SND_SOC_DPCM_TRIGGER_POST. But during the STOP trigger,
the FW expects the FE DAI to be triggered before the BE DAI.
Retaining the same order during the START and STOP commands,
results in FW error as the DAI component in the FW is still
active.
The issue can be fixed by mirroring the trigger order of
FE and BE DAI's during the START and STOP trigger. So, with the
trigger order set to SND_SOC_DPCM_TRIGGER_PRE, the FE DAI will be
trigger first during SNDRV_PCM_TRIGGER_START/STOP/RESUME
and the BE DAI will be triggered first during the
STOP/SUSPEND/PAUSE commands. Conversely, with the trigger order
set to SND_SOC_DPCM_TRIGGER_POST, the BE DAI will be triggered
first during the SNDRV_PCM_TRIGGER_START/STOP/RESUME commands
and the FE DAI will be triggered first during the
SNDRV_PCM_TRIGGER_STOP/SUSPEND/PAUSE commands.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191104224812.3393-2-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not support mmap in S/PDIF mode. In S/PDIF mode
the buffer has to be copied, to allow the channel status
bits insertion.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191104133654.28750-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The same driver is reused for 3 different configurations, but the
driver will only be build if ApolloLake is selected.
Fix and make sure each device can work without dependencies on others
(useful for minimal configurations).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This option is only required with the Skylake platform driver, there
is no reason to have this option in machine drivers. This is
e.g. useless for SOF-based solutions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This option famously broke audio on Linus' laptop and the problem have
not been fixed.
Mark as DEPRECATED to avoid any ambiguity with distros.
Use SOF if you need HDaudio support w/ the DSP enabled, e.g. for DMIC
capture.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
So far we used select to use the relevant built-in/module options, but
this led to blurring layers between core and Intel Kconfigs.
Use def_tristate works just as well and removes Intel stuff from the code.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
updated solution to the problem reported with randconfig:
CONFIG_SND_SOC_SOF_IMX depends on CONFIG_SND_SOC_SOF, but is in
turn referenced by the sof-of-dev driver. This creates a reverse
dependency that manifests in a link error when CONFIG_SND_SOC_SOF_OF
is built-in but CONFIG_SND_SOC_SOF_IMX=m:
sound/soc/sof/sof-of-dev.o:(.data+0x118): undefined reference to `sof_imx8_ops'
use def_trisate to propagate the right settings without select.
Fixes: f4df4e4042 ("ASoC: SOF: imx8: Fix COMPILE_TEST error")
Fixes: 202acc565a ("ASoC: SOF: imx: Add i.MX8 HW support")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some distros select all possible options, despite existing warnings to
be careful. This leads to e.g. user reports that the HDaudio codec and
DMIC are not handled by SOF.
Add an explicit menu item to unlock developer options, and make them
dependent on CONFIG_EXPERT. Hopefully with this double-lock these
options will only be selected by developers.
GitHub issue: https://github.com/thesofproject/sof/issues/1885
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some distros select all options blindly, which leads to confusion and
bug reports. SOF does not fully support Broadwell due to firmware
dependencies, the machine drivers can only support one option, and
UCM/topology files are still being propagated to downstream distros,
so make SOF on Broadwell an opt-in option that first require distros
to opt-out of existing defaults.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204237
Fixes: f35bf70f61 ('ASoC: Intel: Make sure BDW based machine drivers build for SOF')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some distros select all options blindly, which leads to confusion and
bug reports. Since SOF does not support Baytrail-CR for now, and
UCM/topology files are still being propagated to downstream distros,
make SOF on Baytrail an opt-in option that first require distros to
opt-out of existing defaults.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101173045.27099-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the retry argument for the hda_dsp_wait_d0i3c_done()
function and use the HDA_DSP_REG_POLL_RETRY_COUNT macro
directly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170916.26517-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Machine driver to enable
RT5682 on SSP0, DMIC, HDMI and
RT1011 AMP on SSP1 with
2 CH / 24 bit TDM Playback over 4 individual codecs and
4 CH / 24 bit Capture to provide feedback.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101171847.26767-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add match for CML m/c with RT1011 and RT5682
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101171847.26767-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
